Overmodulated Output Audio on "Client Monitor"

I have been using an old Sony SD monitor to playback for clients. The video and audio go out of FCP to my JVC BRHD50 via Firewire then to the montior with SVHS for video and RCA for audio through a Makey Mixer to powered speakers, no problems.
Now, I upgrade to a Sony Bravia HD monitor. Video is fine, audio seems hugely overmodulated, just a garble. This is the case whether I route it as before or just try to use the built in speakers to the monitor. I found this previous discussion but am not sure if it applies and why I would suddenly have this issue:
Speaker hum from Rokit 5s when external video monitor is plugged
Posted on: Aug 2, 2008 5:33 PM, by user: seanmcp33 -- Relevance: 25%
If I switch audio to playbach through the Kona instead of the Firewire it is clear but out of sync. Thanks.

I would check to see if they're any menus on the Bravia that deal with audio input. Sounds like you may need some sort of "attenuation (if that's the right term)" to make it work without adjusting something on the monitor.

Similar Messages

Output audio different than video

From FCP, timeline highlighted, I exported to Compressor. 30 minutes of video and corresponding audio. When it's finished the video is what was in the timeline in FCP, but the audio is from another clip altogether.
I've tried the same steps with other video/audio in the timeline. Same thing. The outputted audio is ALWAYS from the same (different) clip. Compressor version 1.2.1.
The compressed audio is from the first batch of footage I captured for this project. Every time I try and compress something in the timeline the audio is always from this clip.
Any thoughts/suggestions?
thanks!

Hi. I'm running STP 2.0.2 with 5.1 audio through an RME Fireface 400 and sending the video via HDMI from a Black Magic Intensity card to an LCD TV. If I can refer you to page 318 of the manual it states that "When you use a video output device that supports both video and audio output, Soundtrack Pro automatically routes your audio output to this device to provide the best possible synchronization of the audio and video". Therefore not a bug, but a default built into STP.
I'm sure they are correct, but cannot see why this was not added as a preference option. My solution has been to run the LCD TV as a second monitor through it's PC input, which works fine but does not give HD image. I have tried many options (All combos of available audio preferences for system and STP) without success. My next plan is to cut the HDMI cable and disable the audio if possible, but this may not work due to the nature of HDMI (System may believe the HDMI output is an audio capable video device even though audio path has been severed).

DVDSP output to my NTSC Monitor?

Hey there,
I have a JVC NTSC monitor that is plugged into my AJA Kona LH. I'm having great luck using it with Motion, FCP and After Effects, as the "Output" preferences allow me to choose the Kona and my work shows up on the JVC just like it's supposed to.
Somehow, however, I do not get any option in Preferences within DVD studio pro to output to anything other than the Desktop. I have no Firewire into the JVC, which I think may be part of the issue?
Any ideas how I can do DVD simulations and output them onto my monitor?
Thanks!
Gman

Any ideas how I can do DVD simulations and output them onto my monitor?
Can't be done with Apple's new Desktop Preview thingie... it specifically requires a video card to do it, not an AJA card. It certainly does not show my Aurora Fuse card as an option.
It's not a Firewire issue. With Firewire, you have something (usually a camcorder or DV deck) that serves as the digital/analog converter. If there was a Firewire converter that decoded MPEG2 instead of DV, and if DVDSP supported it, then it would be a Firewire issue.
Basically, to do what you want, you'd need a card that provided hardware MPEG2 decoding. Apple bought Spruce's card that provided that capability when they bought Spruce, but have chosen not to offer it as a product.
The lack of true MPEG2 decoding and previewing on a broadcast monitor is often mentioned as one of the big drawbacks for using a Mac as a pro DVD authoring setup.

Hello to all: My iMac has developed a video display problem. It displays everything in cartoon like colors - purple, green, blue. Can this be repaired? Is there a way to output to a different monitor? Thanks in advance! isplays

Hello -
My iMac has developed a video display problem. Everything now appears in a strange, cartoonish way. Purples, greens, blues. Can this be fixed, and if so, any idea how much it might cost? Also, could I output to a seperate monitor? I plan to replace the unit , but cannot right now. Thanks!

