P35 NEO MS-7360 Replacement Battery

Hi, i believe i need a new battery for my motherboard as i am frequently met with "CMOS time and date not set" when i boot up my computer and i am just checking before i buy a new battery that i am getting the correct one. I have written down what is printed on the front of the battery: "KTS, Lithium Battery, Japan, STD, CR2032" and after looking around on the internet for a replacement battery i found a site where i plan to purchase one from. Will this battery be a suitable replacement, thanks.

Quote from: Mike on 02-July-10, 01:31:10
You can go to your local electronics store, even a grocery store(at least in the USA), and get a CR2032 battery. You can use one from just about any supplier with confidence.
I know that. But i want to be sure the battery is suitable before purchasing it and the one on the website is the best example i could find, i am just being careful.

Similar Messages

Multiplier Problem: P35 Neo-F (7360) + e8500 Rev.E0.

Quote from: francis511 on 31-December-08, 02:28:18
I bought an e8500 (eo stepping) and the 9.5 multiplier option is unavailable in the bios of my board. I am running bios 1.9 and neither it nor 1.1a solved this problem. When I tried bios 1.8 , the board refused to boot until I swapped back to another chip.
I have the same problem with a P35 Neo-F (7360) whith a e8500 Rev.E0.
Initially, with native bios v1.7, after assembled the system, it doesn't come ever at the bios . It crashes at splash screen (no Bios, no F11 choice).
I make a update of bios with a "desperate" Ctrl+home at version 1.9, but the bios give a "Cmos checksum error".
However, I succeed to installed the s.o. (win xp sp2) and finally I succeed to flash the bios by usb device.
Now, i enable EIST through the control panel->Minimal Power Management but the multiplier don't increase over 9x in the bios options.
How can i do?
Thanks
P.S. I'm sorry for my little english!

Update your BIOS to the latest Version .
>>Use the MSI HQ Forum USB flasher<<

P35 Neo (MS-7360) ver. 1.0 keeps restart

Hello
I have recently problem with that motherboards ...
Problem occured after a year...
Suddenly Pc keeps restart, linux - kernel panic and says "THIS IS NOT A SOFTWARE PROBLEM"
memtest86 - checked, and memory is ok, still tried other memory, test ok, but pc keeps restart when i try to run windows/linux
Tried to swap PSU, video card - same problem.
CPu temperatures are ok (35C idle)
latest bios
I can add that i have like 60 PC with that motherboard.
For now 7 motherboards have same issue.
Pc specs:
core2duo E6550
2x 512 kingson ddr2 667mhz
Msi Radeon 1050
Tried few PSU
Motherboard don't have sign of problems, everything looks fine, condensers ok.
Any ideas?
regards

Quote from: Henry on 21-June-11, 16:25:31
You have ver 1.0 MB, you flashed the wrong BIOS for it. I would assume that is why you are having these issues. Wrong BIOS can have all kinds of problems up to and including a completely dead MB. Fortunately on the MB's you have when you flash the wrong one you are able to reflash with the correct one. You would need to flash the BIOS for the G33 MB which uses the same BIOS that is correct for your MB. I know this for a fact as I had the same MB a couple of years ago.
>> G33 BIOS <<
>> Use the MSI HQ Forum USB flasher <<
Check the BIOS chip, number is on the sticker. Last 3 digits will tell for sure whether you need 2.x or 1.x BIOS Example would be for what I'm sure you have is: 100 = 1.0, 120 = 1.2, 130 =1.3 etc., etc.
thanks for answers but i think i made mistake with my post (was in home when posting and wasn't sure about bios version)
checked it once again and ... you are right, my mb is version 1.0 and i had bios version 1.5 (2007-11-01) on my last motherboard which i try to fix once more time.
I upgraded bios to the latest 1.10 (2008-11-11) but doesn't helped (i tried that with others motherboards w/o result)

