P35 platinum bios update query

just updated bios from 1.1 to 1.4 and now lan stays active when pc is shutdown...now under 1.1 the lans only became active once windows was up an running and all lights on router went out on shutdown has anyone else seen this behviour.alos this updated bios removes some of the options is there an f key ican press to get to a advanced bios state

There are a few reasons I guess.  One of the key is the Wake on LAN. Trying turning this option off in bios to see if your lan light go off on shutdown. But this is very common in most PCs. Give it a shot and let me know how it goes.
Regards,
Sailendran Iswara Jothi

Similar Messages

  • MOVED: K8N NEO Platinum Bios Update - Memory Downgrade

    This topic has been moved to AMD64 nVidia Based board.
    K8N NEO Platinum Bios Update - Memory Downgrade

    just switch back to bios 1.7

  • P35 Platinum + BIOS issue?

    Hi,
    Today I updated the BIOS for my P35 to 1.3 through Windows. Everything seemed to go OK but as the system rebooted it never came back to life. The D-LEDs indicate "Memory DecetionFail" however the system was working just fine before the flash.
    The ram i'm using is "Corsair XMS2 6400C4".
    Rest of the system is:
    -P35 Platinum
    -E6750
    -Above mentioned ram in 2 x 1GB
    -GF 7900GT
    -Creative X-Fi
    -Antec NeoHE 550W
    Any ideas? Try to find a floppy and reflash back to 1.1?

    Quote from: qyx on 26-August-07, 00:28:14
    Try clearing cmos carefully (with power cord disconnected) as described in the manual.  Then try it with battery removed and letting machine sit for at least 30 minutes before restoring jumper to original position, closing case and reconnecting powercord.  Windows flashing can be quite risky as you just learned.  If cmos clear does not work, you should reflash back to the last bios that worked (see other threads for right way to flash).  Good luck
    Thanks for the tip i tried to clear the CMOS right away but it didn't do anything...i've since read that there are some issues with the 1.3 bios and CL4 ram and i'm going to get some ordinary CL5 DDR2-667 ram tomorrow and will try to boot to see if that does it..
    The reason i did the Windows update thing is that i have no floppy so will have to get me one of those as well tomorrow to make sure that I can reflash to 1.1 if indeed the BIOS is corrupt due to the Windows update.

  • P35 Platinum bios ver 1.5

    Hi !
    I have updated my bios to 1.5 from 1.0 and the reason for doing this is i had alot of problems with my raid 0 setup.
    Now to the problem I am able to boot my pc and get into the bios i even get windows up and running, but my pc hangs for about 3 mins trying to interlize the marvell controller.
    Can anyone give me a sugguestion on how to fix this problem.
    Regards
    / Leif

    # CPU "Intel Dual core 2.4"
    # Motherboard model "P35 platinum"
    # Memory brand, "Corsair XMS Xtreme 800 MHz 4-4-4-12 4gig"
    # Video card brand, Asus GTX 8800 764 meg
    # Hard drive(s) brand, size, type, speed "2x Seagate 320GB in a stripe raid"
    # Any other peripheral cards and devices "soundblaster XF music"
    # Operating system and version "Microsoft Vista"
    # Power Supply Unit "Zalman 600 -HP 600 Watt"
    I hope this will give you the information you need to help me out.

  • P35 Platinum - BIOS 1.C

    Anyone had/seen complaints about not being able to install their OS with BIOS 1.C on a P35 Platinum?
    I've verified it's not the optical media, multiple versions/discs of Windows fail.
    I've verified it's not the optical drive, internal and USB drive fail.
    I want to use AHCI, but have also tried IDE, both SATA control methods fail.
    Error messages are erratic. They happen at different times during the installation. The messages themselves are always different. Sometimes a blue screen, sometimes one or more error popups from the install utility, sometimes it just freezes.
    Mainboard: MSI P35 Platinum
    Processor: Intel Core2 Duo E6750 2.66GHz|1333MHz|4MB
    RAM: Patriot Extreme 6GB|DDR2|800MHz|2x2GB|2x1GB
    Video: MSI NX8800GT 512MB
    Optical: Asus DRW-2014L1T SATA
    HDD: Seagate 500GB|SATA
    Power Supply: OCZ GameXStream OCZ700GXSSLI +3.3@36A|+5V@30A|+12V1@18A|+12V2@18A|+12V3@18A|+12V4@18A|[email protected]|[email protected]
    I drive a Buick.
    Any ideas appreciated.

