P67A-GD65 RAID set-up problem... HELP!

First off I tried the search to find any threads but the search didn't come back with anything relevant.
So here is my problem. Brand new build and can't get the RAID drivers to install. Can't even find the drivers by themselves without a EXE file to run them. I have them on a USB flash drive but Win7 won't recognize them because they are still bundled into the EXE program. I've tried to extract them from the Marvell RAID Drivers given on the MSI support site but still no luck. I have the MSI P67A-GD65 with two Seagate ST32000641AS Barracuda XT HDs plugged into the Marvell SATA III ports 7 & 8. Win7 install sees them as two separate drives so I'm stuck trying to find some drivers that Win7 will recognize and install off the USB drive.
Also I'm reading that the Marvell SATA III controller isn't as fast as the Intel P67 SATA III controller.... should I swap the cables over and avoid the Marvell? If so any help finding the Intel P67 RAID Drivers would be greatly appreciated.

Things have changed since my last build, thank God!
In the old days you had to install the RAID drivers before installing the OS onto the array. Today I just set up the RAID 0 array after installing Windows 7 onto one of the two drives. So all that time I spent looking for drivers that weren't part of an EXE file was a waste. I did swap from the SATA III Marvell ports (7 & 8) to the SATA III ports (1 & 2) that are Intel P67 PCH. I then installed Windows 7, popped in the MSI motherboard disc, and loaded the Intel RAID drivers. After that I opened the Intel Control Panel that was installed with the RAID drivers and set-up the RAID 0 array. Now it seems Windows 7 is migrating itself onto that array. Bad news... because the array is so large. Two 2TB drives... its going to take a long time. Not sure if there is a better/faster way.

Similar Messages

MSI P67A-GD65 infinite boot/loop problem

installed everything into my case and go to boot into the UEFI and nothing !
i press the power switch, everything starts fine and the fans spin up and the LED's on the board are fine, waits 5 secs then it shuts itself off and tries the exact same process again. it keeps doing this until i cut the power !
i've checked the 24pin etc, KB & mouse r fine, 2 different sets off RAM in every slot, cleared CMOS (i think).
seems like a very common problem with this board after a bit of googling !!
also tried
Quote
this is the 1st time ive used it !
tried the OC genie button on and off.
been sitting in the box unused for about 1.5 months. doubt that means anything tho.
put the stock cooler on securely, and still the same problem !
now tho, it wont start for about 3 secs after i press the power button
and
Quote
disconnected all the SATA's bar 1, and still the problem :/!
all the standoffs etc r fitted correctly and iv re-connected the 8 pin cpu and 24 pin. 1 stick off RAM in the 1st slot also :/!
checked no molex connectors r touching the case metal either
any suggestions?

motherboard: MSI P67A-GD65 (B3) bought on march 31st and used today for 1st time
CPU: intel core i7 2600K
CPU Cooler: tried an alpenfohn matterhorn with Scythe 1850RPM gentle typhoon Push/pull also tried the stock cooler
RAM Corsair CMD4GX3M2A1600C9 (2X2GB kit of 1600Mhz CL9 corsair dominator DDR3) and tried Patriot PSD34G1600KH (2X2GB kit of Patriot signature DDR3)
PSU Corsair TX650 650w psu
GPU XFX radeon 4870 1GB
Case NZXT M59 + mainly scythe fans and a noctua and coolermaster
DVDRW liteon DVDRW
Storage 128GB kinsgton SSDnow V100, 1TB Samsung F3 7200RPM, 1TB Hitachi 7K100 7200RPM all sata 3gb/s
Generic 5.25" fan controller
2 x 12" blue CCFL's
OS windows 7 x64 professional (installed on the SSD, but havent booted it yet as the board doesnt even get to BIOS :()
peripherals Microsoft reclusa keyboard and gigabyte GM-6990 (i think) mouse
monitor Benq g2222hdl connected via DVI
the only things i have changed today are, put the new notcua fan in my case, changed the Motherboard and CPU from and Asus M4A78LT-M & Athlon II X4 640 to MSI P67A-GD65 (b3) & intel core i7 2600k. Also, put the alpenfohn matterhorn on today.
everything is confirmed working apart from the CPU & Motherboard. everything worked yesterday, but i didnt have the necessary equipment to test the motherboard or cpu before using them together (today)
hope this will help

