P1606dn is set to manual, not dhcp.
I needed to move a laserjet P1606 between buildings and put in another ip-address.
I restored the factory settings (hold both buttons while its turning on..).
now the printer showes IPv4, subnet and gateway is 0.0.0.0 AND "IP counfigured by=manual".
I have attached the new ip-address to it´s mac address.
How do I set it to DHCP or how can I log in and manually put in the new ip-address ?
It doesn´t get the ip-address because it´s set to "manual" not "ip-auto". How can I log into the printer and change this?
Similar Messages
-
DHCPv6 Server. v6 IP only. Do I need IPv6 DHCP in case setting address manually. PROBLEMS
I want network without Ipv4, only IPv6. Ipv4 is disabled on server and client. After setting IPv6 address manually to 2000:1::1/64 I still have dhcp enabled on interface. And when installing roles (dhcp, dns server) on server it gives message that
no static addresses is available. Moreover after setting dhcp server scope 2000:1:: it serves addresses to dhcp server.
How set correct static IPv6?
After publish route:
netsh int ipv6 set interface Local adv=en man=en other=en
netsh int ipv6 add route 2000:1::/64 Ethernet publish=yes
I have two ipv6 addresses on client? Highlighted address stays as static after releasing adapter and it looks like I do not need dhcp server at all??
Ethernet adapter Ethernet:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Hyper-V Network Adapter
Physical Address. . . . . . . . . : 00-15-5D-01-02-06
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2000:1::35ac:d8ae:dac6:5b69(Preferred)
Lease Obtained. . . . . . . . . . : 22 dec 2013 11:28:33
Lease Expires . . . . . . . . . . : 22 dec 2013 11:39:48
IPv6 Address. . . . . . . . . . . : 2000:1::b542:48c6:ac2a:4a18(Preferred)
Link-local IPv6 Address . . . . . : fe80::b542:48c6:ac2a:4a18%12(Preferred)
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 301995357
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1A-48-61-B0-00-15-5D-01-02-06
DNS Servers . . . . . . . . . . . : 2000:1::1
NetBIOS over Tcpip. . . . . . . . : DisabledHi,
I got something similar with you.
Since I don’t have a DHCP server in my environment, I just specified a static IP for test. And when I ran netsh interface ipv6 set address “Local Area Connection”,
the IP didn’t modified as expected. It just ignored the old entry and added a new one.
It is worth mentioning, there is no problem with IPv4.
As a workaround, you can manually disable DHCP for the clients. -
So I got a brand new iPhone 4 from a Sprint retailer, and it came with the software that was available at the time of the release. I left it that way for a while and put music on it through iTunes (latest version as of 11/20/2012) with no problems. Then I updated the software on the iPhone to iOS6.0.1 and when i tried to put music on it through iTunes like normal the songs showed up in the library of the iPhone (still on the computer) however they were grey and they had a syncing symbol to the left as if it were still syncing the music. I waited and waited but it would not go away. then I clicked the arrow at the middle top of iTunes where it shows you what song is playing and everything else iTunes is doing, and it did not say that it was syncing the music like normal. Basically the library indicated the music was still syncing but iTunes was not putting it on. I currently have it set to manually manage music. I do not want to switch it to automatically sync or reset my iPhone because I will lose my information. Any immediate help would be greatly appreciated!
When I went to restore my phone, I may have found the cause of these problems. I never deleted all of my original synced songs before enabling iTunes Match.
When I just went to do the restore, I figured I'd delete all of my songs, then disable iTunes Match. After deleting about 3.5 GB of music and disabling iTunes Match, I ran the sync to backup my iPhone. It said there was still 2.2 GB of music. I checked my phone just in case and there was 2.2 GB there, probably the original synced songs that I never removed.
Anyway, I'm doing the restore now just in case and will respond tomorrow with how everything is working. -
Manually set IP addresses not working as needed
We have setup our DCHP server in that we manually not dynamically give IP addresses to workstations according to there mac addresses. But most of the time the the workstations go and get the IP addresses dynamically, and in this case most of the time we get IP conflict. Does it mean the giving IP addresses manually does not work properly in the DHCP configuration. For reasons, we need to use Manually assigned IP addresses not dynamically. And how can I trace why the manually configured workstation go and get IP addresses dynamically ?
