P50t-bst2n01 Laptop Stopped working

Hi so I was taking notes on PowerPoint for an exam with my laptop plugged in and all of a sudden the laptop shut down and will not turn on any more. The laptop charger is still working, I had it tested at a computer store, the computer has no lights when pressing power button and when plugging in the charger. I'm not sure what to do. I can't retrieve my hard drive either since that would void my warranty. I don't want to send my laptop to toshiba without backing up my files since they will reset the whole laptop.

Try these suggestions:
What can I do if my Windows 8 laptop won't start?

Similar Messages

  • Laptop stop working while updating bios

    Lately when i turn on my laptop, the screen is black, caps lock and scroll blinking twice, i read that i should update my bios.
    The problem is when its updating ( insydeFlash is running half way ) i noticed my laptop stop working.
    The window is on, i can see everything on screen, even the sound of my laptop, but i can move the mouse, well >.>
    I dont know what should i do? Should i turn off my laptop?

    , Hello and thanks for posting on the HP support forums.  When it comes to a bios update the rule is if it isn't broke don't fix it.  If it is locked and not responding then the only choice you have is to do a hard reset first. HP Notebook PCs - Performing a Hard Reset or Forced Reset Once you have done that here is a link for doing a bios recovery. HP Notebook PCs - Restoring the BIOS Thanks again for posting and have a great day.

  • Scan on my CM2320fxi from my windows 8.1 laptop stopped working

    I have the scanner software installed for my CM2320fxi on my hp laptop but for some reason it has stopped working. The scan function on the laptop times out and says it can't locate the scanner and the MFD can't recognise the laptop. There is no problem accessing the scan function from an older XP machine, but I can't seem to get it working from the newer Windows 8 machine.
    Help much appreciated

    Are you able to ping the remote system by name? It sounds as though you are connecting to VPN but are unable to resolve the names of the host network. A few things that I would think of:
    If the home system is not on a domain and the work system is, you may need to use the Fully Qualified Domain Name (FQDN). For example, instead of
    computer you would enter computer.domain.com.
    You may want to check if your VPN connection is configured as a default gateway, otherwise if your home and VPN network have the same IP address range you may be experiencing a conflict.
    See the instructions provided here.
    You also may want to check the DNS settings for the VPN connection to ensure that it is finding the DNS server for the remote network and thus is able to resolve the hostname.
    You may want to try connecting Remote Desktop via IP address to determine if the issue is with name resolution (DNS) or connectivity.
    Brandon
    Windows Outreach Team- IT Pro
    The Springboard Series on TechNet

  • HT1941 My laptop stop working all of a sudden

    How would I know if my laptop still under warranty and why it stop charging and power on all of a sudden?

    Warranty
    Click  in the menu bar.
    About This Mac > More Info..
    Click "Services" tab at the top, then click the arrow beside
        "Check my services and support status".
    Battery charger
        Reset SMC.     http://support.apple.com/kb/HT3964
        Choose the method for:
        "Resetting SMC on portables with a battery you should not remove on your own".
    If this does not help, contact Apple.

  • Volume on laptop stopped working

    HP Pavilion dv7 Notebook; Windows 7 Home Premium
    No upgrades...was working fine a few days ago 

    Hi,
    Re you talking about the Quick launch volume buttons at the top...
    You can try this if it is the quick launch buttons:
    Use Hard Reset to Resolve Hardware and Software Issues
    Note:
    If you have HP Support Assistant installed on the computer(The Blue Question Mark) then open it ==> Complete all pending Updates & Tuneups==> Restart and Check. It may solve your problem
    Although I am an HP employee, I am speaking for myself and not for HP.
    **Click on “Kudos” Star if you think this reply helped** Or Mark it as "Solved" if issue got fixed.

  • Touchpad stopped working. Laptop won't turn back on.

    My laptop stopped working last night (won't turn back on). The touchpad stopped responding. I did a manual shutdown by holding down the power button until it turned off - it won't turn back on when I press the power button.