MSI P67A GD65 Multiplier and software problems

Hi
i just bought i5 2500k and Msi mb, it came with 1.4 bios version and the maximum multiplier that i could log into Windows was 44 even though the vcore adjustment didnt work properly
maxing out at 1.224 (bios reading) no matter the voltage set manually, I updated to 1.7B4 and i was able to get into windows at 46x100 the downside of the new bios was the memory suddenly stopped working at 2133 10-11-11-30 1.65v even 12-12-12-30 would end up in oc failed message so i had to settle for 1866. Now i updated to 1.8B5 and i can run my memory at 10-11-11-30 again no problem but
maximum muliplier went down to 44... again - theres no way to make system work with 45 or higher multiplier so basically oc-wise 1.8B5 is like 1.4 with vcore adjustment working properly/pll fix - Plz p67 users need proper bios.
Second problem is that Overcloking center crashes with 0xc0000005 code right after launching exe - first happened on my old XP SP3 so i installed fresh Win7 unfortunatelly its the same story.

Ok now im mad i flashed back to 1.7B4 and guess what i cant choose any multiplier above 44! Whats weird is that although bios version says 1.7B4 its behaving exactly like 1.8B5
Every time i changed some voltage option in bios V1.4 or V.1.7B4 the pc would power down and then power up, since 1.8B5 it would just reset. That and inability to go above x44 when just yesterday
i could go x46 (i didnt check more as i want to run my SB below 1.35vcore) makes me think my cpu is artificially locked and ability to go above x44 in 1.7B4 was just an accident that was
corrected in 1.8B5 whch has some code inside that prevents (in case somebody wants to downgrade) to update data responsible for cpu oc. Another example supporting that is that my cpu can
boot up at 4.4 ghz@stock voltage (1.168 in bios) log into windows and run some tests , of course it would freeze and reset randomly after some seconds or minutes but still... On the other hand changing the mulitplier to 45 and vcore up to 1.4v doesnt even make HDD start spinning and load WIndows after the MSI logo screen vanishes, its just seems locked.

P67A-GD65 , with Thermaltake TR2 430w HELP!!! Not working

Hi
I just got my MSI P67-GD65, I am so excited. I put it together and when I try to power it up it nothing happends
I have a thermaltake TR2 430W, which advertise Core i7 will work
This is what happends when I try to power it up
1. just a blue led blinks every 5 sec or so
2. the cpu fan just spins lightly every 5 sec
3. there are no power to the CD rom
Please can someone help me?
Is it the power supply?
TIA
Eddie

Since you asked, I had a similar setup as yours, only got no beeps, just an on/off cycle, with 4 blue LEDs and the fans turning on, then off, etc.
I changed the 4GBx2 Patriot RAM with 2GBx2 Corsairs, and it booted fine. I was able to put 1, but not both, sticks of the 4GB Patriot memory and still boot if the Corsair memory was still installed. It would not boot if the Patriot was the only memory installed, 1 stick or 2, in any slot.
The fact that you got beeps (2 low & soft, one high & loud?) means that you may have actually got past POST, as that’s what mine does when it started working. The two first beeps are likely the 2 devices (keyboard & mouse) being detected/installed, then the big ‘beep’ is done with post.
You might have a video issue, since it might have passed post but not display anything. I’d get a cheap card, and if you have another computer, try it out there just to see if the backup one works. There could be some video incompatibility still going on. For instance, my machine was outputting something like 1980x1024 and my monitor understandable didn't like it--even my ancient CRT wasn't too happy, but at least I could see something.
Hamsterman

P67A GD65 (B3) - Boot Up Problem

Every time I cold boot, I get the initial beeps, then it hangs on a black screen, with 98 in the bottom right hand corner. I have to turn the computer on and off another one to five times, before it boots up normally.
I have updated to the latest bios, disconnected every USB device, but the problem still occurs and once in Windows, I get no BSOD's whatsoever, so I'm running out of ideas.
Any ideas, before I go to Tech Support?
Thanks,
Kev

Quote from: HU16E on 19-November-11, 17:50:16
Yes. Please try it without a HDD connected. If it completes POST quickly, then it is either that one single HDD that was connected, or the Intel or Marvell controllers are most likely faulty. That would mean RMA of the mainboard for sure.
Edit: Rather than RMA, if a bad controller could be identified, Intel SATA II or III, or the Marvell SATA III, the good controlled ports could still be used. Would limit the connectivety choices though.
I tried it with no HDD's connected, no joy mate.
I've also just installed another PSU and the problem is still there, so I'm giving up and sending it back.
Cheers for your help mate, but I've given this problem a LOT of time and money and enough is enough.