P35 Neo - XP Pro install fatal error

Hello
I have partially duplicated my post since the problem is different from the original thread.
But first....
MOBO - P35 Neo - MS-7360
CPU - Intel Core 2 Duo E6750
BIOS - V1.5
MEM - 4 x 1Gb 800Mhz DDR2
HDD - 1 x 250 Gb Maxtor SATA II (I have 2 but only connecting 1 for install.)
VGA - NVidia 8600 GT
PSU - WinPower ATX 600L - 600W max
Optical - Emprex 8x CD/DVDRW
The motherboard package and RAM was bought from Novatech and was tested before I installed it. Full specs can be seen here
http://www.novatech.co.uk/novatech/specpage.html?MBB-P35675,
and I got them to double up on the RAM.
HDD was also from them.
The problem arises after the first phase of the XP PRO install. I have been using a new copy of XP PRO with SP2 to do the install and initailly things go as expected. I format and partition the drive to create a 50Gb drive for the XP install, which happens without incident, then the machine reboots. Following reboot, the Windows XP branded part of the installation begins, with the 'Collecting information', 'Dynamic Update' and the 'Preparing installation' boxes already checked. Below these, it says that 'Setup will complete in approximately :39 minutes'. About 30 secs into this process, a message box comes up with the following;
Fatal Error
An error has been encountered that prevents setup from continuing.
One of the components that Windows needs to continue setup could not be installed.
Incorrect function.
Clicking on the OK box takes you to the logfile, which reads;
Error:
Installation Failed: D:\I386\asms. Error Message : Incorrect function.
Fatal Error:
One of the components that Windows needs to continue setup could not be installed.
Incorrect function.
Pressing OK after this reboots the machine and we go round again.
Things that I have tried to fix this:
1. Removed RAM, tried it with 2 and 1 DIMMs
2. Changed the optical drive.
3. Burned another copy of XP with SP2 at slower speed to ensure it wasn't the CD.
4. Used another HDD with same specs.
5. Scoured these forums and the net to find an answer, but nothing clear cut has arisen. Or have I missed it?
There have been a few threads which mention putting extra drivers into the XP PRO SP2 .iso, but since I am using 1 drive on SATA1 as well as an XP PRO with SP2 disk, this does not appear to be required. I have used the standard settings in the BIOS. Can anyone shine some light on what I am doing wrong?
Thanks for reading!

Sounds like it may be a optical drive or a bad ISO. Seems like people are having issues using Nero and recommend using PowerISO. edit: I noticed you you are using an OEM CD so more than likely either a scratched CD, a bad drive or cable.
Read this: http://www.nocrash.com/ncbbs/msgs/1075.shtml

[SOLVED] P35 Neo - Slow boot

Hi,
On a P35 Neo, the computer takes a lot of time to boot (around 2mn to see the windows logo indicating that the OS is starting). When the windows logo appears, the start up times is normal.
It seems that it takes times to check devices then it's ok
I've checked my devices (hdd, mermory ..) no problems detected. May be a bios config.
Any help is welcome
Thanks
Config
Motherboard: MSI P35 Neo MS-7360
CPU: Core2 E7400
Memory: 2x 2Gb Corsair XMS2
PSU: Cosair TX750W
Video: MSI N260GTX (GForce GTX 260)
Drives: WD HDD 160Gb SATA, Samsung DVD player SATA

2 minutes is a lot of time for window to appear??
are memories in slot1 and slot3 ??
what is your bios latest or the first bios.
if memories in slot1&3 then go into bios then default setting click on it then click yes then save and exit then test.
if prob still persist then as wonka has suggested strip to bear, test, then add one hardware then test start time..and so on, from this you should be able to identify the hardware which is causing it.
if prob persist your last option is flashing bios safely

P35 Neo strangenesses at inclusion

MSI P35 Neo (MS-7360) Bios v1.2
Core 2 Duo E6420, 2133 MHz
GeIL DDR2-800 2x1024 (5-5-5-18(CL-RCD-RP-RAS)/23-42-3-6-3-3(RC-RFC-RRD-WR-WTR-RTP))
Video Asus EN8800GTS 320MB
2xHDD WD1600YS-01SHB1
Motheboard, аt start of system, before passage POST (about 1-2 seconds after inclusion) it is reloaded,
then start and it is normal work. As it to correct?
Excuse for my bad English.

