P67A-GD65 (B3) Marvel 6gb/s sATA performance?

I was talking "elsewhere" on a forum, and the topic of the marvel chip came up. It was argued that the design / implementation of the Marvel controller on these motherboards all were the 91xx series, and they all had a pretty horrifying flaw. They share a 5gb/s bus. For something that is said to support 2 6gb/s devices, that is pretty devastating, so i had to come here, where the knowledge about all things MSI is at its highest density. I mean, if the answer is out there, then it's more likely to be here, then anywhere else.
So.
Is this issue a part of the P67A-GD65 (B3) motherboard design?
Assuming the first answer is yes, is there anything you can do to minimize the impact of it?
Thank you for your time & effort.
B!

It's actually not an issue with the mainboard design, it is a problem with the Marvell controller itself. It is an add-on feature to provide SATA III function, but it is not the best. ASMedia controller isn't really a lot better either. At least the Marvell allows RAID for those that desire it. The answer is in the Intel 'native' SATA III controllers which are quite good. A lot depends on the drives used. With spinner HDD's, SATA II or SATA III doesn't make a lot of difference in their performance anyway.
Quote
Assuming the first answer is yes, is there anything you can do to minimize the impact of it?
Not really, other than maybe a Z87 with all the SATA ports Intel controlled SATA III.
Added: I have no experience with them, but maybe an aftermarket add-in SATA III controller card would work better.

Similar Messages

[P67A-GD65 (B3)] Marvell RAID Boot menu + SSD

I've looked through the manual, but I haven't seen an option to turn off the very first thing I see at boot. I think it's the Marvell RAID controller; it says no hard disk found. I guess you can press space to access some options, but I haven't tried that. I would think the option to turn something off wouldn't be there but rather in the BIOS somewhere. It seems to me this is slowing down boot a little bit. I'm more interested in having it not do what it's doing than hiding it, if those are the options.
Are there any special BIOS settings for using an SSD drive? Mine seems to be working fine, but I was wondering if there were any other options.
Thanks.

There's no option to turn it off. It's a third party RAID controller by self so you can actually ignore the message and the system will still function normally.
No special settings is needed if your SSD is working fine currently.

[BUG] Marvell SATA drivers v1051 on P67A-GD65 (B3)

Hi folks,
NOTE: After further testing, drivers 1.0.0.1047 (the ones found on the MSI website) do NOT have this issue, only the driver version 1.0.0.1051 (See post #4).
Discovered a bug on the Marvell controller drivers version 1.0.0.1051 (the ones found on the DVD that comes with the MB). MB is the P67A-GD65(B3) with BIOS 1.9
When I wake up from suspend, 4 times out of 5, my cpu will show 10%-13% of usage caused by Interrupts (shown in Process Explorer). When I open the SysInfo window of PE, I see that ~80% of the core0 is being used just for said interrupts.
This only happens when you resume from suspend (haven't tried hibernation since I won't use that). It never happens if you just boot normally.
After debugging this for a few hours (xperf traces, performance analyses, latencymon.exe), I finally figured out which driver was causing this and it turns out it's the Marvell Controller one.
1) When I disable this controller (only this one), this issue *never* happens.
2) if I uninstall this driver *while* the interrupts are going bonzo, the interrupts go back to normal.
3) when Using the default Microsoft Drivers for this controller, the issue never happens.
- To recreate, just install the drivers (and perhaps do *not* connect any drives to connectors 6-7 (or 7-8) on the mb).
- Go to sleep mode (I suspend to memory here.. not sure what happens on hibernation), then resume a few times, and you'll have the interrupts start going crazy.
Hope this is the right forum for this.. if not, I apologize in advance...
Regards,
M
P.S. This happens whether I overclock or not (currently not OCing and it happens just as frequently)

Bah! I couldn't let it go when I saw that the drivers on the MSI site were version 1.0.0.1047 instead of 1051 ( hate leaving a job unfinished).
So I decided to install the ones on the website, and they work perfectly (in regards to the interrupt after resume issue).
So, thanks for the pointer Jack . I now know that I'll be able to use the 6GB sata ports if I ever need them with the proper drivers (Microsoft's only support 3GB I believe).
/cheers
Regards,
M
P.S. Makes you wonder what they changed in 1051 though.

