P4M Freezes with WiFI PCI Card

My PC freezes requiring a reboot.
This has occured since I recently replaced an IDE HDD with a SATA HDD. The PC freezes pretty quicky; sometimes when everything is up and running for a few minutes, othertimes at the XP logon screen
This is associated with my WiFi network PCI card (D-Link DWL-G520). Using an ethernet cable to my router everything works absolutely fine.
Things I have tried:
MOBO BIOS is the latest version
WiFi card drivers are the latest
Used both PCI slots
Used both SATA sockets.
All suggestions gratefully received!!
JMH

Hello,
look for a PCI Latency Timer option in BIOS and increase the value. Try different settings and test again each time.

Similar Messages

Install pb with wifi pci card PC54G

Help,
in my periferal i can see the card but when i try to install MSI drivers from the CD
the install runs til the end,i click finished and then nothing !
the program WLAN utilities is installed but the drivers for the card are not there.
the card is not usable !
on my PCn.2 it installed correctly !
HELP !
my config is
PCn.1
Duron 1600
Abit NF7s
Samsung 2x 512 PC2700
Win XP Pro SP1a
PC n.2
Athlon 2200+
MSI KT4 ultra
noname 2x 256 PC2700
Win XP Pro SP1a

i flashed my motherboard with the latest avilable BIOS
changed of PCI slot (just in case)
re installed the drivers from CDRom
it still doesn't work
i think i' going to try next the technique called "kick in the case"

Which desktop WiFi PCI Card will be able work with personal hotspot signal of iphone 4

which desktop WiFi PCI Card will be able work with personal hotspot signal of iphone 4. I need my desktop to work on WiFi signal emanating from personal Hotspot of iPhone 4.

I think you are running into the following issue.
From: http://support.apple.com/kb/TS2756
Note: If you leave the Personal Hotspot screen or put iPhone to sleep, iPhone only broadcasts the Wi-Fi network for an additional 90 seconds. If no devices join the Wi-Fi network during that time, iPhone 4 stops broadcasting your Wi-Fi network. You can start broadcasting your Wi-Fi network again by tapping Settings > Personal Hotspot.
So, if I understand correctly, if you you leave your iphone on the the Settings --> Personal Hotspot screen, than it shouldn't disconnect.

SP A10 with mini PCI card

Help!
Have had a great deal of success with Toshiba however would like to use it in wireless mode. Have LAN mini PCI card switch yet can not find drivers on computer to enable it.
Any suggestions
Many thanks
Steve

Hi Steve
I'd say that it is likely that You do not have a built in WireLess mini PCI card then. Normally all devices are configured 100% when the machine comes from factory.
And even if the driver is missing You should have a device that was not configured in the device manager and You do not say anything about such a device so I guess there is none.
It is quite common that models are prepared for wireless LAN (like your possibly is) with a WiFi-switch and built in antennas.
best regards
Tom

P67A-C45 b3 don't boot with ITE8212 PCI card

Hello
i was installing my all new motherboard P67A-C45 rev B3 with a core i5 2500K, 4gb of DDR3. No problem for installing all my SATA hard drives as well as Plextor BR writer. Windows seven recognizes everything and everything rules. I have setup the boot priority with plextor and then the SSD drive that have windows 7...Except that as a nostalgic person, i used to keep old IDE hard drives for storing files. For that i use a ITE8212 PCI card in order to have IDE slots. But when pci card is connected (on either of the 3 PCI slots), boot is "freezing". I just have an underscore on the screen and nothing else.
This pci card used to be ok on motherboard without UEFI... is there something that i do wrong ? a specific setup ? an incompatibility ?
Thanks for any help you could give me.

I'm not too concerned with the x8 limitation. Any idea about the video issue itself? It'd be nice to be able to choose which card to boot from without having to take one out or switch them around. I get the feeling that it's always going to use the first card it finds plugged in and just ignore the second card until the OS drivers take control. Mostly I just wanted to confirm that was the case and not just a problem with my own board.
Guess I'll work in getting my 6950 working under OS X, because it's too big to go into E5 without covering some PCI slot I need and also the headers for my power and reset buttons.

Error Code 10 with GPIB PCI Card

PC used: Dell optiplex GX110, lastest Bios release, Windows 2000 SP4, GPIB Drivers version 2.2, Local Admin session.
After having install the driver (without the GPIB)and plug the card, this one is automaticaly recognised by the Os.
But, after the reboot (asked by the OS to validate the installation), the GPIB card appears, in the device manager, with an error code 10 (not started)....
I tried with two (new) differents GPIB PCI Card, two OS (First time with NT4.0 SP6 Drivers 1.7 and now, Win2000 SP4 Drivers 2.2) and with two PCs Dell Optiplex GX110 !
I even tried with a "Ghost" from an other PC (also an Optiplex GX110, with the same model of GPIB Card)
-> I obtain the same error each time !
Help me please..........

