Overclocking q9300 on MSI P35 Neo2-FR

Hi there, 
I'm after a bit of advice on overclocking my processor.
I've got a Msi P35 Neo2-FR motherboard, Corsair 4GB (2x2GB) PC2-6400 XMS2 DHX (4-4-4-12) Memory, a 650w power supply and a Quad core Q9300.
My aim is to overclock the q9300 to 3ghz. Could you please give me info on what settings you'd set the following to.
cpu voltage,
vtt fsb voltage,
nb voltage,
sb I/O power,
sb core power,
Thanks for any help. I'm just worried that I use the wrong setting resulting in a mini nuclear explosion. 

Look here: http://global.msi.com.tw/index.php?func=techexpressdesc2&express_no=52&page=2

Similar Messages

  • MSI P35 Neo2-FR/FIR wont overclock

    This might be a simple question but here it is. My new MSI p35 bios v 1.34 wont allow me to overclock my q66oo. I think the problem is windows xp pro 64. I cant install the MSI dual core center or the live monitor. When I am in the bios I canot change these setting inside the cell menu,
    cpu fsb frequency
    adjust cpu ratio
    cpu voltage
    memory voltage
    vtt fsb voltage
    nb voltage
    sb i/o power
    sb core power
    Any ideas?
    MSI P35 Neo2-Fr
    intel q6600
    evea 8800 gt
    g. skill 1 gig pc2 6400 2 sticks
    corsair hx620w

    Keep us updated on your progress.

  • Msi p35 neo2 fr motherboard - system freezes

    Hello , I just bought a Msi p35 neo2 fr motherboard and I have this problem . My system randomly freezes ,no errors ,no blue
    screens  and I have to restart it . I tried each module of ram separately and I got the same problem .
    The video card worked fine on my old system and I don`t think this could be . Also the standby led (led 3 ) is always on and red
    Maybe I messed up the " wire up "  . I could use some tips about how to properly wire up and which settings should be done in BIos for my configuration ?
    Msi p35 neo2 fr
    PSU Sirtec HPC-430-P12S V2.2
    2x1 gb Geil pc6400 800 mhz
    video geforce 6200 128 mb
    hdd sata 120 gb

    from the User Manual:
    Quote
    Spread Spectrum
    When the motherboard’s clock generator pulses, the extreme values (spikes) of the
    pulses creates EMI (Electromagnetic Interference). The Spread Spectrum function
    reduces the EMI generated by modulating the pulses so that the spikes of the pulses
    are reduced to flatter curves. If you do not have any EMI problem, leave the setting at
    [Disabled] for optimal system stability and performance. But if you are plagued by EMI,
    select the desired range for EMI reduction. Remember to disable Spread Spectrum
    function if you are overclocking, because even a slight jitter can introduce a temporary
    boost in clock speed which may just cause your overclocked processor to lock
    up."

  • MSI P35 Neo2-Fr -- can't get onboard audio device to appear in XP

    I've just installed XP sp3 onto my new mobo (MSI P35 Neo2-Fr).
    Attached is Q6600 core2 quad processor, 2GB memory (DDR2), ATI HD4850 gfx card. I haven't changed the bios much at all or overclocked anything yet.
    All seems fine *except* that I can't windows XP to see that there's an onboard audio device.
    (It is enabled in the bios btw.) I've tried installing the high def audio driver on the CD from mobo box, and also downloaded the latest from the MSI site. I uninstall the driver and reboot before trying to reinstall it again btw.
    The audio driver installer used to say there was a problem installing the driver, but it doesn't any more. After installing it and rebooting, XP control panel -> Audio devices says there are no audio devices.
    Also, I notice that there should be an extra audio item in the XP control panel (according to mobo manual), but this hasn't appeared.
    In XP's system hardware list there are no sound devices under Sound, but there are two unknown PCI devices (with yellow question marks next to them).
    Any suggestions?
     

    Quote from: Del UK on 05-September-08, 05:13:05
    Had same issue with ATI card installed.
    Go to Microsoft update and choose custom
    You should see a list with hardware updates..........
    After that, all will be fine
    Hi there
    Thanks for your reply. I went to MS updates, didn't see any in custom about hardware (apart from updated ethernet driver). Installed all updates anyway. And the problem remains...

  • MSI P35 NEO2 FIR voltage problems!!

