P45D3 Platinum - System staggers with drive access

Hello all,
here is my config:
P45D3 platinum board
Intel 3.0G dual core
4GB 1333 DDR3 memory
Asus video with ATI 4870x2 chipset
3 HDD in RAID 5
1 DVD-RW on Sata
1 DVD-RW on IDE
Vista 64 Ultimate
The system is recently built and using the included raid driver. I also have the MSI utilities installed.
Upon load of OS, after logon, and anytime I do a drive refresh (such as starting My Computer), I see the system stagger in about 1 second increments for 7-10 times. The system runs great otherwise. The staggering stops the entire system for those brief instances. If it weren't for the slow booting due to the staggers I might just ignore it. Please chime in on your ideas as I'm out of them.
Volvernon

What is the model of your RAM? Can you also list the PSU specs amps as well?

Similar Messages

P45d3 platinum with geil PC3-12800 1600MHz 7-7-7 DC Kit

Hi to all in September it will arrive to me p45d3 platinum with the geils PC3-12800 1600MHz 7-7-7 DC Kit however reading in the forum there are also problems with memories 1333 mhz and it needs to plan her to 1066 mhz.
Will this problem be resolved?
Is the technical support aware of the problems?
Thanks

Quote
I just have 2 other OCZ RAM [OCZ3P13332GK] and freezes become -hardcore- with it. -> it's worst
Well, those modules are known trouble makers. "DDR3-1333" is an overclocked rating to begin with (they are actually just DDR3-1066 sticks) and they require 1.8V (0.3V above DDR3 industry standard). Search for "OCZ3P13332GK" in the OCZ Forum. You will find 133 threads, most of them about stability problems on all kinds of different systems.
Quote
It's the timings I usually use
I did not say anything about timings, but about frequency and voltage settings.
Quote
beside it's DDR3-16000 with XMP profile, factory tested
XMP Profiles are overclocking profiles. Where those modules "factory tested" on your particular mainboard? Where does OCZ mention what systems/chipsets where used during the test procedures to see if the memory overclock results in a stable system in all possible system configurations? That is why I stay away from OCZ. Too many compatibility problems because of non-standard operating parameters.
According to Intel Specifications, the Intel P45 Chipset is only specified for DDR3-800 and DDR3-1066 operation. That is it.
Quote
I'm a bit disappointed (2 years having problems).
Well, the question is where the problems originate. If the problem related to the brand of memory modules or the board needs to be found out by testing. I told you that two years ago:
https://forum-en.msi.com/index.php?PHPSESSID=1aa3592c1969cc6b801df9255eb8aba2&topic=119076.msg898953#msg898953
Quote
Zoidberg_fr, can you test a different set of DDR3-RAM (preferably not factory-overclocked and non-OCZ)?
... and the suggestion is still the same now.
If there is a problem with the board (and it could have been a problem with the board two years ago), RMA would have been the right thing to do. Now it is almost a little late for that.

Problem with MSI P45D3 Platinum

Hi, I've just built myself a new computer but it wont start. When I turn the power on on the power supply all that happens is a red led on the motherboard starts to flash. The led is under my graphic card on the right hand side of the board, I think its the led3 thats flashing. Nothing else works, the power supply fan and the cpu fan both dont run. The power switch on the front of the case does not work.
Is the red flashing led the standby led?
Any help would be great.
MSI P45D3 Platinum
Intel core 2 quad q8400 2.66ghz 4mb lga 775 fbs1333
XFX geforce gtx 260 576mhz 896mb pci-express 2.0 dvi
OCZ Technology ddr3 4gb (2x2) fatal1ty 1333mh
Western Digital Caviar se16 320gb s300 16mb
Best Value he 800w black 80+ high efficiency psu quad 12v 800t

Try to push the onboard-power-on button and see if that changes anything.
In case the problem still occurs, please take the board out of the case and test it on a non-conducting surface in barebone configuration.
If that still does not solve the problem, test a different Power Supply Unit, maybe your's broke (had the same symptoms once with a broken Be Quiet PSU on a P45 Platinum).
Should a different PSU not solve the problem, RMA the board.