P67a-gd65 - how to enable marvel sata ports 7-8?

built my first pc.
using p67a-gd65.
ports 1-6 are managed by intel code, if I understand correctly. They work fine and I can see them in the bios.
ports 7-8 are managed by marvel code, if I understand correctly. They do not work and I cannot see them in the bios, but I do see a reference to marvel at boot-up.
is there something special I have to do to enable ports 7-8?
I searched the forum and can't find anything on this.
thanks in advance for any help you might provide.

I must be missing something; exactly where and how do I enable the controller?
when I look at 'system status' I see
sata port1
sata port2
sata port3
sata port4
sata port5
sata port6
and it shows the devices I have plugged in, and that is good.
I then see
e-sata port1
e-sata port2
where 'I thought' sata port7 and sata port8 would be listed, and they show a status of 'not present'.
thanks

P67A-GD65 new system bios setting recommendations and sata connections

Hey all,
My old dual core HTPC (after many hours of use) finally gave up the ghost and moved on to the great PC grave yard . I have ordered all the new upgrade parts from Newegg and am looking for recommendations on what bios settings and setup procedures I should use on the initial bootup and Windows load. I'm not looking to overclock I just want a fast stable system for video decoding and playback. It's my understanding from the manual that SATA 1-2 are controlled by the Intel P67 chip and 7-8 are controlled by the Marvell chip but I am unsure of SATA 3-6. Can SATA 3-6 do raid 0? I want to use the Crucial SSD as my primary boot drive and the 2 WD drives on raid 0 as my secondary drive. SATA connection advice (which SATA ports) and Raid Bios setting would be helpful. Should I install the raid 0 drives after I have Windows 7 loaded on the SSD? Any other setup advice is appreciated.
Here is my setup.
Windows 7 64bit
Bach HTPC case
Ultra LSP 750Pro PSU
Intel i5-2500 3.3G CPU
MSI P67A-GD65 Motherboard
Sapphire HD5570 1G RT Video Card
Crucial CTFDDAC128MAG-1G1 SSD 6.0Gb/s SATAIII (Primary boot drive)
2 WD3200KS Hard Drives SATA 3.0Gb/s (Raid 0)
Lite-on 12X Blu-Ray Burner SATA
G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600

Two questions answered. SATA 3-6 are controlled by the Intel P67 chip and do support Raid 0 but I still wonder if I should wait to install the drives until Windows has finished it's install.
SATAIII controller integrated in Intel® P67 & Marvell SE9128 chipsets
- Up to 6Gb/s transfer speed.
- Supports two SATAIII ports (SATA1~2) by P67 PCH
- Supports two SATAIII ports (SATA7~8) by Marvell SE9128
- SATA1~6 ports support RAID 0/1/5/10 mode by Intel P67 PCH
- SATA7~8 ports support RAID 0/1 mode by Marvell SE9128

Can I make a hardware raid with the on board Marvell SE9128 chip on p67a-gd65?

Hi,
as you all know the RAID 0/1/10/5/JBOD with the p67 chipset are pure software raids or "fake" raids. I saw some sata-raid pcie 2.0 x1 cards on the sell which have the Marvell SE9128 chip. So my question is: Can I make a hardware raid with the onboard Marvell SE9128 chip on the p67a-gd65?
Thanks
--pepe

Quote from: Stu on 06-November-11, 02:31:26
Hardware RAID explained:
http://www.pcguide.com/ref/hdd/perf/raid/conf/ctrlHardware-c.html
What do you want to say with this? I know what's the difference between a software (fake) and hardware raid? Your post doesn't answer the question. The p67-chipset has integrated software raid. The marvell se9128 is also found on some hardware raid cards. That's why I'm still wondering if it is for a hardware raid on this board or not.

Freezing/Hanging - Mobo Issue (P67A-GD65)?