Quote from: Frankenputer on 05-August-07, 09:38:41
Holy CRAP!!!! 16A on the +12V rail...That's likely your issue. You really need a PSU with at least 30A on a single +12Vrail PSU, or, for a multi-rail PSU, 19A on each +12V rail(20+A/rail is better(remember, this is for a multi-rail PSU)). You need to get a better PSU.
Help to choose:
CHIEFTEC 500W (CFT-500-A12S) +5V - 30A; +12V (1) - 11A, +12V (2) - 21A; +12V (3) - 12A, +5VSB - 2A; +3.3V - 28A
HIPER 580W (HNHPU4M580PU) +5V - 36A; +12V (1) - 20A; +12V (2) - 18A; +5VSB - 2.5A; +3.3V - 30A

MSI P35 Neo-F (MS-7360): Computer randomly freezes while playing games

Hi there,
I have reached the end of my technical knowledge right now and I'm not even sure if this area of the forum is appropriate. The problem:
While playing higher-end games like Crysis 2, Anno 1404, Mass Effect 2 etc. my computer randomly freezes and the last few milliseconds of sound are being looped on my speakers (kind of like a buzzing sound).
By "freezing" I mean that my computer becomes unresponsive to any action other than pressing the Reset-Button or holding down the Power-Up-Button (no reaction to Ctrl+Alt+Del, Alt+F4, Alt+Tab, no mouse movement... you get it).
There's no exact timing as to when these freezes occur. The fastest freeze happened after less than a minute of playing a game, slowes one (just today after switching to my newer case with better cooling) took about 2 hours.
This freeze only occurs while my System is under load. No freezes while browsing the web, using office programs, listening to music or watching videos.
System Specs:
Mainboard: MSI P35 Neo-F (MSI-7360)
CPU: Intel Core2Quad Q6600 @2.4GHz
RAM: 4x 1GB DDR2-800 Corsair XMS2
Graphics: Gainward GeForce GTX 560 Ti, 1GB GDDR5 VRAM
PSU: Antec High Current Gamer 620W (upgraded from Xilence XP600, 600W)
New CPU Cooler: Arctic Freezer 13 Pro (upgraded from OEM Intel Boxed Cooler)
New Case: Zalman Z9 Plus w/ 4x 120 mm Fans (Upgraded from a Case with only 1x 250mm side Fan)
2 Western Digital HDD (1x 2TB, 1x320 GB)
1 DVD Reader/Burner (unimportant for that error I guess)
OS: Windows 7 Ultimate 64-Bit
2 Screens: 1x 24" Asus VS248H and 1x 21" LG Flatron Wide W2240T
Since this error is bugging me for quite a while now and since this is not the first forum I'm trying to get help from, here's a list of steps i already took to get rid of it, obviously to no good use:
reinstalled games where the freeze occurred
updated all Drivers (including cleaning old versions in safe mode; also tried older drivers)
updated BIOS to v1.A0
Reinstalled Windows
bought new Case and CPU Cooler to improve Air Flow/Cooling
checked Seating of all components (took out, cleaned, reapplied thermal grease where neccessary, re-inserted)
cleaned old case of dust (obviously no problem in the new case, which is 2 days "old")
ran 7 sequences of Memtes86+ without any errors
ran Prime95 without any errors for about 45 Minutes
ran Furmark for 15 Minutes under full load (burn-in test) without any problems, even though my graphics card hit the 100°C frequency-cut level
ran Furmark and Prime95 simultaneously without any problems
took records of component temperatures and system voltages without noticing anything unusual (at least not after i switched to the newer PSU, which is about 1 Month old - yet didn't resolve the problem)
tested with cyclic removal of 1 RAM device to further rule out RAM malfunction
tested with only 2 RAM devices in dual channel mode (Slots 1 and 3)
tried to reduce RAM clock (800 MHz --> 667 MHz) to no avail
checked S.M.A.R.T. values of HDDs, no issues reported
tested without any background programs
raised/lowered voltages to RAM, CPU and Chipset in BIOS to increase logic circuit stability/decrease heat production
I need to mention: After I transferred my system to the new case, i was able to play longer than average compared to my old case. So I am guessing that improper cooling was part of the problem, yet improving cooling obviously didn't resolve it.
Since these freezes are really annoying and nobody could help me resolve this so far, I'm hoping to find some new ways of narrowing down the problem or even getting rid of it here.
Regards
Sebb

