P6N SLI Platinum Reboots on Cold Start

I have the noted board with an E6750 CPU and 4GB of RAM. Problem also occurred when I only had 2GB of RAM.
When I cold boot, even if the machine has only been turned off a minute or two, the system boots and loads correctly, but after 3-4 minutes it will shut down. No messages, no warning, just black screen. If I immediately flip the power switch and bring it back up the system boots and loads then runs perfectly - until I shut it down again.
Any ideas on what could be causing this? I've had the problem since the day I built the system. Boots, shuts down after a few minutes, then boots and runs forever. I've installed a new hard drive with a fresh OS install and the problem remained. I've installed a different video card (same drivers) and the problem remained.
This isn't a show-stopper, it just tweaks me that I can't isolate and fix the problem. Any thoughts would be appreciated.

As an update, I installed a Corsair 750W PSU. Still have the problem. Thing is, while installing the PSU I heard the BIOS beep four times on a cold boot. After it warmed up and shut down I rebooted again. That time, only the single BIOS beep. I shut down again, let it get cold, rebooted - and got 4 beeps once again. After it booted and shut down I immediately rebooted, got just the single beep and - as usual - the system was stable.
What I read about BIOS beeps is that 4 short ones mean there's a memory or motherboard problem. I ran MEMTEST and there were no memory errors, so I'm guessing the problem is the motherboard.
But I did get a new PSU out of the deal!
System Specs:
MSI P6N SLI Motherboard
AMI BIOS V1.6 (error also occurred under different BIOS versions)
Intel E6750 CPU 2.66 GHz
Corsair TWIN2X2048-6400 PC6400 Memory (4GB - 4 1GB sticks) (error also occurred with 2GB)
Corsair CMPSU-750TX power supply
Dual EVGA 8800GT GPUs (error also occurred under single 8800GT installed and single 7950GT)
Western Digital HDD WD6400AAKS 640GB SATA (error also occurred on a different hard drive)
Windows XP Home SP3 (error occurred under SP2 as well)
Thermaltake VM3000A tower case[/size][/size]

Similar Messages

P6N SLI Platinum crashes from cold boot

Intel Core 2 Duo E6420, 2.13GHz, 1,066FSB, 4MB
Zalman CNPS9500-AT Intel LGA775 Aero Flower Cooler
MSI P6N SLI Platinum
Neste ECS 6001 600 watts PSU (3.3V/24A, +5V/30A, +5VSB/3A, +12V1/18A, +12V2/18A, +12V3/18A, +12V4/18A, -12V/0.5A)
2 x 1GB Crucial PC2-5300 Non ECC CL5
XFX GeForce 8600GTS 256MB DDR3 PCIe (PV-T84G-UDF3)
1 x Western Digital Caviar 160GB 7200rpm, S300, 16MB SATA (system disk)
3 x Western Digital Caviar 500GB 7200rpm, S300, 16MB SATA (data disks)
BIOS – 1.1 updated to 1.5, default settings (I'm not overclocking)
Windows XP SP2 OEM
I installed the above system last summer and have been having problems ever since. Initially the video signal dropped after booting so I replaced the graphics card. This didn’t work so I replaced the MOBO. All was OK for a while then the system started crashing for no apparent reason but would usually be OK for a while after re-booting. Then it failed to boot into Windows at all. I checked the BIOS and noticed that the Smart Fan setting in the H/W Monitor had disabled itself somehow (I had set it to be enabled with a target temperature of 40OC). I re-enabled the setting and was able to boot into Windows OK. However it still crashes every time from a cold boot (the CPU fan comes on full speed for a few seconds then the computer just shuts down). After a few re-boots it settles down and seems to be fine.
I’m assuming the problem is something to do with CPU temperature but in the BIOS H/W monitor the system and CPU temperatures are never above 30 to 35OC. As the system seems to be perfectly stable once it’s been re-booted a few times it doesn’t seem that the CPU is actually overheating. I’ve tried setting the CPU target temperature higher (say to 60 OC) but still get the same cold boot crash. Note that the MSI Dual Core Centre utility in Windows shows the same CPU and system temperatures as the BIOS monitor (although the GPU temperature is much higher at 60 OC).
Any suggestions for solving this would be much appreciated.

