P55A-GD65 Can not see Sata III drive

I can not get the bios to see my 250gig sata III. I have it connected to sata#7 white connector.
I tried to first see it, no go. I am trying to fresh install w7 hp upgrade 64bit to my new sata III drive. I can not find the drive. I do not know if it is bad or what?
I set Integrated peripherals- sata 6g/s controller mode to ahci, and in on-chip ata devices raid mode set it to ahci. I tried to install w7 from disc. It just Says I have made a hardware change. Try to do a repair start or start as normal. Then said my boot sector was messed up. I pressed reset and got into bios and set it all back to ide mode.
It would not start normal. But from page it says try w7 disc etc. I told it to start windows normally it did, I have rebooted So I guess it fixed the boot sector..
I am not sure what to do. I can not find the drive, and no place in my bios can I find the sata 7-8 connectors. they are listed as 1-6 and 9.. everything skips 7-8. I am in w7 now. I could do the reg tweak. I want to fresh install w7 upgrade on my new sata III drive. then nuke this sata II and make it a storage drive..
Maybe I need to press a key with w7 disc in during restart. I can not figure out how to make Let me reinstall w7. I did press F6 but I did not know what to do. Upgrading from xp was pretty easy. This sata III and mobo and w7 is a head ake. It is no simple instructions no place to make this stuff work right. Ha ha the manual is no help either.
I do not know if maybe the drive is bad or not. I never had to do this stuff in bios just to install a drive, and then controllers 7-8 show no place. I do not know what to do..

Follow up.
My cam batteries are acting up. Sorry not better photo'. The second photo. I changed out my speakers set up etc, and its photo was with our cam corder, it has no flash.. The top 5.25 bay filter is a test. I need better materials to make a better 1, but it works well, not so pretty tho. If I relax the pantyhose, It looks a lot better, is black. You can not see through it, but less air flow...
The blower box mod I made from a gutted opt drive, uses the rest of the 5.25 bay cage as the lower sides of the box. The top side, the actual gutted opt drive, I used my zig saw, cut along the sides from the top and back end. So it was free to bend down. You can not see from the photo, but it is down just above the top of the mobo tray, and extends out past the back side of the 5.25 cage. With both downward blowing air and is more compressed or moves faster because the top is bent down etc. I cut off the access on the side so not to go past the 5.25 cage. Made a face plate to mount the fan [can crank 103 cfm] to the other end of the gutted opti. It is easy in out, uses my normal case mounting gear, and is flush with the front of the case. The filter and or front cover are separate. I need to make a better filter frame. But it works. I like it for now.. My twin p160 case has the same set up, but using a 80mm face plate and fan, and being a normal 5.25 opti drive as it base, they can go case to case, most all cases have a 5.25 cage, so. I could use this on the lian li case below and just mount a normal fan filter right to the face plate..>>
Build #2, my buds rig, was a snap to build. Not 1 fault in the entire build from- view reliability history. The large case was nice to work in.. Both systems running great and with AHCI support.
Ha ha I got them running perfect in spite of ?
MSI P55A-GD65 v1.1 bios 1.3. I5-750. W7 64 bit.
Crucial 4GB kit CT2KIT25664BA1339 9-9-9-24 T1 1.5v
Corsair CAFA50. ASUS ML248H 24". Corsair TX 650w.
LIAN LI PC-A70F Black +120mm Intake Mod. EVGA 9800GT.
Samsung DVDRW IDE. LOGITECH X-530 BLK5.1. AC MX2.
WD2500AAKX Sata7C: WD3200AAJS Sata1E: Fios15\2mbps.
Good to go..>
See ya.

Similar Messages

Y ? i can not see my DVD drive in favorites, on the left side. TQ.

y ? i can not see my DVD drive in favorites, on the left side.
TQ.

On the left side of what, the Finder?
Open Finder Preferences, click on Sidebar and see if CDs & DVDs is selected under devices.