Quote
========
Chassis - COOLER MASTER Elite 430 RC-430-KWN1 Black Steel / Plastic Computer Case
Hard Drive - Western Digital Caviar Blue WD10EALX 1TB 7200 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive
CPU - Intel Core i5-2400 Sandy Bridge 3.1GHz (3.4GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor BX80623I52400
Mobo - MSI P67A-GD65 (B3) LGA 1155 Intel P67 SATA 6Gb/s USB 3.0 ATX Intel Motherboard
PSU - RAIDMAX HYBRID 2 RX-630SS 630W ATX12V V2.2/ EPS12V SLI Ready CrossFire Ready Modular Modular LED Power Supply
RAM - Patriot Gamer 2 Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) Desktop Memory Model PGD38G1333ELK
GPU - EVGA 02G-P3-1386-KR GeForce GTX 460 (Fermi) 2GB 256-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card
CD Drive - Asus DRW-24B1ST/BLK/B/AS Black SATA 24X DVD Burner - Bulk - OEM
---------------After reading CPU temps--------------
Upgraded CPU Fan - XIGMATEK LOKI SD963 92mm HYPRO Bearing CPU Cooler bracket included I7 i5 775 1155 AMD and dual fan push pull compatible
=======
Alrighty everyone, so this might end up being a fairly lengthy article, but I want to make sure I give you all of the information so you can correctly assess.
Earlier in the year, I decided that I needed a desktop for college. I had seen people do it before and I was fairly adept at computers, so I put the computer together with the above components from newegg.
Originally, I put the desktop together in about five hours and hooked it up. Worked great, except on startup it gave (and still gives) me an error of saying "No Hard Disk Detected", however the opposite could not be truer as it found my hard drive when I loaded the OS; Windows 7. I then tested it that night with Starcraft II and it worked great; no minor bugs, nothing. The following day, I pull all of my games/programs on it including skype. Here is where things started to get weird. On Borderlands, everything went great and without a hitch, however when I started Civilization V, after playing for about an hour, it froze. And this freeze froze everything; the keyboard, the monitor, the mouse, etc. A buzzing sound came from the speakers and a hard restart was necessary. This freeze also happened again during the Multiplayer for Call of Duty Modern Warfare 2, Starcraft II (after about an hour), League of Legends and even Skype, while using my webcam. Also, in the Windows reliability program and windows events, no freeze is registered.
So I thought "oh, this is obviously overheating or a voltage problem" (the cpu temps were getting between 85-90 C's). So I fixed the RAM's voltage so it fit exactly what it needed (it required 1.65 volts, but the auto detect only gave it 1.5, so it was around .15 off). While waiting for the fan and thermal paste to come, I reinstalled Windows 7, reinstalled the drivers for all of my components and checked event viewer (which I ended up needlessly fixing an event 3011 and 3012 for corrupt performance readers).
My fan and paste came in yesterday and applied both, making my cpu super-cooled leveling off at a max of 50 C's at full load and 25-30 C's idling. The hottest component is now the GPU which usually hits 65-70 C's under full load.
At this point, I figured "great, I have been freeze-free for 2 days, let's retest", so I played two games of league of legends last night (around 1.5 hours) on skype and it froze. Again. Once I restarted my desktop to let everyone know what happened (and loaded skype and rejoined the conversation) I only got in two words before it froze again.
In summary, basically under stress, especially under games/programs requiring the internet, the computer has a full freeze, requiring a hard reset. I tried to fix the voltages (RAM) as well as cool the computer, which seemed to work only for a short while. Further once the computer freezes, whenever I turn it back on, it is more prone to freezing unless I leave it off overnight.
I'm not even necessarily looking for an answer, just an idea of where to start. Thanks again, I would really appreciate some help on this one.
=========
Update: I used Prime95 to test it as well as Intel Burn Test. No freeze during IBT, and for Prime95 it usually gets hit on the In-Place Large FFT or Blend Test. Hasn't frozen on Small FFT. I also just updated the the mobo's BIOS again to the latest one. Also, with the update, if I put the RAM's voltage at 1.65 (or anything above Auto), it won't boot the OS.
Any ideas welcome.

Quote from: bspeir on 08-August-11, 04:15:04
Right, saw this in my email inbox and thought I would respond, being the OP and all. I asked MSI what the problem was (giving all issues I had) - the response I received was
"We have to suggest you contact your reseller (The place you bought this MB from) and have them test the MB completely for you to check if this MB is faulty or not, then ask for some help.
If the reseller for some reason cannot help, we have to ask you to contact MSI distributor or MSI office near your place to seek further help" about 2-3 weeks ago (took them a month to get back).
The only problem with this, is I am a college student and half about five days left to get back to school and I NEED this desktop for school. So giving back the computer, allowing them to run tests, then waiting to return it seems like an entirely long and not necessary considering the desktop WORKS, but only on 4GB of RAM as opposed to 8GB.
However, I AM willing to check the c-state, but I will need some information first to make sure my desktop won't explode if I do this wrong.
1) What does the C-State do?
2) How do I disable it?
3) Is this really an option I should check into?
Thanks again, this community has honestly been more helpful than MSI's actual customer support.
It won't help you with your problem but I've tested C-state for a while and you can read what it will do in the link HU16E provided. I've noticed that in Idle state the usage of power drops a couple of watts, so when you have your PC in idle a lot of time and you care about power saving it's worth trying. When overclocking it can be unstable however. I have a CPU that handles all cores set to 46 with all energy settings on and auto Vcore completely stable, when going to 47 I have to compensate. The first thing I have to do is disable C-State because it will BSOD when in idle for a while. So I will suggest that if you use stock settings and care about power saving you try it and otherwise disable it.

