P67A GD65 (B3) - Boot Up Problem

Every time I cold boot, I get the initial beeps, then it hangs on a black screen, with 98 in the bottom right hand corner. I have to turn the computer on and off another one to five times, before it boots up normally.
I have updated to the latest bios, disconnected every USB device, but the problem still occurs and once in Windows, I get no BSOD's whatsoever, so I'm running out of ideas.
Any ideas, before I go to Tech Support?
Thanks,
Kev

Quote from: HU16E on 19-November-11, 17:50:16
Yes. Please try it without a HDD connected. If it completes POST quickly, then it is either that one single HDD that was connected, or the Intel or Marvell controllers are most likely faulty. That would mean RMA of the mainboard for sure.
Edit: Rather than RMA, if a bad controller could be identified, Intel SATA II or III, or the Marvell SATA III, the good controlled ports could still be used. Would limit the connectivety choices though.
I tried it with no HDD's connected, no joy mate.
I've also just installed another PSU and the problem is still there, so I'm giving up and sending it back.
Cheers for your help mate, but I've given this problem a LOT of time and money and enough is enough.

Similar Messages

MSI P67A-GD65 infinite boot/loop problem

installed everything into my case and go to boot into the UEFI and nothing !
i press the power switch, everything starts fine and the fans spin up and the LED's on the board are fine, waits 5 secs then it shuts itself off and tries the exact same process again. it keeps doing this until i cut the power !
i've checked the 24pin etc, KB & mouse r fine, 2 different sets off RAM in every slot, cleared CMOS (i think).
seems like a very common problem with this board after a bit of googling !!
also tried
Quote
this is the 1st time ive used it !
tried the OC genie button on and off.
been sitting in the box unused for about 1.5 months. doubt that means anything tho.
put the stock cooler on securely, and still the same problem !
now tho, it wont start for about 3 secs after i press the power button
and
Quote
disconnected all the SATA's bar 1, and still the problem :/!
all the standoffs etc r fitted correctly and iv re-connected the 8 pin cpu and 24 pin. 1 stick off RAM in the 1st slot also :/!
checked no molex connectors r touching the case metal either
any suggestions?

motherboard: MSI P67A-GD65 (B3) bought on march 31st and used today for 1st time
CPU: intel core i7 2600K
CPU Cooler: tried an alpenfohn matterhorn with Scythe 1850RPM gentle typhoon Push/pull also tried the stock cooler
RAM Corsair CMD4GX3M2A1600C9 (2X2GB kit of 1600Mhz CL9 corsair dominator DDR3) and tried Patriot PSD34G1600KH (2X2GB kit of Patriot signature DDR3)
PSU Corsair TX650 650w psu
GPU XFX radeon 4870 1GB
Case NZXT M59 + mainly scythe fans and a noctua and coolermaster
DVDRW liteon DVDRW
Storage 128GB kinsgton SSDnow V100, 1TB Samsung F3 7200RPM, 1TB Hitachi 7K100 7200RPM all sata 3gb/s
Generic 5.25" fan controller
2 x 12" blue CCFL's
OS windows 7 x64 professional (installed on the SSD, but havent booted it yet as the board doesnt even get to BIOS :()
peripherals Microsoft reclusa keyboard and gigabyte GM-6990 (i think) mouse
monitor Benq g2222hdl connected via DVI
the only things i have changed today are, put the new notcua fan in my case, changed the Motherboard and CPU from and Asus M4A78LT-M & Athlon II X4 640 to MSI P67A-GD65 (b3) & intel core i7 2600k. Also, put the alpenfohn matterhorn on today.
everything is confirmed working apart from the CPU & Motherboard. everything worked yesterday, but i didnt have the necessary equipment to test the motherboard or cpu before using them together (today)
hope this will help

P67a-GD65 (b3) boot problem (reboot and select proper boot device)

