P35 Neo ram problems. Does not boot with 4 sticks

Greetings!
This thread is little related to: https://forum-en.msi.com/index.php?topic=110095.0
Okey so I bought this rig last friday(will post specs later). 4x 1gb ram sticks, shows up as 3.3gb. Was gona install 64-bit Vista today, but got some problems.
I left my computer on during night just to check if it runs fine. I wake up around 6am, turn power on to my monitor. Screensaver, move mouse, desktop and BOOM: Bluescreen(something about memory). Ok so I shutdown my comp, try to reboot got no signal. Removed 2 ram sticks(A2,B2) and yey it works. I plug them back in and again nothing. I test them 1 by 1 on both of the free slots, no problems detected.
Why won't my P35 Neo boot with 4 gigs of ram? And why did it work for 2days? :P
My guess is that the bios is still not ready yet(using 1.2v).
Specs: OCZ 700W GameXStream, P35 Neo-FI, C2D E6750, 4X PQI 1024Mb DDR800Mhz, Leadtek 8800 Gtx

Quote from: NovJoe on 07-August-07, 10:18:34
If I understand correctly, you are saying that you can install Vista and XP to the system but not able to boot into the OS'es when you have 4GB of RAMs installed?
I would recommend you to test the RAMs with Memtest86.
Yes, I could install Vista and XP just fine. Also at first I could boot them with 4gigs just fine. Now my system won't POST with 4 gigs.
I've tested each one of the ram sticks and they are error free.

Similar Messages

  • K9AGM3-F does not boot with PCIe 4x device in PCIe 16x slot

    K9AGM3-F motherboard does not boot with PCIe 4x Intel PRO/1000 PT dual port network interface card installed into PCIe 16x slot on motherboard. The boot process stops in BIOS screens. The motherboard works flawlessly without this NIC. K9VGM-V + Intel PRO/1000 PT boot successfully. I tried three K9AGM3-F motherboards and two Intel PRO/1000 PT NICs in different combinations, the results are always the same. It appears to be some kind of BIOS problem.

    Quote from: Fredrik Åsenius on 09-April-08, 22:52:27
    Minor point, probably irrelevant: I said you install the driver f i r s t. Then you put the physical card in. 
    The driver is completely irrelevant because the driver is a part of operating system, but as I already wrote before the boot process stops long before the OS start.
    Quote from: Fredrik Åsenius on 09-April-08, 22:52:27
    No stability issues otherwise?
    PSU is always good to know.
    The PSU is irrelevant too because the same NICs work in the PCIe 1x slot of the same motherboard with the same PSU.

  • T60 does not boot with Intel T7600G CPU

    I replaced my Intel Core Duo T2400 with Intel Core 2 Duo T7600G CPU in ThinkPad T60(1951-CTO) laptop. However, laptop does not boot with Intel Core 2 Duo T7600G CPU. It doesn't even complete the POST: https://db.tt/8UL8FlE0 As seen in the video, I plugged in the power adapter at 0:02 and pressed the power button at 0:06. One can hear a little click made by optical device. If I press the power button again at 0:16, this click does not happen. BIOS version is 2.27. I have reset the BIOS settings by disconnecting the CMOS battery, but this didn't help. Once I replace the T7600G with my old T2400 then I'm able to boot the laptop.
    Any ideas what might cause such behavior? Shouldn't there be beep codes in case of CPU issues? What else to try?

    TuuS wrote:
    600X wrote:
    Since you came from a T2400, does your T60 even have a Rev. 3 motherboard? If it does not, then no Core 2 Duo will work, only Core Duo's.
    I don't claim to be the top authority on T60 motherboards, but I believe any will use a Core 2 T7600, 7400, 7200 if the firmware is updated.
    My own experience mirrors what TuuS has stated. I have yet to see a T60/p from any walk of life with a recent BIOS that will bark at a proper Core 2 Duo CPU.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • 2960X-48FPS-L does not boot with IOS 15.2-2E

    Hello,
    i got a bunch of 2960X switches. But some of them do not boot with the new IOS Version. The older 15.0-2 EX do boot.
    Does anybody have a clue why this happens? During the Bootprocess it just stops to load:
    File "flash:/c2960x-universalk9-mz.152-2.E.bin" uncompressed and installed, entry poin0x3000
    executing...
    Loading "flash:/c2960x-universalk9-m
    Thank you for your help.

