P6N sli platinum not working

Hi all,
I have a problem, i bought my self a P6N sli platinum, so i installed it but it doesnt work:(
I am not getting any vga signal, i know i installed it alright but it isnt working.
I think its my cpu it might not be working with this P6N, i hope anyone can confirm this, because when i check the CPU support at the MSI site it says its compatible.
I got a : Pentium 4, 3.2 mhz 640 2m/800fsb
I hope i get an answer because i have to return the P6N in 5 days, if it isnt working.
thx

Quote from: Maesus on 03-June-07, 15:44:15
Core 2 Duo will perform WAY BETTER than Pentium 4. It is 100% compatible to Pentium 4. Do you know what Pentium 4 model number you have?
Pentium 4, 3.2 mhz
640 <--this is the model number http://www.intel.com/products/processor_number/chart/pentium4.htm
2m/800fsb
O yes and non of the lights on the D-Bracket go on, the green light and orange light on the P6N are on.

Similar Messages

MOVED: P6N sli platinum not working

This topic has been moved to Intel Core Duo and Core 2 Duo based boards.
https://forum-en.msi.com/index.php?topic=108834.0

Quote from: Maesus on 03-June-07, 15:44:15
Core 2 Duo will perform WAY BETTER than Pentium 4. It is 100% compatible to Pentium 4. Do you know what Pentium 4 model number you have?
Pentium 4, 3.2 mhz
640 <--this is the model number http://www.intel.com/products/processor_number/chart/pentium4.htm
2m/800fsb
O yes and non of the lights on the D-Bracket go on, the green light and orange light on the P6N are on.

P6N SLI Platinum not booting after CPU change

I just upgraded the CPU in my machine with a P6N SLI Platinum motherboard from a E6700 to an E8500. I first upgraded the BIOS to 1.7 as the MSI page seemed to indicate that was a pre-req for this CPU. The machine was working fine for a day with the new CPU.
I changed the CPU in the machine and when I tried to boot, the lights on the motherboard came on as well as the fan, but no video or sound. In addition none of the diagnostic LEDs on the D Bracket light up. They had been previously working. Neither do the lights on my memory sticks light up.
I tried clearing the CMOS by hitting the switch but nothing. I am now going to try switching back CPUs but I don't have much hope that that is the problem given the diagnostic LEDs don't light. Does anyone have any suggestions as to a fix or is this motherboard fried?
P.S. Do you hit hte CMOS clear switch when the computer is off but the motherboard is charged? Or do you unplug the computer and wait for the internal orange light to go out as well too?

Quote from: Henry on 24-January-10, 11:41:19
What is the QC number (by the cpu socket) is 01, 02, or 03?
See this thread for more:
https://forum-en.msi.com/index.php/topic,123486.msg932471.html#msg932471
Ah. Given I bought my P6N SLI Platinum 3.5 years ago when they first came out I imagine mine is one of the older versions that doesn't support 45nm CPUs by default. Is there a photo somewhere showing where the QC number is located exactly on this MB? It's probably located under my huge CPU heatsink and I'm not going to remove that for a third time just to check.
I really wish the MSI CPU compatibility page mentioned that. It would save me a lot of time. It's not worth my time and effort to dismantle my PC, send them the MB and wait for them to send me back a compatible one.
I verified the BIOS upgrade by looking at the version number at startup and using CPUZ.

P6N SLI Platinum - Not Posting

Dbracket LEDs showing - Initializing faulty drive controller
LED 1/3/4 - Green
-- LED 2 - Red
This is a brand new system. Would adding another floppy drive help to solve this problem? Or is the built-in floppy controller busted?
CPU - E6600 Conroe 2.4GHz
RAM - G.Skill x4 1 GB ddr2 800
Vid Card - BFG Tech 7950GT 512
PSU - Antec 550w trio
Unable to pass post and we have no visual on the monitor. Please advise with regards to further action to take. I oft see suggestions of removing RAM and booting with a single stick. Is this advisable towards troubleshooting? Or is this something that isn't passed previous to the floppy controller check that is coming up faulty? Thanks in advance.
Edit: Attempted to boot with different 1 stick of RAM variations. On one attempt recieved brief life on the screen as it toggled between analog and stereo and was then unresponsive after a few seconds along with each subsequent attempt.