Help Configuring Raid 1 & Raid 5 on the P67A-GD65 (B3) motherboard

I just purchased the P67A-GD65 (B3) motherboard for a custom system and have a few questions in regards to setting up RAID.
I have the following HDs
2x 1TB
3x 3TB
I would like to setup RAID 1 with the two 1TB drivers and RADI 5 with the three 3TB drivers. I connected the two 1TB drives to ports 7&8 so it would be using the Marvell SE9128 and the three 3TB drives to ports 1, 2,3 to use the Intel P67 (B3) PCH. The documentation says that SATA ports 1-6 support RAID 0/1/5/10 and SATA port 7-8 support RAID 0/1.
The two 1TB in RAID 1 would be my boot drives (going to run VMWARE ESXi with multiple VMs) and the three 3TB RAID 5 drives are going to be my storage.
I was under the understanding that you could use both the Intel P67 (B3) PCH and the Marvell SE9128 at the same time but it looks like I can only configure one or the other. If I have neither of the two setup I can hit CTRL + I and get to Intel or CTRL + M to get to Marvell but when I set one of them up I can’t boot into the other to setup my second RAID.
At the end of the day I bought this system to run ESXi 5.0 with multiple VMs with a shared storage area. If I can’t utilize both controllers then what’s the point of having two on the motherboard? I made sure in the BIOS settings I enabled RAID for the HDs.
If anyone has configured their systems like this please let me know how.
NOTE: As others have mentioned if you put in all your memory at one time then the system will go into a continuous reboot state. You should only put in one and then the others. Right now I have two 4GB sticks in and will add the others once I figure out is going on with the RAID.

Quote from: Jack on 29-September-11, 16:56:49
Please stop flashing the same version all over again, before something goes wrong.
It's great to have that info now... is it posted anywhere on the website?
Quote from: Jack on 29-September-11, 16:56:49
Please make sure that the memory frequency is manually set to DDR3-1333, the Command Rate to 2T and the memory voltage to 1.575V. Then retest with all modules.
I changed the frequency to DDR-1333 and Voltage but I don't know how to change the Command Rate or where it is located? Any help?
Also,
I'm still having problems getting the system to recognize the Marvell RAID config when I boot with the VMWare ESXi 5.0 CD and try to select where I want to install... When I go into the Marvell settings the system it shows that I have two dirves in RAID 1 Config:
PD 0: ST31000528AS -> PORT ID = 0; PD ID = 0; Type = SATA PD; Status = Configured; Size 953869MD; Feature Support = NCQ 3G 48Bits; Current Speed = 3G
PD 8: ST31000528AS -> PORT ID = 1; PD ID = 8; Type = SATA PD; Status = Configured; Size 953869MD; Feature Support = NCQ 3G 48Bits; Current Speed = 3G
under the HBA 0: Marvell 0 settings it says the following:
VENDOR ID: 1B4B
DEVICE ID: 91A3
REVISION ID: B1
BIOS VERSION: 1.0.0.1027
FIRMWARE VERSION: 2.1.2.1505
PCIe Speed Rate: 5.0Gbps
Configure SATA as: IDE Mode -> In the BIOS I have the settings to RAID
Not sure if it matters but here's how I have the Intel Raid setup...
RAID Volumes
ID = 0; NAME = Storage; LEVEL = RAID5(Parity); STRIP = 64KB; SIZE = 5.4TB; STATUS = Normal (it's in green); BOOTABLE = Yes
Physical Devices:
Port Device Mod Ser Size Type/Status(Vol ID)
0 Hitachi blah blah 2.7TB Member Disk (0)
1 Hitachi blah blah 2.7TB Member Disk (0)
2 Hitachi blah blah 2.7TB Member Disk (0)
Any Thoughts? I'm trying to boot from the two 1TB drivers setup in the Marvell Raid 1 Config and the Raid5 through the Intel for all my storage needs.
Thanks again for helping out.