    Ugh , I forgot to increase the voltage to RAM after updating to BIOS 1.C. Apparently even at relaxed/spec clock speed and timings, it will not run at 1.8v. I increased the voltage to 2.2 and everything was back to normal. I should have deducted from the erratic errors that the RAM was the fault. Such an angry, yet relieved feeling once it finally hit me. 
    Thanks for the help.

  • KA92 Platinum Bios Update

    Hello.  I have built a gaming system for a customer, and after a few weeks of use, it now will not consistantly pass the post test.  I say consistantly, because 1 out of 7 or 10 times it will boot and then work fine, however most of the time it will fail the post with 1 long and 8 short peeps, which I have already researched.  All parts were new, and nothing has been changed on this system.  Yet the problem happened.  I have cleared the CMOS, and removed the memory and have cleared all power through the system and still the problem persists.  I believe that the bios version is 1.0 and the newest is 1.4.  I was hoping that someone could provide me with clear instructions for doing the bios update to version 1.4 using a USB flash drive.  The live update tool will not work as the system is running Vista 64bit SP1.  All and of course the system does not have a floppy drive. System specs are listed below, and again please list the instructions in detail.  Thank you for your help in advance, Todd.
    System Specifications:
    MSI K9A2 Platinum AM2+/AM2 AMD 790FX ATX AMD Motherboard
    AMD Athlon 64 X2 6400+ Windsor 3.2GHz Socket AM2 125W Dual-Core Processor Model ADX6400CZBOX
    2 sets (4GB - 4 dimms) Crucial Ballistix 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory Model BL2KIT12864AA1065 Seagate Barracuda 7200.10 ST3250410AS 250GB 7200 RPM SATA 3.0Gb/s Hard Drive
    LITE-ON 20X DVD±R DVD Burner with LightScribe Black SATA Model LH-20A1L-05
    LITE-ON 20X DVD±R DVD Burner Black IDE Model DH-20A4P-04
    2 - MSI RX2600XT Diamond Plus Radeon HD 2600XT 512MB 128-bit GDDR4 PCI Express x16 HDCP Ready CrossFire Supported Video Cards

    Quote from: BOSSKILLER on 17-April-08, 05:13:57
    Don't use generic noname PSU, also avoid "Apevia".
    Use quality PSU with powerfull large single rail good brand, like PC & Power Cooling, Corsair, Enermax e.g.
    Good PSU suggestion with other info here:
    https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246
    Add-on to read:
    PSU's---2 x 12v---The Dual Rail Myth
    Is your problem caused by your PSU?
    Unfortunatly I don't think that I can return it at this time.  It has been more then 30 days.  It bought it becasue it had a $50 rebate, but was still a $140 PSU before rebate.  I didn't think that I was getting a cheap one, but I guess I was wrong.  I usually only ever buy Thermaltake and occasionally Cooler Master.  I have had good luck with both in the past.  Thermaltake is worth the money in my opinion.  If the Apevia goes bad again, then I will try to exchange for credit, but since I threw the orginal box away, newegg wouldn't work with me at this time.  :(