Is snow leopard usb backup drive access much much quicker using firewire than with usb 2.0 ?

is snow leopard usb backup drive access much much quicker using firewire than with usb 2.0 ?

I migrated from a USB2 external hard drive (when it failed) to the Firewire 800 and have not looked back. I also sync from that primary drive to a secondary backup drive (still USB2). Everything I do with the firewire drive is significantly faster than USB2.

P45D3 Platinum (MS 7513-010R) Windows Installation UEFI Click Bios 1.43

Hallo!
I have tried RAID0 system with Windows Vista64 with integrated Sp1 and Windows 7 64 RC from the UEFI shell to install. In the screen with the Intel RAID BIOS Setup is entered with Ctrl. I is not possible. Existing RAID0 keyboard input is possible only from the window for entering into the Click BIOS Keyboard with Del possible.
After running bootx64.efi pass about 30 seconds until the lettering Press any key to boot from CD or DVD appears. Keyboard input disappear after a further 3 minutes until the window with the progress bar Windows is loading files appears. The Progress bar takes 1 hour 25 minutes to the end of DVD drive is constantly in operation LED blinks. Partitioning the hard drive with GPT in the setup program is possible. After rebooting the system after the expansion of the files if the installation does not continue, but in Bios mode reboot.
An installation in a non raid system in AHCI mode is the starting time of 90 minutes to equal partitioning, however, interrupt the installation of Windows when copying files from a Blue Screen.
In IDE mode lasts until the installer to copy the Windows files, about 40 seconds. Cancels but to restart the setup program with a blue screen from.
I have Experimental the memory clock of my memory from 1333 MHz to 1066 MHz also no success
In the BIOS emulation mode does the installation of Windows in about 25 minutes. The System is instabile Blue Screens "Memory_Manager" I did several tests with my Ram with memory diagnostic programs, the results of the tests errors in memory.
Under the legacy Bios 1.74 proceeded to install Windows Vista and Windows 7 correctly and in the normal time frame. The loading of the Windows Setup files "Windows is loading files into memory did not last longer than a minute the rest of the installation 20 minutes. Both in the IDE, AHCI and RAID0 mode. Access to the RAID Bios with the keyboard works flawlessly. Diagnostic tests of memory real flawlessly. The system is running properly and stable.
My System: Memory is a DDR3 Corsair 2x2 GB 1333Mhz (Memory Info is: Corsair CM3X2048-1333C9DHX
XMS3-1333 2048MB 1333Mhz 9-9-9-24 1.50V ver3.3 09202499 2 Modules 4GB DDR3 Dual Chanell) CPU Intel E6850 3Ghz. FSB 9x333 Mouse and Keyboard USB 2.0 Devices. DVDRAM and HDD SATA devices
Best regards
Chris72

Hello!
The problem I had with UEFI Click Bios 1.43 my system can not use.
A UEFI installation of Windows from the UEFI shell is not possible neither in IDE, AHCI or RAID mode, loading the Windows setup files in the RAM more than 90 minutes after discontinuation of the installation disk partitioning with bluescreen. An installation in bios emulation mode while the system is very unstable faults in RAM, often with a system crash.
At 19.06 I was at the Customer Service Support by MSI changed
In response, I received at 20.06 that a test is made.
At 02.07 I update miy BIOS with the latest legacy Bios 1.74 to check if the problem still persists
(Under Bios 1.74 proceeded to install Windows Vista and Windows 7 correctly and in the normal time frame. The loading of the Windows Setup files "Windows is loading files into memory did not last longer than a minute the rest of the installation 20 minutes. Both in the IDE, AHCI and RAID0 mode. Access to the RAID Bios with the keyboard works flawlessly. Diagnostic tests of memory real flawlessly. The system is running properly and stable.) The Problem is UEFI Click Bios 1.43
At 14.07 I received a final response from MSI:Quote
1.For the EFI bios is only for ERP 020 for thr hardware design and at the same time,the original bios of 010(your motherboard version) is legacy bios.
2.If U insist to use EFI bios and please feed back the issue to your reseller direcly because that we could find the same memory as your's indeed.And the reseller will help you or ask MSI HQ for help.Sorry for any inconvenience caused.
This answer I do not quite
An answer to my question whether the error was reproducibly remained unanswered
1. Is there a P45D3 Platinum with ERP 020 (ms 7513-020) available?
2. How can I Windows Vista 64 with SP1 or Windows 7 RC from the UEFI-shell to correctly install?
3. Is My Memory compatible with UEFI Click Bios V.1.43?
Best regards,
Chris72