HELP! My 2011 MSI P67A-GD65 (B3) build suddenly refuses to boot

Hello, I am new to this forum because I hadn't had any troubles yet.
I built my system in July/August 2011. Here's what it has:
MSI P67A-GD65 (B3)
Intel Core i7-2600K Sandy Bridge CPU
16GB Corsair Vengeance 240-pin DDR3 1600
650w Corsair Enthusiast PSU
MSI N460GTX Cyclone 1GD5/OC GeForce Graphics Card
1x 2TB Hitachi 7K3000 7200RPM SATA 6 GB/s (With Windows 7 64-bit installed)
2x 3TB Seagate 7200RPM SATA 6 GB/s (For storage)
I have used this computer for graphics and video editing...it has served me faithfully. Yesterday evening while editing a Word document, I got "do you want to save your changes before exiting?" and of course I said yes. Then to my surprise my computer proceeded to shut down and reboot. At first I thought maybe I missed a Windows Update message telling me it would reboot in xxx minutes so I was not alarmed. But then as I watched it reboot, it gave me the POST message that there was no disc drive recognized. I thought that was weird since I never noticed it before. But then after the BIOS screen with the MSI graphics thing I was faced with a blank screen except for a flashing cursor two inches from the top of the screen. When I realized that this wasn't going to leave, I got a bit worried so I did a reset through my tower's button and same thing happened...I unplugged everything and let it sit for a few minutes... restarted 10 minutes later....same thing. Did it again and then went into my BIOS to look around. It showed no HDD's connected and I had 3 hooked up. I was concerned my HDD went bad so I connected it to another pc and accessed it with no trouble as another storage...I was happy my files are all there. So then I reconnected to my original build and got the same POST message, but this time the drives were visible in BIOS....but still no boot.
I have another blank SATA HDD so I removed all my HDD's and connected it by itself along with my SATA DVD drive and I tried to do a clean Win7 install on it. But at the point in the install process where it asks WHERE you want to install Windows, no drives showed up. So that door was closed. I tried the same thing again after swapping SATA port locations, thinking 1 was defective, but I got the same treatment from all of them...nothing recognized during the install process, although the drives are showing up in BIOS....
I think I know why the POST message is saying 'no drives detected,' though...I read it is saying that based on the SATA ports being used...I have 8 SATA's on my MOBO...4 6gb/s; 4 3gb/s. 7-8 are 6gb/s and ONLY when I have a HDD plugged into one of them does it show on the POST screen...which I still think is weird, and seems to have just started happening last night with the rest of the problems...but I could live with that since I could disable the message in BIOS I think.
But I have tried to clear the CMOS...all three ways...jumper, button, battery. I reset BIOS thru BIOS.... Nothing changes. BTW, in BIOS I ran a RAM memory check and it passed. Besides, I am not hearing any weird beeps...related to that....
I don't know why this would happen after working perfectly for 2 years... And why would it politely shut down in the beginning of the process anyways? I mean...I appreciated being asked to save my changes...but I don't know what else to do...PLEASE OFFER SUGGESTIONS...any help is appreciated.
Thank you in advance...I hope someone can help me! I am still covered by warranty...but I want to do this right.
Thanks!
Marie
EDIT: BTW, I have also tried unplugging everything from the pc except for the DVI and power plug in case that was interferring....

Quote
On a slightly different topic...would it work (I have never done this!) to take my OS HDD and boot it on another PC? I am thinking this would not work because of system files and etc., but I have always wondered this and now would be the best time for me to know
It mostly works if the components used aren't too special. As you have no RAID setup it should work. However you will need to reactivate Windows once it made it. Of course you will also need all drivers for the new machine. Be aware that you might not be able to connect to the internet before you installed the proper driver for the ethernet adapter.