    On the ones that cannot boot 15.2(2)E, can you break the boot cycle using the "Mode" button?
    If the answer is "yes", then try the following: 
    1.  Copy the IOS BIN file from a working switch to a USB flash drive; 
    2.  In ROMmon, force the switch to boot the IOS from your USB flash drive; 
    3.  If it does not work, try a different IOS, like the EX3 for instance.  Try the same process, boot the BIN from your USB flash drive. 
    4.  If it works, try a different IOS, like EX3, for instance.  Downgrade the IOS from 15.2(2)E to EX3 and see if the switch can boot normally. 
    This exercise will determine where the fault is coming from:  IOS bug or a hardware batch problem.  
    To determine if you'e got a hardware batch problem, you may need to look at the serial number of the switches working and not working.  From left to right, look at the 4th, 5th, 6th and 7th numerals.  This will determine the year and month your appliances were made. 

  • MBP with EFI Problem does not boot

    Hi everyone,
    I have a huge problem with my computer.
    After upgrading my iPhone to iOS 7.1 via iTunes i wanted to disconnect my iPhone from my Mac which produced a beachball. I have almost no beachball issues with my Mac since I upgraded to an SSD. After disconnecting the iPhone (beachball still spinning) my computer froze so I had to push the power button until it shut down immediately. After a restart it used it just minutes and it froze again and showed the beachball again. I shut it down with the long press on the power button again and did this several times, what made the problem even worse. After a few restarts I booted into recovery mode and tested the harddrive with disc utility which found a fail, but couldn't fix it (the fail was something with EFI and it sId it couldn't fix it because it can't work with this file format [filevault encrypted HFS+?]). After a restart my Mac didn't boot (and still doesn't) and just shows a blinking folder with question mark in it.
    Because I have two USB-sticks with OS X on it (1 with lion and 1 with mavericks) I booted with them and tried to install a backup and even tried to install a new copy of OS X, but I doesn't find the SSD to install it on there. Just a recovery partition.
    I have no idea how to fix this without another computer. Maybe I could delete the SSD with another computer, but is there a way to do this with my hardware?
    My system:
    13" MacBook Pro early 2011, Samsung SSD (840 Evo 500 GB), 8 GB RAM. The hole harddrive is encrypted via filevault 2.
    OS: 10.9.2, backup (also encrypted) available.
    I would be very thankful for every help and advice you may have.
    Greetings,
    Jonas

    Hello Jonasschoen,
    As the issue that affects your Macintosh HD is not one that Disk Utility can repair, you'll need to boot to internet recovery (by holding Command + Option + R at startup). Here, you will need to use Disk Utility to repartition your hard drive by changing the Partition Layout to 1 Partition. Once you've set up a functional volume, you should be able to successfully reinstall Mavericks or restore from your backup.
    OS X: About OS X Recovery
    http://support.apple.com/kb/HT4718
    Disk Utility 12.x: Partition a disk
    http://support.apple.com/kb/PH5845
    OS X Mavericks: Recover your entire system
    http://support.apple.com/kb/PH14185
    Cheers,
    Allen

  • P7N2 diamond does not boot with q9450

    I cannot get my new P7N2 diamond to boot, i am using
    q9450 cpu
    2x2gb corsair xms 3 dhx (dual channel in blue slots)
    BFG 9800 GTX
    2X 500 Maxtor sata 2 HD
    2xIDE liteon lightscribe DVDR
    600 watt noisetaker enermax power supply
    It turns on but there is no bios beep.Can hear the noise of the drives spinning up, powering up everything, lights on motherboard are lit and fans spin, but the monitor is not showing any bios reading. I have tried running one stick of ram, resetting cmos, check all cables and plugs, but it just wont post. Could the bios be too early to recognise the intel q9450, otherwise any help would be appreciated.

    Quote from: jjdaly on 18-July-08, 19:56:21
    Wow.  You either build lots of systems, or your expectations are pretty low.  'A fact of system building' should only apply to large OEMs not the home builder doing a like a build a year.  That would be a pretty high rate of failure that any manufacturer should be embarrassed by. 
    I'm curious as an employee of Intel how many folks have had issues with Intel branded boards?  I know that we tend to build systems that are less enthusiast-friendly than other manufacturers, but if it's enthusiast-friendly and doesn't work what good is it?
    I have built loads of systems and I still do. I've had my share of doa hardware. It's not an everyday occurance but it happens. A build a year? I've built 8 so far this year and of those I've had one no post mobo (XFX 790i), a bad ram kit, 1 vid card with memory artifacting, a Q9550 (oem) that died a sudden death during testing, and a failed psu. That last item was my fault for skimping. I just know it happens and I don't waste time stressing about it, I rma and get on with it. I like happy endings so I don't sit in the problem, I resolve it. How many folks have had issues with intel branded boards? I'm not sure where you're going with this but I'm guessing intel's numbers aren't much different than MSI's or anyone else's when it comes to percentages. Like any other manufacturing process, it's a given that there will be faulty parts shipped.