    Let's start:
     I have MSI P35 NEO2 FIR ,e5200,2 x Geil ultra plus 1066+,as us 2900CT,lcpower 6550g and...rest- not so important for my questions.
    1.My problem is next: default voltage values for my RAM is ~2.2-2.4 every time I check in windows (speedfun,sisoft Sandra, everest..)shows me 2.0 or some time even 1.8v  . When i change voltage in bios and went to win voltage on RAM is still unchanged (2.0v)  .
    Same thing happen with NB voltage. But CPU voltage I can change freely with no problem.
    When I change fsb(try to overclock) suddenly memory voltage rises how i do not now  , but only to 2.35 and no more.
    Can anyone help me fix this problem because my memory is not stable at 2.0 or 1.8 sometimes and system crashes?
    2.When i change cpu settings from 12.5*200 to (example)10*300 in windows even in system properties see that my current clock is 12.5*300=3750 and not 10*300=3000 like it should be .
    Is it bios problem?
    My bios version is 1.9.
    Thanks!

    same problem with the Neo2 FR (like mine). After quite of bit of researching and testing i reckon that software can not correctly read the vRAM on these MSI boards. I found that Speedfan, Everest, and HardwareMonitor all gave an incorrect reading for my RAM's voltage. Also, if i increased the cpu voltage in the BIOS then the voltage monitoring programs would show an increase in CPU voltage and RAM voltage (even though i had not changed the latter).

  • Msi p35 neo2-fr disable EIST in bios

    hello !
    My name is Adrian. My system spec.:
    msi p35 neo2-fr (bios ver.1.A),
    CPU core 2 duo E8400 C0
    mem. dual chanel kit 2x2GB geil pristine ddr2 800
    2x250 hdd western digital WD2500YS
    Video Gigabyte GV-NX88T512HP 8800GT 512 DDR3
    Sound Creative Sound Blaster Audigy SE
    PSU Chieftec 450W 2x12v: 36 amp., 5v: 25 amp.
    OS dual boot windows xp sp3 and windows vista sp2
    My problem is when i disable EIST in bios Vista gives me a blue screen (0x0000007F) on boot and XP restarts without any error.
    Any idea ? Thank you anticipated !

    Quote from: pristine on 11-August-09, 12:31:07
    I want to overclock and i want to change the multiplier to make some tests ! And i can`t do that without EIST DISABLED !
    OK, stay calm.  Getting frustrated is only going to make people not reply.
    I'm not sure why disabling EIST is giving you a BSOD.  I don't think anyone has any ideas since you have no real replies.
    A kernel trap is hardware failure usually.  Makes me think when you disable EIST, the machine becomes unstable.   Are you setting the default multiplier for your processor?  Hell, we don't even know what it is.  How about you list your rig specs?
    Just to add:  Overclocking with EIST enabled is pretty much the same.  You save power, so I don't know why you'd want to turn it off, in all honesty.

  • MSI P35 Neo2 FR... DOA?

    OKay, I just tried to set up this combo:
    E6550
    MSI P35 Neo2 FR
    MSI HD 3850
    2x2GB Teamgroup Elite CL5
    OCZ Stealthstream 600W
    Unfortunately the system does nothing when I hit the power button. Only the standby LED is on, nothing else happens, not even the fans start spinning. The diagnostic LEDs dont light up either, simply nothing happens.
    This is what I have already tried:
    Different case, with different power button
    Tried different RAM
    I tried the PSU in another system, works flawlessly
    I checked all cables and connections, everything is installed properly
    I set the FSB jumper to 333MHz
    But in general, if any other component would be faulty, the mobo would at least beep or the diagnostic LEDs would show a problem. But in this case the system refuses to start.
    What could be the problem here?

    Quote from: Streifenkarl on 09-December-07, 23:49:21
    OKay, I just tried to set up this combo:
    E6550
    MSI P35 Neo2 FR
    MSI HD 3850
    2x2GB Teamgroup Elite CL5
    OCZ Stealthstream 600W
    Unfortunately the system does nothing when I hit the power button. Only the standby LED is on, nothing else happens, not even the fans start spinning. The diagnostic LEDs dont light up either, simply nothing happens.
    This is what I have already tried:
    Different case, with different power button
    Tried different RAM
    I tried the PSU in another system, works flawlessly
    I checked all cables and connections, everything is installed properly
    I set the FSB jumper to 333MHz
    But in general, if any other component would be faulty, the mobo would at least beep or the diagnostic LEDs would show a problem. But in this case the system refuses to start.
    What could be the problem here?
    How high could your overclock with 2GBx2 RAM?