P45D3 Platinum Unable to Overclock

The initial BIOS version（1.0） Overclocked just fine.But when I upgraded to the latest version of the BIOS(1.8/1.9) Problems began to appear. CPU FSB Frequency or CPU Ratio could not be modified even with +1Mhz , If do so save and exit bios restart system for the first time during Windows7 starting process after microsoft logo appear then suddenly blue screen then restart the system and bad things happened.CPU Fan running at full speed nothing shows on monitor‎,That's right The same situation with overclocking failure But this time reboot the system three times save system form failed overclocking mechanism won't work the only option is to Clear CMOS.After Cleared CMOS enter the BIOS Cell menu this time CPU Ratio shows 60.
My Hardware Specifications:
Mainboard:MSI P45D3 Platinum BIOS 1.9
CPU:Intel® Core™2 Extreme Processor QX9650 (12M Cache, 3.00 GHz, 1333 MHz FSB)
Memory:Corsair 4G DDR3 1600 CMX4GX3M2A1600C9 2G*2
It's seem the situation I described above is happened to those CPU Ratio adjustable Intel Extreme Edition Processor.
Wait reply....
regards..

- Fixed system report incorrect memory size when install 4G memory.
- Support 1000 GB HDD.
- Support NV 9X series VGA card.
Because these fix and support are suitable for my situation.I am currently installing 12G memory and 2TB WD Hard Drive also NV 9X series VGA card are exactly in use.
I have tried many other versions such as 1.7 1.6 1.5 1.4 1.3 1.2 1.1 but the situation is the same。

MOVED: P45D3 Platinum Motherboard Ram Settings and detection

This topic has been moved to Intel Core 2 Duo/Quad boards.
https://forum-en.msi.com/index.php?topic=119831.0

All right, sorry my first post.
# CPU brand, model and speed (eg AMD Athlon64 3000+ 'Venice' core)
QuadCore Intel Core 2 Quad Q6600, 2400 MHz (9 x 267)
# Motherboard model (eg K7N2 Delta2 Platinum, NOT just MS-6570!!)
P45D3 Platinum by MSI
# Memory brand, type/speed, size, number of sticks (eg 2x Crucial 512mb DDR400)
MDT Tech. MDT 1GB DDR3-1333 x2 in Dual Channel Mode
# Video card brand, chipset type, memory size (eg Gainward Geforce 6800GS 512mb AGP)
MSI Geforce 8800 GTX with 768 MB Ram
# Hard drive(s) brand, size, type, speed (eg 2x Seagate 200gb SATA150)
WDC WD1500AHFD-00RAR1 (150 GB, 10000 RPM, SATA)
WDC WD50 00AAKS-65YGA0 USB Device (465 GB, USB)
SAMSUNG HD501LJ (500 GB, 7200 RPM, SATA-II)
# Any other peripheral cards and devices (eg MSI TV@nywhere Plus TV card, MSI DigiVOX USB2 TV tuner)
Creative SB X-Fi XtremeMusic/Platinum Sound Card
Linksys Wireless-G PCI Network Adapter with SpeedBooster
# Operating system and version (eg Microsoft Windows XP Home Edition SP2)
Microsoft Windows XP PRO SP3
# Power Supply Unit brand and output in watts and DC output (amps)
Coolermaster Real Power 850 WATT
All i want to know how to run my ram at 1333 Mhz. Bios wont let me chose anything above 1066 Mhz.