It should work properly. Please post your configuration.
-
Since ios 6 update hotmail fetches or push on its own. I have hotmail set to manual. Best I can tell its only hotmail and not yahoo. Is this a known problem? How do I make hotmail stop checking for mail when I have it set to manual?
Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* On Windows you can open Firefox 4.0+ in Safe Mode by holding the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac you can open Firefox 4.0+ in Safe Mode by holding the '''option''' key while starting Firefox.
* On Linux you can open Firefox 4.0+ in Safe Mode by quitting Firefox and then going to your Terminal and running: firefox -safe-mode (you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
* Or open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
[[Image:FirefoxSafeMode|width=520]]
''Once you get the pop-up, just select "'Start in Safe Mode"''
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshooting extensions and themes]] article for that.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''
Thank you. -
Error during unattended install of SQL 2012 (..setting 'CLTRESULTDIR' does not exist.)
Hi ALl,
I'm trying an automated install of SQL 2012 on WIndows 2012, but I keep running into this error (using a configuration.ini file generated by running through setup and grabbing it just before I clicked 'OK')
Contents of summary log:
Overall summary:
Final result: Failed: see details below
Exit code (Decimal): -2068578304
Exit facility code: 1204
Exit error code: 0
Exit message: The specified directory 'C:\Program Files (x86)\Microsoft SQL Server\DReplayClient\ResultDir' for setting 'CLTRESULTDIR' does not
exist.
Start time: 2015-01-09 10:19:12
End time: 2015-01-09 10:20:07
Requested action: Install
Setup completed with required actions for features.
Troubleshooting information for those features:
Next step for SQLEngine: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for Replication: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for FullText: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for DQ: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for AS: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for RS: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for RS_SHP: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for RS_SHPWFE: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for DQC: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for IS: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for Conn: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for Adv_SSMS: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for SDK: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for BC: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for DREPLAY_CTLR: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for DREPLAY_CLT: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for BIDS: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for SSMS: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for SNAC: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for SNAC_SDK: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for Writer: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for BOL: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Next step for Browser: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Machine Properties:
Machine name: IDCSQLTST11
Machine processor count: 2
OS version: Future Windows Version
OS service pack:
OS region: United States
OS language: English (United States)
OS architecture: x64
Process architecture: 64 Bit
OS clustered: No
Product features discovered:
Product Instance Instance ID
Feature Language
Edition Version Clustered
Package properties:
Description: Microsoft SQL Server 2012
ProductName: SQL Server 2012
Type: RTM
Version: 11
SPLevel: 0
Installation location: E:\SQL_Server_2012_StandardEdition\x64\setup\
Installation edition: Standard
Product Update Status:
None discovered.
User Input Settings:
ACTION: Install
ADDCURRENTUSERASSQLADMIN: false
AGTSVCACCOUNT: NT Service\SQLSERVERAGENT
AGTSVCPASSWORD: <empty>
AGTSVCSTARTUPTYPE: Automatic
ASBACKUPDIR: C:\Program Files\Microsoft SQL Server\MSAS11.MSSQLSERVER\OLAP\Backup
ASCOLLATION: Latin1_General_CI_AS
ASCONFIGDIR: C:\Program Files\Microsoft SQL Server\MSAS11.MSSQLSERVER\OLAP\Config
ASDATADIR: C:\Program Files\Microsoft SQL Server\MSAS11.MSSQLSERVER\OLAP\Data