Random lock ups with MSI P67A-GD65 (B3). Please help!

Hello all,
I just built a new system with the following components:
MSI P67A-GD65 (B3)
Intel Core i7-2600K Sandy Bridge 3.4GHz
EVGA 012-P3-1570-AR GeForce GTX 570
G.SKILL Ripjaws X Series 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800)
Thermaltake Black Widow W0319RU 850W ATX 12V PSU
Antec Lanboy air case
2X Western Digital VelociRaptor WD1500HLFS 150GB in RAID0 running Windows 7 Pro 64 bit
This was supposed to be my dream computer, but it has turned into a nightmare! It locks up constantly. Usually the mouse pointer will disappear and the computer will just freeze up. This normally seems to occur after the computer has been idle for a while. I have read that there might be compatibility issues with the MSI P67A-GD65 and the GTX 570 video cards. Can anyone confirm this? Any suggestions on how to troubleshoot this? The only thing event viewer is showing is the unexpected shutdown when I have to power cycle it. Thanks in advance!

Quote from: HU16E on 12-April-11, 11:26:00
That can happen, & it can really mess things up if two kits are attempted to be run together. The platform is DDR3 1333 as to native support by the CPU IMC. If the system can't run on 1333 RAM speed at CR 1, 9 9 9 24 @ 1.50v's, then something is wrong. No system should ever have to use an OC (or X.M.P.) as a workaround to make it work. That's why I recommended the Crucial 1333. Plug one stick in the blue primary dimm slot to get everything loaded & checked out, & go from there.
Exactly which SATA ports are you using for the HDD's & RAID? White Marvell or Intel SATA III, or the black SATA II?
Unfortunately, my local shop didn't have the Crucial, so I grabbed the Corsair instead. The Velociraptors are running from SATA 1 and 2 (the top white connectors). I also have 2X HITACHI Deskstar 2TB 7200 RPM 64MB Cache SATA 6.0Gb/s running in RAID0 from SATA 3 and 4 for storage (this computer is intended for HD video editing, compositing in After Effects, etc.). Sorry I forgot to mention that in the original post!

Blank Screen and flashing cursor on new build-P67A GD65 (B3). Help needed.

As per the title, a computer was built for me with the following specs:
CPU: Intel Core i5 2500k
Cpu Cooler: Arctic Freezer xtreme Rev 2.0,
Motherboard: MSI P67A – GD65 (B3)
PSU: Super-Flower Amazon 550W
RAM: 4GB G.Skill RipJaws-X, DDR3, 1600
HDD: 1TB Samsung Spinpoint F3 7200rpm
Graphics Card: Sapphire Radeon HD 5850 Xtreme - 1 GB GDDR5
Disc Drive: Samsung SH-223C DVD+RW
Case: Cooler Master 690 II LITE Midi-Tower
OS: Windows 7 Ultimate
Everything went ok with the build and installation of the OS. Computer was booting ok. When I took the computer home that evening, powered it on and a blank screen with a flashing cursor on top left hand corner appeared. Tried several times but failed to boot up properly. Just to note that I can enter into the BIOS and it recognizes HDD, processor, Disk Drive and RAM. What I have done so far (of course with advice from computer experts as compared to me) are the following:
1. I removed all the parts except cpu and cooler then put them back. When I restarted a message appeared that win7 need to do a repair. It went thro the process and then it stated it can’t do repair. Did this twice. When I restarted the third time, a blank screen with the blinking cursor appeared again.
2. Cleared the BIOS using the button on the outside of the motherboard and also once using the jumpers inside the motherboard. After doing this, I pressed on the “”ON” button several times (with no power on to the computer) to dissipate any current that was left there.
3. Interchanged the RAM on different slots. Also tried using only 1 stick of Ram at a time.
4. Checked the HDD on another machine and it was ok. Formatted the HDD on the other machine, plugged onto new machine and tried to install OS again but no joy.
At this point, I’m now stuck after almost a month when the machine was built. Would it be the motherboard? RAM? etc. Just wondering if I should RMA the motherboard since it is just over a month when it was delivered.
A point to note, there is a message that comes up when it is booting stating no HDD is detected. I googled this but found out it was to do with a marvel adapter that needs to be disabled or something like that. However, it was mentioned that this wasn’t going to affect the performance of the pc as the BIOS can detect all the components.
I also noticed that when I switch on the pc, there is a small pause before it kicks on then there is a long beep followed by 2 small beeps. I presume this is normal.
Any help on this will be highly appreciated?