P45D3 Platinum Motherboard Ram Settings and detection

Well i have this motherboard and 1333 MhZ DDR-3 RAM (2*1GB dual channel kit by MDT).
The OC jumpers are at default which means 200 MHz FSB.
I have all on AUTO detection in the bios wherever possible.
The manual says Memory Support:
4 DDR3 DIMMS 1333/1066/800 MHz and up.
The problem i got is that my memory is only detected as 1066 MHZ and there is no way to get a higher setting with the standard settings you can choose, 1:2 being the highest.
What do i have to do to run my memory at 1333 MHz?
Bios is version 1,4

All right, sorry my first post.
# CPU brand, model and speed (eg AMD Athlon64 3000+ 'Venice' core)
QuadCore Intel Core 2 Quad Q6600, 2400 MHz (9 x 267)
# Motherboard model (eg K7N2 Delta2 Platinum, NOT just MS-6570!!)
P45D3 Platinum by MSI
# Memory brand, type/speed, size, number of sticks (eg 2x Crucial 512mb DDR400)
MDT Tech. MDT 1GB DDR3-1333 x2 in Dual Channel Mode
# Video card brand, chipset type, memory size (eg Gainward Geforce 6800GS 512mb AGP)
MSI Geforce 8800 GTX with 768 MB Ram
# Hard drive(s) brand, size, type, speed (eg 2x Seagate 200gb SATA150)
WDC WD1500AHFD-00RAR1 (150 GB, 10000 RPM, SATA)
WDC WD50 00AAKS-65YGA0 USB Device (465 GB, USB)
SAMSUNG HD501LJ (500 GB, 7200 RPM, SATA-II)
# Any other peripheral cards and devices (eg MSI TV@nywhere Plus TV card, MSI DigiVOX USB2 TV tuner)
Creative SB X-Fi XtremeMusic/Platinum Sound Card
Linksys Wireless-G PCI Network Adapter with SpeedBooster
# Operating system and version (eg Microsoft Windows XP Home Edition SP2)
Microsoft Windows XP PRO SP3
# Power Supply Unit brand and output in watts and DC output (amps)
Coolermaster Real Power 850 WATT
All i want to know how to run my ram at 1333 Mhz. Bios wont let me chose anything above 1066 Mhz.

I am stuck... !P45D3 Platinum

Hi!
My computer:
P45D3 Platinum
Intel Q9400 Quad 2,66
Samsung HD501LJ x 2
Samsung HD040GJ
Optiarc DVD RW
Crucial Ballistix 1 Gb (got one more not yet installed)
Sapphire Radeon 2650 Pro
Corsair CMPSU-750TXEU 750W
I have tried to solve this problem a couple of weeks without no success.
Bios doesn´t find any of my sata 500 GB disks, it´s only find the very old 40 gig (also SATA).. and my Ide dvd player.
I have tried to install Windows Xp, I comes as far to "Windows Xp begins" (in the installation process..) when a blue screen apears.
So I tested to install Ubuntu, with no problem.. (apart from that I am a beginner at linux, and got all the usuall problems....)
I wanted to try update my bios, but how ??..
the MSI Forum HQ USB Flashing Tool requires a windows installation on a computer with msi board..
I was plaining to use my old computer to unpack it in to an usb flash drive...
Please help!

Quote
Beginning to think that also my harddrives died..
Well, you should check that first. It does not make much sense to keep trying things if you are unsure if the drives are even operable.
Quote
how can I get Windows to further work on my old 40 gig..?
Quote
when a blue screen apears.
What is the error message that appears on the blue screen? Please write down the STOP ERROR Code and check if a specific file is mentioned.