Can not see TC hard driver using istat pro or activity monitor

I upgraded the firmware of TC to 7.4.1 yesterday, but I found the transfer speed was too slow and I noticed that I can not see the TC condition using istat pro or activity monitor. So I downgraded the firmware to 7.3.2. Now the transfer speed is fine but I still can not see the TC hard driver in the istat pro or activity monitor.(but I can access files in the TC hard driver normally)
Can anyone help?

I couldn't see my TC hard drive in iStat pro until I actually mounted the TC's Airport Disk using the Finder 'Connect to server' dialog. iStat Pro only gives me Used and Free GB for my Airport Disk. My TC is an old 500GB upgraded to 1TB running 7.4.2 firmware.
As to checking the temperature, I'd be interested too. I have a digital thermometer taped to the top surface of the TC and it is reading 46C with an ambient of 17C. The TC sits on top of a cupboard with clear space around, and I am resting it on a spacer which lifts it 12mm clear of the cupboard to give it the best ventilation. The TC has been doing a long (08:00 - 21:00) Time Machine backup today.
Sayling

Can not see Oracle ODBC driver in Ms SQL Server 2007

Hi
I am trying to export an ms sql server table to Oracle using the Ms SQL Server 2007 export wizard and the only driver I found in the list is Microsoft OLEDB Provider for Oracle.
I already installed Oracle client and I addedd an ODBC conenction of the datasources Why can I not see the Oracle ODBC driver?

Which version of Oracle and what kind of Client Install
Are you sure you did the full Client Install which will have ODBC ?
Execute odbcad32 and look under Drivers Tab for Oracle ODBC Driver

I can boot up my macbook pro but all i see is the wallpaper and the dock and the toolbar at the top. I can not see my hard drive or anything else. please help

Please help. I can boot up my macbook pro and log in but after that all i see is the wallpaper, toolbar and the dock. In the dock it has 2 ? where the doc and download folders should be. If I open up a new finder window it doesnt show anything in there no hard drive or anything. If anyone konws how to help let me know please and thank you.

Agree with baltwo, though even if you have saved the install app I wouldn't use it unless its been used to install a known good copy of the OS already.
In your case, that probably means start fresh:
Restart the computer, holding down 'command' and 'r'. When the recovery disk window shows, choose 'Reinstall Mac OS X'.

Can i install sata III hard drive?

Hi, i've an iMac G5 20" iSight with an intel core duo 2ghz. I would like to know if i can install a sata III hard drive like 128GB Crucial m4 2.5" SSD.
Thx a lot.

First, you do not have an iMac G5. G5s are PPC machines, but yours is an Intel model.
You can install a SATA III drive but I would not spend the money since your model only supports SATA I or SATA II depending on which model you have. I would also be careful about using Crucial SSDs because they may not all work in a Mac. I would get your SSD at OWC instead. You will find their equivalent product for SATA I or SATA II here. I have two of these drives, and they are excellent.

Can not see hard drive on desktop after reinstalling Mountain Lion

I have erased my hard drive and reinstalled Mountain Lion 10.8.4 and now I can not see the MacIntosh HD on the desk top. Downloaded the most recent updates and restarted but still do not see the hard drive on the desk top. Any ideas?

Open Finder preferences and on the general tab check Hard disks for Show these items on the desktop.

I can not see my external hard drive that is hooked to my airport extreme

I have hooked my iOmega 1tb hard drive to my airport extreme but can not see it on my macbook pro. need help to set this up

This is unsupported by Apple. You must configure Airport Utility to turn enable File Sharing of the drive in Sharing preferences and in the AEBS configuration. Then you have to "mount" the drive on your Desktop by selecting Connect To Server from the Finder's Go menu.

Can't see external hard drive after error code -36

Hi, was copying iphoto data from an WD My Passport 750GB external hard drive to my MACBook when the system said it could not complete the copy as it had encountered a problem and indicated error code -36. Now I can't see the external drive (or any data) on any computer. I have tried 3 different MACs to no avail. The drive makes a soft beeping noise but then stops but the light stays on.
Any ideas on how I can get access to my data??