  • Am using firefox 5 and am not able of uploading any file as attachmenet using my Yahoo email account , this problem does not happen with hotmail account or when using IE.

    when sending email through yahoo account , i cant upload any attachment with email, a sign of uploading lasts forever without uploading the file.
    this issue do not happen with hotmail account or when using IE to browse Yahoo account.

    Install ClamXav and run a scan with that. It should pick up any trojans.   
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

  • New iMac: 4GB RAM upgrade does not boot

    I have a new 24" 2.8GHz Intel Core 2 Extreme iMac. Bought the Crucial 4GB kit. Installed both sticks, but the iMac would not boot. I heard the hard drive spinning, but it would not boot. I removed a stick from the first slot ("first" from left to right looking at the screen), and inserted the 1GB oem stick. It booted fine. I thought I had a DOA 2GB stick, so I returned it to Crucial. Got my new replacement memory and tried again. Still would not boot. Switched slots. Same problem. Replaced the OEM 1GB in the first slot again, it it booted fine. I tried every configuration, and the only thing that works is the 1GB OEM in the first slot and one 2GB Crucial stick in the second slot. I cannot get 4GB of RAM to work. Any suggestions?

    With the orginal 1GB and a 2GB module installed are you seeing all 3GB in "Apple / About This Mac" and Reading system memory usage in Activity Monitor?
    Resetting the PRAM can solve certain startup problems.
    Try installing the 2x2GB kit and restart the Mac immediately press Command-option-P-R and hold the keys down until the Mac chimes a second time. This resets the information in the Mac’s parameter RAM (PRAM) to its default values. The PRAM is a special area of RAM where data is retained even after you shut down the Mac.

  • K8t neo far-2 does not boot. fans work.

    Hi all,
    I have been reading the post about this motherboard not posting and simular problems with these boards but mabey mine is a little different. Here is what I have:
    - Thermaltake Tsunami dream
    - Antec True 550 eps12 volt
    - Amd Opteron 244 cpu in slot one.
    - Kingston ram KVR333X72Rc2/512 registered ram.
    - Gigabit gforce fx5900xt vidio card
    When I finally got the vidio card installed it and powered up the pc. Did not post or no audio beeps from the speaker. Tried switchin ram slots with this single stick of ram and tried a pci vidio card cannot get vidio/audio post or beeps.
    I have taken out all the drives to minimize this system to its bare essentials to isolate the problem.
    All I get is the cpu,case and power supply fans that come on and thats it.
    I read in the post that the not hooking up the 4 pin molex from the eps12 volt to the Jpwr2 is not to be done as this actuall supplies power to the vidio card? Doing so would fry the motherboard? If so then why does my vidio card have the traditional molex connector on it as seen on hard drives? it does not match the one on the motherboard. 2. If that square white semi clear four pin connector from the eps ps does not go into that jpwr2 jack on the motherboard then what does it go to???
    Are there bios test LEDS on this motherboard? I dont see any.
    Lastly I hear a faint click every 10 second on the pc speaker but no bios codes.
    You help is much appriciated to rectify this problem.
    James

    In dont want to except this as a blown board. I dont have any warentee on this mothetboard as it was purchaced though a second party.
    If by chance placing the 4 pin molex power cable comming from this power supply into the four pin connector on the motherboard "IEEE is going to hear about this" and it did fry the mothboard would it also fry the cpu and ram? I HOPE NOT what have you heard from other people?
    Bas, read compatibility list about ram and the kingston ram I should be using.
    While this list did not include my ram it should work right?
    My ram may be a little faster but it is ECC. The ram I ordered was specificially ECC kingston ram from compucare and it should work. The ram model number is
    KVR333X72RC25/512
    Also, the power supply is a Antec True 550 EPS12V
    The power supply specs are as follows:
    DC output  +5V    +12V     +3.3V     -5V     -12V     +5V SB
    MAX.          40A    36A        32A       .5A      1.0A      2.0A
    Min.            0A      0.8A       0A         0A      0A         0A
    Now Even with the cpu and memory taken out there should be some post beeps on the speaker? I dont think I have done this yet.
    Lorin

