P6N SLI PLATINUM CMOS BAD CHECKSUM ERROR TIME DATE

I have the same problem. It’s driving me crazy. Here is my specs:
MSI P6N SLI Platinum LGA 775
Intel Core 2 Duo E6420 2.13GHz 4M shared L2 Cache
Foxconn GeForce 7900GS 256MB 256-bit GDDR3 PCI Express x16
Western Digital Caviar SE16 WD7500AAKS 750GB 7200 RPM
Kingston KHX6400D2LLK2/2G 2GB kit PC2-6400 800MHZ
LG DVD GSA-H50N DVD-R 18X
Matsu"I'm a potty mouth"a Floppy drive
Windows XP 32-Bit
CoolerMaster RP-500-PCAR – 500W
+3.3V +5V +12V1 +12V2 -5V -12V +5VSB
20A 20A 16A 16A 0.8A 0.8A 2.0A
Sometimes the computer boots ok, and everything works great.
Sometimes it just doesn’t boot, it just gives a blank screen. So, I press reset and the post gives the CMOS CHECKSUM BAD. F1 to setup F2 to default.
If I go to the setup everything is just like I left, including the time. Even if I setup the bios with default configuration, the problem continues.
Here is a list of everything I have tried
1) Replaced the battery 2 times. I checked with a multimeter. It’s 3V allright
2) Disconnected everything leaving only 1GB memory and the graphics card
3) Updated the bios version several times, to make sure I did it ok. I cleared the CMOS after allright
4) I read every post in this forum about bios and P6N SLI Platinum
5) Already checked the D-BRACKET. It shows 4 green leds when the screen is blank
6) Already checked fans: CPU and graphics fans works ok
7) Already tested with memtest86+ V2.01
8) Already upped the northbridge to 1.325V, CPU 3 notches and the memory another 3 notches.
So anyone has any ideas, or I’ll just have to go to a computer store and swap the graphics or the PSU and try to see if the problem vanishes??? It’s gonna be tough… they don’t like to let you test the merchandise….
PS: Thanks for all the help so far that you have been giving to TheGimp, after all, we have the same problem…

I had the same problem after ~8months of trouble free service; it was intermittent too. sometimes it would boot fine, others times i'd get the error message. I removed the battery to test it. it was fine. i cleared the cmos with the button while the battery was removed. i noticed that the battery holder seems not to be anchored to the board at all. I haven't confirmed this but it looks like the protruding metal clip holds it all together. i had contacted MSI support about the problem earlier. they told me to clear the cmos. i asked about the battery holder not being secure on the board, and, as in the typical support response to an unusual question, they gave me some vague, undecipherable response. So, anyway when i put the battery back in, i felt the holder kind of click into place. I haven't had any problems since.

Similar Messages

P6N Sli Platinum event viewer error

On my new P6N Sli Platinum mainboard, every time I boot up I get the following error in the event viewer log:
"The ForceWare IP service service failed to start due to the following error:
The system cannot find the path specified. "
I think this has to do with Nvidia network drivers. The network seems to work ok, although I have by default two network controlelrs: one labelled "1394 Net Adapter" and another "NVIDIA nForce Networking Controller". Which of these that handles the actual connection seems to change randomly, but it doesn't seem to affect the performance.
I'm running Windows XP Pro SP2 with all the updates from winupdate.
Does anyone else have the same issue?

Quote from: Isandhlwana on 20-April-07, 21:51:28
On my new P6N Sli Platinum mainboard, every time I boot up I get the following error in the event viewer log:
"The ForceWare IP service service failed to start due to the following error:
The system cannot find the path specified. "
I still get this error in event viewer each time I start up. I went to administrative tools->services and tried to enable the Forceware IP Service manually: system cannot find the path specified. The path box in the service properties is empty.
After googling I found that the service corresponds to the following executable: nsvcip.exe. This file is not found in my system. Is this normal? Does anyone else of you have this file?
Apart from the error message in event viewer my system is functioning perfectly.

P6N SLI Platinum - ERROR - not enough space to copy PCI option rom

Can Someone Help Me with this Problem?
I have P6N SLI Platinum motherboard, after I plug in two INLINE Silicon Image 4xSata PCI Raid adapter (Sil-3114) bios is displaying Error message - ERROR - not enough space to copy PCI option rom
I have the lastest BIOS..
Is there eny cure for this Problem?

