Overlapping lan segments S2S tunnels (the other end)

Is there any way to policy nat incoming vpn S2S tunnel traffic?  I know we can policy nat out going to send traffic over a tunnel as something else...
e.g.
my firewall
LAN segment 192.168.10.0/24
1st external firewall with s2s tunnel #1 back to my firewall
LAN 10.10.10.0/24
2nd external firewall with s2s tunnel #2 back to my firewall
LAN 10.10.10.0/24
if no changes can be made to the 1st and 2nd external firewall meaning we cannot get to at leat
one of them so they policy nat out as another subnet....is there any thing we can do
on the "my firewall" ? (any incoming nat policy options or routes over the tunnel peer ip or something or the other???)
and this would be cisco asa's, all three at least.
thank you!

hi, i looked at the document and thank you for responding!  my scenario would be a little bit different though wherein we have another pix say "pix-C" which in the pdf would also be using 10.1.0.0/24
we couldn't make a 2nd policy nat for pix-C.  we couldnt have a 2nd source and destination ACL used for a 2nd policy map as the pix A would not know which access-list to use...
i know another option is public ip to public ip's for the site to site but that isnt always an option.
So going by the pdf you attached what if there was also a pix-C that is also using 10.1.0.0/24 and we cannot make configuration changes on pix-B or pix-C just only on pix-A  ...is there anyway we can have the two site to sites A to B and A to C even though B and C both have 10.1.0.0/24 ?

Similar Messages

  • I have a 2005 Jaguar xj8.  When I tried to upgrade my 3gs to a 4g I got a ticking noise in the speaker and no one on the other end could hear me.  I had to go back to a 3gs.  My phone is shot and I need to upgrade.  Has there been a fix to the problem?

    I have a 2005 Jaguar xj8.  When I tried to upgrade my 3gs to a 4g  two years ago, I got a ticking noise in the speaker and no one on the other end could hear me.  I had to go back to a 3gs.  My phone is shot and I need to upgrade.  Has there been a fix to the problem?  Apple told me there was some sort of interference with the airbag system.  Jaguar was totally unhelpful.

    Hi Labjock,
    Welcome to the Support Communities!
    The article below may be able to help you with this. 
    iPhone: Microphone issues
    http://support.apple.com/kb/ts5183
    Cheers,
    - Judy

  • Hi, i am having an issue with a basic motion scroll effect.  I already watched and read every tutorial out there regarding this topic and even tried the adobe chat support, but the guy on the other end of the line disconnected me-, probably he didn't unde

    Hi, i am having an issue with a basic motion scroll effect.
    I already watched and read every tutorial out there regarding this topic and even tried the adobe chat support, but the guy on the other end of the line disconnected me…, probably he didn't understand what i wanted from him because english is not my native language, so a will try to be very, very clear about this one..
    please note, that i am new to muse, this is my first project ever.
    my idea is as following:
    when the customer comes to our companies site, he just sees our logo on a white Background. the logo consists of, say, four elements. when the customer scrolls down, the logo starts to disassamble: first the first part of the logo flies out the left side of the site, then the second part of the logo vanishes down, then the third part of the logo flies to the right, then the fourth part of the logo flies to the top and out of the customers view. given what i have seen, it is possible to do that….
    so…..
    now i have the four parts of my logo imported as png files into muse and assembled them in design view to build our companies logo. I select every one of the four parts and go into the scroll effects tab left beside the layers tab. first i enter the same values for every one of the four parts: initial motion: 0x and 0x again for the left and right motion; key position ( t-handle) : 0px; final motion: 0x and 0x again for the left and right value.
    now i hit "preview".: the logo is "pinned" at the correct position, i can scroll but the logo stays where it is. so far so good….
    now i select all the four elements again and go to the scroll effecs tab. at "final motion", i click the down arrows and enter 1x. I hit Preview…
    when i am scrolling down the WHOLE logo goes down…. so far so good.
    NOW i want the first part of the logo to go down, THEN the second part to go left, THEN the third part to go up, THEN the fourth part to go right.
    so i select ONLY the first part, go to the scroll motion tab, at "final motion" i click the left arrows, then i enter 1x.( the up-down value, i set to 0 again).. i hit Preview…
    the first part of the logo goes left as soon as i start scrolling, the other three parts still go down at the same time…
    NOW i want the second part of the logo to start moving, when the first part has left the scene, not at the same time as the first part.
    SO I SELECT THE SECOND PART AND DRAG ITS T-HANDLE (KEY POSITION) DOWN TO, LETS SAY, 200PX. SO IT STARTS MOVING ONLY AFTER THE CUSTOMER HAS REACHED THAT POINT, RIGHT?
    BUT WHEN I PREVIEW THAT ****, THE LOGO IS NOT TOGETHER ANYMORE, THE SECOND PART IS FLOATING ANYWHERE ELSE BUT WHERE IT SHOULD BE…..WTFF????
    short: when i move the t handle, the initial position of the object changes. thats what i said to the adobe employee, but he said, that thats the expected behavior….
    but if thats so, how can i have my four parts correctly together, so they form my logo, but with different t handles, so that they all start to move at different times??
    Pleeease help me, i am dying of frustration here…..:( that behavior cant be right, right?
    Thanks so much to everyone who actually reads this post and tries to help…….
    All the best,
    Niki Lapan