Hello,
Could you give me the exact reference of the board (PCI-GPIB, PCI-GPIB+, AT-GPIB, AT/GPIB-TNT...)?
Is the error code displayed on the Windows device manager (in the properties dialog box of the device)?
What is the exact description of the error code?
A PCI-GPIB installation do not need to reboot the OS if the NI-488.2 driver is correctly installed. The board should be recognized in MAX and you must be able to scan for instruments and start I/O communication with the device from test panels in MAX.
Update me as soon as you receive another feedback.
Regards.

Upgrading the G3 /DT with USB PCI Card for Printer Connection

I would like to connect a Brother MFC-9160 laser printer to one of my Beige G3 /DT with Macintosh OS 9.2.2 installed.
There are two ways to do that: USB or Parallel. I don't know if Parallel adapters for Macintosh are available. This is the reason why I am favouring the solution of PCI USB upgrade.
The problem is that the few USB adapters I saw on sale on various French Mac warehouses were all USB 2.0 compliant, and required a Power Macintosh G3 /BW.
I suppose that a USB 2.0 compliant card is also de facto USB 1.1 compliant, but I am not sure. Besides the hardware issue, there is of course the problem of support on a Beige G3 for USB 1.1.
Could you please elaborate on the hardware which would run on a Beige G3? I am open to any friendly advice
Frederic W. Erk

By the way I wonder if it would be possible to
connect to the laser printer through electricity
network. No cables, here because the building in 400
years old and too large. Wireless, he he... Not even
worth speaking about it....
I'm not sure about what kind of electrical wiring you have available over there, or if these kind of products are compatible, but there are some options in the US for using the electrical outlets in a house to create a LAN network. With this kind of network you could use keep the printer on the B&W and turn on USB printer sharing. Printing from OS 9 on the G3 might not work with all printers. That kind of networking equipment is more costly than just adding a USB PCI card to the G3 to use the printer directly, but you might also be able to share a single high-speed internet connection that way. It all depends on what your needs are.
Is this what you were asking about?
http://review.zdnet.com/NetgearPowerline_HD_Ethernet_Adapter/4505-330416-31970278.html

Intermittent issue with Wifi network card.

Nothing can be more annoying than an intermittent issue. Unfortunately it does happen to my MBP. This is the new MBP purchase Jan. of this year. About 2 months ago, the MBP developes a problem. The sympotom is, after powering it on, the Wifi network card sometimes suddently stop working, even cannot be recognized by the system accidently. After the problem arise, I cannot turn on wifi again. The only way to get it back is to restart it. It used to work well with my home network and company network.
I have tried every possible mean to figure out what's wrong with it. Tried SMC reset, PRAM rest. Reinstall a new OS on a new partition (per instruction from Apple support). I hate to say this is a HW issue but support people from Apple did suggest sending it to a service center for a check up.
Before I actually dropping it at service center, I wanna know if someone has experienced that before?
Repeat, it used work well with my router.

senthil,
It helps to describe your setup parameters.
Which antenna(s) do you have? Either 2 internal antennas or 1 external antenna.
How far away and what obstructions (walls - wood/concrete) is the wi-fi router?
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

Acquisition with different pci-cards

hello,
I would like to learn the objectives to take care of in acquisition with two
different pci - cards. Is there something special about configuring the two
cards in the same VI and how can I be sure that the subVIs acquire data
simultaneously?
Please send me some information about bibliography or notes.
thank you

wrote in message news:90o7uf$e5c$[email protected]..
> That is true; however, if you want the acquisitions of both boards
> started at the EXACT same time then you need to order a cable that
> connects to both RTSI connectors on the PCI boards from National
> Instruments. Once you have that cable, then you can call the Route
> Signal VI to route a start signal to both boards and simultaneously
> start them.
A better way is to route scanclock via RTSI from the 'master' to the 'slave'
board.
in this way there is a constant delay (within one channel clock period)
between channels on these boards.
You have to specify on the slave board that the scan clock comes from RTSI.
Don't forget to make the channel clocks identical.
Read the help of AI Clock Config (see inside AI start.vi)
You need 2 calls to AI Clock Config on the slave. One to set the Scanclock
and one to set the Channel clock)
If you need more accuracy you also have to route the board clock (20Mc) via
RTSI.
Start the slave first, so that it is ready to receive clocks from the
master. Then start the master.
>
> In article <90ham7$j4p$[email protected]>,
> "Fan Zhang" wrote:
> > to your question, no. Nothing special to configure two pci cards at
> the same
> > time in one program. You can distribute two IDs to them then call the
> one
> > you would like to call in your application.
> >
> > "gkonstan" wrote in message
> > news:90ggtt$i28$[email protected]..
> > > hello,
> > > I would like to learn the objectives to take care of in acquisition
> with
> > two
> > > different pci - cards. Is there something special about configuring
> the
> > two
> > > cards in the same VI and how can I be sure that the subVIs acquire
> data
> > > simultaneously?
> > > Please send me some information about bibliography or notes.
> > > thank you
> > >
> > >
> >
> >
>
>
> Sent via Deja.com http://www.deja.com/
> Before you buy.