Quote from: BOSSKILLER on 03-June-07, 11:38:46
so with one memory stick system booting normal?
No with 4, or with just 1 of the 4 sticks (placement being in the DIMM slot nearest the CPU) our results are the same as my initial post. We have nothing visable on the screen, just black, all connections were secure, power to cpu, 24 pin in correctly, all we ever recieve is 1/3/4 green on the LED and 2 red denoting floppy disk problems. We can't even get into bios as we have nothing on the screen.
Also, I should note that we are imaging a hd on the computer next to it and are swapping the monitor when we are booting up the new system so the monitor does in fact work.

What the most stable quality 4gb (2x2gb) memory for the P6n SLi Platinum?

Hi,
I'm looking for the most stable and very good quality 4gb of ram for the P6N sli platinum MB - what make does everyone recommend for this board?
I note that Kingston value ram is mentioned on the Approved list but I wanted something faster than the valueram?
Does anyone have either G.Skill or super talent and if so how do they work? Any other makes that you can recommend?
I know that there have been issue swith 4gb of ram for Xp/Vista 32 bit systems but from what I am reading hopefully the next bios should resolve this ...?
Thanks as this is the only item that's holding up my build now !

I don´t know whats the most stable 4GB solution is, I only can tell you, that I use Micron/Crucial mamory for years and never had any problems.
Actually in my new P6N-SLI Platinum are working 4 1GB dimms of crucial value ram ddr2-667 without problems.
There is a new bois version 1.22 for the platinum which solved the 4GB problem of earlier bios versions.
That was a bios problem and not a problem of the ram.
Manufacturer as Gskill on their GBHZ6400 modules and OCZ on their 1066 SLI modules are using the same Micron chips called D9GMH which are on my values.
They have great potential above the rated 667 speed. Cause i´m coming from germany and at the moment the prices of memory here are very cheap, a lot of people are thinking about upgrading their memory.
All what I read about here in germany G.Skill, Mushkin(very expensive), OCZ, A-data, TeamGroup are the most reliable rams
when it comes to high speeds and low latency modules.
At least I recommend the Crucial Ballistix ddr800 if you are not able to handle special settings in the motherboard bios.
And of course there are coming 2GB modules from most of the manufacturers, so you only need 2 modules for 4GB.
It´s your choice...
greetings from germany
gonzos-revenge

Followup-- MSI P6N SLI Platinum does not work with E8400

I am just following up like I said I would... and the *RMA'ed* E8400 still fails to post with a BIOS updated (v1.6) P6N SLI Platinum. It works fine with an E4500... but not the E8400. MSI really shouldn't say it's compatible when it's not. I am going to send the board back to Directron and replace it with the new Gigabyte GA-EP35-DS3L. Very unhappy with MSI right now and probably won't buy from them again. I'm going to stick with another gigabyte for now. Anything I can do before sending it back tonight? I am very disappointed, especially because this really is a perfect board for me.

You can drop MSI an email to see if you are able to get an engineering BIOS to try out.
>>How to contact MSI.<<

P6n sli platinum NB fan -included or not

hello all
First post
-been viewing the site for ocing tips and such, currently running my p6n sli platinum with a e4300 @ 2.8ghz on stock colling and stock voltage, thanks to all that posted about bios settings etc. But thats neither here nor there.
But heres my problem:
So i didnt get a NB fan in my mobo box.. but a google on p6n sli platinum northbridge fan hits TONS of resellers and reviews of the board all saying its in there.
*and by tons i mean almost every result for pages..
so i called msi and they told me they dont make one.. then they said they make it for other boards and it fits this one, but it doesnt come with the board.. then they told me they did make them but dont stock them.. then they told me its an optional item and it can be ordered for 7$ plus shipping. So i told them that all the review sites and resellers say its there and they just said, no, its option and its 7$ plus shipping and that is their "final answer".
So... Did everyone get a fan or not? i realy want to know whats going on, newegg states that its part of the accessories, but since it doesnt list it as an accessory on msis official msicomputer.com site they tell me its not included and they know that its not because its not on the site. (for the record none of their boards list removable nb fans on the site and i know of a few that DO have it) I just want to see whats going on here.
So to all p6n sli platinum owners: Did you get a NB fan in your retail package?
Thanks