Quote from: kakalake7 on 24-March-07, 04:34:46
Can Someone Help Me with this Problem?
I have P6N SLI Platinum motherboard, after I plug in two INLINE Silicon Image 4xSata PCI Raid adapter (Sil-3114) bios is displaying Error message - ERROR - not enough space to copy PCI option rom
I have the lastest BIOS..
Is there eny cure for this Problem?
How's everything at your side now?

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

P6N SLI Platinum not booting after CPU change

I just upgraded the CPU in my machine with a P6N SLI Platinum motherboard from a E6700 to an E8500. I first upgraded the BIOS to 1.7 as the MSI page seemed to indicate that was a pre-req for this CPU. The machine was working fine for a day with the new CPU.
I changed the CPU in the machine and when I tried to boot, the lights on the motherboard came on as well as the fan, but no video or sound. In addition none of the diagnostic LEDs on the D Bracket light up. They had been previously working. Neither do the lights on my memory sticks light up.
I tried clearing the CMOS by hitting the switch but nothing. I am now going to try switching back CPUs but I don't have much hope that that is the problem given the diagnostic LEDs don't light. Does anyone have any suggestions as to a fix or is this motherboard fried?
P.S. Do you hit hte CMOS clear switch when the computer is off but the motherboard is charged? Or do you unplug the computer and wait for the internal orange light to go out as well too?

Quote from: Henry on 24-January-10, 11:41:19
What is the QC number (by the cpu socket) is 01, 02, or 03?
See this thread for more:
https://forum-en.msi.com/index.php/topic,123486.msg932471.html#msg932471
Ah. Given I bought my P6N SLI Platinum 3.5 years ago when they first came out I imagine mine is one of the older versions that doesn't support 45nm CPUs by default. Is there a photo somewhere showing where the QC number is located exactly on this MB? It's probably located under my huge CPU heatsink and I'm not going to remove that for a third time just to check.
I really wish the MSI CPU compatibility page mentioned that. It would save me a lot of time. It's not worth my time and effort to dismantle my PC, send them the MB and wait for them to send me back a compatible one.
I verified the BIOS upgrade by looking at the version number at startup and using CPUZ.

P6n sli platinum cannot boot up

Hello
Everytime I boot up the D bracket suggests the computer is failing on initializing the floppy drive controller. i have changed the cable, and changed the floppy drive but same effect.
In the BIOS, if I go through and F10 for no save and exit, it then exits to bank screen as it fails at the point above. If i make any changes in the BIOS, and then try to accept those changes it freezes on pressing either Y or enter. At that point all I can do is turn off and start again. Naturally it doen't retain those changes. I have done this several times to disable the floppy.
I have removed the battery and put it back, (It's 16 months old). It then did allow me to disable floppy but still machine did not go beyond the above point. Whenever I have tried to go back into the Bios again, it will now freeze when I try and accept any change in settings.
As you will see I am unable to even boot from a floppy at this point so cannot een consider updating the BIOS. However before yesterday it has been working perfectly.
Any suggestions, or the loan of an axe to reprogramme the ****** thing would be much appriecated.
Thank you
Malcolm
Motherboard P6N SLI Platinum, G52-73501x1-Q05
2.20.0050.10 BIOS verison
Intel Core 2 Duo Processor
Sony MPF920 floppy
4 Harddrives. Boot is IDE, then 3 others, one of which is sata
2 memory sticks, 2 gb ram
Plexwriter CD
Pioneer DVDRW 105
Pioneer DVD
DMX-6fire soundcard
HD620W power supply
full details not known as mostly stored on the computer
No faults on system since it was built 16 months ago

Quote from: yokochanie on 03-October-08, 13:55:28
Motherboard P6N SLI Platinum, G52-73501x1-Q05
2.20.0050.10 BIOS verison
Intel Core 2 Duo Processor
Sony MPF920 floppy
4 Harddrives. Boot is IDE, then 3 others, one of which is sata
2 memory sticks, 2 gb ram
Plexwriter CD
Pioneer DVDRW 105
Pioneer DVD
DMX-6fire soundcard
HD620W power supply
full details not known as mostly stored on the computer
No faults on system since it was built 16 months ago
"2 memory sticks, 2 gb ram"
That doesn't talk much, we need full details about it.
"Intel Core 2 Duo Processor"
Which one?
"2.20.0050.10 BIOS verison"
That's not your BIOS version, look here how to check==> https://forum-en.msi.com/index.php?topic=113146.0
What VGA you use?
Remove power cord from the PSU and leave just one memory stick in 1st DIMM, once done proceed with >>Clear CMOS Guide<<
Then try to boot, if no change disconnect any storages{4 HDD's, 3 Optical drives, and any USB devices which you may have attached} and re-test.