Quote from: Bernhard on 10-July-12, 13:15:30
Lets be realistic. A system with a 560TI is recommended to have a around 31Amps under full load, a CX500 would be sufficient.
Have you monitored your CPU and memory utilisation ?
As suggested before, test the GPU in another computer to see if the behaviour is the same.
Whew, I thought for a second there that my common sense had left me when I saw that 60-Amp-Post ^^
Yes, I monitored CPU and RAM usage, there is no recognizeable pattern to be seen and it almost never happens under full load.
I will see if a friend of mine can test my GPU on his computer, and I will test it underclocked right away.
Though one more question regarding that: Should I only underclock GPU Core Clock or both Core and RAM clock?

Ms-7360 P35 Neo wo't boot with full 8GB DDR2

Let's begin with me stating my problem:
I recently bought these ddr2 modules: http://www.ocztechnology.com/products/memory/ocz_ddr2_pc2_6400_vista_performance_gold_4gb_dual_channel (2x2GB OCZ Gold PC2-6400)
I already had 2x2gb Patriot ddr2 (http://www.patriotmemory.com/products/detailp.jsp?prodline=5&catid=2&prodgroupid=38&id=658&type=1) installed on my mainboard (ms-7360 P35 Neo).
Now i can't boot Windows 7 64-bit with the full 8GB memory, it gives a blue screen or just keeps looping the boot sequence. If i use 6 GB my rig works, but is still a bit unstable.
I have tried placing the new memory modules in another rig and they work. I also tried swapping the modules:
A1 + B1: Patriot memory
A2 + B2: OCZ memory ---> doesn't work, turn out in a blue screen
A1 + B1: OCZ memory
A2 + B2: Patriot memory --> this doesn't work, because i it has something to do with BIOS remembering previous setup.
A1 + B1: Patriot Memory
A2: OCZ memory module 1 --> works, but when i was loading files to a separate hdd i got the blue screen.
A1 + B1: Patriot Memory
A2: OCZ memory module 2 --> works too, but like above it's only 6GB and i want the full 8GB.
A1 + B1: Patriot Memory
B2: OCZ memory module 1 --> works
A1 + B1:Patriot Memory
B2: OCZ memory module 2 --> works
Oh, i almost forgot to say this: During the boot i also see that, when all 4 slots are full, i see 8GB
Now if anyone can help me get the full 8GB working, I'd be a very happy person

Get all 4 matching modules. It works when you have 3 of them installed because they would be in single channel mode and single channel can tolerate miss-matched RAM much better than dual channel can. 2.2V Patriot 4-4-4-12, 1.8V OCZ CL 5-5-5-18

Please to help rookie with quad core on P35 Neo 2 (MS-7345)

I bought a home built computer (specs below) for my sons almost a year ago and have had nothing but trouble with it. After I finally realized that the graphics card was over-heating it worked better for a bit after replacing Radeon 9600 with some crappy one. Then I reinstalled XP and seem to have lost drivers for some of the functions of the MB like sound and networking. Presently it is an impressive looking paperweight with fantastic specs.
It does boot to XP and has internet connection now that I stuck in a NIC card.
I was foolish enough to install and run microsoft genuine advantage and, because it didn't pass, have to read about it every boot and login. So I'd like to reinstall XP again.
I do have System info for Windows (SIW) installed.
I bought system so sons could play Call of Duty 4. When I try to launch COD it gives message:
"Error during initialization:
Miles sound system initialization failed.
Make sure you have your sound card's latest drivers and DirectX installed."
I have installed latest DirectX but do not know what to do about sound card as it is function of MB, I think.
Any help would be greatly appreciated as to next steps or what further info I would need to gather to solve.
Thank you!
Chip
Specs:
-Intel Quad Core CPU Q6600 clocked @ 3.0 GHz x 4, passed 24 hrs Prime95, 100% stable
-Copper Heatpipe CPU Cooler for better cooling than stock heatsink
-MSI P35 Neo 2 motherboard with Intel P35 Chipset w/ Intel ICH9R Chip, Copper Heat-pipes to keep both the chipset and power converter cool, Socket 775, FSB 1600/1333/1066/800-MHz, and,
-Dual 16x PCI-Express video, (4) memory slots for up to 8 Gigs of Dual Channel DDR2-1066 memory, (5) SATA connectors, (2) external e'Sata ports, up to (12) USB ports, CrossFire Support
-2-Gigs of CORSAIR XMS2 memory with with DHX Technology DDR2-6400 (800-MHz) for best Vista performance.
-Seagate 1TB, 32-Meg Cache, 7200 RPM hard drive with perpendicular recording technology for great performance
-HP 20x Dual Layer DVD / CD-RW Burner to handle all your burning needs
-Gigabyte 10/100/1000 Fast Ethernet Port to connect to your High-Speed Internet
-(8) 2.0-USB ports to connect digital cameras, printers, MP3 players, etc… (6) in the rear and two on the front
-7.1 HD Surround Sound Audio
-Dual boot of XP and Vista, along with Photoshop and Office included .
-Sigma "La Vie", black gaming case that has a side window and Blue LED fans to show off the parts. Along with a 680W power supply 30-Amp 12V rails, 6-pin PCI-E power connector give this plenty of juice for any video card.