Go to System Preferences > Universal Access > Seeing.
In the Display area, reset it to "Black on white" by clicking that checkbox.
You can also reset it by pressing Command-Option-Control-8

IPhone 4 Won't Output Audio, No Airplay

My iPhone4 (OS 7.1.2) works fine, but has essentially become a brick to external devices. Music will not play through headphones, the phone no longer outputs audio to my car stereo via USB or Bluetooth, and the AirPlay icon has disappeared from the video player (yes, my Apple TV is on the same wi-fi connection). In my car, the USB screen says "Unreadable" and the Bluetooth screen doesn't even acknowledge my phone (which is discoverable).
All of this started happening under curious circumstances. Up until a few weeks ago, my phone's loudspeaker hadn't been working for a while. The ringtone worked, but no other audio worked. It was like the phone thought I had headphones plugged in. All of a sudden, the loudspeaker started working--I have no idea why--and at that time, I started experiencing the problem I'm describing here.
They sure seem related. Any tips from the community?

Okay - other things I would try is different USB cables and restoring on another computer if possible.
If no joy with either of those, make an appointment at an Apple store near you and bring it in to be evaluated. It may have a hardware problem and will need to be replaced.
~Lyssa

Macbook Pro 15-inch (Retina Display) HDMI doesn't output audio to TV

My rMBP's HDMI port doesn't output audio through the HDMI cable to my TV. Instead, the audio plays on the laptop's speakers. I know the problem is not the HDMI cable nor the TV because my TV speakers play sound when I connect my Windows laptop via the same HDMI cable and TV jack.
Anybody know a fix?

I have this exact same problem, I have gone to preferences, ans selected the output as HDMI and nothing happened. Later I went to Utilities, Audio MIDI Setup and tried to select different options to get the sound working and nothing, the volume for the HDMI was grey, disactivated, all the time. Any new findings lately? I have my computer fully updated.

How do I make my Mac not use the external mic on my Apple Earphones but output audio through the earphones?

I want to use the microphone built in to the MacBook Pro while still outputting audio through the Apple Earphones. This is because the microphone on my earphones has stopped working. If anyone knows how to do this, please tell me

Based on the info you provided, is this your printer?
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=219&lc=en&cc=us&dlc=en&sw _lang=&product=5058336#N187
If so, it appears the do have a driver available for Lion.

Create report output to the Client of the Application Server inst.of Server

Hi,
Please suggest the soution for the below:
We are using SET_REPORT_OBJECT_PROPERTY and WEB.SHOW_DOCUMENT to create report. Now Requirement is to save the report output to Client instead of server. I tried to use WEBUTIL but web util can be used from form only becuase that is using form item.
(1) We are calling all our report from a form. Is there any option to trigger a action when ever a report job is created in Application server (report server)
(2) Please let me now is there any option to create the output directly to client of application server 10G R1WIN , 10GR2WIN or in 11G. If yes please let me know the details.
Wtih Thanks & Regards
K.Sundar
Edited by: 870860 on Jul 13, 2011 10:27 PM

Hi,
Please suggest the soution for the below:
We are using SET_REPORT_OBJECT_PROPERTY and WEB.SHOW_DOCUMENT to create report. Now Requirement is to save the report output to Client instead of server. I tried to use WEBUTIL but web util can be used from form only becuase that is using form item.
(1) We are calling all our report from a form. Is there any option to trigger a action when ever a report job is created in Application server (report server)
(2) Please let me now is there any option to create the output directly to client of application server 10G R1WIN , 10GR2WIN or in 11G. If yes please let me know the details.
Wtih Thanks & Regards
K.Sundar
Edited by: 870860 on Jul 13, 2011 10:27 PM

