P2 batch capture problem

In short we keep FCP projects for each p2 card we unpack just incase we need to come back to them.
I have now had to come back to one to re-unpack the card at a different codec Prores 422 instead of Prores 422 HQ. I have encountered a strange problem all the files that are under 2GIG if you select them with batch capture open the log and transfer window and all is fine. But any files larger than 2 GIG FCP thinks its a tape rush and will only open log and capture so i cannot easily recapture them.
I have done lots of test with different cards, projects everything and get the same problem every time. Also this happens in our conform project too and i have tried it on 4 different computers on FCP 6 and 7 same problem every time.
I know i can easily re-unpack the whole card with out having to do this but this is a strange problem that shouldn't be happening and would like to solve it.
im running FCP 7 on OSX 10.5.8 processor 2 x 2.26 quad core intel xeon 8 GIG ddr ram
any thoughts would be appreciated!

Sorry everyone. I just noticed a post two down with the same issue. Have read through it and I'm not sure there's a solution there for me, but I'll give a few things a try. Apologize for what the double post. Any suggestions would still be appreciated.

Similar Messages

Premiere Pro CS5.5 Batch Capture Problems

Hi,
I'm sorry for the repost, but the older questions I can find on this topic won't allow me to reply and they were never answered (last post several months ago).
I'm having the batch capture problem with Premiere Pro CS5.5. Capture with device control works great when single capturing. When I log clips and attempt to batch capture, though, I get the "capture failed: device not found" error in my capture log. I have checked through the FAQ and the complete premiere manual on batch capturing. I've set my device (still using a Canon XL1) and even checked the video size...it matches that of my project (someone on another forum mentioned that this could be an issue). I have had no luck.
Could anyone tell me if this issue has been resolved, or redirect me to a resolution?
Thanks in advance for any help!!
Steve

I have encountered this problem if the current tape position is beyond the last recorded point when you start the batch capture or if any "OUT" points are beyond the last recorded position or if the capture spans any unrecorded portions of the tape. I always thought it was my camera but maybe it is a PPro issue.

Batch Capture Problem with 5D mark II

At the end of an event we normally copy all cards to the HDD, each card in a separate folder. We then point FCP at the card folders and use log & transfer to ingest the footage and transcode to ProRes 422.
Once all the footage is ingested we save the project and copy it from the Mac Pro to the iMac so that a second editor can work on it at the same time. Because the iMac doesn't have a RAID we set all the footage to 'offline' and use batch capture to recapture it all in ProRes Proxy.
So far so good.... that is with all the Panasonic HMC footage.... BUT we recently started shooting on the Canon 5D2 and 7D as well and this simply isn't working.
For some reason FCP recaptures all the Panasonic footage but refused to re-capture the Canon footage. I can see all the files in the L&T window but it never seems to equate the footage with the files I am trying to recapture.
HELP! What could be causing this? It's only a problem with the Canon footage.
Both MacPro and iMac are running identical versions of FCP and identical (latest) versions of the Canon L&T plug in ..... and YES we copied the entire CF card to a folder - just like we do with the Panasonic HMC stuff.

Hi Andy, compressor is current chugging away, so we'll get going for the edit I am sure. Only 600 more clips to go
I've tried everything I can think of in terms of recapturing. Even on the original Mac Pro that the footage came in to, if I copy the entire project folder (including the 'cards' folder) from one RAID to another it fails to recapture in the original project using the original codec (ProRes 422), but if I point it back to the original cards folder it works fine. It seems to be 'moving/copying' the cards that is causing the problems.
I've checked the dates and sizes on the copied files and they are all the same, and since recapturing to the original project at the original settings doesn't work once moved I am completely stumped....!

