P67A-GD55 - Two beeps after turning on the reboots loop

Hi
just installed a P67A-GD55 with a i5 2500k into my PC and everything was working fine, all drivers installed etc booted to Windows 7 no probs. Restarted and went into BIOS to check a few things then rebooted.
PC starts, two beeps, then reboots, continuously.
No BIOS LED flashing. So it seems two beeps means parity error. I've looked this up and mentions something about first 64k of mem check failed. To check RAM.
So went through each slot with one RAM and tried different RAM too to make sure, no difference. So booted up with no RAM in. No beeps but PC just starts then reboots in a loop.
Never got anything on the screen.
Checked all connections, removed all hard drives etc no difference, unplugged USB cables etc so in end just had graphics card, one stick of RAM, CPU and power plugged in. Still two beeps.
Reset CMOS still same, two beeps the reboot loop.
Tried all sticks of RAM in another motherboard and i5 760 and boots fine so its not the RAM.
Can't understand it as it worked fine at one point.
Is my motherboard faulty ?

Quote from: Mark on 01-June-11, 17:15:51
MSI is right. In the UK you need to get the product replaced through the retailer. You might need to phone Aria in this case.
I've filed an RMA request at the moment and told them what yourselves have said. Just need to wait now.
Didn't want to ring them just yet as there RMA number charges you 60p per minute.
I'll just have to wait and see what happens.

Similar Messages

  • My bookmarks are lost after turning off the computer unexpectedly (power problem),how can it recovers?

    My bookmarks are lost after turning off the computer unexpectedly (power problem),how can it recovers？ Thanks a lot !!!!
    我的书签在电脑突然被断电之后全部丢失了，我该怎么办呢？？谢谢啦！！~~~~

    This can also be a problem with the file places.sqlite that stores the bookmarks and the history.
    * http://kb.mozillazine.org/Locked_or_damaged_places.sqlite
    * http://kb.mozillazine.org/Lost_bookmarks

  • HT5642 After turning off the notification switches of some apps in notificaton center, there are still notifications. I'm confused. Why?

    After turning off the notification switches of some apps in notificaton center, there are still notifications. I'm confused. Why?

    Just guessing, but I would think, as I look at mine, that it might have to do with when the apps were added to the device. To be honest, identifying this as a bug might not be correct. You are the first person I have seen post something like this, so it must not bother others. You can leave feedback for Apple on the feedback page. Go to http://www.apple.com/feedback and then click on the appropriate link.

  • My mac mini loses connection with my receiver after turning off the receiver then back on

    My Mac Mini loses connection with my Onkyo receiver NR-609 after turning off the receiver then back on.  The only way to reistablish the connection is to unplug then replug the HDMI cable to the Mac Mini.  There's no effect if I unplug then replug the HDMI to the receiver.  Any help or suggestions would be appreciated.  I've searched a lot but haven't found much of anything so if this is covered elsewhere I would greatly appreciate a link.
    Thanks in advance

    Hi and thanks.  I don't know about the audio prefs.  When it happens I am not able to see or hear anything from the computer until I un/re-plug the HDMI to the Mini.  I'm not sure it's changing to something else because there's nothing else connected for it to change to.  I could see that perhaps the audio will change to the Mac Mini's internal speaker. 
    I found out last night that if, after I lose the signal,  I use my ipad to play a video on the Mac Mini using the Remote app and home sharing the signal gets righted and I can see/hear the computer again.  It's quite an inconvenient fix though and I wish and hope someone here can help me.

  • All message gone after turn on the handphone and p...

    The day before yesterday, when i was listening to music using my N97 phone. It run out of
    battery and it automatically turned off. After i came home, i charge it using my power
    cable and turned it while it was charging. Then i leaved it alone until few hours later
    it was fully charged and i found a message received from my friend. When i opened it, i
    found all my messages are gone. including those in INBOX, OUTBOX and old messages in "My
    Folder". I also checked the phone memory and only 1K of data left as messages.
    How could that be happening?
    After that I tried to synchronize the messages back from my old phone, N73, since most of
    the old messages are transfered from it. I used the same way as I did last time when I
    transfered the messages, contacts and calendar entries, which is, go to N73 Menu -> Tools
    -> Transfer -> Phones -> My N97, Options -> Edit, choose Sync data as Text Messages. then
    back and Options -> Synchronise. After a while, it shows that 1000+ messages are
    retrieved to the N73 phone( which is weird because it should send the messages instead of
    retrieving). Then when i check out messages on both phone and found out that 2 messages
    are transfered to the N97 INBOX which are the last messages in the INBOX and 2 messages
    are transfered to the N97 Outbox which are the last messages in the OUTBOX too. But the
    rest are not transfered. Then I check out my N73. and found out that most of my messages
    are gone except less than 5 text message, few MMS and some Bluetooth files(which should
    not exist in the OUTBOX because I usually delete it after successful transfer the files)
    exist.
    This is also ridiculous because I did the same action for synchronizing phones before
    with exactly same setting and that one working fine. But this one most are missing. Even
    if I did some setting wrong, I should lose all the messages instead of most but few left.
    And most weird part is that some files that did not exist in my OUTBOX before exist in it
    now.
    Can anyone tell me how to recover those lost messages? Or give any explanation about
    this? THANKS!!!!