Thank you again for that page. I had looked (in vain) for this because I did not receive the MSI cd with this computer.
http://www.msi.com/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=1213
I dl'd all of the files and began to install from the bottom up. The "Intel INF Drivers for 3/4/5 Chipsets" went fine but in the 'read me' for "Intel Matrix Storage Manager Driver" it says that if none of the supported RAID or SCSI controllers are present in the Device Manager/IDE ATA/ATAPI controllers then your computer is not in RAID, SCSI or AHCI modes and these drivers are not applicable. Does that makes sense considering the type of hard drive? Do hard drives have drivers? (apologies if this does not make sense)
Also, the "Realtek PCI-E Ethernet Drivers" only contains dll, system and a security catalog file. I do not know what to do with these to install.

P35 Neo-F

Beta BIOS for P35 Neo-F (MS-7360, PCB 1.0) BIOS ver. V1.1B7
BIOS Sign-on message: A7360IMS V1.1B7 051807 (Date: 05/18/2007)
Attachment name: P35 Neo-F V1.1B7.zip
Make and ensure PC is stable before proceed. Remove any OC if you have it.flash BIOS from USB key, by using our Tool(easy & safe way to flash):
MSI Forum HQ USB Flashing Tool
Use Beta or Modded BIOSes at own risk!

Quote from: uid313 on 07-June-07, 22:05:29
Where is the changelog?
I see no reason to do the risky process of flashing to a new BIOS, especially a beta BIOS, if there is nothing to motivate me why, if there is no reason todo so, what does this version do? What does it improve? What does it change?
There is no descriptions on the Beta versions..

NEED HELP w/ P35 Neo Combo and Windows XP Install Stop 0x24 error BSOD

First a little background, in case it's relevant:
I was running a 865PE Neo2 with 4 x 1gig Corsair DDR2 6400. Otherwise, same specs as below. Ran it for 2 years without a hitch, then got a virus that corrupted my profile and had trouble booting, logging on, and persistent virus messages. Long story short, I fried the BIOS and decided to replace the mobo and upgrade the memory, keeping the rest of the system intact. I previously had windows installed on both partitions of the HDD but changed the name of the directory for Windows on the C: drive so it would boot from the D: drive.
I have replaced 865PE with the P35 and changed the boot sequence to boot from CD. The BIOS loads fine, and I get to the windows setup screen ok. Whether I opt for Recovery Console, or a new install of Windows, I get a BSOD error message below.
STOP: 0x00000024 (0x001902FA, 0xf7906700, 0xf7906400, 0xf7103bef)
ntfs.sys Address F7103BEF base at F709f00, Datestamp 3d6de5c1
I tried with both new and old memory (in the right slots) and get the same message. I booting with no memory because I read in another post that the system should beep to indicate no memory and there was no beep.
BIOS recognizes the HDD, CPU and Memory so not sure what the problem is. Should I try taking the HDD out and reformatting it on another PC? (not easy since I don't have another desktop pc) Please help with some suggestions. Thank you.
System Specs
P35 Neo Combo Mobo
BIOS ver 1.3
E6400 Intel Dual Core
1 x 2 gig Crucial PC3 8500 DDR3 1066 mhz
nVidia 8800 GTS graphics
WD 250 gig Sata HD w/ 2 partitions of 125 ea.
Antec 500W SmartPower PSU
Installation disk is Windows XP Pro sp1