Hello All,
I have the following problem;
When I start my computer sometimes it starts normal or I get the following warning;
Reboot and select proper boot device.
If this happens, its stays for a few seconds on A2 at the lower right corner , then MSI mainboard screen, and then the above warning.
When i use the reset button, it starts normal or same problem.Sometimes i need to restart it like 5-7 times to get it started normal.
My system info:
Mainboard: MSI P67A-GD65 (MS-7681)
Chipset: Intel Sandy Bridge
Processor: Intel Core i7 2600K @ 3400MHz
Physical Memory: 4096MB (2 x 2048 DDR3-SDRAM)
Video Card: AMD Radeon HD 6900 Series
Hard Disk: Seagate ST31000528AS ATA Device (1000GB)
Hard Disk: Seagate ST3200822AS ATA Device (200GB)
Hard Disk: Seagate ST3200822AS ATA Device (200GB)
DVD-Rom Drive: XMTQ FGPIR0DURGHI
DVD-Rom Drive: Toshiba Samsung SH-S223C CDDVDW
Monitor Type: LG L1915S - 19 inches
Monitor Type: ACER X233H - 23 inches
Network Card: Microsoft Virtual WiFi Miniport Adapter
Network Card: Wireless-N 300 USB Adapter WNA3100
Operating System: Windows 7 Ultimate Professional, Media Center 6.01.7600 (64 bit)
DirectX: Version 11.00
Windows Performance Index: 5.9 on 7.9
Mainboard bios: 1.9
Hopefully someone can help me.
Thanks,
Tammo

Zalman ZM660-XT
AC Input Range Voltage 100VAC ~ 240VAC ±10% DC Output
Frequency 50Hz~60Hz Output V. Output Load Rating Combined
Power
AC Input Current
(Rated) 115VAC 9.5A Imin Imax Ipeak
230VAC 4A +3.3V 0.8A 30A 35A 155W 660W
PFC Type Active PFC +5V 0.5A 30A 35A
Power Factor 99% Maximum
+12V1 0.5A 20A 22A 636W
Inrush Current Limit
(@ Cold start at 25°C) 115VAC 80A +12V2 0.5A 20A 22A
230VAC 60A +12V3 0.5A 20A 22A
Efficiency 88% Maximum @230VAC, Typical load +12V4 0.5A 20A 22A
DC Output
Voltage
Regulations Output V. Regulation Range At Full
Load -12V 0.0A 0.8A 22.1W
+3.3VDC ±5% +3.14V~+3.47V +5VSB 0.1A 2.5A 3.5A
+5VDC ±5% +4.75V~+5.25V Protection Features
+12V1DC ±5% +11.4V~+12.6V Over Voltage Protection(OVP)
+12V2DC ±5% +11.4V~+12.6V Over Current Protection(OCP)
+12V3DC ±5% +11.4V~+12.6V Short Circuit Protection(SCP)
+12V4DC ±5% +11.4V~+12.6V Over Temperature Protection(OTP)
-12VDC ±10% -10.8V~-13.0V Under Voltage Protection(UVP)
+5VSB ±5% +4.75V~+5.25V Ambient Temperature
DC Output
Ripple
& Noise Output V. Specification At Full
Load Operation 0°C ~ +40°C
+3.3VDC 50mV Storage -20°C ~ +80°C
+5VDC 50mV Ambient Humidity
+12V1&2DC 120mV Operation 5%RH ~ 95%RH
+12V3&4DC 120mV Storage 5%RH ~ 95%RH
-12VDC 120mV Dimensions
+5VSB 50mV 180(L) x 150(W) x 86(H) mm

P67A-GD65 (B3 )boot problems

I've built my box around mid-December (2011) and ever since, I've experienced the same issue as well.
The very first time it happened, I ran the repair tool, but just like others said, it could not repair it. I DID NOT have have MSI control center installed for the first few weeks and yet the random reboots at the windows logo still happened, so I'm certain it is NOT an MSI control center issue (at least in general).
Yes, it is very hard to pinpoint, just like others said. Most of the time it boots just fine. On those rare occasions (maybe once every 20-40 boots) I just let it reboot automatically and then it's all fine.
I'm NOT an overclocker at all, so I have everything set as it is out of the box and aside from this random, occasional reboot everything works fine.
I don't remember which bios version originally I had, either 1.C/D/E, but I upgraded to 1.G and it still does it, and did before the bios upgrade. Currently 1.E is the latest which I don't have.
MSI P67A-GD65 (B3)
Intel i7-2600K Sandy B
G.SKILL Ripjaws Series 16GB (4 x 4GB) F3-10666CL9Q-16GBRL
ADATA S510 Series AS510S3-120GM-C SSD
Nvidia GeForce GTX 275
Win 7 x64 Ultimate

