OVI map problem with E52

Hi,
Iv been using E52 for the past 11 months and loved the way OVI maps worked but about 2 months back i had some serious problem related to keypad and since the customer care couldn't fix it they replaced it with a new E52. I am not able to use OVI Maps properly on this new E52 meaning my current location is being shown and also in the search option I am able to search for places but when I am selecting the location and opting for drive to or walk to option then the waiting for GPS option keeps me waiting forever. With my previous E52 this problem never exsisted and the route map was created immidiately. I dont mind using the map service over the GPRS instead of GPS. I have updated the firmware and also installed the latest nokia OVI map software, updated the maps but still facing the problem.
Please Advise.

@Manish4ever
Welcome to the forum!
I am assuming that you will have the same functions as on my E72 a similar S60 3rd FP2 device.
Suggest that you go to Menu > Ctrl. panel > Settings > General > scroll down list to "Positioning" > Positioning methods - temporarily disable ALL except Integrated GPS, go outside away from tall buildings if feasible, open OVI Maps application and wait 20 -30 minutes necessary for it to establish very first positional lock.
Happy to have helped forum with a Support Ratio = 42.5

Similar Messages

Ovi maps problems with Nokia 5800 xpress music

Since Ovi updated the maps I've had trouble using it. I have version 40 firmware which was installed by Vodafone when my device expired. Despite the update, Ovi maps just crashes the phone when I try to use it. The screen goes blank and I get all coloured lines flashing down one side and the phone reluctantly restarts. Any advice please?

I am having exactly the same problem with my 5800 xpress music having updated to version 40.0.005.235.10 and installed the new version of OVI maps and the software Own Voice.
I have also tried reinstalling the sotware, restoring my phone to factory settings and resetting my phone by pressing the green, red and camera button whilst powering up. The problem persists. I will be making a call and within a few seconds of the call being connected the phone switches off and back on again. I also get the the coloured lines flasing on the screen.
Please Nokia Support, help us out.

Mapping problem with compressed key update record

Hi, could you please advise?
I'm getting the following problem:
About a week ago replicat abened with "Error in mapping" error. I found in discard file some record looking like:
filed1 = NULL
field2 =
field3 =
field4 =
field5 =
datefield = -04-09 00:00:00
field6 =
field8 =
field9 = NULL
field10 =
Where filed9 = @GETENV("GGHEADER", "COMMITTIMESTAM"), field10 = = @GETENV("GGHEADER", "COMMITTIMESTAM"), others are table fields mapped by USEDEFAULTS
So I got Mapping problem with compressed key update record at 2012-06-01 15:44
I guess I need to mention that extract failed in 5 minuts before it with: VAM function VAMRead returned unexpected result: error 600 - VAM Client Report <[CFileInfo::Read] Timeout expired after 10 retries with 1000 ms delay, waiting to read transaction log or backup files. To increase the number of retries, use SETENV (GGS_CacheRetryCount = n) in Extract parameter file. To control retry delay time, use SETENV (GGS_CacheRetryDelay = n). handle: 0000000000000398 ReadFile GetLastError:997 Wait GetLastError:997>.
I don't know if it has ther same source as data corruption, could you tell me if it is?
Well, I created new extract, starting 2012-06-01 15:30 to check if there was something with extract at the time, but got the same error.
If I run extract beging at 15:52 it starts and works.
But well, I got another one today. Data didn't look that bad, but yet one column came with null value:( And I'm using it as a key column, so I got Mapping problem with compressed key update record again:(
I'm replicating from SQL Server 2008 to Oracle 11g.
I'm actually using NOCOMPRESSUPDATES in Extract.
CDC is enabled for all tables replicated. The only thing is that it is enabled not by ADD TRANDATA command, but by SQL Server sys.sp_cdc_enable_table, does it matter?
Could you please advise why does it happen?

