Overclocking with MSI KT4 ULTRA

Hi,
I'm currently overclocking my XP 1600+ Palomino to just under an XP 2200+. My Idle temp is 39C and 47C at Load. My CPU is still locked and I'm running at 167FSB x 10.5 = 1758Mhz / 334 Mhz DDR. So far this is the highest stable overclock I am able to get with my current config. I want to get up to atleast a FSB of 180 - 185 to give my GeIL 512MB DDR433 PLATINIUM some sort of challenge, but I can't get the board to post at anything higher than 168FSB. Is it my board topping out or my CPU? What kind of overclocks is everyone else getting with their KT4 ULTRAs? Any help would be greatly appreciated. Thanks )

Hehe so u think all is about MHz!!!????
If u think so go and get some education about overklocking!
I have reached 209FSB!!! Thats overkill!
And im running my system now on the min level x9 Multippel.
And that wil give me a damn strong and powerfull system, I can overklock it to reach the MHz frequence to but i dont right now, i must get a new mobo first, MSI is only !!!
Its up, i wil get a ABIT, or EpOX mobo. then i+ll show u :D
Hmm i have a picture if u want.
But i dont know how to make a link to it, becouse i dont have a webpage now.

Similar Messages

Sata Raid problems with MSI KT4 Ultra Via kt400 chipset

ok i am having major problems setting up my sata raid in my brothers msi KT4 Ultra via KT 400 chipset
it comes up with my irq settings are wrong
my hard drives are WD 120 GB 7200rpms SATA - sold my mobo asus A7N8X - Delux and used my bros mobo above but just cant get them to work if ne one has ne idea on how to fix it (bios is still factory default do i have too flash it to get it too work etc)
would help lots thanx

you dont need multiple threads on the same thing

Urgent help with MSI KT4 Ultra

hey,
off my folks yesterday i got...
MSI KT4 Ultra
512mb DDR333 PC2700
Athlon XP 2600+
Maxtor DiamondMax9 40gb HDD...
i thought i had it all setup right with the HDD in IDE1, DVD and CD-RW in IDE2 and floppy in the floppy bit...
at 1st the CPU cwas only clocking at 1250mhz, but then came here and sorted that prob..... (Sperad spectrum then adjusted the FSB to 166mhz ) then after that, when i go to boot up i got.... "no device connected to the Fasttrack controller...bios not installed" then browing through the forum i found how to "solve" that problem... ( disabled the Serial ATA thing, dont know if thats right .... ) but now i dont get that "bios not installed" line any more.... all i get is a flashing line in the top left of my screen....
so to sum up....all i get now is.... that flashing line......what could be goin wrong?
Thanks in advance.....a very distressed...
//Simpo

This is an AMD board, so I will move your post to that forum.

IDE 3 with MSI KT4 Ultra

Hello!!
How do I get the Promise Controler Fast Track 376 on my Board to work?
I tried to connect both of my HDD´s (not at same time!!) but he will not recognice them!! After POST it says no drives detected, or Bios ist not installed (or something like that!!!)
I just need an explicit How To, because the tips and how to´s in other Boards haven´t worked!! I haven´t tried any Bios modifications or so!! The Mobo Bios ver. number is 1,4!!
I had no probs with that Highpoint Controller! What is so different with the Promise Controller!!
Sorry for my bad english! I am from Germany! .-)

Hello!!
The Raid Controller is enabled in BIOS
The Jumper Settings are correct (As displayed on HDD!)
The drives are working currently on IDE 1 without probs! (No PSU - 420 W - probs!!)
I can only try to use SATA to PATA Converter next!!?? or?
Thanks to everybody for helping me!!
Nobody

Problem with my MSI KT4 Ultra

Hi all!
I have a BIG problem, I have tried to look at this board, but there is many different answers out there ;(
I have KT4 Ultra with Athlon XP 2600+
I have set FSB to 166, and when I startup BIOS says Athlon XP 2600+.
But in windows system, it only says:
AMD Athlon XP2600+
2.09Ghz !!!!
768Mb RAM
Why is windows only says 2.09Ghz??
AND, I think my system is very slow. I used to have AMD 1200Mhz. And this sytem is almost like my last computer.
My System:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive

Quote
Originally posted by swedecom
Ok, I use these settings in my BIOS, are they right for my system??
MY SYSTEM:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive
MY SETTINGS IN BOIS:
Spread Spectrum = +- 0.25%
CPU FSB Clock = 166Mhz
CPU Ratio = Auto
CPU Vcore = (V) Auto
DDR Voltage (V) = Auto
Termination Vol (V) = Auto
AGP Voltage (V) = Auto
Hope someone can help me out

MSI KT4 ULTRA MAX VCORE

Is it possible for MSI to add higher Vcore settings with a BIOS update? The MSI KT4 ULTRA has a max Vcore of 1.85 which doesn't really help the overclockers much. If they could get the max Vcore to 2.00 that would be great for XP overclockers. )

I'm not complaining about my KT4 ULTRA. I think its a good board for people who aren't really into overclocking and performance tweaks, but I love to tweak the performance of my rig. I hate to say that other motherboard companies seem to get the picture, that they should make their boards as overclocking friendly as possible. ASUS, Abit, Epox etc. are considered the best because they have conquered into the overclocking market. I wish MSI would throw their hat in the same market because I personally feel they can.

PROBLEMS AGAIN, MSI KT4 ULTRA GIVE POOR STABILITY IN MY SYSTEM!!!

Hi, i get problems when overclock (fsb) my cpu with 133 fsb to 136 ONLY!!! , only support the overclock my cpu 1800(1533mhz)--to(1580mhz), high fsb 137 or high freeze , restart my system when run games or aplication with geforce 3 ddr 64mb, i modify vol agp to 1.8 , but get error again.
HELP ME!!!
I NEED NEW BIOS THAT STABILIZE MY SYSTEM!!!
System:
MSI KT4-ULTRA 6590-SR
CPU XP 1800+
256 DDR SANSUMG
T.VIDEO GEFORCE 3 DDR 64 detonator 41.09 agp4x
WINDOWS XP PRO SPK1
POWER 350 WATTS CODEGEN

Thanks for you help, but my power 350 watts codegen work a:
20A---3.3v
30a---5v
However i read guide revision 12-12-02 about psu and all configuration is correct !!!!!!
My powersupply not is problem
I NEED THAT MSI MAKE NEW BIOS FOR KT4-ULTRA!!
Thanks

Linux and MSI KT4 Ultra : DVD problems

Hi, I own an MSI KT4 Ultra Pure mobo. The vt8235 Southbridge is supported in the lastest version of the Linux Kernel, 2.4.20 . After upgrading the kernel all seems to work fine, but when the system try to initialize my hdc (Secondary master of IDE, a DVD reader DV-5800A from NEC) it locks up with the message :
hdc: device {Busy}
hdc: drive not ready for command
ide1: reset success!!
and start looping with this message.
What can I do to get work my DVD Reader? With my precedent MoBo it works perfectly
Thanks
Bye

Hmmm that error used to happen with an older kernel and an ALI chipset. If you leave it long enough does it give up trying and continue to boot? The ALI did this eventualy.

MSI Kt4 Ultra - Sound on Board

Hello, I have a problem with my onBoard sound.
Sry for my english, I am german.
I have a SB Live Volue soundcard and i want to install it, but when i deactivate the onBoard sound i cant't delete the drivers from it.
Pls, help, how can I deactivate the Sound-on-board, and install my other soundcard right ?
Pls, when someone is German here, write in german.
thx.

Yes, I disabled it in "Integrated Peripherals" the "Serial ATA Controller" and the "Audio Controller".
Is there someone more, I have to disable ?!
Or have I to deactivate it on the mainboard, too ?!
And how can I delete the drivers from Windows ?!
This drivers are:
Audiocodecs
Legacy-Audiotreiber
Mediensteuerungsgerät
Vidiocodecs
I have Windows XP and Win2k, because I use Partition Magic and Boot Magic.
MSI KT4-Ultra
Athlon XP 2000+
GeForce4 MX 440
256 DDR Samsung 333Mhz
SB Live 1024
Midi Tower 350 Watt

MSI KT4 ULTRA-BFISR + Ati Radeon 9700 pro = not good??