I'm not familiar with your brand of ps. Have you tested the rails while the system is running using a digital voltage meter?

P6N SLI Platinum – endless reboot loop. Need help!

P6N SLI Platinum – endless reboot loop. Need help!
Configuration;
Windows XP Pro, SP-2
On old hard drive (Maxtor) I installed in the new case
OCZ GameXStream OCZ700GXSSLI ATX12V 700W Power Supply
MSI P6N SLI Platinum
EVGA 256-P2-N550-T2 7600GT
INTEL Dual Core E4400
MEMORY tried two different ones;
GeIL Esoteria 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400)
Kingston Value Ram 1GB 667MH (of course tried in different slots, stick @ time)
NEC DVD player/burner
Old Maxtor IDE drive W/OS (I have new Seagate serial but won’t install it until I get everything else running.
Computer goes in an endless reboot cycle. First, showing a black screen with small parallel white hash marks. Can pull up Bios but that’s as far as I can go. At first, I thought the high end Geil memory might be at fault. But after installing the more generic Kingston I get the same looping.
In Bios, it is reading all my hardware; CPU, memory, hard drives, temperatures, voltages, etc. the only thing it doesn’t specifically show is the Evga video card. I don’t know if there is really any place it would show except in Hardware Profile.
One other thing, Bios is showing the NEC as the Primary IDE Master and the Maxtor as the Secondary IDE master (although I have tried it both ways). I generally like to boot first from my DVD then go to hard drive.
I don’t know where to go from here. Can anyone give me some suggestions?
Thanks,
Clickman

two replies;
To Vernonion
With JUST new Sata drive & DVD I get message "Reboot & select proper boot device or insert boot media in selected boot device & press a key" in other words, install windows. No flashing anything.
To Maesus
Yes, have tried boot sequence every which way . DVD functions as I ran Memtest for 4 hours last night.
I think I will use the information mentioned in the 3 links V gave me earlier to "repair" the OS on my old Maxtor drive. It is partitioned with OS in one area by itself, docs in another partition, programs another, etc. so I wouldn't lose any work. At worst, I might have to reinstall some programs. At best, I accomplish what I set out to do.
Many thanks,
Clickman

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

P6N SLI Platinum BIOS issue...

So I purchased an e8400 processor after the 1.6 BIOS update came out for my P6N SLI Platinum, got it yesterday. I put the processor in and it didn't work . I turned to Google to have the internet fix the issue, and it seems if I adjust some options in my BIOS, it may make the e8400 work. Two of the things it said to change were EIST and C1E. I went into my BIOS, and tried hitting F4 in the CPU menu to get C1E to show up, but it won't. The EIST option is no where to be found either...
Anyone else running into the same issue, or got a e8400 to work after changing stuff in the BIOS?
Thanks a lot!
EDIT: Forgot to post my system specs
Mobo: P6N SLI Platinum
CPU: Intel Pentium D 930
RAM 2GB (1GB x2) Patriot DDR 667 (PC 5300)
GPU: eVGA nVidia GeForce 8800GT
PSU: Thermaltake 500W

I used that bios, but on my regular p6n sli and got it to work. here is my topic on it
https://forum-en.msi.com/index.php?topic=115998.0
Dont clear the bios after you take out the old cpu or it wont work
I have been tinkering with it all day just to see what the actual problem is and it doesnt seem that it is the EIST OR C1E. from what I have done it seems that it is a problem with the voltages that keeps it from booting. If you change those with the other cpu in and then save and exit. Dont let it reboot, shut it off before it starts to boot up again and put the e8400 in