Make sure the cable is securely seated on the device side.
If that's not the problem, then either the drive mechanism or the enclosure has failed. If you don't have backups, you'd better hope it's the latter. Remove the mechanism from the enclosure and install it another enclosure. You can buy fairly inexpensive USB docks that a SATA drive drops into with no need for disassembly.
Failing that, your only chance is to send the drive to a recovery service such as Drive Savers. They disassemble the drive mechanism in a clean room and mount the platters in another drive. Cost will be in the 4-5 figure range, and the results are uncertain.
If you don't have backups, you don't have data.

SATA III drives?

Does anyone know if and when SATA drives will be updated to the next spec of 600MB/sec for SATA III drives....todays standard is 300MB/sec for SATA II drives.
Thanks-

You can use the Marvell but those wont show in the Rapid Storage Manager. That is just for the Intel controller. You have to set the Marvell
controller to raid in the bios and then install the raid driver and software for the Marvell. I believe their Raid Management install might be separate from the driver install.
You can use both the Marvell and the Intel 6Gbs ports. You will just have to use different utilities to manage them. Keep in mind though that 6Gbs does not show a performance gain on mechanical drives unless you have them on a SAS controller in a large raid. Only SSD drives really show a performance gain.
Eric
ADK

Can not see wireless TM in disk utility or desktop.

Am I running a TM Airport (router) it runs great, I love everything about it and the backups have no issues.
But I wanted to partition my 500mb drive on my TM yet for some reason I can not see the drive either on my desktop or in disk utility. Is there some setting I need to change somewhere else to be able to view this wireless drive and configure it? I looked via Airport Utility and the only option there is to archive or erase it, at least that can see it.
When the backup starts I do see a mounted drive show up.
Any ideas?

It does not show up because when I am not backing up, it gets disconnected...

Can not see all the clips in large Icon view in my bin

I arranged my clips in a bin in large Icon view but i can not see all the clips in the bin while in that mode. I see the clips when in list mode or when i drag them out of the bin into the main bin. As soon I drag them back in large icon view bin they do not show up, when going back in list view they are there.
Any idea
Also my daughter accidently pulled the electrical plug, which turned my external hard drive off. So the media was off line. I hit reconnect the clip but the clip does not show as connected in the bin it keeps the Media offline icon but putting the clip in the viewer or time line it plays it. So the clip is reconnected
hope anybody can help with those two issues thanks

Nick
thanks for your message it helped to show the clips. Here how I solved it. I put the clips i could not see in large Icon view, to the Project folder. Even in the project folder I was only seeing the clips with Thumbnail in list view. When i hit large Icon view the clips disappeared, and they could not have been lower down as i only have about 5 folders in the project. I then clicked arrange the clip by name and they showed up again. Like that i dragged the clip back in to its bin and it showed up. The reason for going back and forth I arranged the clips manually in the bin before and when hitting arrange by name it spread them to far apart and put the clips not in a sequence I liked.
for the second part I followed Neil's suggestion it worked.

Can not see Stored Procedures owned by "Code Owner"

Post Author: BinChen
CA Forum: Deployment
I am using Data Source defined with "CR Oracle ODBC Driver 5.0" in "Data Source (ODBC)".
But in Crystal Report XI, I can not see CodeOwner when I can created a new connection using ODBC (RDO).
I can see CodeOwner and all SP defined under it when I use "Oracle Server" directly or use sqlplus.

Post Author: BinChen
CA Forum: Deployment
I'm using Window XP with Oracle 10g2R
To be more clear,
I have an ODBC Data Source defined as "DEV" and when I created a connection using ODBC, I can only see some database account section like: APP, APPREF, PUBLIC, SYS, SUSTEM. But I can not see CodeOwner.
If I connected without using ODBC, I can also see CODEOWNER and then all its stored procedures.
So why I can not see Stored Procedures defined under CODEOWNER using ODBC?
I have an exsiting report, even I can not see CODEOWNER, but I have no problem to run and preview the report also to "verify database".