  • 24" iMac AlSiO does not boot with iPod video on USB dock

    Hello all,
    I have already reported this as an issue with Apple.
    I noticed that when I turn on my new iMac with the video iPod on the dock connected via USB, I only see the gray screen and the OS does not start. However, once I remove the iPod from the dock, then the Apple logo will show up, and the circular moving tiny line counters will ensue before the login screen appears.
    Just wondering if anyone else is running into this problem.

    Thanks for the suggestions den.thed and elmac.
    I have done the following:
    - Selected the Mac OS X on the MacHD as the startup disk and locked that from further changes. Restarting the iMac did not work.
    - Verified and repaired permissions. Restarted the iMac and it did not work either.
    In addition, I also tried:
    - Restoring the video iPod and leaving it without contents. Rebooting the iMac worked.
    - Syncing iTunes with the iPod after the restore. The rebooting problem appears again.
    It seems like some synced items on the iPod are causing the issue as odd as that sounds.
    I did not have this problem with my G5 iMac.
    Since there is a workaround, I'll just live with that for now.
    Thanks again.

  • PC does not boot with Ipod Nano

    My configuration:
    Shuttle SK83G, Athlon64 3000, Windows XP Pro, Logitech DiNovo wireless desktop.
    My problem:
    If my Ipod Nano is connected the PC will not boot. The bios screen shows up and then nothing happens. I even can not access the bios. If I remove the ipod the PC will eventually start windows. But in absolute slow motion (I can see how the Windows startup screen fades in step by step).
    If I connect my Nano after booting, everything is perfectly fine. Also with my Ipod Mini connected, the PC boots up without a problem.

    it's not just a Nano problem, but a USB port problem
    That's correct. USB is famous for this. Something in the BIOS (probably) is telling it to try and boot from the nano, but of course it can't find a valid OS there. And the solution is just what you suggested. Don't boot with the nano connected.

  • P67A-GD65 does not boot with LSI 9240-8i HBA

    Hi All,
    When I installed my LSI 9240-8i I was able to boot to the ICH10 Raid as long as the Marvell Raid controller was disabled.  Once I updated the LSI card to the latest version of the firmware I cant boot at all.  I've cleared the CMOS, I've disabled everything in the BIOS (raid controllers, 1394, NIC, etc).  All not no avail. 
    Thus Far I've tried:
    -Booting to OS on the ICH10 RAID gets me into Windows 7 (x64): Resulted in the LSI controller showing, "This device could not start. (Code 10)" under Device Manager.
    -Updating Firmware: Resulted in the mobo hanging on POST at code "92".
    -Upating BIOS from 1.B to 1.C5 Beta: Resulted in mobo hanging on POST at code "92".
    -When I move the card to my Dell Prescision workstation, the LSI RAID controller works like a charm!
    Observations:
    MSI P67A-GD65 BIOS v. 1.B
    -LSI Firmware
    20.10.1-0037 (APP-2.120.54-1235)   15-APR-11   - BROKEN
    20.10.1-0029 (APP-2.120.24-1181)   - 04-MAR-11 - BROKEN   
    (Same as above, but I list it anyways)
    MSI P67A-GD65 BIOS v. 1.C5
    -LSI Firmware
    20.10.1-0037 (APP-2.120.54-1235)   15-APR-11   - BROKEN
    20.10.1-0029 (APP-2.120.24-1181)   - 04-MAR-11 - BROKEN   
    MSI PLEASE HELP!
    I am running:
    Mobo: MSI P67A-GD65 1.C5
    CPU: I7 2600k
    RAID: LSI 9240-8i
    Thanks!

    Quote from: NovJoe on 23-May-11, 10:16:19
    Looks to me that it is the LSI firmware issue as the card works fine until you updated its firmware.
    Do card with the card's vendor.
    Hi NovJoe,
    Thats just it.  It looks like its an MSI BIOS compatability issue all along.  Before I upgrade the firmware, the card works in my Dell Precision Workstation, but does not work on the MSI mobo; shows Device could not start (Code 10) error.  After I upgrade the Firmware, the MSI mobo will not POST, but the Dell still boots up with the card perfectly.
    Its definitely NOT the card.  If both the 9240 and 9260 cards work perfectly in other computers then there is something wrong with the MSI mobo or BIOS.
    Please help. 
    Thanks!