Quote from: ugzz on 09-June-07, 01:54:19
hello all
First post
-been viewing the site for ocing tips and such, currently running my p6n sli platinum with a e4300 @ 2.8ghz on stock colling and stock voltage, thanks to all that posted about bios settings etc. But thats neither here nor there.
But heres my problem:
So i didnt get a NB fan in my mobo box.. but a google on p6n sli platinum northbridge fan hits TONS of resellers and reviews of the board all saying its in there.
*and by tons i mean almost every result for pages..
so i called msi and they told me they dont make one.. then they said they make it for other boards and it fits this one, but it doesnt come with the board.. then they told me they did make them but dont stock them.. then they told me its an optional item and it can be ordered for 7$ plus shipping. So i told them that all the review sites and resellers say its there and they just said, no, its option and its 7$ plus shipping and that is their "final answer".
So... Did everyone get a fan or not? i realy want to know whats going on, newegg states that its part of the accessories, but since it doesnt list it as an accessory on msis official msicomputer.com site they tell me its not included and they know that its not because its not on the site. (for the record none of their boards list removable nb fans on the site and i know of a few that DO have it) I just want to see whats going on here.
So to all p6n sli platinum owners: Did you get a NB fan in your retail package?
Thanks
Mine came with one. I used it for a day and yanked it. It is WAY too loud - like louder than my case fan, CPU fan and GPU fan combined. You'd have to be stone cold deaf for me to recommend this cooler. It really is that bad.

P6N SLI Platinum - ERROR - not enough space to copy PCI option rom

Can Someone Help Me with this Problem?
I have P6N SLI Platinum motherboard, after I plug in two INLINE Silicon Image 4xSata PCI Raid adapter (Sil-3114) bios is displaying Error message - ERROR - not enough space to copy PCI option rom
I have the lastest BIOS..
Is there eny cure for this Problem?

Quote from: kakalake7 on 24-March-07, 04:34:46
Can Someone Help Me with this Problem?
I have P6N SLI Platinum motherboard, after I plug in two INLINE Silicon Image 4xSata PCI Raid adapter (Sil-3114) bios is displaying Error message - ERROR - not enough space to copy PCI option rom
I have the lastest BIOS..
Is there eny cure for this Problem?
How's everything at your side now?

MSI P6N SLI Platinum + E6850 + 533Mhz (PC-4200) RAM?

Hi,
I got hold of an E6850 (1333 MHz FSB) CPU for upgrade and I would like to know if it can run with 2Gb hynix RAM (533MHz PC-4200) on my MSI P6N SLI platinum (Rev 1.0). If it will run, how much performance loss would there be compared to using 667MHz or 800MHz RAM?
Thanks.

I am not sure if the Nforce Chipset/Memory Controller is able to support a memory bus speed that is lower than FSB Clock Speed. Intel Chipset usually can't do that (1:1 usually being the minimum ratio supported). However, on your board, the memory speed is not directly tied to the FSB Clock Speed and can be adjusted independently, so the situation may be different. The bottom line is: I can't tell you for sure if it will work or not and therefore suggest to simply test it and see what happens.
Quote
If it will run, how much performance loss would there be compared to buying PC-6400 800MHz RAM?
With the memory bus running slower than the Front Side Bus, there will be definately be a performance difference that is not insignificant.