Well, the problem begins somewhere in extract or before extract, may be in transaction log, I don't know:(
Here are extract parameters:
EXTRACT ETCHECK
TRANLOGOPTIONS MANAGESECONDARYTRUNCATIONPOINT
SOURCEDB TEST, USERID **, PASSWORD *****
exttrail ./dirdat/ec
NOCOMPRESSUPDATES
NOCOMPRESSDELETES
TABLE tst.table1, COLS (field1, field2, field3, field4, field5, field6, field7, field8 );
TABLE tst.table2, COLS (field1, field2, field3, field4 );
Data pump:
EXTRACT DTCHECK
SOURCEDB TEST, USERID **, PASSWORD *****
RMTHOST ***, MGRPORT 7809
RMTTRAIL ./dirdat/dc
TABLE tst.table1;
TABLE tst.table2;
Replicat:
REPLICAT rtcheck
USERID tst, PASSWORD ***
DISCARDFILE ./dirrpt/rtcheck.txt, PURGE
SOURCEDEFS ./dirdef/sourcei.def
HANDLECOLLISIONS
UPDATEDELETES
MAP tst.table1, t.table1, COLMAP (USEDEFAULTS , filed9 = @GETENV("GGHEADER", "COMMITTIMESTAMP"), filed10= @CASE(@GETENV("GGHEADER", "OPTYPE"), "SQL COMPUPDATE", "U", "PK UPDATE", "U",@GETENV("GGHEADER", "OPTYPE")) ), KEYCOLS (field3);
MAP dbo.TPROCPERIODCONFIRMSTAV, TARGET R_019_000001.TPROCPERIODCONFIRMSTAV, COLMAP (USEDEFAULTS , field5 = @GETENV("GGHEADER", "COMMITTIMESTAMP"), filed6= @CASE(@GETENV("GGHEADER", "OPTYPE"), "SQL COMPUPDATE", "U", "PK UPDATE", "U",@GETENV("GGHEADER", "OPTYPE")) ), KEYCOLS (filed1, field2, field3);
Rpt file for replicat:
Oracle GoldenGate Delivery for Oracle
Version 11.1.1.1 OGGCORE_11.1.1_PLATFORMS_110421.2040
Windows x64 (optimized), Oracle 11g on Apr 22 2011 00:34:07
Copyright (C) 1995, 2011, Oracle and/or its affiliates. All rights reserved.
Starting at 2012-06-05 12:49:38
Operating System Version:
Microsoft Windows Server 2008 R2 , on x64
Version 6.1 (Build 7601: Service Pack 1)
Process id: 2264
Description:
** Running with the following parameters **
REPLICAT rtcheck
USERID tst, PASSWORD ***
DISCARDFILE ./dirrpt/rtcheck.txt, PURGE
SOURCEDEFS ./dirdef/sourcei.def
HANDLECOLLISIONS
UPDATEDELETES
MAP tst.table1, t.table1, COLMAP (USEDEFAULTS , filed9 = @GETENV("GGHEADER", "COMMITTIMESTAMP"), filed10= @CASE(@GETENV("GGHEADER", "OPTYPE"), "SQL COMPUPDATE", "U", "PK UPDATE", "U",@GETENV("GGHEADER", "OPTYPE")) ), KEYCOLS (field3);
MAP dbo.TPROCPERIODCONFIRMSTAV, TARGET R_019_000001.TPROCPERIODCONFIRMSTAV, COLMAP (USEDEFAULTS , field5 = @GETENV("GGHEADER", "COMMITTIMESTAMP"), filed6= @CASE(@GETENV("GGHEADER", "OPTYPE"), "SQL COMPUPDATE", "U", "PK UPDATE", "U",@GETENV("GGHEADER", "OPTYPE")) ), KEYCOLS (filed1, field2, field3);
CACHEMGR virtual memory values (may have been adjusted)
CACHEBUFFERSIZE: 64K
CACHESIZE: 512M
CACHEBUFFERSIZE (soft max): 4M
CACHEPAGEOUTSIZE (normal): 4M
PROCESS VM AVAIL FROM OS (min): 1G
CACHESIZEMAX (strict force to disk): 881M
Database Version:
Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
PL/SQL Release 11.2.0.1.0 - Production
CORE 11.2.0.1.0 Production
TNS for 64-bit Windows: Version 11.2.0.1.0 - Production
NLSRTL Version 11.2.0.1.0 - Production
Database Language and Character Set:
NLS_LANG = "AMERICAN_AMERICA.CL8MSWIN1251"
NLS_LANGUAGE = "AMERICAN"
NLS_TERRITORY = "AMERICA"
NLS_CHARACTERSET = "CL8MSWIN1251"
For further information on character set settings, please refer to user manual.
** Run Time Messages **
Opened trail file ./dirdat/dc000000 at 2012-06-05 12:49:39
2012-06-05 12:58:14 INFO OGG-01020 Processed extract process RESTART_ABEND record at seq 0, rba 925 (aborted 0 records).
MAP resolved (entry tst.table1):