    @jamesfl621 ,
    Hello and thank you for posting on the HP support forums.  Try doing a hard reset with your notebook.  
    Here is a link to help you with this.
    Performing a Hard Reset or Forced Reset
    If the hard reset does not get you any response contact HP phone support for repair options.
    Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    Thank you again for posting and have a great day.
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    D5GR
    I work on behalf of HP

  • [Ubuntu, Windows 8.1] Touchscreen stopped working.

    Hello!
    From about 1 year I'm lucky owner of Lenovo Idea Pad Flex 15 Laptop. I love it!
    Today touchscreen of laptop stopped working after reboot from Ubuntu 14.04 to Windows 8.1. On both system screen is detected but, there is no input. I tried to turn off usb power saving on Win 8.1 and reinstalling all HIDs, without any success. On Ubuntu I tried to calibrate screen - still no luck. If applicable there is dmseg output:
    dmesg | grep eGalax
    [ 3.443718] usb 2-1: Product: eGalaxTouch EXC7910-1026-13.00.00
    [ 3.443720] usb 2-1: Manufacturer: eGalax Inc.
    [ 27.549122] input: eGalax Inc. eGalaxTouch EXC7910-1026-13.00.00 as /devices/pci0000:00/0000:00:14.0/usb2/2-1/2-1:1.0/input/input7
    [ 27.549752] hid-multitouch 0003:0EEF:A111.0001: input,hiddev0,hidraw0: USB HID v2.10 Device [eGalax Inc. eGalaxTouch EXC7910-1026-13.00.00] on usb-0000:00:14.0-1/input0
     So, how to make screen working again?
    Cheers, Damian Herman

    Hi，
    A VPN 720 Error can occur if your server's VPN configuration doesn't point to a valid DHCP server on its network.  The result is your client can't connect since it doesn't have a valid IP address to use.
    On the VPN Server, go to "Routing and Remote Access" under "Administrative Tools" and go to the "DHCP Relay Agent" configuration.  Check the DHCP server IP addresses that are listed for correctness
    Regarding to restore point as mentioned in the post, do you have a anti-virus software installed? if you have, I suggest you temporarily disable it, then try restore point again.
    For that specific update KB2920189, any error messages prompted when you uninstall it, you can also check the cbs log (Windows\logs\cbs), for detailed information.
    Yolanda Zhu
    TechNet Community Support

  • Why would my home sharing stop working

    my home sharing from my desk top to my laptop stopped working. can someone tell me why it stopped. cant get my itunes library copied to my laptop

    I am having the same problems now as well. Just did the OS update this morning. Before the update, I could view purchased TV shows on my Apple TV and now, I get a message saying to access your iTunes library on Apple TV, turn on Home Shairng in itunes. Have done that, and restarted everything. Nothing works so far.

  • HP Pavilion DV6 Beats Audio speakers stopped working

    the speakers on my HP Pavilion DV6 Beats Audio laptop stopped working and there is absolutely no sound coming out from it. Please help!
    This question was solved.
    View Solution.

    Get your full Model number or Product number from the Service Tag attached to bottom of laptop (probably  under battery)
    How Do I Find My Model Number or Product Number
     Once you have the info, use the button at top of this page titled "Support", then click "Download drivers" from the menu. Enter your Product Number. After entering PN click 'Go". On the next page use the dropdown menu to select your Operating System, click Next. A list will populate with drivers/software.
      Download & Save the latest Audio driver.Go into Control Panel,Programs & Features -Uninstall IDT software.Restart the laptop. After Windows loads, install IDT audio using the downloaded file.
    If still no sound,try a hard reset.Disconnect all external devices first.
    1-remove power cord and battery
    2-press power button for 30 seconds
    3-reinstall only power cord for first startup.
    4-power on
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • Wifi stopped working. Not even manually.