P6N SLI Platinum random shutdowns

System:
MSI P6N SLI Platinum MoBo
Intel E6750 CPU
Etasis 850W PSU
Corsair CM2X1024-6400C4 RAM (using only 1 stick while troubleshooting)
MSI NX8600GTS GPU
OK, this is a strange one. I put my new system together and everything seemed to be working fine. POST looked OK, and I was even able to install Windows. Everything seemed stable.
One thing that troubled me was that the lights on the D-Bracket were all red AFTER POST. In other words everything was working, but the LEDs were showing CPU problem. I tried everything I could think of to get the lights to go away, but nothing worked. I disconnected all HDs, DVD, and floppy drives. I reset the BIOS, and reseated the CPU. I tried putting RAM in different slots, tried both sticks solo, but nothing made any difference.
It was getting late, so I decided to go to bed and run memtest86+ over night. When I got up this morning the system had powered itself down. When I turned it on again it powered itself off within a minute of being turned on. This was with all the drives hooked up, so I disconnected everything and now it's been sitting happily in the BIOS for over 30 minutes.
So at this point, it seems like it could be a power supply issue. Unfortunately, I don't have another PSU with an 8-pin CPU connector that I can try in this system. Any thoughts? Next steps to try?
Other possibly useful facts:
When I boot into the BIOS the D-Bracket lights show #3 green, and all others red, indicating "initializing keyboard controller". But when I boot past the BIOS to a CDROM or Windows, they show all red, indicating "CPU problem"
The system makes a brief chirp the POST screen. It doesn't sound like a beep code to me, and I've heard some boards will do an "everything's OK" beep like this. But it could be important so there it is.
Although it seems happier with all the drives disconnected (indicating a PSU problem), it still shows all red LEDs on the D-Bracket (indicating a CPU problem).
This is not the first system I've built, and I was fairly careful about putting everything together the right way. The only goof I know of is that at one point I was unplugging and re-plugging things and I ran the system for a while without connecting PCIE power to the GPU. Could that have broken something?
Any help would be much appreciated.
-Steve

UPDATE: I tried hooking up my old 400W PSU with 20-pin ATX and 4-pin CPU connectors (apparently this is OK to do) but there was no change. Still four red LEDs.
I also tried removing the PCI-E GPU and booted it up with an antique PCI VGA card. Again, no change. Maybe I really did get a bad CPU?
Any other ideas, before I try to return my CPU?

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

Is there a new bios coming for P6N SLI Platinum for E8400 ?

Hi everyone,
( My system specs are in the signature )
I have been thinking to upgrade my cpu to E8400, but after some time passing through the forums, internet and asking some of my friends, I have decided not to. This is because I have seen many people frustrated and trying get their E8xxx's working on their moboard with endless efforts because of the wrong information given in the CPU support list of P6N-SLI Platinum. Yet, I have seen that only a few people have managed to get it work but with risky, manual adjustments.
So here is my question, will there be a new bios for P6N SLI Platinum that will make E8xxx series post without any adjustments for the users that want to stick with their P6N SLI Plat.?

Please ask here:
http://ocss.msi.com.tw/

P6N SLI Platinum crashes from cold boot

Intel Core 2 Duo E6420, 2.13GHz, 1,066FSB, 4MB
Zalman CNPS9500-AT Intel LGA775 Aero Flower Cooler
MSI P6N SLI Platinum
Neste ECS 6001 600 watts PSU (3.3V/24A, +5V/30A, +5VSB/3A, +12V1/18A, +12V2/18A, +12V3/18A, +12V4/18A, -12V/0.5A)
2 x 1GB Crucial PC2-5300 Non ECC CL5
XFX GeForce 8600GTS 256MB DDR3 PCIe (PV-T84G-UDF3)
1 x Western Digital Caviar 160GB 7200rpm, S300, 16MB SATA (system disk)
3 x Western Digital Caviar 500GB 7200rpm, S300, 16MB SATA (data disks)
BIOS – 1.1 updated to 1.5, default settings (I'm not overclocking)
Windows XP SP2 OEM
I installed the above system last summer and have been having problems ever since. Initially the video signal dropped after booting so I replaced the graphics card. This didn’t work so I replaced the MOBO. All was OK for a while then the system started crashing for no apparent reason but would usually be OK for a while after re-booting. Then it failed to boot into Windows at all. I checked the BIOS and noticed that the Smart Fan setting in the H/W Monitor had disabled itself somehow (I had set it to be enabled with a target temperature of 40OC). I re-enabled the setting and was able to boot into Windows OK. However it still crashes every time from a cold boot (the CPU fan comes on full speed for a few seconds then the computer just shuts down). After a few re-boots it settles down and seems to be fine.
I’m assuming the problem is something to do with CPU temperature but in the BIOS H/W monitor the system and CPU temperatures are never above 30 to 35OC. As the system seems to be perfectly stable once it’s been re-booted a few times it doesn’t seem that the CPU is actually overheating. I’ve tried setting the CPU target temperature higher (say to 60 OC) but still get the same cold boot crash. Note that the MSI Dual Core Centre utility in Windows shows the same CPU and system temperatures as the BIOS monitor (although the GPU temperature is much higher at 60 OC).
Any suggestions for solving this would be much appreciated.