Quote
I also noticed that when I switch on the pc, there is a small pause before it kicks on then there is a long beep followed by 2 small beeps. I presume this is normal.
Disable EuP 2013 & that should take care of the pause. The beeps are normal at startup. Only time I have observed a blank screen & blinking cursor is if the system wasn't getting enough juice to initialize, or their was insufficient power in an OC attempt. What kind of +12V amps does that PSU you have provide?

HELP! My 2011 MSI P67A-GD65 (B3) build suddenly refuses to boot

Hello, I am new to this forum because I hadn't had any troubles yet.
I built my system in July/August 2011. Here's what it has:
MSI P67A-GD65 (B3)
Intel Core i7-2600K Sandy Bridge CPU
16GB Corsair Vengeance 240-pin DDR3 1600
650w Corsair Enthusiast PSU
MSI N460GTX Cyclone 1GD5/OC GeForce Graphics Card
1x 2TB Hitachi 7K3000 7200RPM SATA 6 GB/s (With Windows 7 64-bit installed)
2x 3TB Seagate 7200RPM SATA 6 GB/s (For storage)
I have used this computer for graphics and video editing...it has served me faithfully. Yesterday evening while editing a Word document, I got "do you want to save your changes before exiting?" and of course I said yes. Then to my surprise my computer proceeded to shut down and reboot. At first I thought maybe I missed a Windows Update message telling me it would reboot in xxx minutes so I was not alarmed. But then as I watched it reboot, it gave me the POST message that there was no disc drive recognized. I thought that was weird since I never noticed it before. But then after the BIOS screen with the MSI graphics thing I was faced with a blank screen except for a flashing cursor two inches from the top of the screen. When I realized that this wasn't going to leave, I got a bit worried so I did a reset through my tower's button and same thing happened...I unplugged everything and let it sit for a few minutes... restarted 10 minutes later....same thing. Did it again and then went into my BIOS to look around. It showed no HDD's connected and I had 3 hooked up. I was concerned my HDD went bad so I connected it to another pc and accessed it with no trouble as another storage...I was happy my files are all there. So then I reconnected to my original build and got the same POST message, but this time the drives were visible in BIOS....but still no boot.
I have another blank SATA HDD so I removed all my HDD's and connected it by itself along with my SATA DVD drive and I tried to do a clean Win7 install on it. But at the point in the install process where it asks WHERE you want to install Windows, no drives showed up. So that door was closed. I tried the same thing again after swapping SATA port locations, thinking 1 was defective, but I got the same treatment from all of them...nothing recognized during the install process, although the drives are showing up in BIOS....
I think I know why the POST message is saying 'no drives detected,' though...I read it is saying that based on the SATA ports being used...I have 8 SATA's on my MOBO...4 6gb/s; 4 3gb/s. 7-8 are 6gb/s and ONLY when I have a HDD plugged into one of them does it show on the POST screen...which I still think is weird, and seems to have just started happening last night with the rest of the problems...but I could live with that since I could disable the message in BIOS I think.
But I have tried to clear the CMOS...all three ways...jumper, button, battery. I reset BIOS thru BIOS.... Nothing changes. BTW, in BIOS I ran a RAM memory check and it passed. Besides, I am not hearing any weird beeps...related to that....
I don't know why this would happen after working perfectly for 2 years... And why would it politely shut down in the beginning of the process anyways? I mean...I appreciated being asked to save my changes...but I don't know what else to do...PLEASE OFFER SUGGESTIONS...any help is appreciated.
Thank you in advance...I hope someone can help me! I am still covered by warranty...but I want to do this right.
Thanks!
Marie
EDIT: BTW, I have also tried unplugging everything from the pc except for the DVI and power plug in case that was interferring....