    Thank you so much for helping,
    But i really wonder how you did that. did you always switch between design view and preview view, then change the key position for 2px then switch back, to align the four letters? because i imagine that can get really frustrating, if you have a logo consisting of 58 parts instead of 4!:)
    Anyway thank you very much for your time and effort!!!!

  • Printing to a Imagesetter (Platemaker) from PageMaker 6.5 on Windows 7 OS I get a message from the platesetter there is no process on the other end of the Pipe Any Ideas

    I am running PageMaker 6.5 on a Windows 7 OS. I can print to all my printers except one. It is a Platesetter or sometimes called an imageseter.  When I send a file to it, it gives me the message "No Process On The Other End Of The Pipe".  I have installed and downloaded all PPD's and such and installed them the same as they were previously installed on a Windows XP PC when it worked great. Any ideas?

    Go back to XP. PM has been for more than 10 years and is unsupported under XP. In fact, 6.5 has support only for Windows 2000 and earlier.

  • IPhone 5 call quality issue. (Either call ends or very choppy on the other end)

    At random times my calls don't go through. The phone says call ended and doesn't ring. The reception is either full or close to full. This has occurred numerous times while calling different numbers. If I do manage to get the phone to ring, the person on the other end wouldn't be able to hear me as it would be very choppy. I have tried to reset the network settings with no luck. It is a random thing that happens at random times. It is not the carrier issue as all other functions of the phone work. Also this phone is an unlocked unit from Apple and is not in the U.S.

    I just replied to a similar post and I'll copy and paste my response here. I was having the same exact issue. Here is my possible fix.
    Yesterday I updated the OS to the latest release. Then right after that I called AT&T and they reset my sim card. Or something like that. They did some sort of reset.
    I then got in my car and drove around to test the phone. Because that is when the problem is worse. FINALLY they claim to be able to hear me clearly!!!!
    I think it was the combination of both the OS update and the sim card reset that fixed it. Hopefully..... It has only been one day but so far so good. I'll update this post if things change.
    Try this and let us know if this works for you.

  • When I make a call, I can hear the person on the other end but they can't hear me. It's not the mic, I use the voice recorder all the time and I have no problems w FaceTime. My headphones and Bluetooth do the same thing as far as not being able to be hea

    When I make a call, I can hear the person on the other end but they can't hear me. It's not the mic bc face time or voice recorder are not affected. I can't even use my headphones or Bluetooth to get around the problem. This has stumped 2 geniuses, they just try to swap it out for $150.

    I am having the same issue with my iPhone 4. I can hear everyone but they can't hear me. Visited Apple Store and they said speakers were out, both bottom mic and top one for speaker phone. Said they were busted. Reloaded all software and didn't work. Got in parking lot and worked for 1 call. Now it's out again. Wanted $150 for new phone, haven't done it yet. don't know what to do.