ASLOGDIR: C:\Program Files\Microsoft SQL Server\MSAS11.MSSQLSERVER\OLAP\Log
ASPROVIDERMSOLAP: 1
ASSERVERMODE: MULTIDIMENSIONAL
ASSVCACCOUNT: NT Service\MSSQLServerOLAPService
ASSVCPASSWORD: <empty>
ASSVCSTARTUPTYPE: Manual
ASSYSADMINACCOUNTS: DOMAINAA\SQLADMINS
ASTEMPDIR: C:\Program Files\Microsoft SQL Server\MSAS11.MSSQLSERVER\OLAP\Temp
BROWSERSVCSTARTUPTYPE: Disabled
CLTCTLRNAME:
CLTRESULTDIR: C:\Program Files (x86)\Microsoft SQL Server\DReplayClient\ResultDir
CLTSTARTUPTYPE: Manual
CLTSVCACCOUNT: NT Service\SQL Server Distributed Replay Client
CLTSVCPASSWORD: <empty>
CLTWORKINGDIR: C:\Program Files (x86)\Microsoft SQL Server\DReplayClient\WorkingDir
COMMFABRICENCRYPTION: 0
COMMFABRICNETWORKLEVEL: 0
COMMFABRICPORT: 0
CONFIGURATIONFILE: E:\SQL_Server_2012_StandardEdition\ConfigurationFile.ini
CTLRSTARTUPTYPE: Manual
CTLRSVCACCOUNT: NT Service\SQL Server Distributed Replay Controller
CTLRSVCPASSWORD: <empty>
CTLRUSERS: DOMAINAA\user12345
ENABLERANU: false
ENU: true
ERRORREPORTING: false
FEATURES: SQLENGINE, REPLICATION, FULLTEXT, DQ, AS, RS, RS_SHP, RS_SHPWFE, DQC, BIDS, CONN, IS, BC, SDK, BOL, SSMS, ADV_SSMS,
DREPLAY_CTLR, DREPLAY_CLT, SNAC_SDK
FILESTREAMLEVEL: 0
FILESTREAMSHARENAME: <empty>
FTSVCACCOUNT: NT Service\MSSQLFDLauncher
FTSVCPASSWORD: <empty>
HELP: false
INDICATEPROGRESS: false
INSTALLSHAREDDIR: C:\Program Files\Microsoft SQL Server
INSTALLSHAREDWOWDIR: C:\Program Files (x86)\Microsoft SQL Server
INSTALLSQLDATADIR: <empty>
INSTANCEDIR: C:\Program Files\Microsoft SQL Server
INSTANCEID: MSSQLSERVER
INSTANCENAME: MSSQLSERVER
ISSVCACCOUNT: NT Service\MsDtsServer110
ISSVCPASSWORD: <empty>
ISSVCSTARTUPTYPE: Automatic
MATRIXCMBRICKCOMMPORT: 0
MATRIXCMSERVERNAME: <empty>
MATRIXNAME: <empty>
NPENABLED: 0
PID: *****
QUIET: true
QUIETSIMPLE: false
ROLE:
RSINSTALLMODE: DefaultNativeMode
RSSHPINSTALLMODE: SharePointFilesOnlyMode
RSSVCACCOUNT: NT Service\ReportServer
RSSVCPASSWORD: <empty>
RSSVCSTARTUPTYPE: Manual
SAPWD: <empty>
SECURITYMODE: SQL
SQLBACKUPDIR: <empty>
SQLCOLLATION: Latin1_General_CI_AS
SQLSVCACCOUNT: NT Service\MSSQLSERVER
SQLSVCPASSWORD: <empty>
SQLSVCSTARTUPTYPE: Automatic
SQLSYSADMINACCOUNTS: DOMAINAA\SQLADMINS
SQLTEMPDBDIR: F:\TempDB
SQLTEMPDBLOGDIR: <empty>
SQLUSERDBDIR: E:\SQLData
SQLUSERDBLOGDIR: D:\SQLLog
SQMREPORTING: false
TCPENABLED: 1
UIMODE: Normal
UpdateEnabled: true
UpdateSource: MU
X86: false
Configuration file: C:\Program Files\Microsoft SQL Server\110\Setup Bootstrap\Log\20150109_101753\ConfigurationFile.ini
Detailed results:
Feature: Database Engine Services
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: SQL Server Replication
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Full-Text and Semantic Extractions for Search
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Data Quality Services
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Analysis Services
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Reporting Services - Native
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Reporting Services - SharePoint
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Reporting Services Add-in for SharePoint Products
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Data Quality Client
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Integration Services
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Client Tools Connectivity
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Management Tools - Complete
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Client Tools SDK
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Client Tools Backwards Compatibility
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Distributed Replay Controller
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Distributed Replay Client
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: SQL Server Data Tools
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Management Tools - Basic
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: SQL Client Connectivity
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: SQL Client Connectivity SDK
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: SQL Writer
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: Documentation Components
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Feature: SQL Browser
Status: Failed: see logs for details
Reason for failure: Setup was canceled for the feature.