Creative Audigy Platinum Installation Help with Pentium 4 3.2GHz HT Enab

:mansad:
Dear Fellows,I have recently upgraded to a new Pentium 4 machine. The config is as follows:Pentium 4 3.2eGHz MB cache HT (Hyper-Threading Enabled)Intel Original 865GBF MainboardGB Kingston DDR 400MHz RAM20GB SATA WD HDDSound Blaster Audigy PlatinumATI RADEON 8500 DV 64MBThe problem I am facing is with Audigy Platinum. Once I install the operating system (Win XP) and move to the installation of Creative Audigy Platinum Sound card. All the applications are installed and the system hangs while updating *drivers*. I restarted but it corrupts the whole operating system conflicting with Display Driver, Mainboard driver as well as Windows. CD/DVD Rom also disappear. I then reinstalled operating system again. I would like to request for help and solving this issue and I dont want to get rid of Creative Audigy. I have heard complaints with Hyper-threading technology but I disabled it and the same problem occured. I tried everything e.g. latest drivers from Creative website, BIOS updates, Driver updates etc etc. The problem starts once the drivers are to be updated for Creative Audigy Platinum.Anticipating your response soon.Regards,

Hi Jeremy,
I would like to thank you for your kind assistance with my problem.
Heres the good news, I finally managed to install and run my Creative Audigy Platinum perfectly.
Credit goes to your assitance and support.
For your info, I would like you to know what I really did.
I have an Intel Genuine 865GBF mainboard. I installed clean copy of Windows XP (SP) and downloaded and installed latest Chipset INF utility from Intel website. I guess this utility tells the mainboard what kind of hardware is configured on the board.
Please note that I did not add any PCI card except the AGP graphics card.
After finishing Windows XP, I installed the Creative Audigy Card in a different PCI slot. When windows started, it detected the sound card installed.
I simply ran the driver and programs from the Creative CD and it installed perfectly. I then updated the drivers downloaded from the Sound Blaster site in correct order.
After finishing with Creative Audigy Platinum installation. I installed other hardware devices, service packs, AV and applications.
Its the third day and everything is running well.
I just wrote the steps if someone else faces the same problem, he/she can sort it out the same way.
Thanks again for your help.
Best regards,

PC won't boot after memory upgrade (on MSI P45D3 Platinum)

I am having a problem on my MSI P45D3 Platinum motherboard system (Dual OS: Win XP and Win 7)
Until recently I was running it on PATRIOT 2GB (2x1GB) 1600MHz DDR3 PDC32G1600LLK memory (CL7) and all was fine, though running only at 1066MHz, since I couldn't tweak the settings (latencies/voltage) in order for it to run at 1600MHz.
I wanted to add RAM but since I couldn't find the same type anywhere in my town, I decided to go for PATRIOT 4GB (2x2GB) 1600MHz DDR3 PSD34G1600KH Signature Line (CL9). However, the system never booted again (blank screen, no signal sent to monitor) after adding the two new sticks of RAM! The new RAM is working fine when I remove the old and vice versa, so I know it is not a case of defective sticks.
I must mention that I cannot fiddle with the RAM timings because I cannot even reach BIOS!
Any help will be most welcome!

Mixing different memory modules is always a gamble and likely to cause such problems. Identical modules should be used for best results.
In many cases, you can set what you want regarding memory configuration, getting the RAM mixture to work stable will simply be impossible, even though there is no defect.