P67A-GD65 (B3 )boot problems

I've built my box around mid-December (2011) and ever since, I've experienced the same issue as well.
The very first time it happened, I ran the repair tool, but just like others said, it could not repair it. I DID NOT have have MSI control center installed for the first few weeks and yet the random reboots at the windows logo still happened, so I'm certain it is NOT an MSI control center issue (at least in general).
Yes, it is very hard to pinpoint, just like others said. Most of the time it boots just fine. On those rare occasions (maybe once every 20-40 boots) I just let it reboot automatically and then it's all fine.
I'm NOT an overclocker at all, so I have everything set as it is out of the box and aside from this random, occasional reboot everything works fine.
I don't remember which bios version originally I had, either 1.C/D/E, but I upgraded to 1.G and it still does it, and did before the bios upgrade. Currently 1.E is the latest which I don't have.
MSI P67A-GD65 (B3)
Intel i7-2600K Sandy B
G.SKILL Ripjaws Series 16GB (4 x 4GB) F3-10666CL9Q-16GBRL
ADATA S510 Series AS510S3-120GM-C SSD
Nvidia GeForce GTX 275
Win 7 x64 Ultimate

Ok, so I just want to recap on this issue. It seems my machine is stable now.
I have reinstalled windows about 4-5 times this week, trying to test what the problem might be. Wasn't sure if it's a driver, the service pack (1) or maybe the order of installation messed something up. So I wanted to start clean the various installations/testing. None helped.
So I noticed there was a new BIOS update available with v 1.I (dated 01/12/2012). As a side note, I don't understand why they post version numbers with letters (A, B, C, D, etc) but in the BIOS or in other programs, such as CPU-Z, they report the version number with numbers. Anyhow.
So I installed this BIOS. That didn't solve it either. But while I was running the OS, I noticed my BIOS LED is flashing, so my primary BIOS failed. It still booted and ran fine. I just didn't understand why did the primary BIOS failed since the BIOS update tool (downloaded from this forum, reported the flash was successful.)
I cleared the CMOS, reset the BIOS to default values, installed windows 7 ultimate x64 using AHCI and IDE mode. None made any difference. Still experienced random reboots at the Starting Windows screen (but it rebooted only once - consequent reboots were fine).
So I used the dual BIOS to re-flash the primary with the secondary. The secondary had BIOS v 1.11 (dated 04/20/2011). So now I'm running this version. Lo and behold (and also knock on wood) I don't have any random reboots so far. That's about 5 days now.
So I want to close this thread by saying, that it seems there was some issue with the new BIOS releases (I only used 1.G and 1.I) but reverting to the original one (which is in the secondary BIOS - 1.11) makes my machine ran stable without random reboots - so far.
I think this is how I'm going to leave it. This works. As they say, if it ain't broken don't fix it, so this is the BIOS version I'll stick with.
Long live the King!

P67A-GD65 new system bios setting recommendations and sata connections

Hey all,
My old dual core HTPC (after many hours of use) finally gave up the ghost and moved on to the great PC grave yard . I have ordered all the new upgrade parts from Newegg and am looking for recommendations on what bios settings and setup procedures I should use on the initial bootup and Windows load. I'm not looking to overclock I just want a fast stable system for video decoding and playback. It's my understanding from the manual that SATA 1-2 are controlled by the Intel P67 chip and 7-8 are controlled by the Marvell chip but I am unsure of SATA 3-6. Can SATA 3-6 do raid 0? I want to use the Crucial SSD as my primary boot drive and the 2 WD drives on raid 0 as my secondary drive. SATA connection advice (which SATA ports) and Raid Bios setting would be helpful. Should I install the raid 0 drives after I have Windows 7 loaded on the SSD? Any other setup advice is appreciated.
Here is my setup.
Windows 7 64bit
Bach HTPC case
Ultra LSP 750Pro PSU
Intel i5-2500 3.3G CPU
MSI P67A-GD65 Motherboard
Sapphire HD5570 1G RT Video Card
Crucial CTFDDAC128MAG-1G1 SSD 6.0Gb/s SATAIII (Primary boot drive)
2 WD3200KS Hard Drives SATA 3.0Gb/s (Raid 0)
Lite-on 12X Blu-Ray Burner SATA
G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600

Two questions answered. SATA 3-6 are controlled by the Intel P67 chip and do support Raid 0 but I still wonder if I should wait to install the drives until Windows has finished it's install.
SATAIII controller integrated in Intel® P67 & Marvell SE9128 chipsets
- Up to 6Gb/s transfer speed.
- Supports two SATAIII ports (SATA1~2) by P67 PCH
- Supports two SATAIII ports (SATA7~8) by Marvell SE9128
- SATA1~6 ports support RAID 0/1/5/10 mode by Intel P67 PCH
- SATA7~8 ports support RAID 0/1 mode by Marvell SE9128