Exception writing binary data to the output stream to client -Broken pipe

Hi,
I am trying to use the drag & drop feature using Contributor mode of Webcenter sites. Single Image Page Attribute is working properly where as Multiple Image Page Attribute throws the following error:
[ERROR] [.kernel.Default (self-tuning)'] [logging.cs.satellite.request] Exception writing binary data to the output stream to client 10.191.117.106
java.net.SocketException: Broken pipe
     at java.net.SocketOutputStream.socketWrite0(Native Method)
     at java.net.SocketOutputStream.socketWrite(SocketOutputStream.java:92)
     at java.net.SocketOutputStream.write(SocketOutputStream.java:136)
     at weblogic.servlet.internal.ChunkOutput.writeChunkTransfer(ChunkOutput.java:568)
     at weblogic.servlet.internal.ChunkOutput.writeChunks(ChunkOutput.java:539)
     at weblogic.servlet.internal.ChunkOutput.flush(ChunkOutput.java:427)
     at weblogic.servlet.internal.ChunkOutput$2.checkForFlush(ChunkOutput.java:648)
     at weblogic.servlet.internal.ChunkOutput.write(ChunkOutput.java:333)
     at weblogic.servlet.internal.ChunkOutputWrapper.write(ChunkOutputWrapper.java:148)
     at weblogic.servlet.internal.ServletOutputStreamImpl.write(ServletOutputStreamImpl.java:148)
     at COM.FutureTense.Servlet.ServletRequest$OutputOutputStream.write(ServletRequest.java:80)
     at COM.FutureTense.Servlet.ServletRequest.write(ServletRequest.java:1633)
     at com.openmarket.Satellite.RequestContext.write(RequestContext.java:1123)
     at com.openmarket.Satellite.BytePiece.stream(DataPiece.java:253)
     at com.openmarket.Satellite.CacheObjectImpl.stream(CacheObjectImpl.java:651)
     at com.openmarket.Satellite.Http11Responder.respondForWrapper(Http11Responder.java:142)
     at com.openmarket.Satellite.WrapperAwareResponder.respond(WrapperAwareResponder.java:36)
     at com.openmarket.Satellite.SatelliteServer.execute(SatelliteServer.java:85)
     at com.openmarket.Satellite.servlet.BaseServlet.doGet(BaseServlet.java:118)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:707)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
     at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
     at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
     at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:301)
     at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
     at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
     at com.fatwire.wem.sso.cas.filter.CASFilter.doFilter(CASFilter.java:557)
     at com.fatwire.wem.sso.SSOFilter.doFilter(SSOFilter.java:51)
     at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
     at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.wrapRun(WebAppServletContext.java:3730)
     at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3696)
     at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
     at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:120)
     at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2273)
     at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2179)
     at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1490)
     at weblogic.work.ExecuteThread.execute(ExecuteThread.java:256)
     at weblogic.work.ExecuteThread.run(ExecuteThread.java:221)
Thanks
KarthiK

Thank u very much,
     FileOutputStream opGif = new FileOutputStream(destFile, false);
I have changed above line with the following line:
     PrintWriter opGif = new PrintWriter ( new FileWriter(destFile, false));
and now this code is working very fine.
Thanks once again...

How do I add an output for a 2nd monitor?

I have a mac mini that was purchased in 2009 I believe, maybe 2008. The operating system has been upgraded to Snow Leopard. I want to add a 2nd monitor, so I can use 2 at the same time, however, there is only one output. Is there a way to add an output for a 2nd monitor? OS is 10.6.X. not at the computer right now to check.
Thanks for input.

If the back of your mini looks like this:
- then you have two display ports already (Mini DVI Port and MiniDisplayPort). I only mention this, as it may not be obvious! You just need the right adapters to feed your two monitors.
If it looks like this:
- then you do indeed only have one display output (DVI) and then ignore me, and listen to Asatoran!

Veiwing HD on a client monitor Aja card has no HDMI or DVI . any solutions

I wrote to aja and they said to use the analog component out. I want to use the HDTV to on-line hd shows. Does going analog out sound like I'm not getting the best to the monitor? Do I need to add another DVI card to the computer? Will it work with the AJA Lhe?