Need help with thinkvantage access connection

Here a log file with new access connection:
Connection status:  Disconnected
Cause:  Driver disconnected while associating.
Error code:  229378
Recommended actions:
Verify that the encryption settings (WEP/TKIP/AES) specified in this profile match those expected by the wireless network.
Verify that the wireless adapter in your computer has not been restricted from accessing the radio channels being used by the wireless network.
If the problem persists, contact your network administrator and provide the troubleshooting information below.
Adapter Details
Adapter name  11a/b/g Wireless LAN Mini PCI Express Adapter
Adapter type  Wireless LAN
Adapter speed  54.0 Mbps
Driver/Firmware version  7.6.0.96/ N/A
Adapter status  Enabled
Connection Status  Disconnected
Disable unused cards?  Yes
TCP/IP Settings
DHCP enabled?  Yes
Append parent suffixes of the primary DNS suffix?  Yes
Register connection's DNS suffix in registration?  Yes
Register connection's DNS suffix in DNS registration?  Yes
Enable LMHOSTS Lookup?  No
NetBIOS setting  "Default"
Wireless Settings
Network name (SSID)  linksys
Connection type  Access point
Wireless mode  Auto
Security encryption  None
System Information
System model  7732CTO
BIOS version  7LETB7WW (2.17 )
Operating system version  Windows Vista, Service pack 2
Access connections version  5.31
Access Point scan list
Network name (SSID)              Wireless mode MAC address                   Signal strength Channel
linksys                          802.11g        00:1C:10:54:65:B6              24%            11
Global Settings
Network
Allow all users of this system to switch to any existing location profile  -> No
Allow the wireless LAN radio to be turned off when inactive  -> No
Allow selection of location profiles with Fn+F5 On Screen Display menu  -> Yes
Enable autodeletion of unused profiles  -> Yes
Notifications
Show ThinkVantage Access Connections status icon in task tray  -> No
Show wireless status icon in task tray  -> No
Display the progress indicator window when a profile is being applied  -> Yes
Preferences
Enable sound effects  -> Yes
Do not show balloon tips from the Access Connections system tray icon  -> Yes
Show WiMAX page as default on Main GUI  -> No
Automatic location profile switching list
Include Ethernet connections in automatic switching and prompt me to save Ethernet ports  -> Yes
When no other connections are available, connect through Wireless WAN or WiMAX  -> No
Wireless priority list
Selection    Priority     Location profile name                                            Connection order                 Connection details
No                  1     linksys                                                          Wireless LAN                     SSID: linksys
Log File
Debug Log is enabled
It didn't happen when I use old version. Can anybody help me?

Are you getting any error message while connecting to ds..?
Are you able to go online on wired computer...?
Are you able to go online on any wireless computer on your network..?
Open the router setup page and under the wireless tab,Change the Channel width to 20MHz only and Channel to 11-2.462GHz and click on save settings...Under the Advanced Wireless Settings...Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...
Now,check.

SSIS BULK INSERT unsing UNC inside of ForEach Loop Container Failed could not be opened. Operating system error code 5(Access is denied.)

Hi,
I am trying to figure out how to fix my problem
Error: Could not be opened. Operating system error code 5(Access is denied.)
Process Description:
Target Database Server Reside on different Server in the Network
SSIS Package runs from a Remote Server
SSIS Package use a ForEachLoop Container to loop into a directory to do Bulk Insert
SSIS Package use variables to specified the share location of the files using UNC like this
\\server\files
Database Service accounts under the Database is runing it has full permission on the share drive were the files reside.
In the Execution Results tab shows the prepare SQL statement for the BULK insert and I can run the same exact the bulk insert in SSMS without errors, from the Database Server and from the server were SSIS package is executed.
I am on a dead end and I don’t want to re-write SSIS to use Data Flow Task because is not flexible to update when metadata of the table changed.
Below post it has almost the same situation:
https://social.msdn.microsoft.com/Forums/sqlserver/en-US/8de13e74-709a-43a5-8be2-034b764ca44f/problem-with-bulk-insert-task-in-foreach-loop?forum=sqlintegrationservices

Insteresting how I fixed the issue, Adding the Application Name into the SQL OLAP Connection String Fixed the issue. I am not sure why SQL Server wasn't able to open the file remotely without this.

Time Machine fails with drive connected to Airport Extreme

First of all, I've had myriad problems with Time Machine, even when it was connected directly to my MBP. But after the recent updates, I installed them and hoped it would work wirelessly. I re-formatted my 120GB OWC drive (my MBP has 30GB available of 120GB). I have already been down the road of making sure I've formatted the drive correctly.
I excluded my system folder, my entourage identity, downloads, and my Parallels Windows XP file from the backup. I connected the drive to my Airport Extreme (not the gigabit version) and started the backup. Basically, it gets about 5 GB into the backup, moving very slowly, and then fails, saying that it couldn't locate the drive. And that part is true--I can't seem to locate the drive on my network anymore either. And eventually, after another hour or so, my Airport Extreme drops as well, and isn't even available. Even when I unplug the AE, and plug it back in, it still doesn't show up...but after about an hour or so...it pops back up and is available, working fine. My iPhone sees the same problem with AE dropping and then coming back. When the wireless service drops, I can plug an ethernet cable into the AE and I can access the internet fine, so it's not the cable modem (Time Warner).
Is anyone else seeing this problem? I'm no guru and appreciate that Macs just seem to work correctly. But Time Machine is making me pull my hair out. It's been an unmitigated disaster from start to finish.
Appreciate any help!