  • Logic midi exporting problems (does not work with cubase)

    ok so there is an audio file i need converter to midi for something i'm working on someone with who uses cubase...
    so basically an audio file from cubase needs audio to midi. since cubase does not have this feature i imported the .aif file from the cubase project and used audio to score to extract midi. i then exported the midi file and imported it back into the cubase project and it was not aligning with the audio file.
    note that the cubase project has variable tempos but i imported the file into default tempo and extracted the midi in the default tempo mode. but this shouldn't be a factor since midi conforms to current tempo so when it gets reimported back into cubase it should sync with the project tempo there....
    can anyone help???

    Hi
    Diogo Colaço wrote:
    Already tried with different keyboard and I have find out that the keyboard that I use at home only sends midi via channel 4...
    You have a couple of choices:
    Within the EVB, change the Keyboard Mode to single. You may need to do this a couple of times to get it to work. You would also need to do this for every EVB preset that you use
    You could setup the organ Instrument Channel Strips as "Multi-Timbral" with the incoming MIDI mapped to Channel 1. You would need to do this for every Organ Strip that you want to use in your MS Concert.
    CCT

  • Securing old 10.4 xserve with hot spare - new xserve does not boot with 10.

    dear you,
    I am in the murky situation of having to secure a single, non redundant productive scenario which is running on one xserve (model identifier 1,1; dual core 3GHz; boot-rom XS11.0080.B00). due to several reasons the server needs to be cloned, so that a separate xserve with a daily cloned boot-device can take over if things go south with the productive one.
    unfortunately the newly bought xserve quadcore single 2.26GHz refuses to boot from the image taken from the production machine. tried to downgrade firmware, did not help. new machine crashes during startup (empty grey screen).
    anybody knows any help? moving the production machine to 10.5 or newer is NO option.
    an option could be two elder xserves I have here additionally. how do I find out which xserve model will boot with an image from the production server?
    thank you all for any idea in advance,
    thaijay
    Message was edited by: thaijay
    Sorry, failed to let you know the productive server is running 10.4.11. please let me know which other details I can post/will help us with this issue

    This is never going to work via cloning.
    The server you're cloning has to be one of the original Intel-based XServes. Each successive revision adds requirements to the OS to the point where they have a minimum OS version. In the case of the latest generation servers, they won't run on anything earlier than 10.5.6 (IIRC). To put it simply - 10.4 doesn't know how to drive the latest generation hardware.
    In any case, cloning is rarely a good idea for servers anyway. You would do better to look at the services you're running and look at backup/failover plans for them rather than trying to clone the entire server. Many services such as Open Directory, DNS, MySQL and more have built-in replication systems that are designed to replicate their data across many machines. Other client-facing services such as AFP, web, FTP, etc. can be set to failover (where the second machine takes over the service when the primary machine fails).
    Such replication/failover techniques are far more reliable than a daily clone, and they're also faster. Replicated data could be maintained up to the minute, compared to a day old data if you need to boot up the clone.
    If you really, really want to go the clone route, then reverse the roles - setup the new machine as the primary server with all the services and clone this machine to create your failover system. 10.5.6 will run the old/original XServe, it's just a matter of updating your services to the newer version.

  • HPE-510t does not boot with AMD FirePro W5000 (Windows 8.1)

    I just purchased an AMD FirePro W5000 (TDP = 75 W) to replace my nVidia Quadro 600 (TDP = 40 W) in my 2011 HPE-510t (i7-2600, 12 GB RAM). Dell U2913WM monitor.
    My machine will not start with the new card inserted. I upgraded the stock 300 W power supply to a 450 W Antec VP450F, but that didn't change  the startup situation. I tried DisplayPort and Dual-Link DVI-D.
    Anyone been able to get the AMD FirePro working in an HP desktop of this generation?
    Thanks,
    Mike
    This question was solved.
    View Solution.

    Hi Mike,
    I am glad that you finally have success.  The issue is probably that the PC BIOS level is too low.
    The passmark numbers look very good.
    BTW -- I had the ASUS P8P67 motherboard and donated it another forum member. It wouldn't support an EVGA UEFI BIOS based graphics card. I ended up replacing the ASUS P8P67 with the ASUS Z87.
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

Maybe you are looking for