Batch capture problems HDV

Hi we are trying to batch capture HDV 1080i 25fps footage filmed from both a Sony Z1 and Z7 camera in Final Cut Pro 7. The problem comes when we try and batch capture or clip capture logged footage in final cut pro, the tape seems to be stuck in a continuous preroll loop on the first clip that needs capturing, the only way to capture any footage is through capture now. Finally the capture deck we are using is a Sony HVR-M15AE deck.
Any help would be greatly appreciated

Sounds like there may not be enough preroll space on the source tape ie not enough preceding unbroken timecode to allow for the preroll time needed ... if so then you may need to try a shorter preroll for that clip. Check (and possibly edit) the preroll setting in your Audio / Video Settings >> Device Control Preset. (You may just want to create a temporary duplicate preset for this shorter preroll setting).
Hope it helps
Andy

Batch Capture problems - can't read timecode

I want to log all my clips before capture and then just batch capture it all. Problem is, I get a message that the timecode can't be found.
How can I correct this problem?

I forgot nothing. My list is what is required to begin to log and batch capture. He didn't say it "started to capture but aborted midway through the first clip". He couldn't get started. We could go into a long list of tape based "do's and don'ts" but it didn't seem appropriate until we had some basic information.
We still don't know if the material was originally recorded on the playback cam and/or if he has ever successfully captured using this cam.
Don't you like playing 20 questions too? lol.
x

Canon Camera - Batch Capture Problems

Hi. I understand this is a common issue: I am using a Canon XL1 for interviews. I black out the tape in advance to avoid TC breaks, but when I use Batch Capture, I still run into "broken time code" messages. So, I end up using Capture Now, which is less efficient, so far as I can tell. I'm using a G5, 2.3 Gz, Dual Processor. As to Michael Grenadier's answer below, what does a firewire card do?
Thanks, as always!
Scott
This from Michael Grenadier:
There have always been issues with canon cameras. Try capturing with firewire basic device preset and see if that helps. The broken timecode error can also indicate some other thruput problem. Making sure your camera and hard drive are on seperate firewire busses can often help this problem. You need to add your equipment and os/software configuration to your profile to help analyze the problem. If you're using a tower, even though there are multiple firewire ports, there is only ONE firewire bus. Adding a firewire card can help.

Maxx, Thanks. In the past, I've taken the pre-post
TC break approach, but I always end up with an error
and no batch capture. I thought Batch Capture
doesn't work when there are TC breaks? Is there a
setting I'm missing?
We don't have a deck, so we use the XL1. I can try
my small camcorder though.
Very good to know about the XL2 - can we have yours?
hanks!
PLease take them both... I've been looking for an excuse to push for some new gear.
Typically I log all of my clips and then batch them from the browser. That way I can select a couple of clips at a time if the tape is that bad. And it has been before. We've got 1 shooter that likes to review shots but never rolls off any xtra tape before he does this. So everytime does it there's a TC break. But if the tape is bad or just doesn't have solid TC then you may be screwed.
Your camcorder will work just fine. I suggested this b/c that way you would at least know if you have a playback issue with your xl1 or if the tape just doesn't have solid TC.
Take a gander at Kevan's post as well. He asks some good questions and makes some good points as usual. I agree with what he said about blacking the tape. Back in my news days we had to do this and it was to be able to assemble edit deck to deck. No need to do this now though in this day and age of instant gratification. Boy I miss the days of blacking tapes, taking feeds, and sprinting through the news room with a tape as the anchor was leading into the story and tossing the tape to the tape op just in the nick o time... Ahh good times!

Batch capture problem

I'm trying to batch capture my clips, so i logged them all but when i select them all and choose batch capture an error comes up after a while and says "end of tape reached". The only footage i have on my tape goes from the beginning of the tape to about three minutes in. Can someone please help me here.
thanks,
Paul

Don't know if you are still looking for a solution to this but...
You most likely set your in point very near the first code on the tape. FCP needs to roll back a few seconds, before the in point, in order to ensure the deck gets up to speed before the capture begins. If it rolls back and can find not code before your in point, things get confused and FCP will not do the capture. This is also why, when shooting, you should always roll at least 5 seconds before the action starts.
Try moving the in point forward at least seconds.

Major Batch Capture Problem! Please, Please Help!!!