Who has this setup - MSI P6N SLI Platinum & E8400

This message is intended for anyone who has the MSI P6N SLI Platinum & E8400 in a working state.
I've had the pleasure of perusing these forums for a while in hopes of finding an answer as to why my E8400 isn't working with my P6N SLI Platinum. I've updated my BIOS, I've RMA'd my chip, I've even contacted MSI support (with no reply I might add). I have been so careful when handling these components and thoroughly reading the instructions, to no avail. I've got the board and all components working with a different processor. I've tried the voltage modifications that many have said work, I've tried different memory, I even tried a different video card. So I'm stuck in the same boat as many it seems, however there are one or two posts on this forum and others where people have said they actually got it to work!
So now I really hope I can get this question answered - What is a working config? One of the things I haven't tried yet is a new power supply. My current PS is 650w, but has the 4 pin CPU power connector. From the posts I've read, it shouldn't matter if I have the 4 or the 8. But in reality, does this CPU work on the P6N Plat with an 8 pin connector? I'd be willing to go buy a new PS if thats the case! What else could possibly be the issue? Any and all feedback is appreciated. i really didn't want to start up another thread for this proc/board issue, but perhaps someone else has joined this board by now that may provide the little piece of info that I've been missing.
Cheers,
Aaron

according to the website, the 1.6 BIOS had cpu updates in march so I's assume it would have support for the E8400.
What exactly happens when you turn on the system with the E8400?
-=Mark=-

P6N SLI Platinum, audio driver update gives "No Driver was supported..."

I have the audio driver from the CD that came with the mobo, but I wanted to update it to the new version. Currently I have R1.67 2.32, I tried to install the driver (R1.83 2.51) from http://global.msi.com.tw/index.php?func=downloaddetail&type=driver&maincat_no=1&prod_no=1140 but get the message "No Driver was supported in this driver package".
Also, I went to the Realtek site and got their even newer driver R1.84 but it asked me to remove the previous driver first, I'd rather check with the boards first to see what is going on.
P6N SLI Platinum
BIOS 1.4
Realtek Audio onboard

Could you please point me to where I can locate Live BIOS, first I hear of it. Thanks for the input btw.
Another off topic question. Does the Dual Core Center work ok with Vista x64? Wondering just in case before I get to using it. On my first Vista install is seemed to work, 2nd format it would come up with 2 error messages and not start:
"Error! unable to load ntuneoem.dll" and "Failed to load overclocking driver! This program must run as an administrator."
I have ntune installed on my 2nd format (which I found out doesn't work in Vista 64 properly) but cannot uninstall it from Add/Remove. A wizard window comes up and closes in the same seconds when I click uninstall. Tried to uninstall using the MSI CD which with I loaded it, still gives an error (tried to google the error msg but the msg is extremely rare and doesn't point to the problem). Going to have to manually remove it it seems and hope I get it all.

P6n sli platinum + e4300 oc

I've read tons of posts on forums, but most just give FSB speeds, not actual numbers to use in setting the system clock, so how do we know what to use actually?
When do you use the 1:1 ratio? or any of the others if your motherboard BIOS doesn't let you manually set your memory multiplier?
I have the updated BIOS from MSI LiveUpdater and Web
I've Disabled the following in BIOS
Execute Bit Disable
Set Limit CPUID MaxVal to 3
HPET
CPU Smart FAN Target
D.O.T. Control
Intel EIST
All Spread Spectrum including:
CPU Spread Spectrum
PCIE Spread Spectrum
CPU/LDT Spread Spectrum
SATA Spread Spectrum
Questions
System Clock-Auto,Linked,Manual
Which is best and when to use for what?
I went to 1333 for a steady 3.0ghz overclock. Temps were below 40C
at idle and were 65C under full load.
Adjust CPU Ratio-To what?
Stock shows 9, but can go from 6-9 as well.
Last night I got to FSB1600
Mem 800
with 8x multiplier
very fast, but lost settings on re-boot. So basically unstable.
CPU Voltage-Try to not increase this by first overclocking as much as I
can on stock voltage, but if it becomes unstable or won't boot, I just increase it how I see fit based on stability right? I just want a good bootable computer to use daily for about 3 hours and 48hrs on weekends.
Not too much into games yet, but will once I get speakers and a better monitor. Mostly business/student needs.
Memory Voltage-Stock is: Timing 5-5-5-15
Voltage 1.8 - 2.0
I got this to 2.2 and everything was fine.
I can manually set it to 4-4-4-12 1T as well.
NB Voltage-I got this as high as I could and it worked great, I think it was 1.7.I heard on forums that the higher you go the better for overclocking. Plus it's got a fan on it stock and I don't care about noise fan at all.
SB Voltage-I got this to 1.6 and it was fine too. But it's not cooled so how much is too much?
FSB VTT Voltage-I read that if you go to 20% it stabilizes your rig when
you overclock, so I set it and it worked great.
My Setup
Intel Core 2 Duo E4300 Allendale 1.8GHz
ZALMAN CNPS9500 LED 92mm 2 Ball Cooling Fan with Heatsink
Arctic Silver 5 Thermal Compound
MSI P6N SLI Platinum 650i
G.SKILL 2GB (2 x 1GB) DDR2 800 (PC2 6400) Dual Channel
COOLER MASTER Centurion 5 CAC-T05 Case
Thermaltake TR2 ATX 430W
EVGA GeForce 8600GT 256MB GDDR3 PCI Express x16 Video Card
Western Digital Caviar SE 160GB 7200 RPM SATA 3.0Gb
$700 exactly with shipping from NEWEGG
PURE BUDGET BUILD