High voltage on Low Vdroop Setting P67A-GD65 + 2600k

Dear members of the MSI-HQ user forum,
My attempts on overclocking my 2600k processor has been stalled for quite some time now.
I've been at 4.3GHz for a very long time because I wish to keep my Vcore set on Auto (I don't want my voltage set manually because it will remain at that voltage all the time).
I've been playing around with a lot of settings and none of them have worked.
The main problem is I want to be stable at 4.3GHz but with Vdroop set to Auto, it will only deliver 1.288V during a Prime95 torture test. 1.288V is not enough because after 10 min. I will get the 0x124 Bluescreen, which is too little Vcore. I have manually found out that 1.296V will do the trick! But again this is set manual... After switching to Vdroop set to Low Vdroop the Vcore voltage JUMPS to 1.42V during stress test (Prime95 & IBT)!! Waaaay too high. This will only get worse if I set my processor speed to 4.4GHz, Vcore will then be 1.44/1.45V and so on..
Bios is updated to version 1.H. I updated from 1.8 to 1.C to 1.H, didn't make any difference. I've also played around with bios settings but nothing solves my problem. Eup 2013, spread spectrum, C1E, Overspeed protection all disabled. Tried all C1 states. PLL overvoltage disabled & enabled. Memory both tested @ 1333MHz & 1600MHz auto&linked settings (according to spec). And so on.
I really want to overclock further then 4.3GHz (at least that one stable) using Auto Vcore. Or my voltage is too low (Vdroop set to auto) or too high (Vdroop set to Low). Please help :(
My system specs are:
Windows 7 64Bit
Intel i7 2600k
MSI P67A-GD65 (B3)
Corsair XMS3 8GB 1600MHz dual channel memory kit

To quote from a recent Ivye Bridge article:
Quote
Today Intel defines three different voltages for every Sandy Bridge CPU: LFM, nominal and turbo. LFM is the lowest frequency the CPU can run at (e.g. completely idle), nominal is the frequency it is specified to run at (e.g. 3.3GHz for a 2500K) and turbo is the highest available turbo frequency (e.g. 3.7GHz for a 2500K). Intel determines the lowest voltage possible for each one of those frequencies. Sandy Bridge obviously runs at more than just three frequencies, there are many more intermediate frequencies that it may run at depending on the current workload. The voltages at those intermediate frequencies are interpolated from the three points that I mentioned above.
There is no definition above that, and it becomes an extrapolation of a voltage above 3,7GHz. Considering that each CPU has slightly different characteristics, even within the defined frequency range, there is no knowing what each one will do and require outside that range. So the required voltage at those overclocked frequencies can vary quite a bit, and the extrapolated voltage range in auto voltage mode at a given frequency may not be enough for the individual sample, furthermore, it is limited in terms of the maximum it will consider and apply in auto mode. Once that critical point is reached, one has to be satisfied or resort to manual intervention.

Problem with downgrading bios. MSI P67A-GD65 (B3).

Hi!
I'm having problems with downgrading my bios from version 4.3 to 1.19. I want to downgrade, because 4.3 doesn't want to boot when I use xmp settings for my RAM ( that might be related to my CPU since I have i5 2500k which is 32nm and 4.3 version of BIOS is recommended for 22nm processors ). When I try to flash with the MSI Forum HQ USB Flashing Tool I'm getting an error: "Rom file ROMID is not compatible with existing BIOS ROMID". I've ran out of ideas how to downgrade my bios so I'm asking you for help. My specs:
MOBO: MSI P67A-GD65 (B3)
CPU: INTEL CORE i5 2500K
RAM: G.SKILL RIPJAWS X 4GB (2x2GB) DDR3 1600MHZ CL6 (F3-12800CL6D-4GBXH)

Here you go. GD65 and GD55 usde the same BIOS files;
https://forum-en.msi.com/index.php?topic=179837.msg1295420#msg1295420