MAP tst.table1, t.table1, COLMAP (USEDEFAULTS , filed9 = @GETENV("GGHEADER", "COMMITTIMESTAMP"), filed10= @CASE(@GETENV("GGHEADER", "OPTYPE"), "SQL COMPUPDATE", "U", "PK UPDATE", "U",@GETENV("GGHEADER", "OPTYPE")) ), KEYCOLS (field3);
2012-06-05 12:58:14 WARNING OGG-00869 No unique key is defined for table table1. All viable columns will be used to represent the key, but may not guarantee uniqueness. KEYCOLS may be used to define the key.
Using the following default columns with matching names:
field1=field1, field2=field2, field3=field3, field4=field4, field5=field5, field6=field6, field7=field7, field8=field8
Using the following key columns for target table R_019_000001.TCALCULATE: field3.
2012-06-05 12:58:14 WARNING OGG-01431 Aborted grouped transaction on 'tst.table1', Mapping error.
2012-06-05 12:58:14 WARNING OGG-01003 Repositioning to rba 987 in seqno 0.
2012-06-05 12:58:14 WARNING OGG-01151 Error mapping from tst.table1 to tst.table1.
2012-06-05 12:58:14 WARNING OGG-01003 Repositioning to rba 987 in seqno 0.
Source Context :
SourceModule : [er.main]
SourceID : [er/rep.c]
SourceFunction : [take_rep_err_action]
SourceLine : [16064]
ThreadBacktrace : [8] elements
: [C:\App\OGG\replicat.exe(ERCALLBACK+0x143034) [0x00000001402192B4]]
: [C:\App\OGG\replicat.exe(ERCALLBACK+0x11dd44) [0x00000001401F3FC4]]
: [C:\App\OGG\replicat.exe(<RCALLBACK+0x11dd44) [0x000000014009F102]]
: [C:\App\OGG\replicat.exe(<RCALLBACK+0x11dd44) [0x00000001400B29CC]]
: [C:\App\OGG\replicat.exe(<RCALLBACK+0x11dd44) [0x00000001400B8887]]
: [C:\App\OGG\replicat.exe(releaseCProcessManagerInstance+0x25250) [0x000000014028F200]]
: [C:\Windows\system32\kernel32.dll(BaseThreadInitThunk+0xd) [0x000000007720652D]]
: [C:\Windows\SYSTEM32\ntdll.dll(RtlUserThreadStart+0x21) [0x000000007733C521]]
2012-06-05 12:58:14 ERROR OGG-01296 Error mapping from tst.table1 to tst.table1.
* ** Run Time Statistics ** *
Last record for the last committed transaction is the following:
Trail name : ./dirdat/dc000000
Hdr-Ind : E (x45) Partition : . (x04)
UndoFlag : . (x00) BeforeAfter: A (x41)
RecLength : 249 (x00f9) IO Time : 2012-06-01 15:48:56.285333
IOType : 115 (x73) OrigNode : 255 (xff)
TransInd : . (x03) FormatType : R (x52)
SyskeyLen : 0 (x00) Incomplete : . (x00)
AuditRBA : 44 AuditPos : 71176199289771
Continued : N (x00) RecCount : 1 (x01)
2012-06-01 15:48:56.285333 GGSKeyFieldComp Len 249 RBA 987
Name: DBO.TCALCULATE
Reading ./dirdat/dc000000, current RBA 987, 0 records
Report at 2012-06-05 12:58:14 (activity since 2012-06-05 12:58:14)
From Table tst.table1 to tst.table1:
# inserts: 0
# updates: 0
# deletes: 0
# discards: 1
Last log location read:
FILE: ./dirdat/dc000000
SEQNO: 0
RBA: 987
TIMESTAMP: 2012-06-01 15:48:56.285333
EOF: NO
READERR: 0
2012-06-05 12:58:14 ERROR OGG-01668 PROCESS ABENDING.
Discard file:
Oracle GoldenGate Delivery for Oracle process started, group RTCHECK discard file opened: 2012-06-05 12:49:39
Key column filed3 (0) is missing from update on table tst.table1
Missing 1 key columns in update for table tst.table1.
Current time: 2012-06-05 12:58:14
Discarded record from action ABEND on error 0
Aborting transaction on ./dirdat/dc beginning at seqno 0 rba 987
error at seqno 0 rba 987
Problem replicating tst.table1 to tst.table1
Mapping problem with compressed key update record (target format)...
filed1 = NULL
field2 =
field3 =
field4 =
field5 =
datefield = -04-09 00:00:00
field6 =
field8 =
field9 = NULL
field10 =
Process Abending : 2012-06-05 12:58:14