Hello everybody!
First of all, i youst have to say that i think MSI have the best motherboards....
Here's the problem (i haven't buyed anything yet!):
I am going to buy MSI KT4 ULTRA-BFISR and ATI Radeon 9700 Pro, but i have read many places that Radeon aint working with MSI KT4-based cards! Im am going to buy an 520W Power (i aint so good in english so i hope you now what i write :D )
I am also going to buy 2 x Cosair pc3500 xms ram... Is this one working with the motherboard by the way?
But my question is: Will the Ati Radeon 9700 pro work with this card? (i must remember to buy the 1.3 version!) I am gonna get my Radeon 9700 pro from USA, how can i now when i order that is an 1.3 card?
Thank you for answering! :]

I think also that even there is two drivers, that is not a reaseon why it isn't work. One time I install only standard VGA drivers, but result was that I got two standard VGA driver. 8o
First time I try without VIA drivers, then with 4.42 and 4.43 VIA drivers. Result was almost same all the time, it always crash when Nature test start, but this exist also to older mobo (Abit KT7A-RAID). Problem exits few games they lock up or stuttering. Ati demos works fine, but one time that car demo stuttering a lot, but I transfer data at same, so I'm not sure what was reason.
This moment I don't have possibilities to try Hyperion 4.45 drivers or something else, because it's my friend computer.
MSI KT4V 6712 (Bios 1.0)
AMD Athlon 1.2
512 MB DDR 333 RAM
SoundBlaster Live
ATI Radeon 9700 Pro (Club3D)
Power 300W
Realtek Ethernet card
Samsung 40GB harddrive
Samsung DVD
VIA 4.42 and 4.43
WIN98

MSI KT4 Ultra! A little question.

Hello. )
I'm very interested, in the new MSI KT4 Ultra, but i've a doubt:
The pure version of the KT4 Ultra, has a fan on the chipset?
How many IDE channels come with this pure version?
Thank you, and sorry about my poor english. :D

You can modify de FSB in the bios, but there is a jumper that provides these 3 options, 100mhz, 133mhz and 166mhz. 100mhz for the duron cpu's, 133mhz for the Athlon xp Palomino and Tbred, and 166mhz for the athlon xp Barton ( not 100% confirmed).

MSI KT4 ULTRA MS-6590

I have this motherboard: MSI KT4 ULTRA MS-6590 sempron and I have already bought the new CPU SEMPRON (AMD Sempron 2400+). I want to know if my motherboard is compatible with new CPU.
Thank you
Sorry for my English, but I'm Italian.

Hi
Not according to http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=356&kind=1

MSI KT4 Ultra-SR (MS-6590) And IDE3

Rig is As Follows:
MSI KT4 Ultra-SR (MS-6590)
AMD Athlon 1000Mhz :(
512MB DDR333 (PC2700) x1 stick
MSI GeoForce 4 Ti4200 8)
IDE1: Western Digital 40Gb 5400rpm (win xp pr) as master & Maxtor 80Gb 7200rpm as slave
IDE2: Liteon 52x24x52 CD-RW ) as master & Samsung 12x DVD as slave.
Soundblaster 5.1 Live PCI
350w Power Supply
MSI D-Bracket 2 & S-Breackets Fitted Also.
I have Three Questions.
>My CPU has a FSB of 200, but the bios (version that came with board) shows it as 100 FSB. See here for athlon bus speeds
Is it ok to increase the bus speed without damaging the processor.
>The two brackets that i have fitted (s and d brackets) do not work. Why?
>What are the optimal and settings for my ram (PC2700 512MB DDR) and GFX Card (MSI GF4 TI4200).
>Oh yeah, my CPU is now operating at a higher temp than before (using old K7VZA ECS Mobo) @ 50-55. Is this normal??
Sorry for the n00b questions, it's just that this is the first time iv ever taken my PC to pieces and re-configured it myself :P
Thanks in advance. -RjA