Degraded RAID set help

Hello Support Community,
I have a 4 bay RAID set that all of a sudden is showing as degraded. I have two pairs of disks each striped, and then have those two pairs mirrored. Not sure if this is a correct RAID format, but it is what it is right now. So both striped sets say online, with no problems, but my mirrored set of those two pairs shows that it is degraded. See below.
Any thoughts as to what might be happening? I have the options set to automatically rebuild the RAID. How do I know this is happening? How long should I expect this to take? It's a 4TB raid in it's current config, and there is about 3.7TB of data on this RAID. I have everything backed up in two other locations. Am I better off starting from scratch? Or should I just let this thing run for 2 weeks and see what happens? Any help would be greatly appreciated.
Thanks
Dave

No, I was doing all of this in disk utility. I left the arrary running overnight, and it's back online now. Not sure what got screwed up.
Thanks

P67a-GD65 (b3) boot problem (reboot and select proper boot device)

Hello All,
I have the following problem;
When I start my computer sometimes it starts normal or I get the following warning;
Reboot and select proper boot device.
If this happens, its stays for a few seconds on A2 at the lower right corner , then MSI mainboard screen, and then the above warning.
When i use the reset button, it starts normal or same problem.Sometimes i need to restart it like 5-7 times to get it started normal.
My system info:
Mainboard: MSI P67A-GD65 (MS-7681)
Chipset: Intel Sandy Bridge
Processor: Intel Core i7 2600K @ 3400MHz
Physical Memory: 4096MB (2 x 2048 DDR3-SDRAM)
Video Card: AMD Radeon HD 6900 Series
Hard Disk: Seagate ST31000528AS ATA Device (1000GB)
Hard Disk: Seagate ST3200822AS ATA Device (200GB)
Hard Disk: Seagate ST3200822AS ATA Device (200GB)
DVD-Rom Drive: XMTQ FGPIR0DURGHI
DVD-Rom Drive: Toshiba Samsung SH-S223C CDDVDW
Monitor Type: LG L1915S - 19 inches
Monitor Type: ACER X233H - 23 inches
Network Card: Microsoft Virtual WiFi Miniport Adapter
Network Card: Wireless-N 300 USB Adapter WNA3100
Operating System: Windows 7 Ultimate Professional, Media Center 6.01.7600 (64 bit)
DirectX: Version 11.00
Windows Performance Index: 5.9 on 7.9
Mainboard bios: 1.9
Hopefully someone can help me.
Thanks,
Tammo

Zalman ZM660-XT
AC Input Range Voltage 100VAC ~ 240VAC ±10% DC Output
Frequency 50Hz~60Hz Output V. Output Load Rating Combined
Power
AC Input Current
(Rated) 115VAC 9.5A Imin Imax Ipeak
230VAC 4A +3.3V 0.8A 30A 35A 155W 660W
PFC Type Active PFC +5V 0.5A 30A 35A
Power Factor 99% Maximum
+12V1 0.5A 20A 22A 636W
Inrush Current Limit
(@ Cold start at 25°C) 115VAC 80A +12V2 0.5A 20A 22A
230VAC 60A +12V3 0.5A 20A 22A
Efficiency 88% Maximum @230VAC, Typical load +12V4 0.5A 20A 22A
DC Output
Voltage
Regulations Output V. Regulation Range At Full
Load -12V 0.0A 0.8A 22.1W
+3.3VDC ±5% +3.14V~+3.47V +5VSB 0.1A 2.5A 3.5A
+5VDC ±5% +4.75V~+5.25V Protection Features
+12V1DC ±5% +11.4V~+12.6V Over Voltage Protection(OVP)
+12V2DC ±5% +11.4V~+12.6V Over Current Protection(OCP)
+12V3DC ±5% +11.4V~+12.6V Short Circuit Protection(SCP)
+12V4DC ±5% +11.4V~+12.6V Over Temperature Protection(OTP)
-12VDC ±10% -10.8V~-13.0V Under Voltage Protection(UVP)
+5VSB ±5% +4.75V~+5.25V Ambient Temperature
DC Output
Ripple
& Noise Output V. Specification At Full
Load Operation 0°C ~ +40°C
+3.3VDC 50mV Storage -20°C ~ +80°C
+5VDC 50mV Ambient Humidity
+12V1&2DC 120mV Operation 5%RH ~ 95%RH
+12V3&4DC 120mV Storage 5%RH ~ 95%RH
-12VDC 120mV Dimensions
+5VSB 50mV 180(L) x 150(W) x 86(H) mm