  • I have a iPhone 4 and all of a sudden when I answer a phone call the person on the other end can't hear me ???? I can hear them , so I've had to put it on speaker for all my calls - ? Any tips on how to get it back to being able to speak normally

    I have a iPhone 4 and all of a sudden when I answer a phone call the person on the other end can't hear me ???? I can hear them , so I've had to put it on speaker for all my calls - ? Any tips on how to get it back to being able to speak normally

    Morning Lupoipia,
    Thanks for using Apple Support Communities.
    If you can't be heard by someone who is calling, take a look at this article:
    iPhone: Can't hear through the receiver or speakers
    http://support.apple.com/kb/TS1630
    Best of luck,
    Mario

  • I frequently lose audio when in the middle of a call.  I am not certain whether it is a full disconnect or just an audio loss.  The person on the other end reports still being able to hear me, however, I suppose they could hear me speaking over another s

    I frequently lose audio when in the middle of a call.  I am not certain whether it is a full disconnect or just an audio loss.  The person on the other end reports still being able to hear me, however, I suppose they could hear me speaking over another source even if bluetooth disconnected. The loss of audio is always preceded by a quick shrill noise, so I can easily tell when it happens.  All I have to do to fix the problem is to select Audio Source on the call screen, temporarily switch audio back to the iPhone, and then switch back to the headset, and then it starts working again.
    My Iphone5 was replaced and having same Problem. Only does this when using bluetooth for talking.

    I have the exact same issue... I've been using a Jabra Extreme2 and just this weekend, bought a Plantronics Marque2 and today had the same issue, so it's clearly not the headset but the phone or OS.
    I might try a restore and see if it helps...

  • I just bought an Apple TV and i have a bose sounddock with a mini jack in the back and and optical cord with a mini adapter on it (so optical cord going into the Apple TV and the mini adapter on the other end going into my bose dock but i dont get sound??

    I just bought an Apple TV and i have a bose sounddock with a mini jack in the back and and optical cord with a mini adapter on it (so optical cord going into the Apple TV and the mini adapter on the other end going into my bose dock but i dont get sound?

    Not all the sound docks accept both analogue and optical on the auxillary input - I don't think the portable ones does but may be wrong - check the user manual.
    As I said earlier all the mini optical (min Toslink) adapter does it make the optical connector fit a smaller socket, it does not convert digital audio to analogue for an analogue only auxillary input.
    AC

  • Can I use an AE as a Bridge allowing me to hardwire my iMac and offer a wifi to my MacBook? The Ethernet in my office is hard wired but does come in from a router on the other end of the building that has a wifi that cant reach my office...

    Can I use an AE as a Bridge allowing me to hardwire my iMac and offer a wifi to my MacBook? The Ethernet in my office is hard wired but does come in from a router on the other end of the building that has a wifi that cant reach my office...

    Thanks, I thought so but wanted to be sure before running out and buying one...  I also called Apple Joint Venture and they helped me set it up without the Airport by using my iMac as the wifi!  Thanks again!

  • Speed dial only has one icon, to open up the windows. Another used to be on the other end of the tool bar for entering websites into the windows. Also do not know how to form another group.

    I have just downloaded Firefox into a new computer. The firefox I had in my old computer had one (9 pt) icon at one end that brought up the speed 9 speed dial windows. It also had another similar icon at the other end of the tool bar that you could click on and place a website you were looking at into a particular window. This add on does not have that feature, which makes it very hard to make entries into the windows.
    Also I have not found the way to add other groups of windows as I had before. I could even label them in categories. What to do?
    My Computer is an HP p6653w and my default browser is Firefox 3.6
    My operating system is windows 7.

    Hi,http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03149924&cc=uk&dlc=en&lc=en#N89
    First, I am sorry to see your experience, however be aware that this forum is a peer-to-peer community and not a direct contact with HP.
    To clarify, the product specification do list the ink cartridges regionalization, the specifications itself reffer to HP Suresupply to locate the ink cartridges for your region, as well as the following document which clearly state that information:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03239171&tmp_task=prodinfoCategory&cc=uk&dlc=en...
    Firs be sure to have the latest software installed prior contacting HP support, which should be listed as 28
    You may find that information listed in the following document (Check the How can I tell which driver version I have? section), if you have any older version be sure to uninstall it and install the latest software, as listed within the same document:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03149924&cc=uk&dlc=en&lc=en#N89
    If you need, the latest software can be found below:
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-108821-3&cc=uk&dlc=en&lc=en...
    Next ensure you have any of the 564 ink cartridges, once the printer being reset it require all the 4 ink cartridges to work
    Finally check the private messages I sent you prior contacting HP support , the envelope icon at the top-right part of that screen.
    The ensure you use the correct contact details lease double chekc it below:
    http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
    Regards,
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • How can I play my ipod classic 30G thru my older home stereo? Radio Shack guy sold me a head phone adapter to use in the head phone socket on the stereo with the other end attaching to the ipod. It doesn't do anything. Are there settings I need to make on