P6N SLI Platinum

I recently built a new computer with the P6N SLI Platinum mobo. The cpu (Intel Duo 2 Core E4300), vid card (evga 8800 GTS), memory (mushkin 2gbddr2 800), hd (Maxtor 320 gig SATA), and psu (apevia atx 500 watt) are all new. When the computer boots, all the fans and leds come on, but the monitor doesn't get a signal and the screen is black. I reseated the vid card and tried dvi/vga adaptor and a different monitor. The orange light and green light on the mobo are on. I used the pcie power 6 pin plug for the vid card. The 24 pin and 4 pin power connections to the mobo are ok. I haven't seen the bios because of the black screen. I also cleared the cmos and still no signal. I also tried an old Voodoo 2 pci vid card without the 2d pass through option and still no signal (don't know if that would work any way, but worth a try). The optical drives and the hd spin so they seem ok. I installed the D bracket with the lights to the usb header and jdb header. Should I see lights on this D bracket when the computer is booting? I don't see any and I don't get any beeps.

I now have no lights on the D bracket after clearing cmos again. I tried booting with one stick of ram and no change, then I tried booting with no ram and no change (no D bracket lights and no beeps). At this point, I have very little plugged into mobo - 1 hd, two optical drives, cpu, 2 fans and that's it.
Here are the ps specs:
Model
Brand APEVIA
Model ATX-CW500WP4
SPEC
Type ATX
Maximum Power 500W
Fans 2
PFC No
Main Connector 20 + 4Pin
Dual +12V Yes
PCI-E Connectors 1 x 6Pin
Power Good Signal 100-500ms
Hold-up Time >10ms at full load
Efficiency > 70% under max range load
Over Voltage Protection Yes
Overload Protection Yes
Input Voltage 115/230 V
Input Frequency Range 50/60 Hz
Input Current 12A @ 115AC, 6A @ 230AC
Output +3.3V@17A, +5V@25A, +12V1@16A, +12V2@18A, [email protected], [email protected], [email protected]
MTBF 100,000 Hours
Approvals UL, CSA, TUV, CE
Features
Connectors 1 x Main connector (20+4 pin)
1 x 12V (P4)
6 x peripheral
2 x SATA
1 x PCI-E
2 x Floppy

P6n SLI PLATINUM bios v1.2

So I upgraded to 4gb ram finally, and have got it to work without errors in dimm slots 2 and 4, and have been having performance issues such as slow loading, stuttering in games, and just in general slowdown with loading up applications, but absolutely no crashes or freezes of any kind, no BSODs or anything else that would be hardware related I assume.
Defragged, fresh install of windows 7, video card drivers updated and everything else checks out fine. The only thing I can think of is that over in HardForum doing a google search brought me to this post:http://www.hardforum.com/showthread.php?t=1164174 with issues related to 4gb on the mainboard having slowdowns with older bios versions.
Seeing as how this is relevant to me getting new memory, my patriot memory gave out with BSODs so I was forced to upgrade but had way better performance with just 2gb stick of ram (even in win7).
Should I do a bios update?
Specs:
EVGA 8800gts 540mb 195.62 driver
4gb A-Data ram 5-5-5-12 2t clock, 1.9v
Windows 7 64-bit
Bios v1.2 A7350NMS P6N SLI Platinum Socket LGA-775
Core2duo E6600 @2.4ghz
I haven't really done much upgrading since I purchased this a few years back, and quite surprised to see the hit and stuttering in performance in games all of a sudden after upgrading to new ram, and the ram tested out fine for 3 days straight doing multiple passes with memtest 4.0. I tried doing it in DIMM slots 1 and 3 but have been getting errors, maybe I've got a bad board?
Quite confused as to what step I need to take next, thanks for any help!