  • MSI P35 Neo2-FR

    Hi
    MSI P35 Neo2-FR v1.1 Bios 1.1
    cpu e4300
    intial findings on 200 FSB jumper 9x356 takes 1.4v on NB to get into windows
    9x356 on 266 FSB jumper takes stock(1.250)
    Some questions, what is a safe voltage to run on the p35 chipset and on this board? Also the board defaults to 2t command rate, and I can see nowhere to select or change, where/can you change to 1t.
    In Bios, there is a setting  "Auto disable Dimm/PCI Frequency"   what does this do?
    thanks in advance

    Changing the straps causes the chipset to use tighter or looser timings. Why the excessive voltage is required on 200FSB strap.
    The auto disable is the PCI frequency lock, it's best enabled whenever overclocking.

  • MSI P35 Neo2-FR + 2x2GB RAM

    1. I'm about to order that combo (MSI P35 Neo2-FR and 2x2GB TeamGroup Elite PC2-6400U CL5-5-5-15), but before I hit the Buy button I want to ask if the MSI motherboard has any known problems with 2GB sticks.
    I intend to run the system @ 400MHz FSB so the memory can run at its rated speed 1:1.
    2. What BIOS version is recommended here?
    3. Does anyone know if the Asus Triton 75 heatsink fits in between all those motherboard heatsinks and heatpipes?

    Quote from: AaronYuri on 06-December-07, 04:39:02
    Well if 2GB sticks didn't work good with the board what would be the point of the bundle?
    I dont understand that remark. Thats the point of this thread, will 4GB work good on the MSI P35?
    The CPU will be an E6550.
    As for 400MHz, I really hope that MSI didnt make another P965 Platinum here, which has a poor overclocking potential. 400MHz FSB is nothing for my Abit QuadGT and most other P965/P35 based motherboards.
    I will be really pissed if the P35 Neo2 wont be able to reach 400MHz FSB.

  • Need Help with ESATA on MSI P35 Neo2-FR

    I have the MSI P35 Neo2-FR motherboard http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=&cat3_no=&prod_no=1261 and trying to get the eternal ESATA to work.  It works with one individual HD.  I'm using an external ESATA drive with 3 HD inside the external case with one cable running into the external ESATA in the back of the motherboard.  It's only recognizing 1 drive and the other 2 isn't showing up.  If I switch it to USB connection it will read all 3 drives.  I'm running windows 7 x64 but it recognize on my other 2 computers with a different motherboard. I have install it with the ACHI setup in Bios and I've also install the Matrix Storage Controller after installation.  I never install the Intel ICH9R SATA RAID driver where you have to press the F6 to install it.  Is that what I'm missing and is taht needed for the ESATA to work?    I'm getting this message "A storage device was connected. If this device is a port multiplier, only port 0 of the port multiplier will be active." Been googling all day and still can't figure out what I'm missing.
    Any help would greatly be appreciated.

    Quote
    For some reason this board is Bios only have IDE, RAID and ACHI and I don't see a SATA.
    IDE, RAID and AHCI are operating modes of the SATA Controller.  Everything okay here.
    Quote
    Seems to me it's either this board and it's driver don't let you use the port multiplier but it suppose to support port multiplier.
    It is neither the board, nor is it the driver.  It is a limitation of the Intel ICH9R Chipset.  You will have the same problem on all P35/ICH9R based mainboards.  Read here:
    http://xtreview.com/addcomment-id-788-view-intel-technology-matrix-RAID-and-port--multiplier.html
    Quote
    Unfortunately, used in the south bridges ICH9R the version of such technology provides access only to one hard disk at the specific moment of time. . The technology became more complex to realize , which implies to several access disks simultaneously, possesses higher cost and more higher central processor loads , therefore it can be rejected.
    Here is the same problem on a Gigabyte GA-P35-DQ6:
    http://forums.overclockers.co.uk/showthread.php?p=11892094
    Nothing you can do about it.