Hello welcome to the forum,
Quote
System Clock-Auto,Linked,Manual
Which is best and when to use for what?
I went to 1333 for a steady 3.0ghz overclock. Temps were below 40C
at idle and were 65C under full load.
System clock I believe is how the memory freq is generated. "Auto" would be automatic, "Linked" would be linked to FSB speed, "Manual" wold be manually setting the speed.
65c on the cores or the CPU? Because if it's the cores, drop down, anywhere over 60c and your CPU may start skipping cycles.
Quote
Adjust CPU Ratio-To what?
Stock shows 9, but can go from 6-9 as well.
Last night I got to FSB1600
Mem 800
with 8x multiplier
very fast, but lost settings on re-boot. So basically unstable.
CPU ratio is the multiplier in which you times the FSB speed to generate/set the CPU clock. E.g:
Code: [Select]
FSB of 100x10 (cpu ratio) = 1000MHz CPU core speed.
Quote
CPU Voltage-Try to not increase this by first overclocking as much as I
can on stock voltage, but if it becomes unstable or won't boot, I just increase it how I see fit based on stability right? I just want a good bootable computer to use daily for about 3 hours and 48hrs on weekends.
Not too much into games yet, but will once I get speakers and a better monitor. Mostly business/student needs.
yes only increase for stability, never increase because you think you may need too.
Quote
Memory Voltage-Stock is: Timing 5-5-5-15
Voltage 1.8 - 2.0
I got this to 2.2 and everything was fine.
I can manually set it to 4-4-4-12 1T as well.
They are fine, just don't go over 2.3v, your RAM chips will start to fry otherwise.
Quote
NB Voltage-I got this as high as I could and it worked great, I think it was 1.7.I heard on forums that the higher you go the better for overclocking. Plus it's got a fan on it stock and I don't care about noise fan at all.
No, wrong way to do it. Do it like CPU VCore, only increase when stability is needed. Also monitor temperatures of NB as much as your CPU. Fan speeds don't bother me either, but temps do! Watch them at all times when overclocking.
Quote
SB Voltage-I got this to 1.6 and it was fine too. But it's not cooled so how much is too much?
Only increase if you need to, the SB core is usually the last voltage that needs increasing.
Quote
FSB VTT Voltage-I read that if you go to 20% it stabilizes your rig when
you overclock, so I set it and it worked great.
It's the voltage you supply to the FSB bus, too much and you will kill the FSB and your mainboard will be a fancy paper weight. Only increase when stability is needed, just like every other voltage.