Memory issues - kernel panics / system freezes with 1Gb Memory Card

I've recently updated my PowerBook OS to 10.4.7 and now more recently 10.4.8.
Prior to this, i had been running a pair of pc2700 memory cards (1x1Gb + 1x 512Mb) bought from crucial technology on 10.3.9 with no problems.
During the upgrade, i experienced complete system lock ups and kernel panics. pulling the 1Gb card resolved the problem.
So i thought it could be duff memory (it happens). I ran hardware checker, both long and short tests, ran memchecker from single user and there was no reported errors although i was still getting crashes.
I returned the memory to crucial and they replaced it and then i went to reinstall memory in the pb.
Once reinstalled, problems re-emerged. Both System profiler and iStat pro show both memory sticks as ok. both are pc2700 DDR.
i tried just the 1 Gb stick in alternate memory slots. with the memory in the lower slot i was getting system freezes, in the top slot i was getting kernel panics.
I've pulled the 1Gb and reverted to 768Mb (512Mb lower (crucial)/ 256MB (apple) upper) and i'm back to normal.
Now what?
As my mac is getting on, i'd like to get as much RAM in it as i can, ideally the 1.5Gb /2Gb which it can support. I'd be suprised if it could be the memory stick being duff (2 duff in a row?), its not a faulty memory slot as system profiler is showing that its full.
Any suggestions? Anything to do with how 10.4.8 handles the memory addressing?
Any help would be appreciated.
PowerBook G4 1Ghz FW800 Mac OS X (10.4.8)

I've had that problem, too. I found out that it was one of my memory modules that were broken.
I'd say pop back in your other memory module, then get out your PowerBook DVD and stick it in Restart your PowerBook while holding down the Option Key on your keyboard until some buttons start to show up on your screen.
Select the Hardware Test one, then click the Arrow button. It'll boot into a utility and you can run a hardware test that includes checking your memory.
If any of your memory is bad, it'll show up like "**ERROR ERROR**" and give you a code.
After you've identified the hardware problem (hopefully just the RAM), then you can go to Crucial's website and fill out an RMA request to have the memory replaced. I'm pretty sure Crucial has a life-time warranty on their memory products.

Photoshop and Lightroom freezing with supported graphics card

Good Morning,
I'm looking for some help to correct a problem. I'm sending this request to Adobe, Asus, Corsair, and Intel. I'm a professional photographer and this is my new computer to support the Nikon D800.
Problem:
When working in both Photoshop (CS5) and Lightroom 4 my computer is freezing and I'm having to do a kill restart to unfreeze the computer. This is happening when doing simple processes like panting with the air brush in Photoshop.
I have to correct this issue it is my livelihood. Which of the components do I need to replace and with what specifically?
Computer:
i7 3970k CPU Intel
Asus Sabertooth X79 motherboard
Corsair 8- 8GB for a total of 64GB of ram (un-buffered)
Two drives both Western Digital
Graphics card is a Adobe supported ASUS GeForce GTX570
Windows 7 professional
Attempted corrections:
Up dated graphics card drivers, and Windows, check and unchecked Open GL Draw but it freeze in both setting. Follow all of Adobe's set up guide lines. Follow the recommendations from NAPP. Had some bad sticks of ram waiting on Corsair RMA replacement. Computer has 16 GB of ram in it at the current time but the freezing characteristics are the same with 64 GB and 16 GBs of ram.
Thank you in advance for your help,
Mike Boatman

I am running Win 7 Prof on a Xeon processor with 12 GB RAM. Occasionally I experience random freezes of my system but as far as I can tell neither Lr nor Photoshop are involved.
I never found a cause since my Event Viewer does not give any error messages.
I have searched the Win 7 forum at http://www.sevenforums.com/#windows-7-help-support
and found this: http://support.microsoft.com/kb/2575077
They say they fixed it with a hotfix but it seems it still does occur. My last freeze was on May 3, 2012.