Imac will not see my hard drive on start up, wants to start from network start up disk that does not exist. How to get rid of it? So there is just one choice / my hard drive.

I have a Intel duo Imac. Everything has been running relatively smoothly for a few years now. All of a sudden my computer will not start. I get the flashing folder with a question mark.
When I go to Start up disk in my system perfernces while the computer is on. I see 2 possible choices. One is my hard drive with the operating system shown. The other is a non-existant Network Start up disk with a question mark in it ( looks like a hard drive with a question mark and it say's its a "network start up disk).
All I think I want to do is get rid of the Network startup with the question mark. I can not find anywhere how one can just remove an old or non existant start up disk without reformatting.
I believe this came from a clients hard drive who had a network system on it. We no longer have that drive. It no longer exists. But a latent icon shows up in start up disk.
When I go to change the start up disk. I can change it to either the hard drive or the network with the question mark. But when I select my hard drive and then got to restart the computer. I get the flashing folder with a question mark on start up. I have also seen the flashing globe a couple times.
When I attempt to run disk utility from may install disk ( holding down "C" on start-up ). Disk utility does not see my hard drive. Just the Apple install disk with the disk utility on it.
What can I do to remedy this short of re-installing? Will a program like Disk Warrior or Tech Tool help?

Thank you. That's what I thought will need to happen.
One more question. I tried using the Apple install disk that came with the computer. It's an OS 10.5.6 disk. It does not see my 10.6.8 system internal hard drive to repair. All it see's is itself 10.5.6 disk. Do you think I can use a 10.8+ disk utillity since that is a higher system it will see the 10.6.8. Where the 10.5.6 does not?
I don't want to turn the computer off for fear I'll get the question mark again. P-Ram got me going last time but for how long I don't know? It would be nice to be able to turn the computer off for the night and startup as usual to give it a rest and try to reset itself.
Thanks for your help, I know I will eventually need to re-install. But I am in the middle of a project with tight deadlines and all I can do right now is back-up. Trying to migrate to another computer temporarily to finish the job. That's a lot of extra work in the short time also.
Just trying to put a band-aid on it for another couple weeks.

When I have video clips on my timeline, they do not play in the monitor screen. I hear the sound track but can not see the image. To test if my new files are somehow the problem, I went back and used video files that I used successfully a year ago, and th

When I have video clips on my timeline, they do not play in the monitor screen. I hear the sound track but can not see the image. To test if my new files are somehow the problem, I went back and used video files that I used successfully a year ago, and they no longer play in the monitor window. I hear the sound track, but do not see any video. Have I changed some setting that controls video playback in the monitor window?

Randy Ruttger
Thanks for the follow up.
Missing in this equation were the version of Premiere Elements that you were using and the computer operating system on which it was running. But...
The deed is done. But.....Until now and after you went ahead and moved to version 12, we now learn what version of Premiere Elements you were using. We still do not know the computer operating system involved.
You just said Premiere Elements 10. Premiere Elements 10 is hit by a serious known display issue if the computer uses a NVIDIA GeForce video card/graphics card. In this issue, the only remedy is to roll back the driver version to about May 2013. The description of the problem and how to do the roll back are described in one of the Announcements at the top of this forum. What video card/graphics card does your computer use?
On another front, Adobe will be releasing a new version of Premiere Elements any day now. No one but Adobe knows the feature set for the new version. That type of information is announced at the moment of release of the new version.
So the remedy to the problem that you presented in this thread could have been...
1. Rolling back the NVIDIA GeForce driver version to about May 2013 if possible (Windows 8 or 8.1 64 bit, may not be possible)
2. Move to another version of Premiere Elements (which you did)
I offer the above for consideration so that you can review your decisions. We are pleased to learn that Premiere Elements 12/12.1 works for you.
Please do not hesitate to ask questions and ask for clarifications, but remember that the answers are in the details.
Best wishes,
ATR

P55A-GD65 Can not see Sata III drive

Similar Messages

Maybe you are looking for