  • Msi P35 platinum: bios auto-raises NB & SB voltages when fsb over 316

    Why does this happen when I'm overclocking FSB in bios and reaching over 316, NB voltage goes 1.250V->1.450V and SB I/O Power 1.5V->1.8V automatically. Both are in red text after this.
    Of course, I can try to lower these settings back to normal but never tried.. I've just left these raised voltage settings because everything is running fine (now E2140@2816MHz,352FSB). But are these settings safe (NB 1,45V and SB I/O 1,8V) ??
    I know that raising NB voltage is necessary when raising up FSB but SB I/O Power voltage?
    Should I try lower these voltages and see if my computer is still stable?
    I have bios v1.6, mobo msi p35 platinum rev1.1...
    Please help me

    this is probably due to overclock jumper's setting for FSB STRAP(200/266/333).
    With my Neo 2 Fr (pretty similar) about the same happen to me but at 382...then I moved the jumper to the 333 setting (see manual) and no more change in voltage of NB and SB over 382.
    If you do so, be careful on your setting before the change of position of the jumper as it automaticaly add 67 mhz to the FSB and so the system may not start because of too high cpu freq. Be careful also on memory multiplier (before the change set it to 1:1 or calculate the ram freq. (FSB+67 mhz and your memory multiplier)) as the system may not start because of the RAM.
    However even if it not start after 2-3 reboot it start in safe mode(as after OC) and you can change the settings.
    My advice:I think your cpu fsb by default is 200, if so and if you don't plan to go over 382 set the jumper to 266 (you should be ok with voltages until 382mhz of FSB.
    Always remember what said over about the +67 mhz on FSB when you move the jumper!!!!

  • P35 platinum bios memory timings

    hi
    i have a question about the memory timings in the BIOS in the P35 Platinum
    once you changed the value to manual
    all the settings become available to change
    i'm only interested in the first four setting i.e. cas trc trp tras
    i dont know and dont care about the other settings
    but their is no way to turn them on auto
    should i assume that the initial settings they have are taken from the SPD and are therefore safe

    Quote from: hapi.djus on 22-September-07, 03:32:09
    Is the TRC the same as the TRFC?
    not is not the same i'm also looking for the trc option but i couldn't fin it nether
    -Row Cycle Time (tRC).
    Determines the minimum number of clock cycles a memory row takes to
    complete a full cycle, from row activation up to the precharging of
    the active row. For optimal performance, use the lowest value you can,
    according to the tRC = tRAS + tRP formula. For example:
    if your memory module's tRAS is 7 clock cycles and its tRP is 4 clock cycles,
    then the row cycle time or tRC should be 11 clock cycles.
    -Refresh to Activate Delay / Refresh Cycle Time (tRFC).
    Determines the number of clock measured from a Refresh command (REF)
    until the first Activate command (ACT) to the same rank
    if you want all the definitions view this page http://www.tweakers.fr/timings.html
    my memories work at 5-5-5-10-38-6-3-3-3 @866MHz waiting for my others ballistix to lower more the timings

  • P35 Platinum bios upgrade

    Hi there
    Did anyone here get an error message saying "Invalid checksum" when upgrading to MSI's latest bios(1.6) for the P35 Platinum. I done the flash thru liveupdate and restarted my PC and it showed me that message then just rebooted again and into windows. Also ive never ran DualCore centre before, i installed it after i flashed the bios and it just gives me error message and doesnt run.
    Man i should have stuck with GigaByte

    Quote from: TeamSR20 on 26-November-07, 07:25:05
    Did anyone here get an error message saying "Invalid checksum" when upgrading to MSI's latest bios(1.6) for the P35 Platinum. I done the flash thru liveupdate and restarted my PC and it showed me that message then just rebooted again and into windows. Also ive never ran DualCore centre before, i installed it after i flashed the bios and it just gives me error message and doesnt run.
    Got exactly the same message after upgrading to 1.6 from 1.4 that came with the board.
    Unfortunately I'm not even able to boot up to Windows now !   
    I've switched it off and given up for the night, will try again tomorrow.....   