Mapping problem with compressed key update record (target format)...

Hi Guys,
Getting below error while replication from Source to target. Source table is having NOT NULL Column, but on target replicat process giving error about some NULL value ??
How to overcome this issue, any idea...
2011-08-04 10:35:04 INFO OGG-00995 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: REPLICAT RMASTRK starting.
2011-08-04 10:35:05 INFO OGG-00996 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: REPLICAT RMASTRK started.
2011-08-04 10:35:06 WARNING OGG-00869 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: OCI Error ORA-01407: cannot update ("INFRA"."CUST"."CODE") to NULL (status = 1407), SQL <UPDATE "INFRA"."CUST" SET "ORD_ID" = :a2,"DP_ID" = :a3,"EXCHNG_CODE" = :a4,"ORD_QTY" = :a5,"ORD_PRICE" = :a6,"CODE" = :a7,"MKRT_CODE" = :a8,"CHANN>.
2011-08-04 10:35:06 WARNING OGG-01004 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: Aborted grouped transaction on 'INFRA.CUST', Database error 1407 (ORA-01407: cannot update ("INFRA"."CUST"."SCRP_CODE") to NULL).
2011-08-04 10:35:06 WARNING OGG-01003 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: Repositioning to rba 44132192 in seqno 68708.
2011-08-04 10:35:06 *WARNING OGG-01154 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: SQL error 1407 mapping INFRA.CUST to INFRA.CUST OCI Error ORA-01407:* *cannot update ("INFRA"."CUST"."SCRP_CODE") to NULL (status = 1407), SQL <UPDATE "INFRA"."CUST" SET "ORD_ID" = :a2,"DP_ID" = :a3,"EXCHNG_CODE"=:a4,"ORD_QTY"*
*= :a5,"ORD_PRICE" = :a6,"SCRP_CODE" = :a7,"MKRT_CODE" = :a8,"CHANN>.*
2011-08-04 10:35:06 WARNING OGG-01003 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: Repositioning to rba 44132192 in seqno 68708.
2011-08-04 10:35:06 ERROR OGG-01296 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: Error mapping from INFRA.CUST to INFRA.CUST.
2011-08-04 10:35:06 ERROR OGG-01668 Oracle GoldenGate Delivery for Oracle, rmastrk.prm: PROCESS ABENDING.
Oracle GoldenGate Delivery for Oracle process started, group RMASTRK discard file opened: 2011-08-04 10:35:05
Current time: 2011-08-04 10:35:06
Discarded record from action ABEND on error 1407
OCI Error ORA-01407: cannot update ("INFRA"."CUST"."SCRP_CODE") to NULL
(status = 1407), SQL <UPDATE "INFRA"."CUST" SET "ORD_ID" = :a2,"MKRT_CODE" = :a8,"CHANN>
Aborting transaction on ./dirdat/pm beginning at seqno 68708 rba 44132192
error at seqno 68708 rba 44132192
Problem replicating INFRA.CUST to INFRA.CUST
*Mapping problem with compressed key update record (target format)...*
ORD_QTY = 500
ORD_PRICE = 37430
SCRP_CODE =
MKRT_CODE = N
Oracle GoldenGate Delivery for Oracle process started, group RMASTRK discard file opened: 2011-08-
04 10:35:05
Current time: 2011-08-04 10:35:06
Discarded record from action ABEND on error 1407
OCI Error ORA-01407: cannot update ("INFRA"."CUST"."SCRP_CODE") to NULL
(status = 1407), SQL <UPDATE "INFRA"."CUST" SET "ORD_ID" = :a2,"MKRT_CODE" = :a8,"CHANN>
Aborting transaction on ./dirdat/pm beginning at seqno 68708 rba 44132192
error at seqno 68708 rba 44132192
Problem replicating INFRA.CUST to INFRA.CUST
Mapping problem with compressed key update record (target format)...
ORD_QTY = 500
ORD_PRICE = 37430
SCRP_CODE =
MKRT_CODE = N
Any inputs / help would be appreciated.
Regards,
Manish