Ok, so I just want to recap on this issue. It seems my machine is stable now.
I have reinstalled windows about 4-5 times this week, trying to test what the problem might be. Wasn't sure if it's a driver, the service pack (1) or maybe the order of installation messed something up. So I wanted to start clean the various installations/testing. None helped.
So I noticed there was a new BIOS update available with v 1.I (dated 01/12/2012). As a side note, I don't understand why they post version numbers with letters (A, B, C, D, etc) but in the BIOS or in other programs, such as CPU-Z, they report the version number with numbers. Anyhow.
So I installed this BIOS. That didn't solve it either. But while I was running the OS, I noticed my BIOS LED is flashing, so my primary BIOS failed. It still booted and ran fine. I just didn't understand why did the primary BIOS failed since the BIOS update tool (downloaded from this forum, reported the flash was successful.)
I cleared the CMOS, reset the BIOS to default values, installed windows 7 ultimate x64 using AHCI and IDE mode. None made any difference. Still experienced random reboots at the Starting Windows screen (but it rebooted only once - consequent reboots were fine).
So I used the dual BIOS to re-flash the primary with the secondary. The secondary had BIOS v 1.11 (dated 04/20/2011). So now I'm running this version. Lo and behold (and also knock on wood) I don't have any random reboots so far. That's about 5 days now.
So I want to close this thread by saying, that it seems there was some issue with the new BIOS releases (I only used 1.G and 1.I) but reverting to the original one (which is in the secondary BIOS - 1.11) makes my machine ran stable without random reboots - so far.
I think this is how I'm going to leave it. This works. As they say, if it ain't broken don't fix it, so this is the BIOS version I'll stick with.
Long live the King!

MSI P67A-GD65 Slow Boot

At times I'll get stuck at B4 or 98 error code for a good 5-15mins plus. I will either have to wait it out or press reset until it boot properly. Even when it gets passed this issue I still have to wait a while looking at the windows start up animation. I'm using a 2500k right now, my i920 system only displays the animation once before proceeding into windows.
The major issue is the B4/98 issue. I have tried a lot of things to no availability. If all else fails I will send this board back to Amazon and pick up an Asus or w/e.
Thanks,
MSI P67A-GD65
2500K
ASUS 550 ti
8gb corsair vengance
crucial m4 64gb 0009
corsair hx520
usb card header card reader
sony dvd/rw sata
windows 7 pro 64

Quote
At times I'll get stuck at B4 or 98 error code for a good 5-15mins plus.
Quote
Is the B4 error just a generic
http://www.xannex.co.kr/doc/ami_aptio_4.x_status_codes_pub.pdf
98 = Console input devices connect
B4 = USB hot plug
What other USB devices besides the "usb card header card reader" and the mentioned mouse/keyboard combination do you have connected to your system?
Can you please try without the card reader?
Quote
It's a B3 with the latest bios.
The latest Final UEFI/BIOS Release (E7681IMS.1E0) or the latest BETA Release (E7681IMS.1F5)?

P67A-GD65 RAID set-up problem... HELP!

First off I tried the search to find any threads but the search didn't come back with anything relevant.
So here is my problem. Brand new build and can't get the RAID drivers to install. Can't even find the drivers by themselves without a EXE file to run them. I have them on a USB flash drive but Win7 won't recognize them because they are still bundled into the EXE program. I've tried to extract them from the Marvell RAID Drivers given on the MSI support site but still no luck. I have the MSI P67A-GD65 with two Seagate ST32000641AS Barracuda XT HDs plugged into the Marvell SATA III ports 7 & 8. Win7 install sees them as two separate drives so I'm stuck trying to find some drivers that Win7 will recognize and install off the USB drive.
Also I'm reading that the Marvell SATA III controller isn't as fast as the Intel P67 SATA III controller.... should I swap the cables over and avoid the Marvell? If so any help finding the Intel P67 RAID Drivers would be greatly appreciated.