    OK, here are more specific instructions:
    1. Open Finder (double-click the Finder icon in the Dock).
    2. On the left side of the resulting Finder window click on Applications.
    3. Double-click on "Image Capture".
    4. Follow the instructions above.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Error in mat doc after turning in the production in MFBF

    can anybody please help me with this issue. After the user has turned in production (thru MFBF), the material doc is getting posted. that is fine. Also there is output tab on the material doc and when we see the output there is an error that says
    Language  is not allowed
    Message no. TD604
    Diagnosis
    You want to edit a text. However, the text language specified does not exist.
    System Response
    Editing is rejected.
    Procedure
    The valid language keys are listed in Table T002. Please check the entries in this table.
    becuase of this error the user is not able to print labels. why this error would be cominng? can anybody help? I also checked in table T002 and we see that there are all kinds of languages, what i do not understand is what language it is talking about and what can we do about this
    Thanks
    Anusha

    OK i have checked the condition records in the MN22 for all key combinations, there are no condition records. now this problem does not seem to happen all the time. For some materials, there is no problem, and after the production is turned in the mat doc gets posted fine and the label also gets printed fine. It is only for certain materials this eems to happen, are there any settings in production version or BOM that might be causing this?
    Thanks
    Anusha

  • HT5019 unable to get turn on display after turning on the power button ,no caps lock is turning on too,even a light at unlock button to open display is not going down , mine was a late 2008 mac book pro ( 17 inch ).please help me to solve my problem

    unable to get my screen on even after turning on power button .
    light at display unlock was not going down ,
    no caps lock button turning on .
    please help me to rectify my problem apple community

    unable to get my screen on even after turning on power button .
    light at display unlock was not going down ,
    no caps lock button turning on .
    please help me to rectify my problem apple community

  • HT2452 my computer is frozen. i did a restart and after turning on the computer froze again. i diconnected the computer, still the same. what else can i do?

    my desktop is frozen. i did restart, disconnect several time, after turning on, it is frozen again. what else can I do?

    Try resetting PRAM
    http://support.apple.com/kb/HT1379
    Try booting up in Safe Mode
    (Hold shift on power up until loading bar appears under Apple and wait.)

  • The Reboot loop and iOS version problem

    My iPod went into reboot loop,and I restored it.But I have iOS 6.0.1 now,not 6.Can you downgrade?

    All I can say in this Apple forum is that Apple does not suport downgrading the iOS.

  • Strange noise after turning off the notebook (dv6-6160ew)

    Hi I'v just got my new notebook dv6-6160ew and I am kinda worried about one thing, whenever i turn it off, about one second after it powers off i can hear a quite loud noise that saund as if a spinning disc was slowing down and stopping, im guessing that it is the hdd (as there is no cd incide the cd-drive) so I just want to know if this is normal as I have never experienced it with any other notebook and I've had quite a few (no hp though). I will be very gratefull for the answer.

    Hi Borg-Frog,
    Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I see that you are looking for a way to disable to the TouchPad. I will be happy to help you with that. I have included a document below that will show you how to do that under the Disabling the TouchPad section.
    Using and Troubleshooting the TouchPad Windows 8
    Thank you,
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • HP Officejet Pro 8600 N911g always cannot print and scan after turn on the Mac from sleep

    Dear Community:
    This is my printer:
     1. Product Name and Number
    Product Name HP Officejet Pro 8600 N911g Product Model Number CM750A Product Serial Number {Private Information Removed} Service ID 23022 Firmware Version CLP1CN1150CR Total Page Count 4187
     2. Operating System installed (if applicable) 
         Mac OS X 10.7.5
     3. Error message (if any) 
    After several issue which prevented me from printing I uninstalled all HP software on my Mac OS X 10.7.5 laptop. I downloaded and installed: Officejet-Pro-8600_v12.23.0.dmg after complete I can print and scan. then I go home and put my laptop to sleep. after I come back to work this morning I cannot print and scan again. HP utility cannot connect to that printer because all information there (all fields) displayed as: unknown Please help.
    4. Any changes made to your system before the issue occurred
         Nothing. I just put my Mac to sleep and put it back on.
     5. In the subject title, include a brief, specific description of the problem, and your product information (i.e., product name of your laptop, notebook, printer, other device, etc.)
    After several issue which prevented me from printing I uninstalled all HP software on my Mac OS X 10.7.5 laptop. I downloaded and installed: Officejet-Pro-8600_v12.23.0.dmg after complete I can print and scan. then I go home and put my laptop to sleep. after I come back to work this morning I cannot print and scan again. HP utility cannot connect to that printer because all information there (all fields) displayed as: unknown Please help.
    Is there anyone out there who have any idea on how to solve this problem? Thank you all in advance.
    This question was solved.
    View Solution.