Quote
Should I do a bios update?
Yes. >>Use the MSI HQ Forum USB flasher<<

MSI P6N Sli Platinum won't Post with E8500

Ok, I've been pulling my hair out on this one off and on for a couple of weeks, and I figured I'd finally just post here and hope for some advice.
I recently bought a C2D E8500 CPU on newegg to replace the E6420 I currently have running in my system. The motherboard is a P6N SLI Platinum with the v1.7 Bios. The problem is that whenever I swap the E8500 in for the E6420 the computer powers on, fans start spinning, and then it just sits. No beeps, no lights, nothing. When I put the E6420 back in the whole thing boots up just fine. I've cleared the CMOS two different ways (removing the battery and hitting the CMOS reset button), and nothing seems to help. I have tested the CPU in another machine, and it works just fine. The MSI tech support has told me that the problem shouldn't be happening, and has suggested that I RMA the board to them. I'd rather not be without my computer for 3-4 weeks, so I figured I'd post here and see if anyone had any advice before I pull the whole system apart and send the MB in.
PSU is a 700W OCZ
Graphics Card is EVGA 9800GT 512MB
Ram is 4GB AData
Let me know if anyone sees any obvious problems.
Tim

I please have a look here:
https://forum-en.msi.com/index.php?topic=123486.msg932471#msg932471
Sending the board to MSI to be serviced is probably your only option to solve this.

COMIC BOOTING on P6N SLi Platinum

I run P95 stable for more than 12hrs using Q6600 on P6NSLi Platinum with foll. settings. vcore- +0.2375V, fsb vtt +20% FSB 1620MHz MEM - 2.00V NB- 1.45V SB- 1.60V C1E/ HPET/ EIST -disabled. Mem runnin @ 810MHz @5-5-5-18
problem arises when i switch off the power including the mains. when i boot up next time it doesnt boot & i have to reset my bios. after that i cant directly feed in 1620MHz because it doesnt boot in the range of 1500MHz-1649MHz in 1st attempt. i have to feed in a value above 1650MHz n then restart with 1620MHz. if i dont switch off mains then this problem doesnt arise. i have changed my BIOS battery to no effect.i also have flashed to d latest BIOS which on d contrary has added 1 more problem..it doesnt recognise Multipiers if i change them..i changed from 9 to 8 on my Q6600 & still in d settings including CPU-Z it shows 9 inspite showing 8 in BIOS. how do i solve this problem?
My rig
Intel Q6600, MSI P6N SLi Platinum, 1gb*4 gskill pc6400 ram @ 5-5-5-15 2.0v, EVGA 9600Gt ko version, 1sata, 2 ide hdds, sata dvd burner, TRUE120 wid arctic coolin mx-2

I should also state that when I look at the 'Event Viewer' in component services (I'm running XP SP 2),there are many erropr messages relating to 'service control manager which lists all sorts of issues) and warning messages relating to the DHCP.
This is the message that I get under the warning heading..........
''Your computer was not able to renew its address from the network (from the DHCP Server) for the Network Card with network address 00D09EC701E2. The following error occurred:
The semaphore timeout period has expired. . Your computer will continue to try and obtain an address on its own from the network address (DHCP) server. ''
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp................
Does this help in any way. Does anyone have any idea why my connection keeps hanging???

P6N SLI Platinum - intermittent video fault

I have recently bought the following parts:
Intel Core 2 Duo E6420, 2.13GHz, 1,066FSB, 4MB
MSI P6N SLI Platinum
Akasa Ultra Quiet Active PFC 500 watts PSU (3.3V/30A, +5V/30A, +12V1/18A, +12V2/18A, -12V/0.5A, +5Vsb/3A)
2 x 1GB Crucial PC2-5300 Non ECC CL5
XFX GeForce 8600GTS 256MB DDR3 PCIe (PV-T84G-UDF3)
1 x Western Digital Caviar 160GB 7200rpm, S300, 16MB SATA (system disk)
3 x Western Digital Caviar 500GB 7200rpm, S300, 16MB SATA (data disks)
BIOS – 1.1 updated to 1.3, default settings (I'm not overclocking)
Windows XP SP2 OEM
When I got everything installed and wired up I turned on the power and saw the MSI spaceship screen for a couple of seconds then the screen when blank. The computer sounded as though it was continuing to boot up and eventually settled down with 4 green lights on the D-bracket 2 connector. I powered down and physically re-fitted the video card a couple of times and it seemed to work OK. A couple of days later, after successfully installing the OS and other applications, the same thing happened again. Once more I took out and re-fitted the video card and this seemed to do the trick. After this happened a couple more times I concluded there was a fault with the video card and sent it back for a replacement (efficiently handled by Dabs). This duly arrived and as soon as I fitted it in the same thing happened again!
I’ve checked all the PSU connections and everything is where it should be. The fault does not seem to be connected to the temperature of the processor or GPU and in fact seems to happen most often when the computer has not been on for a while. I can continue to access data on the hard drives over my home network so everything else appears to be working even when there is no video. I can now pretty reliably get the video working again by switching off, putting the computer case on its side and then re-fitting the video card – power back up and hey presto everything is fine for a while until it happens again a few days later.
I’m mystified. I presume there is some kind of problem with the motherboard but would appreciate any suggestions for a solution before I take the computer to pieces again and send that back for a replacement.
Many thanks,
Peter