The SCRP_CODE column has a NOT NULL constraint. The ORA-01407 error is telling you that you cannot update or set a value for this column to null because of the constraint. This has absolutely nothing to do with an index. You can use a marker/sentinel value in lieu of using NULL. For a numeric field, where everything is positive, a negative value (-1) can be decoded as meaning null. For a character field, a code such as NA can represent NULL.
This also has nothing to do (directly) with GoldenGate failing because of this error. The underlying SQL statement will fail everywhere, regardless of the tool or application. It is not a case of failing only in GoldenGate.

N8 and ovi map problem,server timeout

just got my new device and when try to update map application to have maps on the phone I alwys get the following eroor..server timeout...try again...I have tried all evening and same message again and again..I have Ovi suit version 2,2,1,23..It´s a new phone and it´s not working,I have tried on both windows XP and on Windows 7..I have reset the phone many times and if I don´t get this to work fast I will definately have my okd phone back and sell this one,hve read about other phones and they all experience the same problem with the latsest Ovi update...so what will I do???????..any suggestion,tried with version 2.1.1.1 and same problem...It´s a brand new phone and is not working..come on..
Solved!
Go to Solution.

Nokia's solution to update maps is exclusively using OVI Suite.
Ovi Suite is a tremendous piece of software: never checked before any release, always buggy.
You are lucky if you do not need maps because PC Suite is reliable.
You are cursed if you need maps...
Any upgrade of maps ends up in problems!
Today if failed again, I am used to it....
I will stop any use of this Nokia's E72 (it is their product, not mine) as soon as my contract with my provider will end!
My today's provider will also be punished by seeing me away definitively at the same time. And I will get away as many people as possible from Nokia!!!!!!!!!!!!!!!!!!!!!
I hate this product and this company: They are not concerned by their customers, they are just good at taking the money and run away.
That's Ok for me, you will be out of this market within 3 years with such an irrespect of your customers. -10% of market share / year is 0% in 3 years from now on. And, yes, it is too late: You did it again with the N8 (read above)!
Have a nice day!

Mapping problem with Wireless Keyboard and Japanese iPhone

Hi everyone:
This seems to be a slightly obscure question -- at least, I can't find a ready answer for it with the search terms I've tried, possibly because most people don't use this particular accessory with the iPhone.
I have an iPhone 4 that I bought from and use on Softbank, the carrier in Japan, where I live. While visiting the United States recently, I bought an Apple Wireless Keyboard from an Apple retailer. I wanted to carry it with me for use with my iPhone, so I would reliably have a convenient way to access the Internet without being confined to the touchscreen keyboard. (I live in a rural area where WiFi spots are uncommon, but my iPhone's access to Softbank's data network is fairly good and consistent.)
However, to my frustration, I can't use the keyboard due to a mapping problem. The Bluetooth connection is fine -- the iPhone can discover the keyboard. However, the mapping is off: typing "Q" gets me "A," typing "Z" gets me "W", numbers and punctuation are off, etc. The key point: This is NOT a problem with the International Keyboard settings (under the Settings -> General -> Keyboard -> International Keyboards menu). I have the Keyboard setting set to QWERTY, which is the layout of the Apple keyboard; I have tried all the other possibilities, just in case. None of them work. Setting the Keyboard setting to QWERTY does not make the external QWERTY keyboard map correctly.
The rather ironic addendum is this: While on a recent trip to Tokyo, I visited the Apple store in Shibuya and, after concluding the main business of my visit (discussing my MacBook's battery problems with an English-speaking staffer), I took out my iPhone and keyboard and asked him about my mapping problem. He started with the Keyboard menu, tried the same things I had tried, realized they weren't working, and puzzled over the problem for a while. Then he did this: He hit a key combination (I believe) that brought up a menu on the iPhone's screen. "Ah, there's your problem," he said, and selected a new setting. The problem was instantly fixed.
To my chagrin, however, I neglected to write down what "Ken" had done to fix the problem. Argh... I was looking at the iPhone upside-down; I'd already taken up more than half an hour; people were waiting, and I guess, being used to living in the countryside now, that I'm not used to Shibuya crowds any more. Anyway, I didn't take careful notes or ask him to walk me through it, and now I cannot recall or repeat what he did. And I still can't use my keyboard!
Any ideas or advice, anyone? How did "Ken" fix my problem, and how can I repeat it? Much, much appreciated, in advance.