P6n sli platinum cannot boot up

Hello
Everytime I boot up the D bracket suggests the computer is failing on initializing the floppy drive controller. i have changed the cable, and changed the floppy drive but same effect.
In the BIOS, if I go through and F10 for no save and exit, it then exits to bank screen as it fails at the point above. If i make any changes in the BIOS, and then try to accept those changes it freezes on pressing either Y or enter. At that point all I can do is turn off and start again. Naturally it doen't retain those changes. I have done this several times to disable the floppy.
I have removed the battery and put it back, (It's 16 months old). It then did allow me to disable floppy but still machine did not go beyond the above point. Whenever I have tried to go back into the Bios again, it will now freeze when I try and accept any change in settings.
As you will see I am unable to even boot from a floppy at this point so cannot een consider updating the BIOS. However before yesterday it has been working perfectly.
Any suggestions, or the loan of an axe to reprogramme the ****** thing would be much appriecated.
Thank you
Malcolm
Motherboard P6N SLI Platinum, G52-73501x1-Q05
2.20.0050.10 BIOS verison
Intel Core 2 Duo Processor
Sony MPF920 floppy
4 Harddrives. Boot is IDE, then 3 others, one of which is sata
2 memory sticks, 2 gb ram
Plexwriter CD
Pioneer DVDRW 105
Pioneer DVD
DMX-6fire soundcard
HD620W power supply
full details not known as mostly stored on the computer
No faults on system since it was built 16 months ago

Quote from: yokochanie on 03-October-08, 13:55:28
Motherboard P6N SLI Platinum, G52-73501x1-Q05
2.20.0050.10 BIOS verison
Intel Core 2 Duo Processor
Sony MPF920 floppy
4 Harddrives. Boot is IDE, then 3 others, one of which is sata
2 memory sticks, 2 gb ram
Plexwriter CD
Pioneer DVDRW 105
Pioneer DVD
DMX-6fire soundcard
HD620W power supply
full details not known as mostly stored on the computer
No faults on system since it was built 16 months ago
"2 memory sticks, 2 gb ram"
That doesn't talk much, we need full details about it.
"Intel Core 2 Duo Processor"
Which one?
"2.20.0050.10 BIOS verison"
That's not your BIOS version, look here how to check==> https://forum-en.msi.com/index.php?topic=113146.0
What VGA you use?
Remove power cord from the PSU and leave just one memory stick in 1st DIMM, once done proceed with >>Clear CMOS Guide<<
Then try to boot, if no change disconnect any storages{4 HDD's, 3 Optical drives, and any USB devices which you may have attached} and re-test.

P6N SLI Platinum - E4300 multiplier drops to 6x

Hi all, first post. Did some searches on here and can't find an answer, also this is a pretty new mobo.
CPU-Z shows my cpu at 1.8ghz @ 9x multiplier, but every few seconds it switches to 1.2ghz @ 6x multiplier. This sounds like a speedstep issue, but I disabled EIST in the BIOS, and all spread spectrum options. In windows power management I set it to Always On. I see a lot of talk about C1E but don't see any option regarding that setting in my BIOS.
Is this normal behavior for the E4300? I'm hesitant to start OC'ing when I'm having issues at stock clock.
Thanks for any ideas.
My setup:
P6N SLI Platinum / E4300 / Scythe Ninja / Antec Trio 650 / 2x1 GB Corsair XMS2 6400 / 2x WD 160gb - RAID 0 / Leadtek 8800gts 640

Quote from: Maesus on 06-March-07, 09:06:11
how about locking it to 6x and ramp up the FSB much higher?
Would there be an advantage to that versus a 333fsb x9 (3ghz) OC? I didn't get the best ram in the world because I wasn't looking for crazy speeds. The PC-6400 Corsair ($160 w/rebate) I have is rated at 5-5-5-18 at 1.8v. I have it at 5-5-5-12-2T at 1.9v. I'm not uber-conversant on memory timings but when I set it on 1T windows crashed immediately. Anandtech mentioned that changing to 1T had little to no real world performance improvements so I can live with it.
Currently I have the fsb at 333 (1333 in BIOS setting) and DRAM at 333 (666 in BIOS) so I have a 1:1 ratio which I understand is preferable. The MSI Dual Core utility reports that my CPU is running about 7 degrees cooler than the System temperature. Is that possible, or do I have a jumper setting mixed up somewhere...

P6N Sli Platinum E6600 Bios version ?