    Hi,
    I've no idea, where to go from here. Wifi on my Thinkpad Edge 13 Laptop stopped working (meanwhile a few weeks ago). Until then I had it running with NetworkManager and everything was fine. At home it is a WPA-connection. Still works without problems on mobile and kids' laptop (ubuntu).  "iw wlan0 scan" shows hardly any networks although there're loads around. That used to be different before. At work, an EAP-connection works well under NetworkManager. Now I removed NetworkManager in order to try manual connection.
    When I start wpa_supplicant, I get "device or resource busy" and the connection fails. My conf-file consits only of the output of wpa_passphrase. The corresponding dmesg  shows several
    [ 1838.093841] wlan0: authenticate with 00:24:d1:79:a7:7d
    [ 1838.103460] wlan0: direct probe to 00:24:d1:79:a7:7d (try 1/3)
    [ 1838.206524] wlan0: direct probe to 00:24:d1:79:a7:7d (try 2/3)
    [ 1843.108643] wlan0: deauthenticating from 00:24:d1:79:a7:7d by local choice (reason=3)
    After this, the interface comes down by itself. The output of dmesg is the same with NetworkManager. I've also tried wicd and netctl without success. I have ABSOLUTELY no idea how to continue debugging and appreciate any comment that might give me a new direction.
    Question on the side: when I reinstall NetworkManager and enable it under systemd, do I have to enable dhcpcd under systemd as well or is that taken care of by NetworkManager?

    Thank you for helping me out. When I tried again today I couldn't even get my interface up due to RF-kill. Installed rfkill (was there before when I tried wicd) and removed the soft block on phy0. Now these are the services running:
    $ sudo systemctl -t service
    UNIT LOAD ACTIVE SUB DESCRIPTION
    avahi-daemon.service loaded active running Avahi mDNS/DNS-SD Stack
    cronie.service loaded active running Periodic Command Scheduler
    dbus.service loaded active running D-Bus System Message Bus
    [email protected] loaded active running Getty on tty1
    polkit.service loaded active running Authorization Manager
    slim.service loaded active running SLiM Simple Login Manager
    systemd-journald.service loaded active running Journal Service
    systemd-logind.service loaded active running Login Service
    systemd-modules-load.service loaded active exited Load Kernel Modules
    systemd-remount-fs.service loaded active exited Remount Root and Kernel File
    systemd-sysctl.service loaded active exited Apply Kernel Variables
    systemd-t...es-setup.service loaded active exited Recreate Volatile Files and D
    systemd-udev-trigger.service loaded active exited udev Coldplug all Devices
    systemd-udevd.service loaded active running udev Kernel Device Manager
    systemd-update-utmp.service loaded active exited Update UTMP about System Rebo
    systemd-u...sessions.service loaded active exited Permit User Sessions
    systemd-v...le-setup.service loaded active exited Setup Virtual Console
    udisks2.service loaded active running Disk Manager
    upower.service loaded active running Daemon for power management
    Nothing network as far as I can tell. Then I get wlan0 up with "sudo ip link set". Starting wpa_supplicant I get this output (as before):
    Successfully initialized wpa_supplicant
    wlan0: Trying to associate with 00:24:d1:79:a7:7d (SSID='UPC009875' freq=2412 MHz)
    ioctl[SIOCSIWFREQ]: Device or resource busy
    wlan0: Association request to the driver failed
    wlan0: Authentication with 00:24:d1:79:a7:7d timed out.
    wlan0: CTRL-EVENT-DISCONNECTED bssid=00:24:d1:79:a7:7d reason=3 locally_generated=1
    After I quit with Ctrl-C the interface is down again...
    Looks like the ioctl... is coming in my way, I'll try to figure out what that is.

  • Satellite X205-SLI1 - VGA fand stopped working

    The VGA fan on my laptop stopped working and I haven't been able to find another one other than from the states.
    Does anyone know if its possible to buy a new fan for this laptop in the UK?