STOP: 0x00000024 indicates corrupt NTFS file system on the hard drive
Reformat would be the best thing to do. Download WD Data Lifeguard for your HDD, make the disk and run it.
http://support.wdc.com/product/download.asp?level1=6&lang=en
Quote from: FlyingSteve on 18-August-09, 10:29:00
I didn't know that the P35 Neo board ran ddr3...
That's where the 'Combo' part in the name comes into play, 2 DDR2 or 2 DDR3.
From MSI description of MB:
Main Memory
• Supports two unbuffered DIMM of 1.8 Volt DDR2 667/800 SDRAM. (Max: 4GB)
• Supports two unbuffered DIMM of 1.5 Volt DDR3 800/1066 SDRAM. (Max: 4GB)

P35 Neo Combo, boot problem? [FIXED]

** PROBLEM SOLVED - Tech support told we that if there was any way to update the BIOS to version 1.3 then I should do that. I found a way and after that everything have been running smoothly.
I would like to thank everyone that helped me in here and hope that my experience and the solution might come in handy to someone else. **
**This thread have been updated with more information and an alteration of the story as my experience with the board/BIOS grew larger, and some information was given to me by at kind person in this thread**
Hello everyone.
Some days ago I got some new hardware and put it all together but I ran into a big problem.
Specs of the new machine:
Case: Arctic Cooling T2 Pro, Miditower, 500W
Psu name: AX-500F, specs:
+12v: 14 A (15 A peak)
+12v2: 16 A (19 A peak)
+5v: 25 A
+2.3v: 30 A
-12v: 0.5 A
+5vSB: 2.0 A (3.0 A peak)
This information is a direct quote from Artic Cooling's homepage:
Power Supply
The AX-500F is a power supply optimized for high end PC's and complies with Intel's ATX12V version 2.0. The continuous output power fulfils gaming system requirements based on multiple VGA boards.
The AX-500F was tested with the following configurations:
AMD Athlon FX-62 CPU
2 GB Ram
2x ATI X1950 XTX (Cross Fire)
Intel Core 2 Extreme CPU
2 GB Ram
2x NVIDIA 7950 Gx2
I also did try booting with a more powerful PSU but still no luck, and from what I can see then this one should be powerful enough
Mobo: MSI P35-NEO-Combo-F, Intel P35, Ver. 1.0, BIOS ver. 1.2
CPU: Intel Core 2 Duo E6750, BOX
Ram: Corsair TWIN2X2048-6400C4, 2x1024MB 2.1v
Graphics card: Inno3D GeForce 8800GTS, 320MB, PCI-E
CD-rom: Lite-On DVD/CD
HDD: Western Digital Raptor 74GB
OS: Windows XP 32bit
When I turned it on for the first time nothing happend, no picture no error sounds although I could see and hear that the computer was on. I turned it off and then on again, nothing, I turned it off and then on again and something happend.
I got a red text message saying that my overclocking attempt was unsuccessful, which I found pretty odd cause this was the first time the computer was on. I have now been informed that it's a fail safe build into the BIOS to prevent a melt down if you overclock it too hard, which is kinda smart. I then had the option to go into the BIOS, so I looked at every setting to see if things were OK and if it was somehow overclocked or had some wrong settings.. Everything looked and still looks alright when I save and exit. When I do save and exit, be it with the settings I think is okay, the fail safe or optimized settings then the screen just goes black.
So now for the 'clearing the CMOS' part When I reset the CMOS with the jumper I can get further than the error message about overclocking. I get two options:
1. To enter BIOS setup to configure the bios.
2. To automatically load some default settings and continue booting.
First I tried option 1, after doing a save and exit the screen went black again, got the overclocking message and had to clear the CMOS one more time.
Then I choose option 2, windows started to load, I got into safe mode and windows started to find all the new hardware and so on. When that was done I was kinda forced to reboot, screen went back and yes you guessed it... I had to clear the CMOS and choose options 2. I got as far as getting into windows and installed some of the stuff from the CD-rom's that came with the motherboard, again I was doomed to reboot and clear the CMOS. Once again option 2 needed to be selected to get the system up and running, and I got as far as to the "Want to activate windows" option, and couldn't do that cause the network card was not installed so I had no internet connectivity. Apparently if windows detect too much hardware being replaced then the activation thing pops up, and I later learned that I can't activate my windows anymore cause I used my activation quota and I have to get a new key
What I learned from my brief time in windows normal mode:
Everything seemed to work nicely, and freaking fast too....swiiing!
2gb of ram was detected, running dual channel and at the desired voltage.
The CPU was running at normal speed and voltage.
All in all everything seemed normal until I rebooted.
The only thing I can conclude is that something goes horribly wrong when I clear the CMOS, load some default settings and then reboot. I have seen that I am able to get into the system with my current hardware, but only after a CMOS clear, so what the heck is wrong, what goes wrong after the reboot?
And this is as far as I can get with my own knowledge of computers :(
So now I hope to go that I can get some help from some of you guys, any thoughts on this or anyone know of such a problem and maybe know a solution?
If I missed some information you guys need to solve this puzzle then just ask.
On a side note, if I somehow get the chance to flash my BIOS to version 1.3 in hope that if will solve my problem, then will it erase my chances to send it in for RMA and get a new board? Do I break any rules by doing that?
Best Regards
Mads, Denmark