THAT'S IT. Sir, you have solved my problem. Thank you!!
And I feel a little silly; this will doubtless seem to an expert as if it should have been obvious all along. But isn't that always the way in hindsight?
Here's what happened: The key combination I was trying to remember was "Apple/command + space on the hardware keyboard," as you just said above. The "menu" it brings up is, apparently, a list of keyboards. I take it that this list is the same as the list of the "virtual" keyboards on the iPhone? I have never had more than one external keyboard -- the Apple Wireless -- but I do have several keyboards active virtually, as the iPhone in Japan seems to come with both the "Nihongo Ten-key" and the "Nihongo Romaji" keyboards active, and I added several other languages as well.
When I hit "Apple/command + space," this list comes up on the iPhone's touchscreen. Highlighted and checked at the top is "English," just as if it had been selected all along. But nonetheless, when I first turn on and pair my keyboard with the iPhone, I need to perform this key-combination action, as if to "reselect" English, and then the keyboard promptly starts working properly as QWERTY. I can only assume that one of the others had been default-selected before -- presumably one of the Nihongo ones? -- and that this was causing the interference.
Thank you again! You have made me and my wireless keyboard very happy.

Free ovi Maps problem

Once again Nokia has exceded themselves in the field of ridiculousness:
I cannot download ovi maps OTA via software update on my phone and I have looked on the nokia website but cannot find a download for my laptop so I can install via USB.
I have an n97 with the newest software... please help.
(On another note, does anyone know why my n97 doesn't respond to any button/screen presses from time to time after unlocking screen? Any fixes?)

Hi, only way to get maps update is to go to nokia maps on phone browser and download N97 mini version ( it works perfectly) but it will take up about 9 meg of space on C. New version will be with V2.1 update when it arrives.
Good Luck
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

XSLT Mapping - problem with prefixes when calling template

Hi all,
I am having a problem with using an XSLT mapping in XI to combine various fields from 2 input messages of different structures into a single output message. I understand that XI puts a wrapper around the 2 input messages so the structure of the XML I am mapping is:
<?xml version="1.0" encoding="UTF-8"?>
<ns2:Messages xmlns:ns2="http://sap.com/xi/XI/SplitAndMerge">
<ns2:Message1>
<ns:(root of first message)>
</ns:(root of first message)>
</ns2:Message1>
<ns2:Message2>
<ns:(root of second message)>
</ns: (root of second message)>
</ns2:Message2>
</ns2:Messages>
Currently my XSL looks like the following:
<?xml version="1.0" encoding="UTF-8"?>
<xsl:stylesheet xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:ns="http://example.co.uk/example" xmlns:ns2="http://sap.com/xi/XI/SplitAndMerge" xmlns:javamap="java:systemDate.CurrentDate" version="2.0">
<xsl:output method="xml" version="1.0" encoding="UTF-8"/>
<xsl:param name="inputparam"/>
<xsl:template match="ns2:Messages">
...<xsl:calltemplate name="FormattingTemplate"/>
</xsl:template>
<xsl:template name="FormattingTemplate">
</xsl:template>
</xsl:stylesheet>
When I test the mapping it works fine until it calls the FormattingTemplate. Then it throws out a "transformer exception" error saying the prefix 'ns2' is not mapped to a namespace.
If anyone could tell me where I am going wrong I would be very grateful.
Thanks,
Mike