This is probably the most sensible post I've read on the issue. I've spent the last 2 days trying to get my 500GB LaCie Quadra hard drive to work with my Airport Extreme (the square one, yes .
I've formatted it correctly with the Disk Utility (multiple times!).
Airport Utility sees it just fine. I can back up to it when it is connected directly to my MacBook via USB.
But when the drive is connected via USB to the Airport Extreme, Time Machine doesn't see it -- unless I turn on file sharing with guest access read and write. That seems less-than-secure to me even if my network is protected.
Without guest access the drive appears in the shared section of the Finder, but I can't connect to it. I've tried all three combinations under "Secure Shared Disks" but none of them work.
Seems like its just too flaky to use an external disk connected to the Airport Extreme.
Happy to be pointed in the right direction... are there specific file permissions I should be setting my external drive to?
Thanks,
Rich

Problem with file access in other computer in jsp

I have problem with file accessing in other computer in jsp.
The follow code
File folder=new File("Z:"+File.separator+"sharefolder");//Z is a net share driver
File[] files=folder.listFiles();
System.out.println("test");
System.out.println("length="+files.length);
will throw exception at the second print.
but it works well in main funtion.
Is anybody know what is the problem.
JSP works on windows2003 server,tomcat 5.0.28 JDK1.4 net share folder on windows2000 server