I can help a little 1000MHZ AMD chip=200FSB XP CPUs=266FSB this is CPU speed . AMD 1000MHZ CPU needs to run @100FSB where a XP CPU can run @133FSB This is MEMORY speed . Trying to crank that poor old chip up to anything other than 100 will do you NO good. You need to buy a bigger cpu of the XP kind. A lot of the older XPs can be had for a low price. 50c isn't not super hot. My KT4 runs in the 40s. You might want to think about a bigger cpu cooler to bring the temps down a bit. Most of your settings should be left at system default, since you only have a 1000MHZ CPU. When you go up to an XP then you can make a few changes. Regards BIGDADDY51 :D :D

Upgrading to a MSI kt4-ultra FISR board.....

Currently I've got a gigabyte motherboard and I want to upgrade to an: MSI kt4-ultra FISR board. Can I just pull my old board out and install the MSI board with all my old hardware, O/S already on harddrive - and do a start up, or will I run into errors and problems when I try this? Currently my system looks like this:
1) Case: "Xaser SC5000BWII" 400watt mid-tower case
2) Motherboard: Gigabyte GA-7DXR DDR+Raid
3) CPU Chip: AMD Athon XP 1800 1.6Ghz
4) Memory: 512 of PC2100 DDR266 Memory
5) AudioCard: Creative SoundBlaster Audigy MP3 card
6) VideoCard: ATI RADEON 9000pro, 128 DDR
7) Hard Drive: Maxtor 80GB 7200RPM ATA-133 "D740X" Mdl:6L080J4
8) Operating System: Ms Windows XP Pro
Thanks for the help........ seboyd ?( :D 8)

A clean install will give you 30 days to reactivate and it only takes a 5 minute call to get the new #s. Pretty simple and much easier than trying to straighten out all the error codes from old O S. I did however move an XP harddrive from a Turbo2 to a KT4 without a new install but they were both MSI boards. A clean install also gets rid of all the junk that accumulates. Just enter bios and make the CD rom 1 st boot . BIGDADDY51 CT. USA :D 8) :D

MSI KT4 Ultra-FISR

Recent upgrade problem
Old: MSI kt266 pro-2, allied 300w atx psu, ati radeon ve 32m
New: MSI kt4 ultra-fisr, allied 400w atx psu, MSI geforce4 mx440-vtp, western digital 80g hdd
Unchanged: 256m pc2700 ddr, top-g 24-10-40x cdrw, maxtor 45g hdd, sblive platinum
Problem: After upgrading I have difficulty installing software by cd. Errors are spomething like (bad cab file)
occasional but random reboots
moving files on hdd causes reboots
can someone help? I've contacted MSI about it and really hope I won't have to send the board in as defective if it really isn't.. thanks

Hi,
I have the same issues with my KT4 Ultra (pure version).
Running GF4 Ti4400, Athlon XP2400+ etc, 450W power etc. There are quite many posts of similar issues all over the Via Arena forums and some here as well. KT4 Ultra's and KT4V's seem to be the boards affected.
Installing the Via USB Filter Patch helped with narrowing down the number of crashes and some of the errors.
(note: disable automatic restart from 'Startup and Recovery settings' to see the driver that crashes)
Link to Via Arena FTP site
I had a K7T266pro2-RU board before this which worked 100% stable. I've tested all my components which are fine. Tested different power supplies, memory. Still, continuous random errors after many times of reinstalling Win2K by the book and with default bios settings.
Sometimes the setup works fine for a week and then starts to mess around again.
Looks like setting the cpu fsb down to 128 MHz from 133 MHz solves the issues, so try that and report back.
Also check the filter patch.
I'm personally waiting for the next bios release to fix these issues - if not, I'm showing this board RMA and go to nForce2 chipset.
I also tested the 1.25 beta bios, which gave me lots of crashes during Win2K boot -> flashed back to v1.10 and booting works again.
- Tom

Overclocking with MSI KT4 ULTRA

Similar Messages

Maybe you are looking for