Synchronised DAQ with 2 PCI-cards

Hi folks,
we want to use two (2) synchronised PCI-6071E DAQ cards in one PC. At
the moment we use software triggers. Is it possible two get the
software trigger for device 2 from device 1? Or do we have to use an
external trigger what is not impossible but it needs more work? Do any
DAQ vi exist for two DAQ devices?
Thanks for help, Felix
Felix Tiefenbacher
Swiss Federal Institute for Snow- and Avalanche Research
Avalanche Dynamics
Fluelastrasse 11
CH-7260 Davos Dorf
Tel: +41 (0)81/417 02 53
Fax: +41 (0)81/417 01 10

Software triggering in this case might be possible, but the better solution is to start things with a hardware trigger. Any computer running a commercial OS will have varying amounts of latency that will make reliable software triggering problematic. What's more, the faster the event is that you are trying to capture, the worse the problem gets--and sliding snow is very fast.
I understand that external triggering is more work, but you get much better results. Also the only tricky part will be generating the trigger. The code for a hardware triggered acquisition isn't any more complicated than software triggered code.
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

MDD with SATA PCI card, what is largest drive possible?

I have recently bought a Sonnet Tempo PCI SATA card for my MDD, is there a maximum size to the SATA HDD which I can attach to this card?
I want to use it mainly to store videos etc.

If the drive is to ever be bootable, 2TB is the largest partition that you can use.
Not sure what Sonnet has tested with that card, but the Firmtek controller that it carries will support 2 TB for sure.

No boot with mini pcie card installed

I have a wind PC and I am trying to install a mini-pcie video decoder into it. I installed the card and the system will not boot. Take the card out, boots up fine. Thought maybe a bios update would do it. Flashed the bios, boots fine without the card, no boot with the card. Am I missing something?

Quote from: sjay on 13-April-11, 04:32:46
There are plenty of things you can do with it, it can be an HTPC, a server, a mobile work platform.
After all, it is a Computer and there are plenty of people in the world who don't even have clean water or food at all.
I'm sure you can find a use for it, perhaps gifting it to someone who isn't as well off as you.
You'd be surprised how good it feels to make someone who is less fortunate really happy.
I've given away many PCs, and I'm far from wealthy! When people I know buy new PCs I take their old ones off their hands, upgrade them, clean them up and give them away to people who can't afford one. I've given away a few on mine too. Just last week I donated my old laptop to a woman who is fighting cancer.
This machine was going to be a high def HTPC, that's not going to happen. Since I can't afford anything else I am a bit bummed out. Working three jobs to pay the bills, I just wanted to do something nice for me for a change. Once in a while I even grab an old PC from work and redo it for someone. Some of our wealthier customers just leave their old PCs with us when they pick up their new ones.

Safari freezes with WiFi connection working properly

Hello,
While using my Macbook Air, (I bought it in Nov2012, so.. supposed to be brand new!!) and trying to connect in the internet, using Safari and Wifi, it usually freezes and won't load any pages.
I did check my Wifi router and it works fine. I have 2 iPhones and 1 Ipad connecting to this Wifi router and these devices are working fine.
The problem is when I turn on Macbook air, it shows that the connection with the Wifi router is ok, I got all bars in the signal, and then when I tried to open Safari, it frezees in the main page and won't load it. (The rest of the devices continue working fine.. )
I tried some of the posts here.. like enable/disable plug-ins, disk repair, deleting plist, upgrading my OS and also upgrading my Safari (there no newest version available to be downloaded for both Safari and Mac OS).
Also, I tried the "Assist me" option... and it shows like my Internet is not working.. all green spots until ISP.. then red light at Internet test..
but it is working for all other computers in the same Wifi.
My best guess is that some configuration in the Network part is not properly set up.. or even my Safari configuration is messing up my Internet connection when I tried to load facebook for example.
I got it working for a while.. when I had all the other devices turned OFF.. (like Iphones and Ipad) , and then I had to reboot my Macbook Air.. then it works for some minutes.. but then, suddenly, it stop working. (Seems that it's trying to load some Java Scripts in the page and it keeps trying and trying.. )
Any help will be much appreciated.
Many thanks in advance.

So this not being your router's problem let's conclude that iPod is the culprit! You were saying that it worked properly until recently so it might be a iOS related problem. Try restoring the firmware using iTunes! But before, backup everything and proceed through it! After restoring, iTunes will ask about restoring the data or setting it up as a new one - DON'T RESTORE. Let the backup be there, try setting it up as new. Then verify the wifi connectivity, if all goes right then you can restore from backup! If all else fails, your device may require an authorised personnel attention asap! Cheers!

P4M Freezes with WiFI PCI Card

Similar Messages

Maybe you are looking for