Next Step: SQL Server Setup was canceled before completing the operation. Try the setup process again.
Rules with failures:
Global rules:
Scenario specific rules:
Rules report file: C:\Program Files\Microsoft SQL Server\110\Setup Bootstrap\Log\20150109_101753\SystemConfigurationCheck_Report.htm
Exception summary:
The following is an exception stack listing the exceptions in outermost to innermost order
Inner exceptions are being indented
Exception type: Microsoft.SqlServer.Chainer.Infrastructure.InputSettingValidationException
Message:
The specified directory 'C:\Program Files (x86)\Microsoft SQL Server\DReplayClient\ResultDir' for setting 'CLTRESULTDIR' does not exist.
HResult : 0x84b40000
FacilityCode : 1204 (4b4)
ErrorCode : 0 (0000)
Data:
SQL.Setup.FailureCategory = InputSettingValidationFailure
DisableWatson = true
Stack:
at Microsoft.SqlServer.Chainer.Infrastructure.InputSettingService.LogAllValidationErrorsAndThrowFirstOne(ValidationState vs)
at Microsoft.SqlServer.Configuration.SetupExtension.ValidateFeatureSettingsAction.ExecuteAction(String actionId)
at Microsoft.SqlServer.Chainer.Infrastructure.Action.Execute(String actionId, TextWriter errorStream)
at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionInvocation.ExecuteActionHelper(TextWriter statusStream, ISequencedAction actionToRun, ServiceContainer context)
Inner exception type: Microsoft.SqlServer.Configuration.DistributedReplayExtension.DirectoryNotExistException
Message:
The specified directory 'C:\Program Files (x86)\Microsoft SQL Server\DReplayClient\ResultDir' for setting 'CLTRESULTDIR' does not exist.
HResult : 0x87d00006
FacilityCode : 2000 (7d0)
ErrorCode : 6 (0006)
Data:
DirectoryPath = C:\Program Files (x86)\Microsoft SQL Server\DReplayClient\ResultDir
SettingName = CLTRESULTDIR
WatsonData =
Microsoft.SqlServer.Configuration.DistributedReplayExtension.DirectoryNotExistException@6Hello,
Open the configuration file with notepad, then go to the “features” variable. On the following article you will find what
means each parameter:
http://msdn.microsoft.com/en-us/library/ms144259(v=sql.110).aspx#Feature
You will also find the list of features supported by each edition on the following article:
http://msdn.microsoft.com/en-us/library/Cc645993(v=sql.110).aspx
For example, it seems you have DQ and DQC on that configuration file, please remove them with their corresponding commas.
Hope this helps.
Regards,
Alberto Morillo
SQLCoffee.com
Thanks Albert that worked when I just selected the main features and excluded ones like DQ and DRC. Thing is why would the standard media allow you to install enterprise features, create a configuration file with these enterprise features and then fail?? Why
would Microsoft tease you like that? Frustrating since I spent hours on this .. -
My ipod nano isn't syncing when I try and change the setting in manually, but is however syncing when I launch the itunes by plugging it in. I'm wondering if anyone has had this issue and/or had been able to fix the problem?
Do you have any better luck with that if you update to iTunes 10.6.1.7?
From the notes for the release:
iTunes 10.6.1 provides a number of improvements, including:
• Fixes several issues that may cause iTunes to unexpectedly quit while playing videos, changing artwork size in Grid view and syncing photos to devices.
• Addresses an issue where some iTunes interface elements are incorrectly described by VoiceOver and WindowEyes.
• Fixes a problem where iTunes may become unresponsive while syncing iPod nano or iPod shuffle.
• Resolves an ordering problem while browsing TV episodes in your iTunes library on Apple TV.
http://www.apple.com/itunes/download/ -
My Ipod touch is set to manually manage music. I have put music from my computer and iTunes account onto it, and music from other people's computer and iTunes accounts on it. Unfortunately I dropped my iPod and the screen cracked. It still plays music and everything just fine, but it has problems with it's battery life so I'd like to just get a completely new iPod nano. Is there any way I can transfer all the music from my iPod touch onto a new iPod nano? From what I can tell it won't let me sync any of the music on my iPod touch that is from other people's computers onto my laptop, and so I wouldn't be able to put it on a new iPod nano. Hopefully that makes sense. I'd just really really like to be able to keep all that music and not lose 2/3 of my iPod touch music library because I want to put it on a newer Ipod.