I'm not familiar with your brand of ps. Have you tested the rails while the system is running using a digital voltage meter?

P6N Sli Platinum front audio panel and CPU temp voltage issues

Hi All,
I got my P6N Sli Platinum yesterday, build up my computer without any major issues. However I have noticed that my audio front panel does not work. It could not detect my microphone when i plug it into front auido panel, it works fine for the rear auido panel though.
Another issues is I highly doubt the accuracy of CPU temp sensor. Msi 's software monitor reports my CPU temp is around 19-20 degree, I know that's too good to be true even I am using a water cooling system. Btw my cpu is E6600. Anyone else has the similar issues?
The third, I notice my CPU voltage is bouncing between 1.1 to 1.24 in CPU-z. And the multiplier is changing from 6 to 9, frequency is changing from 1.6g to 2.4g. I only see this in CPU-z. Msi 's own software reports CPU running at 2.4g though. Is this cpuz issue or something else?
Finally, any tips to max the overclock potential of this board? I have overclocked to 3.1g but there are some crashes. Going higher the board just won't boot up. I read a review on anandtech.com says 1.22 bios is good for oc. Where can i download that? I only found 1.1 bios on official site.
Any reply will be appreciated.
Cheers

Quote
Another issues is I highly doubt the accuracy of CPU temp sensor. Msi 's software monitor reports my CPU temp is around 19-20 degree, I know that's too good to be true even I am using a water cooling system. Btw my cpu is E6600. Anyone else has the similar issues?
C2D-CPUs have a digital internal sensor to monitor CPU Core temperatures. Have a look at those with Core Temp ( http://www.thecoolest.zerobrains.com/CoreTemp/ ). This Tool reads the temperature data directly from the register of your CPU. There is nothing wrong with the sensor. It is rather the MSI tool that does not read the data it provides correctly.
Quote
The third, I notice my CPU voltage is bouncing between 1.1 to 1.24 in CPU-z. And the multiplier is changing from 6 to 9, frequency is changing from 1.6g to 2.4g. I only see this in CPU-z. Msi 's own software reports CPU running at 2.4g though. Is this cpuz issue or something else?
There is no issue. What CPU-Z allows you to see there is the C1E-feature of your CPU at work. When there is nothing to do your processor will automatically reduce Core Voltages and frequency to save power and keep temperatures down. As soon as the work load increases the multiplier is set back to x9 and core voltages increase dynamically. It is meant to be a good thing.
I have overclocked my system a little and I like that the C1E feature is still working at this speed setting CPU frequency to 2GHz and core voltage to 1.144v when my system is idle.
If you have problems with this feature you can turn it off in BIOS. The option is labeled as "C1E Support" and might be hidden somewhere. You may be able to hit "F4" to unhide it.
The MSI utilities are not the best tools to monitor your system. CPU-Z, Core Temp, Everest, Speedfan, Memset, Rightmark Memory Analyzer for example do a far better job.

P6N SLI Platinum, audio driver update gives "No Driver was supported..."

I have the audio driver from the CD that came with the mobo, but I wanted to update it to the new version. Currently I have R1.67 2.32, I tried to install the driver (R1.83 2.51) from http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=1140 but get the message "No Driver was supported in this driver package".
Also, I went to the Realtek site and got their even newer driver R1.84 but it asked me to remove the previous driver first, I'd rather check with the boards first to see what is going on.
P6N SLI Platinum
BIOS 1.4
Realtek Audio onboard

Could you please point me to where I can locate Live BIOS, first I hear of it. Thanks for the input btw.
Another off topic question. Does the Dual Core Center work ok with Vista x64? Wondering just in case before I get to using it. On my first Vista install is seemed to work, 2nd format it would come up with 2 error messages and not start:
"Error! unable to load ntuneoem.dll" and "Failed to load overclocking driver! This program must run as an administrator."
I have ntune installed on my 2nd format (which I found out doesn't work in Vista 64 properly) but cannot uninstall it from Add/Remove. A wizard window comes up and closes in the same seconds when I click uninstall. Tried to uninstall using the MSI CD which with I loaded it, still gives an error (tried to google the error msg but the msg is extremely rare and doesn't point to the problem). Going to have to manually remove it it seems and hope I get it all.

P6N sli platinum not working

Similar Messages

Maybe you are looking for