    How can I play my ipod classic 30 G thru my home stereo system? The guy at Radio Shack sold me an adapter for the older, larger headphone adapter on my stereo receiver with an ipod attachment on the other end. It doesn't work. Do I need to make special settings on the ipod? Should it work? I read elsewhere that I need a Y connector.  Thanks for any help.

    The headphone jak on your stereo is an output, not an input.  You cannot route music into your stereo throughthe headphone jack.
    You can get a cable that connect from the headphone output of the ipod to the stereo inputs on your stereo:
    http://www.amazon.com/gp/product/B000V0G2C4/ref=pd_lpo_k2_dp_sr_1?pf_rd_p=486539 851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B000YK1JAG&pf_rd_m=ATVPDKIKX0DE R&pf_rd_r=0MQ2G1EDXDZ3DYEW327X

  • MMS showing up on the other end as question marks?

    MMS is working almost perfectly for me, but there have been a few instances where it has screwed up a little.
    The same problem has occurred a few times now, but there have been a few images I tried to send to a friend that showed as 'Sent' on my iPhone, but my friend told me these images were showing up as question marks.
    He describes it as "a teeny tiny picture of a hill with a piece of paper on the top of it, and a question mark".
    This has happened, as I said, with a few different pictures, on a few different occasions.
    The pictures finally were able to go through after I took a screencap of them, and sent him the screencap. This is the part I find strange. Is it possible that hyphens in the filename might be screwing up the delivery of these images? I find it so strange that I try sending the same picture three times, and all three times it shows up as that strange question mark picture, but when I send a screencap, it goes through just fine.
    Another friend of mine said that a picture he sent to someone also showed up as a question mark on the other end.
    Anyone else experiencing this? Anyone know what the problem could be?

    Anyone?

  • Since I've done the update ios6 on my ipad2 when I FaceTime the person on the other end says all they hear is static. Anyone know how to fix this?

    Since I've done the ios6 update on my ipad2, when I FaceTime someone the person on the other end says all they hear is static and my voice very faintly. Anyone know how to fix this? Thank you.

    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems
    http://tinyurl.com/32drz3d
    I saw one post where a user said dust got inside the small microphone hole. Using a vacuum cleaner removed the dust and restored the audio.
     Cheers, Tom

  • TS3276 When I reply to an e-mail it comes out blank the other end?

    I do not have problems sending e-mails but when I reply to an e-mail it sends but comes out blank the other end?

    '''re: Forwarding'''
    You have the option to forward the received email 'inline' or as an 'attachment'.
    This can be set up here:
    'Tools' > 'Options' > 'Composition' > 'General' tab
    This is because you are not responding to a specific email - you are selecting to forward information from a different person to another person, which may be best sent as an attachment.
    '''re: Reply'''
    In this instance you have the option to either:
    * include the received email in a reply
    * Not include the received email in a reply
    * include selected part (quote) of received email in reply.
    A Reply implies a continued conversation and so the option to include the conversation is available.
    This is set up here:
    'Tools' > 'Account Settings' > 'Composition & Addressing' for the mail account.
    But regardless of whether you choose to 'automatically quote the original message when replying' or not, you can always highlight a section of text and then click on 'Reply' to include only the selected section of text.
    A Reply will also not include any attachments that were received attached to the original email because you do not need to send back the senders own attachments.
    Otherwise you create a new 'Write' message and attach the original email, so it is not technically a Reply - you do not use the 'Reply' button and these emails will not be threaded. It makes it more difficult to see continuity of conversation.

Maybe you are looking for