Hi Udo,
Thanks for your reply.
When testing the stylesheet locally with XMLSpy, it works fine, but I have just noticed that it adds information in the root tag of the target message as follows:
<(root of target message) xmlns:javamap="java:systemDate.CurrentDate" xmlns:ns="http://example.co.uk/example" xmlns:ns2="http://sap.com/xi/XI/SplitAndMerge">
I checked the root tag of the target message in XI and it does not automatically add this information. Thus I added it in my stylesheet so the information above is projected in the target message, but the same error message appears when the call template function is called. Do you know if I need to somehow add a namespace to templates other than the main one? If so, do you know how I go about doing that?
Thanks,
Mike

Port Mapping Problem with AEX

I have a new Airport Extreme and a problem that did not exist with the Airport. I connect a Toshiba network camera to an Airport Express, set as a WDS remote, with the netcam connected to the wired ethernet port of the Express. I can see the netcam, which also functions as a web server, on the internal 10.x.x.x address, and have reserved a discrete 10.x.x.x address via the MAC/DHCP reservation function of the Extreme. Just like the older Airport which did this without a hiccup, I should be able to map a port (e.g. 1200) on the public IP to port 80 of the internal 10.x.x.x address, then access the netcam on the internal network from any browser (http://67.x.x.x:1200). My cable modem is just that: no router involved other than the Airport Extreme. I'm using the latest Extreme and Express firmware, and am either missing something with the new Leopard firewall, overlooking something else, or dealing with a product flaw. Any help is appreciated and Happy Holidays.

I have forwarded the port (have tried several different ports actually) in what I think it the correct way: using the Airport Utility, connected to the Airport Extreme, and, under advanced options, selected port mapping, entered the public TCP port of 1200, then the private 10.x.x.x IP address of the netcam (which I can access from the internal network with no problem), coupled with the private TCP port of 80. I then attempt to access the netcam from the Internet by entering http://my cable modem IP address:1200 (or another port to which I've attempted to map). This method worked for two years with the Airport, but, with the Extreme and Leopard (simultaneous transition), I'm stumped. After reading other about other port mapping problems, I reserved an IP address for the netcam based on its MAC with no positive results. I also set the firewall through the Security icon in System Preferences to allow all incoming connections. Thanks for taking the time to respond.

Maps Problem with Glitchy Map Display

I've been having a problem with Maps recently. Lately, I've been scrolling across maps and very (very) often I would have a really glitchy layout that looks like this:
http://img137.imageshack.us/img137/442/mapsproblemrr6.png
This occurs on both 3G and WiFi wireless networks.
I've tried rebooting the phone (holding down power button and sliding the slider) and resetting my network settings already.
Any ideas?
Thanks for your help!

Zanneth-,
Does the map ever come into focus, or does it remain distorted? Does this issue occur when using different geographical searches? If so, I would try resetting all settings and then a restore, setting the iPhone up as a new phone.
You could also test installing Google Earth for the iPhone (available on the app store) to see if the same issue occurs as well.
Update and restore error messages on the iPhone and iPod touch
http://support.apple.com/kb/TS1275
Hope this helps,
Raleigh

Ovi maps problem

if i try to search using the browse function,,,,,,all i keep getting for any section is "no results found"
is there server down or something cause it was working fine the other day.
how can i fix it ? ? ? ? ?

2bad wrote:
I'd just offer this for the future. Be careful with commas. In my experience they're not necessary. However, in database / spreadsheet design, commas are used to "tab" from field to field. Once you start assuming that the software thinks, using the same logic as your mind does, then you will need to be very consistent in supplying the correct number of commas.
If you supply the wrong number of commas, the poor old database might end up looking for a city name in a field reserved for streets, or house numbers, and end up with no match.
Also, I've had mixed success in the past by assuming that a particular Application will undestand abbreviations. I stopped long ago using Rd for Road, Ave for Avenue, and ,say, NSW for New South Wales. It might well work, but don't be surprised if it doesn't.
Same uneven results without commas. Same uneven results using no abbreviations. Conclusion - Ovi Maps 3.03 search is just plain inconsistent.
And on the subject of abbreviations and commas, this is a GPS sat nav application. The core of it's functionality is searching for places and then navigating to them. If it doesn't understand common ways of writing addresses (eg. Rd = Road), or common geographic abbreviations within a country (NSW = New South Wales, CA = California) then it is not fit for the purpose for which it was supposedly designed. Other GPS applications (Garmin XT for one, Google Maps another) don't have any trouble finding the locations I want, but Nokia Maps does.
If I've helped you, you can thank me by clicking the green 'kudos' star on my post. Cheers.