Things have changed since my last build, thank God!
In the old days you had to install the RAID drivers before installing the OS onto the array. Today I just set up the RAID 0 array after installing Windows 7 onto one of the two drives. So all that time I spent looking for drivers that weren't part of an EXE file was a waste. I did swap from the SATA III Marvell ports (7 & 8) to the SATA III ports (1 & 2) that are Intel P67 PCH. I then installed Windows 7, popped in the MSI motherboard disc, and loaded the Intel RAID drivers. After that I opened the Intel Control Panel that was installed with the RAID drivers and set-up the RAID 0 array. Now it seems Windows 7 is migrating itself onto that array. Bad news... because the array is so large. Two 2TB drives... its going to take a long time. Not sure if there is a better/faster way.

X79A-GD65 (8D) booting 32GB problem

Hello guys i just buyed few days ago a new rig:
Intel i7 3930K socket 2011 six core C2 3.2 ghz
X79A-GD65 (8D) rev 1.1
Bios 1.7 upgraded from came with 1.4
32GB DDR3 G.Skill RipjawS Z 8x4GB FS-12800CL9Q2-32GBZL 1600mhz CL 9-9-9-24 1.5v
The problem is I cannot boot at all with all ram slots active although it says on msi site its compatible with this ram. What am I doing wrong here?
Please help thx in advance.

Quote
There are a good number of reasons the last dimm slot is not working. #1, there is a short or ground underneath the mainboard. Often caused by a standoff out of place. #2, you have a pin in the CPU socket that is bent. #3, CPU cooler is not mounted evenly. #4, faulty dimm slot, there is a problem with the dimm contacts in the slot, piece of foreign material or a contact finger damaged.
Good catch, I was only responding to the immediate question of how to increase dram v.
Quote
I put first one ddr3 into dimm1 then boot
then into dimm3 then boot
then into dimm5 then boot
then into dimm7 then boot
after that dimm2 then boot
then after dimm4 then boot
then after dimm6 then boot
and last dimm8 no boot

MSI P67A GD65 Multiplier and software problems

Hi
i just bought i5 2500k and Msi mb, it came with 1.4 bios version and the maximum multiplier that i could log into Windows was 44 even though the vcore adjustment didnt work properly
maxing out at 1.224 (bios reading) no matter the voltage set manually, I updated to 1.7B4 and i was able to get into windows at 46x100 the downside of the new bios was the memory suddenly stopped working at 2133 10-11-11-30 1.65v even 12-12-12-30 would end up in oc failed message so i had to settle for 1866. Now i updated to 1.8B5 and i can run my memory at 10-11-11-30 again no problem but
maximum muliplier went down to 44... again - theres no way to make system work with 45 or higher multiplier so basically oc-wise 1.8B5 is like 1.4 with vcore adjustment working properly/pll fix - Plz p67 users need proper bios.
Second problem is that Overcloking center crashes with 0xc0000005 code right after launching exe - first happened on my old XP SP3 so i installed fresh Win7 unfortunatelly its the same story.

Ok now im mad i flashed back to 1.7B4 and guess what i cant choose any multiplier above 44! Whats weird is that although bios version says 1.7B4 its behaving exactly like 1.8B5
Every time i changed some voltage option in bios V1.4 or V.1.7B4 the pc would power down and then power up, since 1.8B5 it would just reset. That and inability to go above x44 when just yesterday
i could go x46 (i didnt check more as i want to run my SB below 1.35vcore) makes me think my cpu is artificially locked and ability to go above x44 in 1.7B4 was just an accident that was
corrected in 1.8B5 whch has some code inside that prevents (in case somebody wants to downgrade) to update data responsible for cpu oc. Another example supporting that is that my cpu can
boot up at 4.4 ghz@stock voltage (1.168 in bios) log into windows and run some tests , of course it would freeze and reset randomly after some seconds or minutes but still... On the other hand changing the mulitplier to 45 and vcore up to 1.4v doesnt even make HDD start spinning and load WIndows after the MSI logo screen vanishes, its just seems locked.