I have a project that is 1hr 41 minutes. The footage is on 3 tapes.
I need to re-capture the footage into this project to make some changes. When I try to batch capture the clips, I get an error saying that I am trying to capture drop-frame footage to a non-drop frame clip. This of course (it would seem) is impossible, as the footage was captured from these very same tapes.
I first tried ignoring the warning and capturing the footage, but that didn't work, and all the footage was in the wrong places.
I then looked at the off-line time code and went to the same time-code on the original tapes, and the time code is not correct! For instance, at the beginning of the sequence, the person introduces themselves. This footage is from tape 2 at timecode 2:06:48:07. If I go to that timecode on the tape, that is not what is there.
Does anyone have any clue what I could have done wrong? Is there even a way to change a clip from drop-code to non-drop?

It is true. Try it. I just did to make sure.
When you capture a clip using Capture Now AND Non-Controllable Device, the timecode starts at 0:00:00:00 each time you begin to capture a new clip.
If you use the device control & capture now, you retain timecode from the source tape. But if you turn off device control, you turn off timecode.
The FCP manual talks about it on I-276, but the language is pretty vague. It basically tells you the ONLY time you should set it to Non-Controllable Device is when you don't have timecode to begin with.

Batch Capture Problems - only some of batch being captured each time

I'm editing on a MacBook Pro with final cut version 5.1.4., with an operating system of OSX 10.4.10, off of an DVX100B in NTSC mode (at 30P settings) and when I try to Batch Capture, it won't capture all the clips. It acts as if it's capturing all of them, and at the end it tells me it has, but when i press "ok", there are only about a third of them that were actually captured, and I have to start again, and go through the batch about 4-5 times to get them all captured.
HELP!
Thanks

Superstitious, indeed.
As noted, we can't tell much from where we're sitting. Welcome to the forum, too.
Beginners' issues with batch capturing are often traced to not completely understanding how logging works. Maybe you have designated several overlapping clips.
bogiesan

Batch Capture Problems

I want to recapture a project, edited in SD as a HD project. Therefore I offlined all clips and recapture them in HD-Format. But the in and out of the clip was noct correct. Trying to use a exported batchlist in csv-Format I recognized that In and Out-Points of all clips differ from one to several frames. How can I batch capture material with correct timecode or export a correct batch capture list????
Thank you for instant help, because I have to finish HD editing on Monday
Jörg

No it's several clips on the tape. It captures 2 frames of each and then moves on to the next. Never actually heard of Rescue before but I shall check it out.One thing I have just noticed is that all the offline clips logged and ready to be captured don't have any compressor details, Vid rate or data rate details. That has to have something to do with it but I don't know what?
Thanks.

Serious Problem Batch Capturing HDV

I just searched through about 10 pages of this Forum and I could not find anyone with the exact Same problem. I am Using a G4 Mac with 1 GB of RAM with Final Cut 5.0 and I am trying to Capture Footage From a Friends Sony HDV HDR-FX!. I have logged about 18 clips for about 41 minutes of footage. Everytime I go to Batch Capture I tell it to Capture all of the clips and it instantly says Cannot Locate Timecode... Thank You in Advance if you can help, and the sooner the better.

FWIW, Here's the way I worked successfully last summer on a project that was shot on some sony HDV camera. We rented a Sony HDV deck. I went to the end of the tape and marked an out, I went to the beginning of the tape, let the tape roll for about 5 seconds or so and marked an out. I had "abort capture on dropped frames" and "create new clip on time code break" enabled in preferences. Captured the entire tape as HDV. FCP created a number of clips. I then batch captured these clips as DV so I had both HDV and DV clips. Both parts of this process worked flawlessly.
I wonder whether you've got enough RAM. Is FCP5.0 compatible with this camera? Are you sure you're using the correct capture preset? I'm not sure what variations the camera is capable of, but are you sure that you're capture preset exactly matches the format you were shooting (frame rate, pixel dimensions, etc.).