Quote
On a slightly different topic...would it work (I have never done this!) to take my OS HDD and boot it on another PC? I am thinking this would not work because of system files and etc., but I have always wondered this and now would be the best time for me to know
It mostly works if the components used aren't too special. As you have no RAID setup it should work. However you will need to reactivate Windows once it made it. Of course you will also need all drivers for the new machine. Be aware that you might not be able to connect to the internet before you installed the proper driver for the ethernet adapter.

Help Configuring Raid 1 & Raid 5 on the P67A-GD65 (B3) motherboard

I just purchased the P67A-GD65 (B3) motherboard for a custom system and have a few questions in regards to setting up RAID.
I have the following HDs
2x 1TB
3x 3TB
I would like to setup RAID 1 with the two 1TB drivers and RADI 5 with the three 3TB drivers. I connected the two 1TB drives to ports 7&8 so it would be using the Marvell SE9128 and the three 3TB drives to ports 1, 2,3 to use the Intel P67 (B3) PCH. The documentation says that SATA ports 1-6 support RAID 0/1/5/10 and SATA port 7-8 support RAID 0/1.
The two 1TB in RAID 1 would be my boot drives (going to run VMWARE ESXi with multiple VMs) and the three 3TB RAID 5 drives are going to be my storage.
I was under the understanding that you could use both the Intel P67 (B3) PCH and the Marvell SE9128 at the same time but it looks like I can only configure one or the other. If I have neither of the two setup I can hit CTRL + I and get to Intel or CTRL + M to get to Marvell but when I set one of them up I can’t boot into the other to setup my second RAID.
At the end of the day I bought this system to run ESXi 5.0 with multiple VMs with a shared storage area. If I can’t utilize both controllers then what’s the point of having two on the motherboard? I made sure in the BIOS settings I enabled RAID for the HDs.
If anyone has configured their systems like this please let me know how.
NOTE: As others have mentioned if you put in all your memory at one time then the system will go into a continuous reboot state. You should only put in one and then the others. Right now I have two 4GB sticks in and will add the others once I figure out is going on with the RAID.

Quote from: Jack on 29-September-11, 16:56:49
Please stop flashing the same version all over again, before something goes wrong.
It's great to have that info now... is it posted anywhere on the website?
Quote from: Jack on 29-September-11, 16:56:49
Please make sure that the memory frequency is manually set to DDR3-1333, the Command Rate to 2T and the memory voltage to 1.575V. Then retest with all modules.
I changed the frequency to DDR-1333 and Voltage but I don't know how to change the Command Rate or where it is located? Any help?
Also,
I'm still having problems getting the system to recognize the Marvell RAID config when I boot with the VMWare ESXi 5.0 CD and try to select where I want to install... When I go into the Marvell settings the system it shows that I have two dirves in RAID 1 Config:
PD 0: ST31000528AS -> PORT ID = 0; PD ID = 0; Type = SATA PD; Status = Configured; Size 953869MD; Feature Support = NCQ 3G 48Bits; Current Speed = 3G
PD 8: ST31000528AS -> PORT ID = 1; PD ID = 8; Type = SATA PD; Status = Configured; Size 953869MD; Feature Support = NCQ 3G 48Bits; Current Speed = 3G
under the HBA 0: Marvell 0 settings it says the following:
VENDOR ID: 1B4B
DEVICE ID: 91A3
REVISION ID: B1
BIOS VERSION: 1.0.0.1027
FIRMWARE VERSION: 2.1.2.1505
PCIe Speed Rate: 5.0Gbps
Configure SATA as: IDE Mode -> In the BIOS I have the settings to RAID
Not sure if it matters but here's how I have the Intel Raid setup...
RAID Volumes
ID = 0; NAME = Storage; LEVEL = RAID5(Parity); STRIP = 64KB; SIZE = 5.4TB; STATUS = Normal (it's in green); BOOTABLE = Yes
Physical Devices:
Port Device Mod Ser Size Type/Status(Vol ID)
0 Hitachi blah blah 2.7TB Member Disk (0)
1 Hitachi blah blah 2.7TB Member Disk (0)
2 Hitachi blah blah 2.7TB Member Disk (0)
Any Thoughts? I'm trying to boot from the two 1TB drivers setup in the Marvell Raid 1 Config and the Raid5 through the Intel for all my storage needs.
Thanks again for helping out.