hmm... this is a strange problem. Reseating the video card, hmm... but is it every power on you will still see the MSI screen? can you go to the BIOS and disable the MSI spaceship screen? something like disable POST logo etc. And see if there is any error message? It might not be your video card.

Alternative IEEE drivers for the P6N SLI Platinum?

Long story short, now that I upgraded to Windows 7 (64bit), I can't stream video from my camcorder to my computer anymore, however it turns out that my camcorder also supports firewire, and wouldn't you know, so does my P6N! Or so I thought at least.
I buy a firewire cable and plug my camcorder into my comp... nothing. I figure the cable is bad so I buy a new one. I plug it in and... nothing. So I try to install some software from the website (The camcorder is a Sony Handycam DCR-HC20) and... nothing.
Sony's telling me to go bug windows, where as Windows is telling me to go bug Sony, however the only other problem I see hinted at when i search for solutions is that perhaps the drivers im using for my firewire ports are bad, so I need different ones. The thing is i don't know where to go to get reliable IEEE drivers, so I guess it'd be best to ask you guys.
Here's a rundown of my comp:
Windows 7 64bit (However chances are if any solution works for Windows Vista 64bit, it WILL work for Windows 7, so don't be shy about any solutions you may have)
P6N SLI Platinum
Handycam DCR-HC20
Oh yeah, i'm not sure which BIOS i'm using, however I don't recall ever flashing it so i would assume its the one that it was shipped with.
Thanks you for your time.

Quote from: DaLoona on 16-August-09, 21:54:16
Maybe a silly question, but did you connect the firewireconnection on your motherboard to the port on your case?
Hahaha, its all connected but i can imagine someone doing that, haha.
All kidding aside though, now that I think about it my computer only recognizes 2 firewire ports when there's 3 (one on my soundcard, 1 on the motherboard itself, and the extra one that I plugged in myself that came with the motherboard).
I guess I could fiddle with the added one but is there any reason why the firewire port on the actual motherboard itself wouldn't register my hardware being plugged in? I really wish I had another computer I could test it on, or at least something else that's firewire capable but I can't find anything, so the only other thing I can think of is the port on the camera is dead, which I SEVERELY doubt because its in perfect working order and hasn't been used that often in the few years that i've had it.

P6N SLI Platinum random shutdowns

System:
MSI P6N SLI Platinum MoBo
Intel E6750 CPU
Etasis 850W PSU
Corsair CM2X1024-6400C4 RAM (using only 1 stick while troubleshooting)
MSI NX8600GTS GPU
OK, this is a strange one. I put my new system together and everything seemed to be working fine. POST looked OK, and I was even able to install Windows. Everything seemed stable.
One thing that troubled me was that the lights on the D-Bracket were all red AFTER POST. In other words everything was working, but the LEDs were showing CPU problem. I tried everything I could think of to get the lights to go away, but nothing worked. I disconnected all HDs, DVD, and floppy drives. I reset the BIOS, and reseated the CPU. I tried putting RAM in different slots, tried both sticks solo, but nothing made any difference.
It was getting late, so I decided to go to bed and run memtest86+ over night. When I got up this morning the system had powered itself down. When I turned it on again it powered itself off within a minute of being turned on. This was with all the drives hooked up, so I disconnected everything and now it's been sitting happily in the BIOS for over 30 minutes.
So at this point, it seems like it could be a power supply issue. Unfortunately, I don't have another PSU with an 8-pin CPU connector that I can try in this system. Any thoughts? Next steps to try?
Other possibly useful facts:
When I boot into the BIOS the D-Bracket lights show #3 green, and all others red, indicating "initializing keyboard controller". But when I boot past the BIOS to a CDROM or Windows, they show all red, indicating "CPU problem"
The system makes a brief chirp the POST screen. It doesn't sound like a beep code to me, and I've heard some boards will do an "everything's OK" beep like this. But it could be important so there it is.
Although it seems happier with all the drives disconnected (indicating a PSU problem), it still shows all red LEDs on the D-Bracket (indicating a CPU problem).
This is not the first system I've built, and I was fairly careful about putting everything together the right way. The only goof I know of is that at one point I was unplugging and re-plugging things and I ran the system for a while without connecting PCIE power to the GPU. Could that have broken something?
Any help would be much appreciated.
-Steve