Recovering your iTunes library from your iPod or iOS device: Apple Support Communities
-
How do I create an ACR custom lens profile if camera exposure can't be set to manual?
How do I create an ACR custom lens profile if camera exposure can't be set to manual?
I ask this question for the Nokia 808 PureView 41MP camera. It produces stunning image quality but exposure can only be controlled via EV +/- compensation. I need a lens profile to correct for vignetting to get even skies in panorama (which turn out stunningly otherwise). There is no profile for the Nokia 808 PureView I am aware of and I'd like to produce one.
Is the Adobe profile creator able to correct for varying exposure using EXIF or overlapping parts of the chart or background?
Or would the Adobe profile creator ignore EXIF if I use studio flash to enforce a constant lightning situation, even if shutter speed would vary (aperture is constant and ISO can be set constant, just not the shutter speed)?
Or did Adobe produce a profile internally they can share?
Thanks.If you read the first post, this is the camera-app of a 41MP Nokia Pureview 808 camera-phone, so maybe someone could write a new camera app but the phone is Symbian OS which is dead, making that unlikely.
http://www.digitaltrends.com/mobile/the-skeptics-guide-to-nokias-808-pureview-five-reasons -41-megapixels-are-not-a-gimmick/
http://www.digitaltrends.com/mobile/the-nokia-lumia-820-and-lumia-920-too-little-too-late/
It would probably be easier for Adobe to rewrite the LPC to allow vignetting to be computed from a single shot of a blank wall without a target in the shot, than to have someone rewrite a camera app that allows manual exposure.
Another idea about how to get the phone to keep a constant exposure would be to experiment with putting darker and lighter objects in the field-of-view away from the target area to make the camera metering adjust things so it’s exposure is the same from one shot to the next. This would take some doing but should work, unless the LPC uses the part of the frame that doesn’t contain the checkboard target in its computations.
You’re basically varying the scene around the target so the camera takes the same exposure of the target each time. -
Elements 8 Error 150:30 FlexNet is Set to Manual
I have the all-too-common Error 150:30 when trying to open Edit in Photoshop Elements 8. I followed instructions posted elsewhere to be sure the FlexNet service was set to manual, but even after a re-boot, the error persists. Any other ideas?
Actually, by default, the service should be in running state when application launches and the mode should be set as "Automatic".
The Tech doc which you have referred just says that even when the service is indeed running in Automatic mode and still the application is giving this error, then you set the service in Manual mode and start it manully before launching application.
But, a better approach will be to make sure that you log in with admin user, check the services.msc to see whether the service is installed on the machine or not and launch the application and see whether the service is changing to running mode or whether it is still in stopped state.
You can refer the below Tech Doc and follow the solutions sequentially to see of they get you out of this issue:
http://kb2.adobe.com/cps/405/kb405970.html
Regards,
Ankush -
Bug in OS 3.0: mail accounts set to "Manual" are pushed at bootup
I keep my iPhone's mail accounts on "Manual" access only, so that I'm not overwhelmed with email during the day. I also use MobileMe, and I have my contacts and calendars set to "Push." This combination is possible in:
Settings -> Mail, Contacts, Calendars -> Fetch New Data -> Advanced
In OS 2.2.1 and below, this combination worked as expected: contacts and calendar items are pushed via MobileMe, and mail is retrieved only when entering the Mail app. It also works as expected in OS 3.0, except ...
... when the phone is rebooted. At reboot, all mail accounts are pushed, as if the OS is overlooking my "Manual" setting. I've reported the problem to Apple via the iPhone feedback form, but I thought it prudent to mention it here as well, since it's repeatable and others may notice the problem as well and search for it.Just wanted to keep this alive. Whenever we restart either my 3GS phone or my wife's 3G they make an immediate mail check and download any emails. Both phones are set to manual for mail checks and we use Me.com for all of our email. With the 3G phone, it was originally mine and before the 3.0 software upgrade it never did this. So I'm going to chalk it up to the 3.0 and believe that some future update will address this.