Quote from: Maesus on 24-August-07, 23:29:25
ok, when you turn it off and on and off and on, the BIOS will think it's an overclocking failure event, and hence display the overclock error message.
usually this is due to the memory settings was set incorrectly (by the BIOS itself). You may need to manually change the memory settings and see if that helps. And, please make sure that your BIOS can support FSB1333 processor like E6750 out of the box. If not, try flashing to the latest BIOS.
Hello and thanks for the quick anwser.
I did check if memory/cpu settings were okay and the seem to be on the right defaut setting. I save and exit and the screen just goes black. I forgot to add the motherboard and BIOS versions but they are there now: Mobo: MSI P35-NEO-Combo-F, Intel P35, Ver. 1.0, BIOS ver. 1.2
I don't see how I will be able to flash the bios when I can't get into windows and do it, and there is no way else for me to do it. If it was the case that the BIOS didn't support FSB1333, then I would never have gotten as far as getting into windows and getting the activation message would I?

Strange problem with P35 Neo

Hi there.
Got a strange problem with a computer that got a P35 Neo system board.
The problem I got, is that the computer don't boot. If I reset the CMOS,
I can get the computer to boot, but then it hungs on loading Vista.
Then I try to repair my Vista. Then the computer hungs while loading the DVD.
I have tried to boot with only one RAM in the computer, but the problem still
there...
I have tried to reset the CMOS by changing the JPBAT (I think it called so) jumper
and to pull out the battery.
I have tried to disconnect all, but one HDD and but I can't say that it worked any
better...
Any ideas how to find out the error?
2 x 2 GB Corsair RAM
Intel dual Core CPU
Radeon 1950 PCI-E
1 Samsung SATA HDD
2 Seagate SATA HDD

Quote from: BOSSKILLER on 25-August-08, 20:31:15
What PSU you have? Corsair Powersupply 550W Black, ATX/EPS
Provide better details about memory sticks used. Corsair TWIN2X 6400C4DHX DDR2
What CPU? Intel Core 2 Quad Q6600 2.4 GHz
BIOS version onboard? Note sure, since I'm not right at the computer for the moment. But I think it's 1.0 since it is brand new from store.
Do memory check with >>Memtest86<< Well, it's kind of difficult, since the computer dont boot.