no error code for this.But when I start tomcat I get the follow error.
java.lang.IllegalArgumentException: Document base Z:\ does not exist or is not a readable directory
     at org.apache.naming.resources.FileDirContext.setDocBase(FileDirContext.java:138)
     at org.apache.catalina.core.StandardContext.resourcesStart(StandardContext.java:3910)
     at org.apache.catalina.core.StandardContext.start(StandardContext.java:4138)
     at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:823)
     at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:807)
     at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:595)
     at org.apache.catalina.core.StandardHostDeployer.addChild(StandardHostDeployer.java:903)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at org.apache.commons.beanutils.MethodUtils.invokeMethod(MethodUtils.java:216)
     at org.apache.commons.digester.SetNextRule.end(SetNextRule.java:256)
     at org.apache.commons.digester.Rule.end(Rule.java:276)
     at org.apache.commons.digester.Digester.endElement(Digester.java:1058)
     at org.apache.catalina.util.CatalinaDigester.endElement(CatalinaDigester.java:76)
     at org.apache.xerces.parsers.AbstractSAXParser.endElement(Unknown Source)
     at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl.scanEndElement(Unknown Source)
     at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl$FragmentContentDispatcher.dispatch(Unknown Source)
     at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl.scanDocument(Unknown Source)
     at org.apache.xerces.parsers.XML11Configuration.parse(Unknown Source)
     at org.apache.xerces.parsers.XML11Configuration.parse(Unknown Source)
     at org.apache.xerces.parsers.XMLParser.parse(Unknown Source)
     at org.apache.xerces.parsers.AbstractSAXParser.parse(Unknown Source)
     at org.apache.commons.digester.Digester.parse(Digester.java:1567)
     at org.apache.catalina.core.StandardHostDeployer.install(StandardHostDeployer.java:488)
     at org.apache.catalina.core.StandardHost.install(StandardHost.java:863)
     at org.apache.catalina.startup.HostConfig.deployDescriptors(HostConfig.java:483)
     at org.apache.catalina.startup.HostConfig.deployApps(HostConfig.java:427)
     at org.apache.catalina.startup.HostConfig.start(HostConfig.java:983)
     at org.apache.catalina.startup.HostConfig.lifecycleEvent(HostConfig.java:349)
     at org.apache.catalina.util.LifecycleSupport.fireLifecycleEvent(LifecycleSupport.java:119)
     at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1091)
     at org.apache.catalina.core.StandardHost.start(StandardHost.java:789)
     at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1083)
     at org.apache.catalina.core.StandardEngine.start(StandardEngine.java:478)
     at org.apache.catalina.core.StandardService.start(StandardService.java:480)
     at org.apache.catalina.core.StandardServer.start(StandardServer.java:2313)
     at org.apache.catalina.startup.Catalina.start(Catalina.java:556)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:287)
     at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:425)
Jun 5, 2006 6:55:41 PM org.apache.catalina.core.StandardContext start
SEVERE: Error in resourceStart()
Jun 5, 2006 6:55:41 PM org.apache.catalina.core.StandardContext start
SEVERE: Error getConfigured
Jun 5, 2006 6:55:41 PM org.apache.catalina.core.StandardContext start
SEVERE: Context startup failed due to previous errors
Jun 5, 2006 6:55:41 PM org.apache.catalina.core.StandardContext start
SEVERE: Exception during cleanup after start failed
LifecycleException: Container StandardContext[msgstore] has not been started
     at org.apache.catalina.core.StandardContext.stop(StandardContext.java:4466)
     at org.apache.catalina.core.StandardContext.start(StandardContext.java:4371)
     at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:823)
     at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:807)
     at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:595)
     at org.apache.catalina.core.StandardHostDeployer.addChild(StandardHostDeployer.java:903)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at org.apache.commons.beanutils.MethodUtils.invokeMethod(MethodUtils.java:216)
     at org.apache.commons.digester.SetNextRule.end(SetNextRule.java:256)
     at org.apache.commons.digester.Rule.end(Rule.java:276)
     at org.apache.commons.digester.Digester.endElement(Digester.java:1058)
     at org.apache.catalina.util.CatalinaDigester.endElement(CatalinaDigester.java:76)
     at org.apache.xerces.parsers.AbstractSAXParser.endElement(Unknown Source)
     at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl.scanEndElement(Unknown Source)
     at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl$FragmentContentDispatcher.dispatch(Unknown Source)
     at org.apache.xerces.impl.XMLDocumentFragmentScannerImpl.scanDocument(Unknown Source)
     at org.apache.xerces.parsers.XML11Configuration.parse(Unknown Source)
     at org.apache.xerces.parsers.XML11Configuration.parse(Unknown Source)
     at org.apache.xerces.parsers.XMLParser.parse(Unknown Source)
     at org.apache.xerces.parsers.AbstractSAXParser.parse(Unknown Source)
     at org.apache.commons.digester.Digester.parse(Digester.java:1567)
     at org.apache.catalina.core.StandardHostDeployer.install(StandardHostDeployer.java:488)
     at org.apache.catalina.core.StandardHost.install(StandardHost.java:863)
     at org.apache.catalina.startup.HostConfig.deployDescriptors(HostConfig.java:483)
     at org.apache.catalina.startup.HostConfig.deployApps(HostConfig.java:427)
     at org.apache.catalina.startup.HostConfig.start(HostConfig.java:983)
     at org.apache.catalina.startup.HostConfig.lifecycleEvent(HostConfig.java:349)
     at org.apache.catalina.util.LifecycleSupport.fireLifecycleEvent(LifecycleSupport.java:119)
     at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1091)
     at org.apache.catalina.core.StandardHost.start(StandardHost.java:789)
     at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1083)
     at org.apache.catalina.core.StandardEngine.start(StandardEngine.java:478)
     at org.apache.catalina.core.StandardService.start(StandardService.java:480)
     at org.apache.catalina.core.StandardServer.start(StandardServer.java:2313)
     at org.apache.catalina.startup.Catalina.start(Catalina.java:556)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:287)

P45D3 Platinum - System staggers with drive access

Similar Messages

Maybe you are looking for