Well, you have the LHe, right? That doesn't have HDMI out...so you can't use that. It has SDI out, but, the HDTV doesn't. So that leaves Component. They are right (as usual). Component gives a fine signal, I use it myself at times.
DVI out from your computer will NOT give you anything resembling a proper video signal to the HDTV. With the LHe, the only option you have is Component. And it will get you a decent signal.
ONLINE HD shows? Well, since you can't properly calibrate the HDTV to color bars, I'd be hard pressed to recommend this option. Fine for client monitoring, but for critical viewing? Nope. The Matrox MXO2 has HDMI out that will calibrate your HDTV...I'd trust that. But HDTVs don't have the professional level options build in.
Shane

Outputting audio from Mac

What is the difference between using the Mini Displayport to Output audio (such as multi-channel audio) vs. using the optical out (headphone jack) via a TOSlink/Digital Optical cable to an external sound system?

MIDI is NOT audio, you cannot transport audio over MIDI cables.
So, does the Yamaha have audio inputs?

Airport Client Monitor for Intel

It appears that the ever-useful Airport Client Monitor does not work on Intel Macs. Am I wrong - is there a universal version?
I've just found a donationware utility "AP Grapher" that may be a useful substitute available here:
http://www.chimoosoft.com/products/apgrapher/
I've been testing for a day so far. It looks good - I think a donation is deserved. I've only glanced at the "stumbler" function, but that looks good too.
From the Macreviewcast
"AP Grapher is a freeware tool for plotting the strength of a network as a function of time. AP Grapher has received a recent (Dec 06) update to Universal Binary along with some performance enhancements. It now does all the stuff that the Airport Client Monitor does as well as what MacStumbler does in one tool. The most valuable part is the time domain plot of Airport link characteristics. The plot will record data for as much as half an hour."

this would appear to the the problem.
Actually, NONE of the older tools that report on wireless networks or status work anymore.
iStumbler has been fixed. I imagine that the rest will get fixed in time.
- gws

Macbook OS X Yosemite - Logitech headset output audio not working with Rosetta Stone

So I got my macbook air 2014 with Yosemite software and I installed Rosetta Stone and I couldn't get the Logitech Headset (H540) to get the output audio through it. The software will accept the microphone audio, but it will send the output audio throughout the internal speakers of my macbook air, or even worse, it will freeze the program until I disconnected the headset (as soon as I unplugged it from the usb, the software will continue like a nothing was going on).
So I look in dozens of webpages trying to find a solution, but I there was none. I read that for some people creating a "multi-output device" in audio midi resolved the issue, but for most people including myself, it didn't work.
So after trying different options in the Audio MIDI setups, I found the solution!! : If you change the "format" from the default 16000.00 Hz to one higher, it will work like a charm! Now everything is working perfectly for me, including the main reason of this research: Rosetta Stone program.
I hope this post helps and saves a lot of time to any of you having this same problem.
If any other questions (or thanks ) reply to this post.

This is great! I've got one follow-on problem to this, though: My format rate seems to keep snapping back to 16000, and breaking until I go back and fix it again (32000 works fine for me). Any idea how to twiddle things so that 32000 is the default for my device?

"The source and output audio channels are not compatible or a conversion does not exist" - ?

I'm trying to export from Premiere Pro for a f4v file that matches all source settings except resizing the video. I've done this a million times but today, when I hit EXPORT, I'm getting an error message from Adobe Media Encoder that says "the source and output audio channels are not compatible or a conversion does not exist." I'm using wav, mov and mts files in my audio tracks and everything plays happily in the timeline. Any ideas?
Thanks for any help!

Sounds like you unsuccessfully trying to output a 5.1 Master to a stereo or mono file. Or something along those lines.

Overmodulated Output Audio on "Client Monitor"

Similar Messages

Maybe you are looking for