  • Installing MSI P35 Neo2-FR

    Hello
    I'm installing Q6600 on my MSI P35 Neo2-FR mainboard. In the user guide it says (2-3, 2-4):
    - "Make sure that you apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation"
    - "Remember to apply some thermal paste on it for better heat dispersion"
    - "Meanwhile, do not forget to apply some thermal paste on CPU before installing the heat sink/cooler fan for better heat dispersion."
    I'm feeling less confident in installing my Q6600 now without this thermal paste, since it's explicitly *recommended* in the guide. What would happen if I did not apply the paste?

    Quote
    What would happen if I did not apply the paste?
    The heat the processor generates would not be properly dissipated to the heatsink.  In a worst case scenario your CPU could shutdown automatically because of overheating and/or be damaged.
    Have a look at your heatsink itself.  Often thermal paste or some sort of thermal pad is pre-applied for easier installation.
    If there is not such thing get some thermal paste before you install CPU+heatsink.

  • MSI P35 NEO2-FIR, Traces of fire...

    Hello,
    During dust cleanup of my PC. I noticed a burned part of my MSI P35 Neo2-FIR mobo, i wonder if it is still save to use now, maybe someone have any idea what does that 'chip?' is responsible for ?
    Photos:

     It looks like it's a resistor in the +5V power circuit to JUSB1. Must have been something plugged into it at one time or another that short circuited/overloaded it it and fried the resistor. What was plugged into the JUSB1 header? If all else is OK if you need to use any front panel USB device you can use JUSB2 or 3 instead. Get a volt meter and check the PSU for correct voltage of +5V to see if PSU is still OK as whatever caused that damage may have also damaged PSU.

  • Have MSI P35 Neo2-FR mobo, want 8GB RAM (4x2GB), anybody knows compatible ram?

    I have MSI P35 Neo2-FR motherboard and want to buy 8GB ram, preferably 4x2GB(2x2GB + 2x2GB). Anybody has such a setup and can recomend some RAM?
    I dont want to buy some random ram, because the motherboards are very picky when youn install the maximum supported ram.

    Crucial tend to have quite compatible RAM across boards. On their site you can enter your motherboard model to find the RAM that is compatible. A gave it a run and the following is compatible:
    Part #: CT2KIT25664AA667 • DDR2 PC2-5300 • CL=5 • Unbuffered • NON-ECC • DDR2-667 • 1.8V • 256Meg x 64
    Part #: CT2KIT25664AA800 • DDR2 PC2-6400 • CL=6 • Unbuffered • NON-ECC • DDR2-800 • 1.8V • 256Meg x 64
    Part #: CT2KIT25664AA1067 • DDR2 PC2-8500 • CL=7 • Unbuffered • NON-ECC • DDR2-1066 • 1.8V • 256Meg x 64
    Part #: BL2KIT25664AA80A • DDR2 PC2-6400 • 4-4-4-12 • Unbuffered • NON-ECC • DDR2-800 • 2.0V • 256Meg x 64
    Part #: BL2KIT25664AL80A • DDR2 PC2-6400 • 4-4-4-12 • Unbuffered • NON-ECC • DDR2-800 • 2.0V • 256Meg x 64
    Part #: BL2KIT25664AR80A • DDR2 PC2-6400 • 4-4-4-12 • Unbuffered • NON-ECC • DDR2-800 • 2.0V • 256Meg x 64
    The above are all 4GB kits so obviously you'd need to buy two packs to get the 8GB.
    http://www.crucial.com/uk/store/listparts.aspx?model=P35%20Neo2-FR/FIR
    You do need a 64-bit OS to access the full 4GB or 8GB so also bear that in mind.

  • MSI P35 Neo2-FR do i need JPWR1 Connected for 2 x ATI Radeon 3850 256mb cards ?

    hello,
           Ive recently Brought a MSI P35 Neo2-FR motherboard and been running in single Sapphire 3850 256mb so decided to install my second Sapphire 3850 256mb.
    PSU Ive got is a Hyper Type M 580watt but at moment Ive used all connections 4 pin molex connections and 2 to power second sapphire 3850MB card waiting for reply from hyper about what connection i can put the extender on safely coming off 1 that's used.
    Its running Stable at moment without the JPWR1 connected just wondering if its for high end cards like the 2900XT that use's a lot more power then the 3850 and 3870's
    Scores I'm getting so far are with a Intel Core 2 duo E8200
    Single card         - 3DMark 2006 - 9436 3DMarks
    Crossfire enabled - 3DMark 2006 - 12356 3DMarks
    Are these scores about right too ?