Map problem with ios6

I have problem with IOS6 Maps is any one knows to downgrade to old IOS5 Maps

Load this map and save it on your Home Screen
https://maps.google.com/

N97 Ovi maps clashing with Google maps or sports t...

I have a UK Vodafone N97, Had Ovi maps working a treat and really pleased with it. However, I just installed google maps and then Nokia Sports tracker. Sports tracker wouldn't "track " at all and this then stopped Ovi maps from finding a signal.
However, Google maps finds 3-5 satellites and plots very quickly so I know the GPS receiver is working fine.
I uninstalled Sports tracker and Google maps, deleted all Ovi map data and did a soft reset, then re-installed Ovi maps for the UK ( I can not delete Ovi maps app from the phone, software V21)
I still cannot get a lock with Ovi maps but having put Google maps back on, that works fine!!
Any thoughts other than a hard reset as I have so much installed on the phone.
Thanks,
Martin

Google maps uses a different server, and installing it may have changed the server settings in the phone location settings. Go to Menu>Apps>Location>Positioning>Positioning Server> make sure that the server is still supl.nokia.com
If you find my post helpful please click the green star on the left under the avatar. Thanks.

Excel XML map problem with numbers.

Hi Xcelsius gurus,
Once again i need your help.
I use Excel XML maps to get data into my embedded spreadsheet, my data are current year sales per month like below:
115.450,36
220.336,20
189.222,56
200.005,48
just numbers.
After inserting the xml data i am not able to use them. No chart, No list, No gause can present my data. Like there is no data.
I realised that after mapping the XML, spreadsheet's cells showing an error, when i click on error icon there is an option to convert data to number, that fix the problem.
What could i do to solve this issue? Is there any problem with my XML file?
Pease help me with this one, i am confused.

Hi:
   what is your xml file format?
   you can try some ordinary xml format instead, here is a example:
   <?xml version="1.0" encoding="ISO-8859-1"?>
<bookstore>
<book catalog="Programming">
<title lang="en">C++ Programming Language</title>
<author>Bjarne Stroustrup</author>
<year>998</year>
<price>198.0</price>
</book>
<book catalog="Networking">
<title lang="en">TCP/IP Illustrated</title>
<author>Richard Stevens</author>
<year>1996</year>
<price>156.0</price>
</book>
</bookstore>

5800 Ovi map problems

Hi guys,
im quite new to this so help would be appreciated,
Everytime i open ovi maps and try to go online i get the error message 'something went wrong and the connection failed'?
i have no idea how to get around this or what to do so help would be appreciated.
Many thanks
James
Solved!
Go to Solution.

Hi, assuming you have the latest map app and your settings are ok everything should work ! Just in case, try this:
first connect phone to computer and use Nokia Software Updater or Ovi suite to check you have the latest software update.
Second go Menu-settings-application mngr.-installed apps.-scroll down to Ovi Maps/Nokia maps and select options-uninstall, do this for all maps software.
Third , go menu-Applications and scroll down to Location app and open positioning-positioning methodsand tick everything except Bluetooth GPS
Now go here and download the correct version for your phone and install this (the bottom download not the first one)
http://betalabs.nokia.com/apps/ovi-maps-beta-for-mobile/download_and_installation
Finally using Nokia Map Loader, remove all old maps on phone and download the maps for your region and install them to your phone, all should be fine
If it isn't you may need to do a soft reset which will take your phone back to 'out of the box' but you will have to set it all up again, and will need to backup your contacts'calendar and notes, NOTHING else, as settings may be causing your problem !! Then set up your phone again . If you don't have loads of apps and music etc on the phone I suggest soft reset first, then install maps as described.
Soft reset by dialling *#7370# followed by 12345 and phone will reset and be like new.
Good Luck
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

OVI map problem with E52

Similar Messages

Maybe you are looking for