Hi.
I have the P6n Sli Platinum, I used the Live Update tool to upgrade my Bios.
The Bios it upgraded to is version 1.7 but on the Cpu support page E6600 should use the 1.4 Bios ?
After the upgrade my computer became slow and started to stall on me and about 1 hour later my video card died.
I have tried another video card and the motherboard works fine.
I'm just wondering if version 1.7 should not be used with E6600 ?
If not, why ?
And could the bios upgrade kill my video card ?
I know it sound weird but I wanted to check...
Thanks.

Quote
The Bios it upgraded to is version 1.7 but on the Cpu support page E6600 should use the 1.4 Bios ?
No, you are reading it the wrong way: What the CPU Support list is trying to tell you is that you need at least BIOS Version 1.4 to ensure that the E6600 is fully supported. Using v1.5, v1.6 or v1.7 with an E6600 is no problem.
Quote
I'm just wondering if version 1.7 should not be used with E6600 ?
It is totally okay to use that BIOS Version with the E6600.
Quote
and about 1 hour later my video card died.
That has nothing to do with the processor & BIOS Version. It was probably just a coincidence.
Quote
And could the bios upgrade kill my video card ?
That is very unlikely.
Quote
I used the Live Update tool to upgrade my Bios.
Please try to avoid MSI Live Update (or any other Windows based BIOS Flashing Application) in the future. Windows based BIOS Updates are very risky. >>Use the MSI HQ Forum USB flasher<< instead, if a BIOS Update should every be necessary again.

P6N Sli Platinum event viewer error

On my new P6N Sli Platinum mainboard, every time I boot up I get the following error in the event viewer log:
"The ForceWare IP service service failed to start due to the following error:
The system cannot find the path specified. "
I think this has to do with Nvidia network drivers. The network seems to work ok, although I have by default two network controlelrs: one labelled "1394 Net Adapter" and another "NVIDIA nForce Networking Controller". Which of these that handles the actual connection seems to change randomly, but it doesn't seem to affect the performance.
I'm running Windows XP Pro SP2 with all the updates from winupdate.
Does anyone else have the same issue?

Quote from: Isandhlwana on 20-April-07, 21:51:28
On my new P6N Sli Platinum mainboard, every time I boot up I get the following error in the event viewer log:
"The ForceWare IP service service failed to start due to the following error:
The system cannot find the path specified. "
I still get this error in event viewer each time I start up. I went to administrative tools->services and tried to enable the Forceware IP Service manually: system cannot find the path specified. The path box in the service properties is empty.
After googling I found that the service corresponds to the following executable: nsvcip.exe. This file is not found in my system. Is this normal? Does anyone else of you have this file?
Apart from the error message in event viewer my system is functioning perfectly.

P6N SLI Platinum mobo with hard drive/sata crashes

i've experienced a (now recurring) problem with my hardware over the past several months. i've come home from work twice now, once about 2 months ago, the other just today to find my computer stuck at the windows xp loading screen. if i tried to reboot the system, it would hang at that point, until i disconnected the offending drive/sata channel (i had 3 hard drives in my system, 1 150gb drive with operating system, ect, and 2 500gb drives for storage (mp3s, video, ect). i've narrowed the problem down to either the motherboard or the sata cables (i don't have spare cables to test with), as the hard drives work perfectly in an external usb enclosure. any ideas of what could be wrong?
basic system stats:
msi P6N SLI platinum motherboard
intel core 2 duo E6600 2.4ghz processor
crucial ballistix DDR2 800 (PC2 6400) 2 gb SDRAM
EVGA GeForce 8800 GTS video card
western digital raptor 150gb 10k rpm SATA hard drive
western digital caviar 500gb 7200 rpm SATA hard drive
PC Power and Cooling Silencer 750w power supply

in brief,
1- if you have one memory it should be in slot 1, closest to cpu, if two X 1Gb then they should be in one and three.
2- do you know what is virtual memory if so have you made adjustment or not.
3- you have freeze due to wrong bios setting till we get a good picture of your bios difficult to pin point the mistake, so use either a digi cam or web cam and take shoots of your bios then we can pin point the mistakes