P67A-GD65 B3 boot priority keeps changing with USB device plugged in

I just bought this board this week and updated to the latest ( 1.D0 ) bios and still having these issues. First issue is that when in bios, my mouse only moves up and down. Can't move it sideways. I have to use my keyboard to adjust settings. I have Logitech USB keyboard and mouse. Second major issue is that I have 4 drives in a Raid setup and 1 1tb drive for storage. The Raid drives are hooked up to the Intel controller and the 1tb drive is hooked up to the Marvel controller. Everytime I turn the pc on and off or do a reboot the bios keeps changing the hard drive priorities to having the 1tb drive 1st even though I had the Raid drive as being first. One thing I notice is that if I unplug my USB card reader it boots fine and doesn't change the drive priority. It would be a hassle if I have to unplug my card reader each time and plug it in when I use. Kinda defeats the purpose of a front panel card reader. BTw the reason I had to plug my front panel card reader into a passthrough USB is because the board only had one 2.0 USB header and that was already being used by my 2 front panel USB connectors which was also disappointing.

Ok, all testing complete. Installed a USB 3.0 external, & a WD 2TB HDD to the Marvell. Settings, Intel AHCI, Hot Plug enabled. All USB functions enabled. Marvell set for AHCI. Booted to Windows normally. Marvell HDD showed up at POST, but in Windows had to be activated & assigned a drive letter. Full shutdown. At fresh startup, all was normal in the boot sequence with the Intel OS HDD as the #1 Boot Option, & the Marvell HDD was listed in the BBS as available to assign it's boot order. Continued to Windows & did another full shutdown. This time on a fresh restart, the Boot Option Priority was still #1 the OS HDD, but, the BBS boot order was the Marvell HDD listed as first & the Intel OS HDD as the #2. This didn't really cause any problem to boot normally even though the HDD BBS sequence was out of order. Full shutdown. At this restart, the Marvell 'was' #1 in the Boot Option Priority & the Intel OS HDD didn't show in the BBS list. I went ahead & let it boot into Windows which it did without a hitch & then I shutdown right away. At this point I took the USB external out of the picture, & it had no affect one way or another as to the boot order. Full shutdown/fresh startup, but this time, set Marvell to IDE, changed Intel Hot Plug to all disabled, save & exit, next cycle, Marvell was #1 Boot Option Priority again. Set the Intel as #1 Boot Option Priority & also as #1 in the BBS, & at every shutdown & restart since, the Intel OS HDD has held as #1. I went back & changed the Marvell back to AHCI later, & it still held correctly as to what I had set in each fresh startups.
Summary? I believe the Marvell devices are being initiated first in the POST sequence. Disable of Hot Plug seemed to help. Since the Marvell has no way to disable Hot Plug, the HDD always shows up in the Sys Tray. My advice? Unless you have multiple ODD's, I would suggest to disable & not use the Marvell ports or controller at all, or use it for ODD's only. How your card reader fits in to all this, I have no way to test for that. Place the storage HDD in one of the Intel SATA III ports, leave the 4 HDD's in Raid in the 4 black SATA II ports, place the ODD if only one in the other Intel SATA III port. Bottom line; MSI Tech Support needs to be notified & involved with this. By your description, there is an obvious conflict with the card reader & how all the boot order is established. Although I did have the Marvell take over the boot order a couple of times, it never caused the OS to not load as normal or cause any problems while in Windows. http://support.msi.com/

P67a-GD65 wont boot up.