    OK, here are more specific instructions:
    1. Open Finder (double-click the Finder icon in the Dock).
    2. On the left side of the resulting Finder window click on Applications.
    3. Double-click on "Image Capture".
    4. Follow the instructions above.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • 2 issues concerning early 2011 mbp:screen no reaction after turn on the lid and airport

    the first issue is more serious.Ive read other posts related to this and still cannot figure it out.I dont why the screen wont turn on as i open the lid-the black screen.I turbulently press the keyboard and still no reaction.what i do is to mandatory press the turn-on button and make it shut down,restart it following.and im sure the battery doesnt run out.moreover.my college's wireless is wpa2 authentication.as long as i close the lid and reopen it,the airport requires the password.the PROBLEM is i enter the correct one but i dont have access to network.i have to "disconnect" it and reconnect,thus render me make the network available.you see the main reason is the lid.literally as i close the lid,something goes wrong...
    any ideas would be appreciated.thx

    SOLUTION!!! from an AppleCare advisor and it worked!!!!
    MBP SMC reset
    Shut Down Computer
    Shift
    Control
    Option
    Power Button
    Hold all and count to 10, then release
    and power on

  • My iPad 2 won't connect to wi-fi even after turning off the device. Help?!

    Someone help. My wifi works at home but it doesn't seem to connect here at my parents house? Why

    I have the same problem but with my Ipod touch

  • Boycott upgrading your phone due to the Reboot Loop!

    HTC Incredible users please boycott upgrading your phone because of this patch/crash release.  It was done intentional and its working as designed.  Most of you are taking the bait and upgrading.  HTC & Verizon hate this phone and want as many users off of it as possible.  Think about it...the phone was no longer being sold almost 2 years ago...um everyone one's contract is close to an upgrade if not already.  HTC has had nothing but problems with this phone.  When the company release a patch for this phone it introduces another issue. No revenue comes from this phone anymore.  I myself only had one issue with the phone prior and that was the Galley not showing my pics/vids.  I had to power cycle the phone.  Other then that I love my phone...the provider and manufacture pushed me away.
    I have been in contact with others who are starting a class action law suit.   Verizon and HTC messed up and we should have to pay.  It's more like they need to pay.  Oh yeah, I lost my new borns pics/vids over this stunt so I'm ****** and going after them...please join in!

    I agree with you 100%... words cannot even explain how angry this makes me, and how wrong this is on so many levels.  Coincidence that this starts getting pushed out around the time Verizon does away with their unlimited plans??? NOT.  I'm with you on this Boycott idea.  Verizon seriously needs a swift kick in the face for the way they treat their customers.  Hmmm let's see - they did away with the VIP discount, they did away with the discount if you renewed your phone online instead of in person or on the phone, they did away with their unlimited plans... bottom line, they did away with any sense of loyalty entirely.  I've been with Verizon 10 years, and this is the thanks I get?  Our entire company uses Verizon... hmmm as the IT Director, I may have to pursuade them to use another carrier... 
    Disgusting....
    Anyway - from waht I hear it says in the Verizon contracts that you cannot file a class action lawsuit against Verizon, but I hope I heard wrong.  If you do make any headway with that I would certainly appreciate you sharing the information because I am so in on that.

  • After creating two mac users do not see when I turn on the second

    Hello , after installing Yosemite I created two administrative users , turn on the computer but I do not see you and the other , I have to get into the first and by this move to the second . how do I fix ? thank you very much

    Hi jpacchioni,
    I apologize, I'm a bit unclear on the exact issue you are describing. If you are saying that you are not seeing a login screen or the second user on startup, thereby forcing you to go into the first user and then switch to the second user, you may need to check your Login Options. You may find the following articles helpful:
    Customize the login experience
    If you are an administrator, you can specify how the login window looks to all the other users.
    Choose Apple menu > System Preferences, then click Users & Groups.
    Click the lock icon  to unlock it, then enter an administrator name and password. 
    In Users & Groups preferences, click Login Options.
    Click the “Automatic login” pop-up menu, then choose a user, or choose Off.
    If you choose a user, then whenever the Mac starts up, that user is automatically logged in. If you choose Off, then at startup the Mac opens a login window showing all the users. Automatic login takes effect the next time you restart the Mac. For better security, don’t set your Mac to automatically log in an administrator. If FileVault is turned on, automatic login is disabled. 
    Select the options you want. If you have any questions, click the Help button for detailed information.
    OS X Yosemite: Set up users on your Mac
    OS X Yosemite: Login Options pane of Users & Groups preferences
    Regards,
    - Brenden

Maybe you are looking for