Problem batch capturing

FCP HD 4.5, easy set-up (DV-NTSC)
I'm trying to batch capture 10 clips. Each clips starts to capture for about 3 seconds and then it stops and says "error". I try pressing "continue" but it keeps trying to capture the same clip and I get the same message.
What am I doing wrong?
I just batch captured another tape and it captured fine.
thanks for the help.
Gerry

I just batch captured another tape and it captured
fine.
Perhaps an obvious question but....is the name of the tape you're capturing on still from the previous tape you captured? It does happen sometimes.

Problems with Batch Capture

I have a G5 Quad and Final Cut Studio (with FCP 5) and am running Leopard. Everything was running smoothly until about 2 months ago. I reinstalled Leopard ... from a clean install. I reinstalled FCP and everything worked well, EXCEPT. Now when I try a Batch Capture ... I set up 5 or 6 clips then tell FCP to capture all. It will rewind to the first clip ... the screen shows "go to cueing source material" ... less than a second of the clip shows, the screen then shows "go to cueing source material" ... then I get an error message - "dropped frames"
This is the same camera that I used before the install. I am hoping that this is just some "dumb" thing I forgot to click.
Any suggestions

Which camera? Also post the last time you had it serviced... if the heads get dirty or the tracking is off one whit, you'll get these error messages.
Jerry

Log and capture problems for HDV using FCP 5.0.1

I cant seem to get a picture in my log and capture browser when using HDV. The screen says my camera is connected, I see timecode correctly rolling in sync with my cameras timecode, I can use the controls, but no picture on the screen?
When I hit capture now, the capture screen pops up and gives a message "waiting for data from device".
we shot at 720p at 25fps, there is no capture preset for this in my version of FCP. Could this be the problem? Please help!!

Thanks for responding.
It's a mac osx 10.4.11 and a 2 ghz intel core duo. I'm using easy set up in final cut pro, but there is no option for hd fire wire basic (which apple support told me to look for). The only hd options are 1080i50, i60 and 720 p30. The other hd options are for the apple intermediate codec. When I use the easy set up for hd 1080i60, then go to log and capture, it doesn't give me the preview window to set in's out, batch capture etc. It only lets me capture straight from the camera and I have to manually stop it and start it which is a major pain. Plus the clips need to be rendered once I put them in a timeline. I've shot and edited on mini dv with final cut for nearly 7 years, but now that i've tried to upgrade and shoot hd mini dv, all of these problems have arrived in capturing. I'm starting to think my version of final cut pro (5.0.1) just doesn't work with hd, unless it's very time consuming. Any ideas?

Capture Problem with FCP 5.1

I just loaded 2 new titanium macbookpros with 5.1. When testing the basics of the programs I found that one worked fine and the 2nd kept quitting FCP when I batch captured some test clips. I tried throwing out the preferences and when that didn't help I tossed the entire program and all related files and reinstalled the suite. Still having the same problem of quitting on the capture. What do I do? I'm leaving for India on Thursday and need a solution yesterday! Has anyone out there had a similar problem or did I just buy a faulty computer?

I know you said you threw out your preferences, but have you tried it using FCP Rescue? If not, try this link, download the correct version, then follow the additional instructions posted below by Brian Conner in a previous thread.
http://www.pistolerapost2.com/fcprescue/
"In some rare cases, you have to modify that sequence of actions.
After the step where you trash the prefs in Rescue, quit Rescue, start FCP, create a new project & change a couple of settings. Doesn't matter what, because later you'll be trashing them.
Now quit FCP and Shut Down the Mac. (Shut Down, not Restart.) Then boot up again. In a Finder window, confirm that the FCP preferences files exist.
Now start FCP again and set the prefs the way you want them. Close the project, so that NO projects are open. Quit FCP.
Open FCP Rescue 5. You should not be getting a corrupt settings message. Click Backup and quit Rescue."
Hopefully that will do the trick, or post back if still needing help.
K

P2 batch capture problem

Similar Messages

Maybe you are looking for