Hello
My brothers computer now refuses to boot. I have tried clearing the CMOS but to no avail.
The fans spin up on the CPU fan and the graphics card but I get no video.
The last thing he did before it stopped working is reduce the CPU voltage to 1.20v to lower the temperature of the processor which at 65C under load.
The processor was running at 4.3GHz.
Any further instructions would be greatly appreciated.
Is there a way the BIOS can be flashed without the machine booting up
Cheers
Ed

Quote from: HU16E on 17-February-11, 03:20:04
As long as the temp stays below 72.6C at full load, everything should be fine. Since you are OC'ing, lowering the CPU V. down to 1.200v's, appears to be too low.
I agree
Yeah it had been running fine at about 1.22v but he decided to try and "fine tune" it to get the temps even lower. Now it looks like either the motherboard or the processor is dead.
Regards
Ed

Help with P67A-GD65

Hi everyone, just wanted some advise please, i have ordered the parts for my new gaming pc (This is my first build)
I have ordered the MSI P67A-GD65 motherboard and after doing some research i getting worried that my CPU cooler won't clear my ram.
I have the coolermaster V6GT CPU cooler and the G.Skill RipJawX 4GB DDR3 kit
I just wanted to know if anyone else has this board RAM and cooler ?
If not could i get some advise on wether i should change my CPU cooler to some thing like the Akasa AK-CCX-4002HP Venom CPU Cooler ?
Or could i move my RAM into slots 2 and 4 ? would this work or would the system not boot properly ? (sorry first build )
Thanks to anyone that helps

Quote from: HU16E on 28-January-11, 06:46:30
Well, that's what I get for not doing the testing myself! The P67A-GD65 'does' boot with a stick in the dimm 2 black slot, & then with a second stick placed in the other black slot. However, the manual is specific about initial startup with a RAM stick in dimm 1, which is of course the first blue slot next to the CPU. Without starting from scratch again, I can't verify initial build startup with a stick in the dimm 2 black slot will work or not. I guess if someone tries it, & it fails, obvious move would be to go to the dimm 1 & give it a go. Trouble is, I can't go back & edit my posts now to correct them.
Ha, it's OK, I read the same thing in the manual. The manual certainly doesn't leave any room for assumption, it flat out states you should use 1 & 3.

P67A-gd65 boot problem after BIOS update

I'm not optimistic about this, but...
My P67A-GD65 was delivered with BIOS 1.5. (However, the stickers on both chips read 1.4.) I updated the BIOS to 1.7 using a DOS formatted USB flash drive. (The EM was updated as well.) Things seemed to be running OK.
I foolishly experimented with the 1.8A beta BIOS. I flashed from DOS again. After rebooting, I went into the settings to reconfigure the machine as it had been. The EFI screen hung, so I powered the machine down (from the button, not the PSU).
I've been unable to boot since. No display appears on the monitor. If it is powered down, the power comes back on for an instant, goes off again, and comes up again with nothing on the display. The USB keyboard and mouse never become active, as far as I can tell. I tried a PS/2 keyboard; no difference.
If this board has dual BIOS indicator LEDs, neither illuminates, which indicates that all is serene.
I have cleared the CMOS several times, using the jumper or the button at the rear I/O panel.
Any advice? Is there any way to force the use of the second BIOS? (I've read the MSI dual BIOS FAQ posted elsewhere, but didn't spot anything of use.)
RMA time?

Quote from: ScunnyUK on 01-February-11, 16:08:59
Hi,
The blue screens started after a clean Bios flash to the 18b10 bios then eventually it stopped working complety (just doing the start up cycle over and over)
I had tried reseting cmos and it doesnt make a difference, the motherboard will not post , boot , start up at all so default settings cant be set (although reseting cmos would set to default anyway)
Each time the board goes through the start up cycle (i.e. upon pressing start button the board will start up with fans spinning for a second then shut down, start up again with fans spinning for a second then shut down, continuasly repeating until main power is removed) I have used a multimeter to measure the voltage read points on the board and they show that there is no vcore being suplied to the cpu but all other points show the voltage is being supplied to those componants, so imo that is where the problem lies and I would sugest that the other ppl who are having this issue to also try measuring the voltage read points and see if the same thing is happening on thier boards .
If others are getting the same results (no vcore) then the msi techs should be informed of this issue..(imo)
1.8b10 still is a beta bios. I got random bluescreens with that one also at some point a blinking bios led. So I flashed back from secondary bios (using the first option (change disable in enable)in "security" in the EFI shell to allow flashing from secondary bios), blinking bios led now stopped, Then I flashed with 1.7, no issues sofar cpu now running stable at 4.5Ghz (already 2 days).

Problem with downgrading bios. MSI P67A-GD65 (B3).