MotherBoard Warranty (p35 neo-3)

just a little question ,replacing the chip-set heat-sink (north bridge)will void the board warranty?
im experiencing a very weird problem that i couldn't find any solution
any hard-disk even a brand new one will keep getting pending sectors using this board and im going to send it for warranty
i replace the chip-set heatsink with a aftermarket one and i lost the original
but i have an old heatsink that looks the same with the original but the problem is it doesn't have the foil under the heat-sink ( the original one have)
if i send this board with its north-bridge heat-sink different will it be denied for warranty?
specs are
P35 neo 3 -f
Q9300 processor
4gb team Elite ddr2-800 rams
msi hd4670 Graphics Card
1tb hd103sj Hard Drive
(got 500 gb seagate and 640 gb western drive and still the same problems keep getting pending sectors)
Windows xp X64

yes windows is very slow and having too many lockups but no blue-screens
first the 500 gb sea-gate drive stuttering problems even playing video (because of too many read errors per second. i clone my windows partition to my western digital drive stuttering problems gone but after 1 week of using it as system drive it shows 137 relocated sectors count and i asked for drive replacement and the same problem after the replacement drive is unstable few days relocated sector count starts to rise ,last my 1tb Samsung drive its 3 months as a data backup drive with no problem but again i cloned my windows partition there hoping the problem will be solved but after exactly 5 days of usage drive starting to have lockups windows freeze for few seconds and hdtune showing pending sectors count
i really dont understand why every disk that i connect to system becomes unstable

P35 neo + q9550 problems

I've just upgraded my one-year-old PC with a new CPU and additional memory. I flashed my old BIOS 1.7 to the newest 7360v20 version, which should support Q9550.
However I can't boot up normally (even to POST) and have to keep trying five times (in order to get the "BIOS settings resetted" -message). The only way to boot seems to be the following: In the resetted BIOS settings menu, I choose to load fail-safe options and DO NOT save the BIOS settings. If I save the BIOS settings, the PC restarts and I'm stuck in the beginning - not getting booted even to POST.
The processor is nicely recognized by BIOS, when I finally get there. When I get booted my OS (winXP 32-bit) seems to run fine and stable (over 100 hours up and running now). However, when I try to watch 1080p video or extract large archives, my CPU slows down remarkably (1080p just doesn't run and extracting takes ages). Basically, I cannot do anything CPU costing. I'm not feeling any other differences. The temperatures seem normal and I don't get any blue screens whatsoever.
I can think of only the following explanations
- My CPU is not supported (my Q9550 is s-spec SLB8V). However, my system had the same boot-up problems with the older E8400 after flashing the BIOS, so that doesn't seem to be the case.
- My BIOS somehow isn't correctly flashed, doesn't actually support the CPU, or some old settings bug it. I've dropped the BIOS battery out a couple of times to be sure.
- My PSU can't somehow keep up
ATM my specs are:
MSI p35 neo(-f) motherboard
Intel Core 2 Quad Q9550 s-spec SLB8V CPU
2x Corsair Twin2X 1024MB DDR2 800Mhz + 1x Kingston HyperX 2048MB 800MHZ DDR2 memory
MSI N9600GT-T2D512-OC GPU
a cheap-ass PSU with 450W and 12V/18A, 5V/14A, 3,3V/18A
The only hardware changes are the processor and and additional Kingston RAM
The power consumption changes are:
Intel c2d E8400 TDP 65W (old cpu)
Intel c2d Q9550 TDP 95W (new cpu)

Quote
but I get only 8x 333mhz = 2,66ghz
If you enable EIST in BIOS, the multiplier should be automatically set to x8.5. As far as I know, this bug only exists if EIST is disabled in BIOS. In any case, the problem should be fixed once you flash the latest A7360IMS.1A0 release for your board. Just make sure that your system is entirely stable before you think about flashing.
http://download1.msi.com/files/downloads/bos_exe/7360v1A.zip
>>Use the MSI HQ Forum USB flasher<<
Quote
a cheap-ass PSU with 450W and 12V/18A, 5V/14A, 3,3V/18A
Invest in a better PSU as well. Yours does not look very convincing (for comparison: a Corsair VX450 PSU with the same overall wattage can deliver 33A@12V, 20@5V and 20A@3,3V ).
Quote
(ddr2 @ 667mhz)
How come your memory is running @DDR2-667? Can you post a screenshot of the CPU-Z SPD view for each of your modules?
Quote
2x Corsair Twin2X 1024MB DDR2 800Mhz + 1x Kingston HyperX 2048MB 800MHZ DDR2 memory
Mixing different memory modules is also not a very good idea as it can cause problems of its own.

P35 NEO MS-7360 Replacement Battery

Similar Messages

Maybe you are looking for