John -
Album order (after "sort photos manually") not staying
I have an album of about 500 pictures (from my 10,000 library). I sorted the pictures in it manually, but every time I close iPhoto and then reopen it, the order is messed up a bit with random pictures are out of order.
any ideas?
rogerI was unable to duplicate your problem with an album of 16 photos. Try deleting the iPhoto preference file, com.apple.iPhoto.plist, that resides in your User/Library/Preferences folder and try again.
NOTE: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding the the Option key. You'll also have to reset the iPhoto's various preferences.
Did you check to see if the sort order was still set to Manually? -
Iphone automatically checks mail even though it's set to "manual" check
In settings > mail, Auto-check is set to manual, but my phone still vibrates and beeps periodically -- even when it has been asleep and I'm not touching -- announcing that new mail has arrived.
I'm using it to check a yahoo and a gmail account. Why is it still checking mail automatically?Actually I just figured this out myself. You can turn it off by going to
Settings > Mail
and then clicking on your yahoo account. At the very top of the screen for your yahoo account settings, there's a button that says "Account ON or OFF"
Switching it to OFF means it won't show up at all in your mail program but it also won't push. Switching it back on makes it show up immediately in your mail program again. -
Updating and iPod that has preferences set for "manually manage songs..."
I have my iPod set with "manually manage songs and playlists" so that
(a) it won't try to update every time I connect it; and
(b) so that I can see all of the songs from my iTunes application, as I don't store my music library on my laptop computer.
But sometimes I do want to do a full sync of the iPod to my music library. I'm not sure how to do that. If I select "update ipod", it says "iPod update complete", but doesn't really do anything.
Any ideas?
thanksHi, Michael, and thanks for your help.
I realize I can change the options to "automatically update..."
But the whole point of my inquiry was to find out whether there's a way to NOT have that preference set, as I
(a) don't want the iPod updating every time I plug it in; and
(b) want to be able to see its songs on other computers when I'm not seeking to update it.
What I want is a command that I can initiate that will say "act as though the automatically-update preferences were on and do a full update just this once".
I suppose I can go in and turn the preference on, do the update, then turn the update off, but it seems like lots of steps. I might have thought that there would be a control+click command that would accomplish this all in one click. -
When running FB game apps, the image loaded is too large for the FB space. The program looks for a "zoom" setting and does not find it. This was from the error screen. I have not been able to locate where the image zoom is located (found the font adjustment). I am new to FireFox and would like to sort this out please.
Your installed plug in assume Shockwave Flash 10.3, but I thought it was Adobe Flash 10.3. Are they one and the same?
Below is the warning message from the Error ConsoleI'm not sure the CSS warning is relevant to Flash. Maybe adjust your overall zoom level on Facebook manually from the View menu?
View > Zoom
If you have the orange Firefox button, tap the Alt key to display the classic menu bar.
Maybe you are looking for
-
Can't Change Lock Screen Background Image and User Account Picture in Windows 8.1.
I am running Windows8.1 Single Language with windows activated. Upgraded from Window 8 to Windows 8.1. Lenovo Y410p. 4th generation Intel® Core™ i7-4700MQ (2.40GHz 1600MHz 6MB) with 16GB RAM. NVIDIA® GeForce® GT750M 2GB . I tried all methods that I f
-
Photoshop Element 12 not installing on new (June 2014) iMac OS X 10.9.4 from DVD
DVD is in Pioneer BDXL Blu-ray/DVD/CD drive USB drive. First screen of installer gives me choice to install as a purchase or a trial. Next screen (purchase or trial) says I have to sign into my Adobe ID. There are no fields in which to enter data.
-
Hi i extend the VO. import vo succcessfully. But i wann to deltete VO Substitution. first i removed substitution from Project Properties. then i run the jdr_utils.deletedocument script., i got msg document deleted successfully. But i want to again im
-
Hi all, Iam working on swing project which uses Undo/Redo feature for drag and drop figure and delete,cut,copy,paste and all the feature which ever want to use, and iam using multiple internal frames so the feature Undo/Redo should be specific to per
-
Hello! My apologies as this is the first time I have had a real issue with Skype... I've had a few messages in the past, claiming to be a single 23-year-old female who is interested in video chatting on a site where you have to give credit card infor