Hi!
I'm having problems with downgrading my bios from version 4.3 to 1.19. I want to downgrade, because 4.3 doesn't want to boot when I use xmp settings for my RAM ( that might be related to my CPU since I have i5 2500k which is 32nm and 4.3 version of BIOS is recommended for 22nm processors ). When I try to flash with the MSI Forum HQ USB Flashing Tool I'm getting an error: "Rom file ROMID is not compatible with existing BIOS ROMID". I've ran out of ideas how to downgrade my bios so I'm asking you for help. My specs:
MOBO: MSI P67A-GD65 (B3)
CPU: INTEL CORE i5 2500K
RAM: G.SKILL RIPJAWS X 4GB (2x2GB) DDR3 1600MHZ CL6 (F3-12800CL6D-4GBXH)

Here you go. GD65 and GD55 usde the same BIOS files;
https://forum-en.msi.com/index.php?topic=179837.msg1295420#msg1295420

HELP! My 2011 MSI P67A-GD65 (B3) build suddenly refuses to boot

Hello, I am new to this forum because I hadn't had any troubles yet.
I built my system in July/August 2011. Here's what it has:
MSI P67A-GD65 (B3)
Intel Core i7-2600K Sandy Bridge CPU
16GB Corsair Vengeance 240-pin DDR3 1600
650w Corsair Enthusiast PSU
MSI N460GTX Cyclone 1GD5/OC GeForce Graphics Card
1x 2TB Hitachi 7K3000 7200RPM SATA 6 GB/s (With Windows 7 64-bit installed)
2x 3TB Seagate 7200RPM SATA 6 GB/s (For storage)
I have used this computer for graphics and video editing...it has served me faithfully. Yesterday evening while editing a Word document, I got "do you want to save your changes before exiting?" and of course I said yes. Then to my surprise my computer proceeded to shut down and reboot. At first I thought maybe I missed a Windows Update message telling me it would reboot in xxx minutes so I was not alarmed. But then as I watched it reboot, it gave me the POST message that there was no disc drive recognized. I thought that was weird since I never noticed it before. But then after the BIOS screen with the MSI graphics thing I was faced with a blank screen except for a flashing cursor two inches from the top of the screen. When I realized that this wasn't going to leave, I got a bit worried so I did a reset through my tower's button and same thing happened...I unplugged everything and let it sit for a few minutes... restarted 10 minutes later....same thing. Did it again and then went into my BIOS to look around. It showed no HDD's connected and I had 3 hooked up. I was concerned my HDD went bad so I connected it to another pc and accessed it with no trouble as another storage...I was happy my files are all there. So then I reconnected to my original build and got the same POST message, but this time the drives were visible in BIOS....but still no boot.
I have another blank SATA HDD so I removed all my HDD's and connected it by itself along with my SATA DVD drive and I tried to do a clean Win7 install on it. But at the point in the install process where it asks WHERE you want to install Windows, no drives showed up. So that door was closed. I tried the same thing again after swapping SATA port locations, thinking 1 was defective, but I got the same treatment from all of them...nothing recognized during the install process, although the drives are showing up in BIOS....
I think I know why the POST message is saying 'no drives detected,' though...I read it is saying that based on the SATA ports being used...I have 8 SATA's on my MOBO...4 6gb/s; 4 3gb/s. 7-8 are 6gb/s and ONLY when I have a HDD plugged into one of them does it show on the POST screen...which I still think is weird, and seems to have just started happening last night with the rest of the problems...but I could live with that since I could disable the message in BIOS I think.
But I have tried to clear the CMOS...all three ways...jumper, button, battery. I reset BIOS thru BIOS.... Nothing changes. BTW, in BIOS I ran a RAM memory check and it passed. Besides, I am not hearing any weird beeps...related to that....
I don't know why this would happen after working perfectly for 2 years... And why would it politely shut down in the beginning of the process anyways? I mean...I appreciated being asked to save my changes...but I don't know what else to do...PLEASE OFFER SUGGESTIONS...any help is appreciated.
Thank you in advance...I hope someone can help me! I am still covered by warranty...but I want to do this right.
Thanks!
Marie
EDIT: BTW, I have also tried unplugging everything from the pc except for the DVI and power plug in case that was interferring....