    Hello
    I dont know if its possible but why you dont ask the ASP in your country? They will know that ;)
    On the Toshiba website you can search for the nearest ASP:
    http://eu.computers.toshiba-europe.com => Support & Downloads => Find an authorized service provider
    If you have more questions please let us know.
    Greets

  • S415 Touch: WiFi sometimes stops working

    Randomly, the wifi for this laptop stops working. It says it's still connected but the internet cannot be accessed unless I reset the wifi. This happens pretty often, it can happen from once every 10 minutes to every 2 minutes. This proves to be an issue because I cannot maintain a stable internet connect for a long period of time. 
    I've already tried the suggestions for this such as going to device manager and disable to option to turn off the network adapter and removing/reinstalling/updating the network adapter with the file provided in the suggestion, none of these methods work, as I still disconnect at random intervals. Is there anything I can do to fix this?
    Also the only thing I haven't tried is disabling WMM, because when I tried to find it under the configuration of the Router it wasn't there.

    bravebird201,
    Thank you for providing these information. What we need to do right now is to check if the current drivers for your wireless adapter is up to date.
    * Qualcomm Atheros AR9485 Wireless Network Adapter : check driver details. click on this Link for software and drivers update.
    * Linksys E1200 check if the router is set to Mix Mode, if it is set to Mix Mode you need to set it on wireless N. the wireless channel needs to be set on 11 and it should be on a 2.5 GHz frequency.
    * check the other laptop if it runs on a wireless G & N modes.
    Article Using Wireless G and Wireless N devices on a Home Network Link
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

  • Wi-Fi switch stopped working

    Hi,     After upgrading to windows 10, Wi-Fi button on my laptop stopped working and unable to connect Internet. Afte trouble shooting getting message that Wireless capability is turned off, press wi-fi button on laptop, pressed it but remain orange color. Please help me to solve the problem.

    I'm having the same problem on my HP Stream 13 c077nr

  • Problem with iTunes. I have Windows 8 on a new laptop. Installed latest version of iTunes. Can play music in My Library but when I click on Itunes Store I get the message "iTunes has stopped working. A problem caused the program to stop working correctly.

    I have a new laptop with Windows 8 as operating system. Installed latest version of iTunes ontop computer. I can play music in My Library but when I click on iTunes, I get the message " iTunes has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify if a solution is available."
    Anyone know what is the cause and if there is a resolution? Have tried to re-installing iTunes and have also tried restoring laptop to an earlier date.

    iPad not appearing in iTunes
    http://www.apple.com/support/ipad/assistant/itunes/
    iOS: Device not recognized in iTunes for Mac OS X
    http://support.apple.com/kb/TS1591
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    iTunes for Windows: Device Sync Tests
    http://support.apple.com/kb/HT4235
    IOS: Syncing with iTunes
    http://support.apple.com/kb/HT1386
    Apple - Support - iPad - Syncing
    http://www.apple.com/support/ipad/syncing/
    iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi Syncing
    http://support.apple.com/kb/ts4062
    The Complete Guide to Using the iTunes Store
    http://www.ilounge.com/index.php/articles/comments/the-complete-guide-to-using-t he-itunes-store/
    iTunes Store: Associating a device or computer to your Apple ID
    http://support.apple.com/kb/ht4627
    Can't connect to the iTunes Store
    http://support.apple.com/kb/TS1368
    iTunes: Advanced iTunes Store troubleshooting
    http://support.apple.com/kb/TS3297
    Best Fixes for ‘Cannot Connect to iTunes Store’ Errors
    http://ipadinsight.com/ipad-tips-tricks/best-fixes-for-cannot-connect-to-itunes- store-errors/
    Try this first - Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.
    This works for some users. Not sure why.
    Go to Settings>General>Date and Time> Set Automatically>Off. Set the date ahead by about a year.Then see if you can connect to the store.
     Cheers, Tom

  • I can't open Itunes on my laptop. "Itunes has stopped working. A problem causes the program to stop working correctly. windows will close the program and notify you if a solution is available" is the message. what is the problem here?

    I can't open my Itunes program in my laptop computer with windows 8. the message is "Itunes has stopped working. A problem causess the program to stop working properly. windows will close the program and notify you if a solution is available". I reboot  the machine, Uninstall and re install the  Itune program, stilll the same message pops up.

    The first thing to try is System Restore to take you back to a point in time when it did work. If that is not successful, create a new user on the computer. log in with that and see if ID will start. This will tell us if the problem is in the system/program or the user account.
    If it works in a new user account, see Replace Your Preferences and in addition to replacing the prefs, empty the InDesign Recovery folder that will be in the same location and the InDesign SavedData file.

Maybe you are looking for