UPDATE: I tried hooking up my old 400W PSU with 20-pin ATX and 4-pin CPU connectors (apparently this is OK to do) but there was no change. Still four red LEDs.
I also tried removing the PCI-E GPU and booted it up with an antique PCI VGA card. Again, no change. Maybe I really did get a bad CPU?
Any other ideas, before I try to return my CPU?

Is there a new bios coming for P6N SLI Platinum for E8400 ?

Hi everyone,
( My system specs are in the signature )
I have been thinking to upgrade my cpu to E8400, but after some time passing through the forums, internet and asking some of my friends, I have decided not to. This is because I have seen many people frustrated and trying get their E8xxx's working on their moboard with endless efforts because of the wrong information given in the CPU support list of P6N-SLI Platinum. Yet, I have seen that only a few people have managed to get it work but with risky, manual adjustments.
So here is my question, will there be a new bios for P6N SLI Platinum that will make E8xxx series post without any adjustments for the users that want to stick with their P6N SLI Plat.?

Please ask here:
http://ocss.msi.com.tw/

P6N SLI Platinum crashes from cold boot

Intel Core 2 Duo E6420, 2.13GHz, 1,066FSB, 4MB
Zalman CNPS9500-AT Intel LGA775 Aero Flower Cooler
MSI P6N SLI Platinum
Neste ECS 6001 600 watts PSU (3.3V/24A, +5V/30A, +5VSB/3A, +12V1/18A, +12V2/18A, +12V3/18A, +12V4/18A, -12V/0.5A)
2 x 1GB Crucial PC2-5300 Non ECC CL5
XFX GeForce 8600GTS 256MB DDR3 PCIe (PV-T84G-UDF3)
1 x Western Digital Caviar 160GB 7200rpm, S300, 16MB SATA (system disk)
3 x Western Digital Caviar 500GB 7200rpm, S300, 16MB SATA (data disks)
BIOS – 1.1 updated to 1.5, default settings (I'm not overclocking)
Windows XP SP2 OEM
I installed the above system last summer and have been having problems ever since. Initially the video signal dropped after booting so I replaced the graphics card. This didn’t work so I replaced the MOBO. All was OK for a while then the system started crashing for no apparent reason but would usually be OK for a while after re-booting. Then it failed to boot into Windows at all. I checked the BIOS and noticed that the Smart Fan setting in the H/W Monitor had disabled itself somehow (I had set it to be enabled with a target temperature of 40OC). I re-enabled the setting and was able to boot into Windows OK. However it still crashes every time from a cold boot (the CPU fan comes on full speed for a few seconds then the computer just shuts down). After a few re-boots it settles down and seems to be fine.
I’m assuming the problem is something to do with CPU temperature but in the BIOS H/W monitor the system and CPU temperatures are never above 30 to 35OC. As the system seems to be perfectly stable once it’s been re-booted a few times it doesn’t seem that the CPU is actually overheating. I’ve tried setting the CPU target temperature higher (say to 60 OC) but still get the same cold boot crash. Note that the MSI Dual Core Centre utility in Windows shows the same CPU and system temperatures as the BIOS monitor (although the GPU temperature is much higher at 60 OC).
Any suggestions for solving this would be much appreciated.

I'm not familiar with your brand of ps. Have you tested the rails while the system is running using a digital voltage meter?

P6N SLI PLATINUM CMOS BAD CHECKSUM ERROR TIME DATE

Similar Messages

Maybe you are looking for