P67A GD65 Lagging at Boot

I've been running this board for a few years now, never given me any problems except for the fact that my keyboard (a gaming one) wouldn't function properly prior to Windows loading, meaning I couldn't select an option with it during startup. Annoying, but it didn't seem to important. Eventually I discovered that later BIOS update added support for gaming keyboards and so I decided to update. I updated to version 1.19 and I also updated a number of my drivers. I then encountered a problem with my USB devices, which now appears to be resolved (in brief the computer claimed a phantom drive existed and that the device was not functioning properly) but I have now developed a problem at boot.
For as long as I have had it, when the board boots I get a screen with a blinking underscore in the top left and a two digit hexadecimal in the bottom right that changes, shortly afterwards it attempts to load from the Marvell SATA 3 ports (there's nothing plugged into them so it quickly moves on but I've often wondered if there's a way to stop it from checking in the first place) then it returns briefly to the underscore before displaying the MSI boot logo and booting Windows, all of this happening in about 5-10 seconds. Now however, it hangs at the underscore page, both times it visits, for about 30 seconds each time. The underscore doesn't blink, it's just constantly on and the number is static. This happens whether booting from cold or rebooting the system.
Does anyone know what might be causing this, or a way to fix it? Once booted the machine functions completely normally.
Specs:
MoBo: P67A GD65
Processor: i5 2500k @3.3GHz
RAM: 8GB Corsair Vengeance
GPU: nVidia GeForce GTX 560Ti
Booting Windows 7 from 120GB OCZ Vertex 3 SSD
Any help that can be offered would be much appreciated.

It was this: link. It was very cheap, bought primarily because it gave me front facing USB 3.0 ports (which are plugged into the motherboard USB 3.0 at the back). Unfortunately, while the booting issue now seems to be resolved the stability issue isn't, I got the exact same BSOD five minutes ago. I'm assuming this has all started because I updated my BIOS to make it support my keyboard. Should I try reinstalling the BIOS? Or install an earlier version? What about the drivers listed on the MSI page (Intel Management Engine Driver, Intel Chipset Driver, et al.)? I updated those when I updated my BIOS, I thought correctly but I could be wrong, what's the right way for me to check them?
Currently the times when it has crashed have been when I close Firefox pages (often Youtube) and when I play Minecraft. The crashes are always sporadic and unpredictable, sometimes everything is fine, and then it suddenly goes. A part of me wonders if it has something to do with an important file being stored on my secondary data hard drive which seems to try and spin up just before it crashes, but I'm not sure how I would go about checking for that problem, if it could even be the cause.

P67A-GD65 Does not even start

Plugged all the components.
When pressing the power button on the board, this is what happens :
1) Power button lights up
2) Reset button flash once
3) 1-6 Led just above CPU flash once,
MSI P67A-GD65 B3 Intel P67 Motherboard - ATX, Socket H2 (LGA1155), Intel P67 Express, DDR3 2133MHz (O.C.), SATA 6.0 Gb/s, Gigabit LAN, CrossFire/SLI Ready, USB 3.0
Corsair CMZ4GX3M1A1600C9 Vengeance 4GB DDR3 RAM - PC12800, 1600MHz, 1x4096MB, Non-ECC, Unbuffered
Crucial CT128M4SSD2 m4 2.5" Solid State Drive - 128GB, SATA 6Gb/s
Cooler Master HAF 922M ATX Black Mid-Tower Case - 5 External 5.25" Drive Bays, 5 Internal 3.5" Drive Bays, 2 200mm Fans, 1 120mm Fan
Intel Core i7-2600K BX80623I72600K Unlocked Processor - Quad Core, 8MB L3 Cache, 3.40 GHz, Socket H2 (LGA1155), Retail
Ultra X4 500-Watt Modular Power Supply - 135mm Fan, ATX, Lifetime Warranty w/ Registration, 80+ Bronze, ATI CrossFire Certification, Vibration Dampener Included
EVGA 012-P3-1570-AR GeForce GTX 570 Video Card - 1280MB GDDR5, PCI-Express 2.0, Dual DVI, Mini HDMI, SLI, DirectX 11
And nothing happens, the computer doesn't start.
I triple checked, and everything looks fine?
Any idea what can be the cause?
Regards

At first glance I see your PSU's maximum amps are 32A on the 12V rail.
Inspecting the power requirements for a typical system with your GPU indicates about 35A. see here https://forum-en.msi.com/faq/article/power-requirements-for-graphics-cards
As a first test can you install a less power hungry GPU ?

P67A-GD65 (B3) Screen show nothing.