Problem with raid set on xserve

Hi to all!
I hope you can help me with a big problem that I have with a Xserve of the work.
Yesterday afternoon I come to the work and my partners mentioned to me that the web pages were not going. I tried to connect with ARD but he was not answering. I had to move to the building where the server is racked and when I connected a monitor a it was showing me a folder icon with an interrogation icon.
Since this had happened to me in my Mac of the office once, I initiated from the installation DVD to see if I could repair permissions and/or the discs with the Disk Utility. For my surprise (and terror) does not show any volume or disk except the DVD.
I got into the RAID Utility in the menu and there I could see the discs but the RAID Sets does not appear... We had mounted since we install the machine a raid 5 with 3 discs and 2 volumes on this raid set.
Then, from the Terminal, doing "diskutil list" it's show no volume on any disk.
I suppose that something has happened with the volumes and the raid cannot be mounted...
Is there any way to mount the volumes again? Something similar to the "fixmbr" that I believe that there are in others OS to restore the volumes tables...
Is there any way to mount again the RAID without losing the information from the discs?
Do you know that can be happening?
PS: It is a Xserve of the last ones, with Mac OS X 10.6.8. I have already tried to reset the PRAM and it keeps on doing the same.

The Server Monitr does say anything. It doesnt pick up any server. I tried to add the XServe in the Server Monitor, but it keeps waiting for a reply after I have put in the username, password and IP address.
It is an XServe with a Mirror software RAID on the 2 x Internal Hard Drives within the XServe
I am not using the SAN software
There have been reports of fault latchs on the Apple Drive Bay Modules. Do you think this could be causing the units to dismount?

P67A-GD65 (B3) problem

Here are my specs:
P67A-GD65 B3 (bios v1.8)
i5 2500k
8GB(2x4) DDR3 Corsair XMS3 1600
GTX260 216
Teamgroup Xtreem S1 SSD 60gb (boot drive)
Win 7 64 bit
I have searched for a solution to my problem ,yet didn't find it so thought i'll post it here:
The MB ,CPU ,RAM and SSD where bought about 2 weeks ago brand new.
A few days ago i have experienced bad youtube/vimeo/(virtually all flash player video based sites) video playback (corrupted colors ,see attached image) ,corrupted images in browser (also a screenshot below) and artefact photoshop brushes (when painting in ps ,the brush showed similar to the youtube video playback ,random colors corruption). I thought it's the browser (firefox 4) so i installed chrome ,same problem ,also in opera an IE8 so it's a hardware/driver problem.
At first i suspected a bad memory stick. I've tested them with memtest 3.5 from a bootable CD in dos mode ,in dual-channel ,individual sticks and in all ram slots. ZERO errors. The EFI memory tool also gave me 0 errors and also windows memory manager tool said there are no errors.
Now i suspect the motherboard. Another problem i had with the mb: it kept freezing in idle so i disabled all green-power settings ,speed step ,C1E and EIST which solved it.
I must state that i have no BSoDs ,no hangs/freezes/artefacts in 3d aplications and games, hdd played movies run perfectly fine and the pc runs ok.
I tried reinstalling my graphics drivers ,yet no result. No overclocking was applied to the system.
What can it be? I am out of answers ,google didn't helped me.
Thank you in advance.

Quote from: sjay on 19-April-11, 06:47:43
Did you reset the bios before usage after flashing CMOS?
Obviously something wrong with the USB driver, perhaps the mobo USB driver?
It was already reseted to defaults.
I have never had a usb problem ,this is completely new to me.
Quote from: HU16E on 19-April-11, 06:48:23
Just for clarification sake, the black ports are all SATA II & run by the Intel controller. The two white ports closest to the RAM slots are SATA III & also controlled by Intel controller. The other two white ports, 7 & 8 are the SATA III Marvell controlled.
Ok ,sorry ,i misunderstood then. Strange ,after moving them to the white ports ,they show up at boot ,in the black ports it always said no HDD installed/detected.
Ok ,so what now? it seems i jump from a problem into another ,lucky me...

P67A-GD65 RAID set-up problem... HELP!

Similar Messages

Maybe you are looking for