    Quote from: Del UK on 17-February-08, 04:42:47
    Which PSU, do you use Kimpsu?
    Would have a guess it's dual +12V rail......
    Antec or Seasonic.......
    My current PSU is an Antec NeoHE 550W (though I've had many others too, like Zalman, Seasonic and Enermax), so in theory it has three 12V rails, 18A each. Well, of course it cannot feed 18A on each rail simultaneously, but still considering that's the limit, the limit should not be a bottle-neck. Luckily they are devided logically enough, one rail for the directly attached cables (which is the motherboard really) and two for the five detachable cables. And the two rails are logically divided, so putting my PCI-e cables at both ends I get pretty decent amps for two GFX cards (one rail for each) and the motherboard. The rest (HDDs, optical drives) are then attached to cables connected next to those cables, so in fact HDDs are on one rail together with one GFX card, and optical drives (and my fan controller) is on another rail with the other GFX card. Thus I get pretty even distribution between rails (lucky me).
    It was one of the nicest quiet PSUs at the time of purchase. If I were to buy a PSU now I would probably get a Corsair, probably HX520 or HX620, but they have multiple 12V rails... VX series is fine too, only that there are no detachable cables, so although it is an option, I really need to think if I wan't a PSU that only has fixed cables...
    Having multiple rails suck a bit (although on most PSUs they are not really separate rails, but still current limited), but luckily single rail PSUs are coming back after a couple of years of "multi rail fashion".
    And yeah, PSUs made by Seasonic are pretty popular these days, like the Antec NeoHE I have, Corsair HX series, VX450 and so on.
    PS. Good guess, though guessing Antec or Seasonic covers pretty much of the PSUs out there that are of a "quality" brand, at least if Seasonic covers the PSUs made by Seasonic for other companies like Corsair. And I don't mean other suck, just judging by how large % of all quality PSUs are Antec. And yes, there are a few models from Antec that really suck and have high failure rates, and cannot be called quality (like the CWT manufactured Smartpowers and the older Truepowers, also by CWT). Judging by just the company that puts the stickers on the case is not always wise, especially with Antec...
    PPS. Judging from your signature, you have an Enermax and a Corsair VX550 (which is manufactured by CWT I believe). How do you like your Corsair? Is it quiet? I've been considering it as an option to replace my Antec (I'd like to have a single 12V rail). Also the TX-series is an option.

  • MSI P35 Neo2-FR, Im having WEIRD beeps in BIOS continiously unstopping.

    Oh dear lord, i bought a new board and now im having some stupid beeps going off every 3sec in the BIOS, i updated to 1.8 bios and now its going every 1sec, BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP, every time there is a beep the system hangs a bit, i pretty much cant do anything in BIOS and its getting on my nerves. What is causing this? I tried removing all the drives, my cpu fan is connected to molex not to the motherboard though. In windows they go away, a bit when loading windows logo and it hangs the windows logo too for a few times, then all leds go green, before im getting from top to bottom Green, Green, Green, Red, Green

    • Intel Core 2 Quad Q6600 2,40GHz "SLACR G0" + ASUS Silent Knight Copper
    • nVidia XFX Geforce 8800GT 512MB GDDR3 + Zalman VF-1000
    • MSI P35 Neo2-FR
    • 4Gb 2x2Gb A-Data PC6400 800MHz DDR2
    • 1Tb 2x500Gb Samsung Sata II
    • Seasonic 700W M12 Modular
    • Antec Sonata II
    Nothing helps, tried butting a fan into the cpu fan slot, nothing, tryed removing PCI cards, nothing, NOTHING helps, it just keeps beeping and hanging on those beeps in the BIOS. When it gets to windows load screen all is fine, the frick.
    EDIT: Allright, the answer to this problem is, go to windows and do a restart from windows, go to BIOS and there is no more beeping. I did a save and exit and rewent to BIOS and still no beeping, then did the shutdown and power on to BIOS and no beeps. So, weird problem but an easy answer to fix it. I think its something to do with the motherboard booting for the first time, it just needed to go to windows and make a restart. Weeeeeiiiiird.
    Cya, hope this helpes someone in the future.

Maybe you are looking for