Hi.
Spec :
MOBO : MSI P67A-GD65 (B3) LGA 1155 Intel P67 SATA 6Gb/s USB 3.0 ATX Intel Motherboard
GPU : MSI N560GTX Twin Frozr II/OC GeForce GTX 560 (Fermi) 1GB 256-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card
RAM : Kingston Value 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1333 Desktop Memory Model KVR1333D3S8N9K2/4G
PSU : Antec EarthWatts EA-650 GREEN 650W ATX12V v2.3 SLI Ready CrossFire Certified 80 PLUS BRONZE Certified Active PFC Power Supply
CPU : Intel Core i5-2500K Sandy Bridge 3.3GHz (3.7GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 3000 BX80623I52500K
OP : Windows 7 Home Premium 64bits
So here's my problem.
I've bought this Computer about two week ago, assembled it myself, for the first week i had no problem at all. After that the computer would sometimes, pretty often, crash and restart on it's on. When windows would be open again i would get a message telling me that it was a bluescreen, i was never able to go and look at the minidump cause each time my computer would crash again before i could reach it.
I updated all the driver i could, did as much Windows update i could, the problem persist. Seeing as i even formated and reinstalled windows i think i can say that's not the problem.
Now, i'm at the point where i can't even do anything cause the last time it crashed i lost my screen, it's all black. I can see from the MOBO that all the light for the CPU are On and i can hear the fan, but nothing else seems to happen, i tried to plug-in my speaker so that i could hear the Windows Sound when it's done loading, but nothing.
Now i'm wandering about the next step ? How do i confirm which of my component is the problem ?
Thanks for the help.
What i was doing while it crashed ? Nothing, just browsing.

Thanks for the reply.
Unfortunately i don't have another Computer to test with, i've got to use a friend's laptop to post here.
Quote
When in the OS, uncheck Automatically Restart in the Settings of Startup & Recovery. Then the BSOD will remain visible long enough to get the Stop: error code.
Well i can't reach the OS. If i'm ever able to reach it though i will do it. Is this something that i show Always do, unchecking the Automatic Restart and never checking it again ?
Quote
Clear CMOS and test with just 1 piece of RAM. Run it for a week to see if there is any issues.
Will try this.
Quote
In that message box, there is a button that allows you to expand the dialog to see the detail. That contains the BSOD code.
Yeah i already knew about this, problem is whenever i would expand the window it seemed to me that the Computer would restart faster, not giving me enough time to save that code.
Thanks again everyone.
Strange that you're suspecting the PSU, my 12v Rail should be strong enough, my first guess would have been the MOBO since i crashed in bios.

P67a-gd65 b3 Not powering up but power LED goes on

This computer I built has been running for several months with no problems. Last night I left it on and when I got up it today it was off.
Almost positive its a hardware problem as nothing new has been added or changed. Looking to see if anyone else had the same symptoms to help identify what component may be causing it.
When I unplug the machine from power, and plug it back in no LEDs light up (as expected from what I remember when building it).
When I press the power button on the case, or the power button on the motherboard, that power LED lights up but that is the only thing that seems to happen. None of the LEDs on the top by the CPU light up, the fans never spin, and no post.
First thoughts would be psu, cpu, or motherboard.
The type of psu (seasonic x series) I have would only spin its fans some of the time depending on load. So the lack of psu fan activity isn't abnormal.
Thanks

Western Digital Caviar Black WD1002FAEX 1TB 7200 RPM SATA 6.0Gb/s 3.5" Internal Hard Drive -Bare Drive
CORSAIR Vengeance 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model CMZ8GX3M2A1600C9
ASUS DRW-24B1ST/BLK/B/AS Black SATA 24X DVD Burner - Bulk - OEM
SAPPHIRE 100311SR Radeon HD 6970 2GB 256-bit GDDR5 PCI Express 2.1 x16 HDCP Ready CrossFireX Support Video Card with Eyefinity
MSI P67A-GD65 (B3) LGA 1155 Intel P67 SATA 6Gb/s USB 3.0 ATX Intel Motherboard
Intel Core i5-2500K Sandy Bridge 3.3GHz (3.7GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor BX80623I52500K
SeaSonic X Series X650 Gold ((SS-650KM Active PFC F3)) 650W ATX12V V2.3/EPS 12V V2.91 SLI Ready CrossFire Ready 80 PLUS GOLD ...

P67A-GD65 (B3) Marvel 6gb/s sATA performance?

Similar Messages

Maybe you are looking for