P6n sli platinum NB fan -included or not

hello all
First post
-been viewing the site for ocing tips and such, currently running my p6n sli platinum with a e4300 @ 2.8ghz on stock colling and stock voltage, thanks to all that posted about bios settings etc. But thats neither here nor there.
But heres my problem:
So i didnt get a NB fan in my mobo box.. but a google on p6n sli platinum northbridge fan hits TONS of resellers and reviews of the board all saying its in there.
*and by tons i mean almost every result for pages..
so i called msi and they told me they dont make one.. then they said they make it for other boards and it fits this one, but it doesnt come with the board.. then they told me they did make them but dont stock them.. then they told me its an optional item and it can be ordered for 7$ plus shipping. So i told them that all the review sites and resellers say its there and they just said, no, its option and its 7$ plus shipping and that is their "final answer".
So... Did everyone get a fan or not? i realy want to know whats going on, newegg states that its part of the accessories, but since it doesnt list it as an accessory on msis official msicomputer.com site they tell me its not included and they know that its not because its not on the site. (for the record none of their boards list removable nb fans on the site and i know of a few that DO have it) I just want to see whats going on here.
So to all p6n sli platinum owners: Did you get a NB fan in your retail package?
Thanks

Quote from: ugzz on 09-June-07, 01:54:19
hello all
First post
-been viewing the site for ocing tips and such, currently running my p6n sli platinum with a e4300 @ 2.8ghz on stock colling and stock voltage, thanks to all that posted about bios settings etc. But thats neither here nor there.
But heres my problem:
So i didnt get a NB fan in my mobo box.. but a google on p6n sli platinum northbridge fan hits TONS of resellers and reviews of the board all saying its in there.
*and by tons i mean almost every result for pages..
so i called msi and they told me they dont make one.. then they said they make it for other boards and it fits this one, but it doesnt come with the board.. then they told me they did make them but dont stock them.. then they told me its an optional item and it can be ordered for 7$ plus shipping. So i told them that all the review sites and resellers say its there and they just said, no, its option and its 7$ plus shipping and that is their "final answer".
So... Did everyone get a fan or not? i realy want to know whats going on, newegg states that its part of the accessories, but since it doesnt list it as an accessory on msis official msicomputer.com site they tell me its not included and they know that its not because its not on the site. (for the record none of their boards list removable nb fans on the site and i know of a few that DO have it) I just want to see whats going on here.
So to all p6n sli platinum owners: Did you get a NB fan in your retail package?
Thanks
Mine came with one. I used it for a day and yanked it. It is WAY too loud - like louder than my case fan, CPU fan and GPU fan combined. You'd have to be stone cold deaf for me to recommend this cooler. It really is that bad.

MSI P6N Sli Platinum won't Post with E8500

Ok, I've been pulling my hair out on this one off and on for a couple of weeks, and I figured I'd finally just post here and hope for some advice.
I recently bought a C2D E8500 CPU on newegg to replace the E6420 I currently have running in my system. The motherboard is a P6N SLI Platinum with the v1.7 Bios. The problem is that whenever I swap the E8500 in for the E6420 the computer powers on, fans start spinning, and then it just sits. No beeps, no lights, nothing. When I put the E6420 back in the whole thing boots up just fine. I've cleared the CMOS two different ways (removing the battery and hitting the CMOS reset button), and nothing seems to help. I have tested the CPU in another machine, and it works just fine. The MSI tech support has told me that the problem shouldn't be happening, and has suggested that I RMA the board to them. I'd rather not be without my computer for 3-4 weeks, so I figured I'd post here and see if anyone had any advice before I pull the whole system apart and send the MB in.
PSU is a 700W OCZ
Graphics Card is EVGA 9800GT 512MB
Ram is 4GB AData
Let me know if anyone sees any obvious problems.
Tim

I please have a look here:
https://forum-en.msi.com/index.php?topic=123486.msg932471#msg932471
Sending the board to MSI to be serviced is probably your only option to solve this.

P6N SLI Platinum Reboots on Cold Start

Similar Messages

Maybe you are looking for