Quote
On a slightly different topic...would it work (I have never done this!) to take my OS HDD and boot it on another PC? I am thinking this would not work because of system files and etc., but I have always wondered this and now would be the best time for me to know
It mostly works if the components used aren't too special. As you have no RAID setup it should work. However you will need to reactivate Windows once it made it. Of course you will also need all drivers for the new machine. Be aware that you might not be able to connect to the internet before you installed the proper driver for the ethernet adapter.

P67A-GD65 (B3 ) & Windows 7 64Bit Boot Issue

Hi,
I feel the need to revisit this old forum post as I do not believe it has been fully resolved:
https://forum-en.msi.com/index.php?topic=156082.0
In summary the issue is "Most times the machine boots and performs flawlessly for hours, but often it boots with the Windows-7 “need to repair” screen and after running repair for a while Windows says: “Windows cannot repair the problem”…….but when I press the Reset button, the PC boots and runs just fine".
I only had the problem since updating from 1F beta 2 to the latest BIOS version. On the original forum thread there are some that had the view that the issue was introduced around BIOS version 1.F (full release, non-beta) and 1.G. Just to confirm this issue NEVER happened for me on 1F beta 2 or earlier BIOS releases. The original forum also has some people saying the issue did not exist on earlier BIOS versions as well.
Most people seem to have solved the issue by either resetting the CMOS or loading default BIOS settings. I tried this and it did initially solve the problem for me.
BUT when I installed new drivers (such as nvidia v301.24) or added new hardware (e.g. Bigfoot PCIe network gaming card) the problem came back.
This implies to me that there is an issue with the BIOS and that resetting the CMOS is a workaround rather than a true fix.
This leaves me with two choices:
- use an older BIOS, which is ok but limits me from the new functionality in the BIOS (including not being able to use certain hardware that the BIOS updates support)
- resetting the CMOS after loading new drivers or installing new hardware and then configure my settings (which is very tedious)
Neither option is ideal to me.
The main purpose of raising this issue is to ask whether MSI Support know of this issue and have it on their bug list to fix?
I am concerned it is not being addressed as other forum entries talk about BIOS version 1.K3 being the last version.
My system details are P67-GD65(B3), Windows 7 64bit, 16GB Gskill 2133Mhz memory, 2 SSD, 2HDD, Nvidia 570 GTX, Bigfoot network gaming card.

Quote from: momosala on 25-September-12, 22:19:54
Thank you _MELK_ for bringing us your experience.
It was already reported that this bug did not appear with older firmware versions.
It is interesting to know that version 1.14 does not have this bug.
This information should help the MSI support team to create a 1.K reliable firmware.
In my opinion, I do not think that Intel RST is the cause of this bug.
Sure thing momosala..
An update to this issue is as follow...
BIOS 1.14 fixed this issue completely. NO errors since I flashed back to it. I also reinstalled Intel RST without any issue either.
Note that I wanted 1.19 for another reason as well (fix for USB 3.0 port issues). I wound up flashing the chipset for the USB ports themselves instead . Now the MB works as intended! :D
WARNING: use the info below with CAUTION (not simple to do, and not provided/supported by MSI afaik)
INFO on USB 3.0 firmware/drivers -- again, use CAUTION and do your research before proceeding!
Note that it took me a few hours to complete the flash since I had to research which version of the chipset I had (hardware ID helped, LOTS of reading on the subject as well to find out HOW to flash my board properly).
You can find the drivers/firmware for the "Renesa USB 3.0 Host controller" by searching google for
Driver: Renesas/Nec Usb 3.0 Version 3.0.23.0/2.1.39.0 WHQL.
I used the 2.1.39.0 drivers -- you'll find the firmware at the same place and an explanation on how to flash the chipset we have on the P67A-GD65 (which has TWO identical chips to flash). The new firmware updater doesn't work on those, so you need to download an older firmware to use the older DOS program to flash with the newer .MEM files.

P67A GD65 (B3) - Boot Up Problem

Similar Messages

Maybe you are looking for