  • K2N2 Delta 2 Platinum Bios update Problem

    Hello All,
    I just got myself in trouble again
    My setup is a two sata disc raid system, which was working perfectly but with a black screen reboot every now and then, so I though a bios update may solve the problem.  
    So I update the bios using live update3 but I think it's gone wrong.
    After updating the raid option didnot show at all and I got a ( A disc read error occurred) so I tried clearing cmos and re boot.
    When I rebooted the (cmos checksum error - defaults loaded    - Press F1 to continue,  DEL to enter SETUP), on pressing F1 the (A disc read error occurred)
    came up, so I used the rescue disc to reinstall previous bios but same result.
    In bios setup I set 1st boot to hard disc, but with the platinum there is also a Priorty boot selection which you press enter to see the settings, which are -
    1. Ch2  M.      Maxtor 6Y120M0
    2. Ch3  M.      Maxtor 6Y120M0
    3. Bootable  Add-in Cards
    I set the 1st boot device to Hard Disc as it does not show scsi, it does show Lan, USB devices and the normal cd rom and floppy.
    The big problem is I can't see the raid arrey on post so I can get in to see if it's working OK.
    I would be most grateful for any help
                                Very Best Regards
                                                           Peter T

    Hello Labtech 1,
    May the sun allways shine on you and great happyness be your s forever .
    What I mean is you where spot on, a big thank you.
    How could I be such a twonk? I should have taken a bit of time with the manuel.
    Everything is working fine again (for the moment).
                                                   Best Regards
                                                                      Peter T

  • PH61A-P35 (B3) bios update..........file not found

    Hello, ihave problem. I tried to update BIOS, so download bios file, unzip to flash drive, execute bios file on flash drive, and after only wait and system restart. But when he started i can read only red inscription "BIOS  Updating ________________ File not found."
    Is here any chance to recovery old bios or even bios update?
    Please help me, i am very disappointed :(
    thanks very much.

    Recommend to give the forum's USB method a try;
    >> Forum USB Method <<

  • Msi neo2 p35 + E8500 bios update

    Hey
    i cant update the bios i downloaded the latest version 7345v1a and im told to burn an iso file and then boot up but no files match the iso program when i try to compile. im sorry for typos but im dansih 
    /Fudge

    Fudgeman, please be more specific about your issue.  What is your current BIOS Version?  Why do you need a BIOS Update?  If you have an E0-Stepping processor, a too old BIOS Version and want to update your BIOS because the system seems to freeze up during POST (and does not accept keyboard commands), you cannot simply update your BIOS in a standard procedure.  You either need to put in a supported CPU first or try if the AMI Recovery Routine can be forced to run (for this procedure you need an internal floppy drive and a PS/2 Keyboard).

  • MOVED: K8N SLI Platinum - BIOS Update

    This topic has been moved to AMD64 nVidia Based board.
    K8N SLI Platinum - BIOS Update

    Sorry, I'm dozzy...     I've since discovered that it's a 219 Mhz problem, there's a sticky in the overclocking section on how to overcome it, and it doesn't apply to me anyway, 'cause I've got a Venice...

  • P6N SLI Platinum Bios Update

    I have XP 64-bit edition
    and I want to be able to update my bios i just got the board and the bios update is need...how do i update it? When i install Live Update tells me service wasn't started and flash_mimo device control error ...not really sure where to get the bios flash utility to do it from a floppy disk...

    Quote from: harmanoff on 19-July-07, 23:52:06
    Alright I will try those things...do i have to put the newest bios on the USB key or is that done for me to?
    no just execute tool from windows 1st and point to the bios file or bios .zip archive when asked, choice your USB letter and wait a tool to finish. then reboot and boot from it. no need to copy anythink to the usb key.
    look for steps here:
    https://forum-en.msi.com/index.php?topic=109082.msg809672#msg809672

  • P6N SLI Platinum Bios update in Vista x64

    Just wondering how I update the bios for my P6N SLI Platinum in Vista x64?  When I d/l the bios all the stuff is for 2000/me/xp.  Why is there no vista support under anything?

    Use the USB flashing tool developed here at the forums.
    clickme>>MSI Forum HQ USB flashing tool!!!<<clickme

Maybe you are looking for