P7N Diamond & P7N SLI Platinum & P7N SLI-FI

The main purpose of those Betas ===> Solved the Video Corruption and fix 9.5 CPU Ratio Multiplier for E8500.
P7N Diamond       ==>      A7510NMS.121 {06/06/2008} (V1.2B1) Attachment: P7N Diamond v121.rar
P7N SLI Platinum ==>       A7380NMS.124 {06/06/2008} (V1.2B4) Attachment: P7N SLI Platinum v124.rar
P7N SLI-FI         ==>        A7380NMS.211 {06/06/2008} (V2.1B1) Attachment: P7N SLI-FI v211.rar
*** Flashing either of these BIOS' are at your own risk. Do not complain if you end up with a paper weight! ***
Flashing the safe way:
Use Method 1 or Method 2, both will do the same job.
Use it at own risk.
Before you flash!!:
Make and ensure PC is stable before proceed, remove any OC if you have.
Flash it via DOS mode by booting from USB key, CD/DVD.

Quote
Noobish question - is clearing the CMOS absolutely necessary after a BIOS update?
Yes, it is recommended to clear CMOS with main A/C power cable removed from PSU.  There might be small changes in data structeres between BIOS Versions.  Not clearing CMOS and resetting BIOS settings after flashing can have unexpected side effects.
Quote
I'm not really comfortable poking around inside my case apart from swapping a graphics card or hooking up power cables.
You don't need to "poke around" anywhere.  You simple need to unplug the main A/C power cable from your PSU, which is outside the case, hit the power-on button to drain capacitors and then press the little button on the back panel of your board for a couple of seconds.  That means you don't even have to open your case to clear CMOS.
Quote
So again, would NOT clearing the CMOS jumper thingy prevent successful update/boot?
If you restart your system after clearing CMOS, the BIOS will display an error message and prompt you to reset your BIOS settings, that's it.  Nothing to be afraid of.  The only risk involved is the BIOS Update itself, not the CMOS Clear.

Similar Messages

  • MSI P6N SLI Platinum and SLI!

    Hello!
    This motherboard comes with that SLI switch Card (required to be inserted before SLI function works)
    Also how can I remove that card from its place?
    And in what manner do I have to insert that card to make SLI function work?
    Helpful replies will be appreciated...

    Pull the 2 metal levers at the sides sideways and the card will flip out - Turn it around (Theres 2 arrows saying "non sli mode" and "sli mode") Put the side that says "sli mode" facing the connector, press it down and the metal clips will click back into place.

  • K8N SLI Platinum with SLI + X-Fi + TV tuner card

    has anyone have the above mentioned working?
    currently have 1 X 7800gt and a digital tv card. im thinking of getting an x-fi card + another 7800gt
    it was a bitch to get the tv card working due to the silicon controller conflict. i can imagine how much bandwidth the x-fi and tv card would consume
    so anyone has those combination working, i would really like to know 
    thanks

    I can't tell you exactly what you are looking for, but for what you want to do, an SLI board is not the recommended setup.
    And you've pretty much illustrated what I've been saying for some time.
    That is why I have what I have in my signature, and the board sitting in a box on my shelf is a K8N Neo4 Platinum.
    There may be more Tv cards based on the PCI-e hitting the market in the future. But an SLI setup in conjuction with a nice PCI sound card, and a PCI Tv Tuner is going to be a pretty good challenge. It may work, but you may experience flaky behavior.
    If you do get this working, then let me know...

  • MSI K8N SLi Platinum nForce4 SLi , wrong bios?

    I just received this board and in the bios there are options for the silicone image controller and the marvell onboard lan, however this board doesn't have either  of them(despite the msi website showing the ports in the picture, as are several websites that sell it).   Has it been flashed with an incorrect bios? possibly from the factory or has it been used returned and sent out again?
    also having major issues installing windows, had a install working fine on asus sli board.  stuck this in with 2 new maxtor 200Gb dm10+'s, tried to install with those in a raid 0 with 3rd and 4th ports having a dm10+ 300GB 16mb drive and a dm9+ 120gb drive.   It pauses each time on the msi, and when i put the asus back in, at the 19mins left to go "installing start menu components" part of the win xp gui install section.  No idea whats causing it.  using drivers off floppy from drivers on the msi cd.

    All the SLI boards have the same id, 7100, and must be near enough the same to support a common bios.

  • P7N SLi Platinum - Network & (large) Hard Drive Issues

    Hello, everyone. I'm hoping someone can help me out here (though I suspect I'm screwed). Several nights ago, I was sitting at my machine playing some Tera when suddenly I got a blue screen. They've been a pretty rare occurrence for this system, but I realize that from time to time, they happen, so I wasn't all that concerned. I just rebooted and figured everything would be back to normal. Unfortunately, I was wrong. Windows (7 - 64bit) took a noticeably longer time to pull up the full desktop and I noticed an error condition on the network icon in the system tray.
    Naturally, I pulled up my network settings and Windows told me that I was on an "Unidentified Network" with "No network access." I figured it was possible that I'd nudged the cable or something, so I looked at it and noticed that, instead of a flashing green light on the Ethernet port, it was flashing orange (this board does normally flash green, right?). I changed ports on the switch and when that didn't help, I changed cables. Still nothing. I installed the latest nForce drivers and still nothing.
    That's about the time I noticed another problem. I pulled up Windows Explorer to look for something on my data drive (3TB Seagate) and after an inordinately long time, I realized that it wasn't going to come up. I rebooted again and went into the BIOS settings and, to my horror, discovered that the BIOS, which was showing the drive at its correct capacity before, was now showing it as 800GB.
    I have NO idea what happened. It's possible there was a power surge (there was a storm in the distance), but the only two things that are affected are the network and that one hard drive. I updated to the latest BIOS and that didn't help at all, either. So... any ideas? Or am I just going to have to track down a new MB?
    Thanks,
    Sam

    Far as I know, that board is not capable of properly supporting a HDD over 1TB?
    http://www.msi.com/product/mb/P7N-SLI-Platinum---P7N-Zilent.html#/?div=BIOS
    You can try a power off, PSU power cord pulled, battery removed, CMOS clear and settings reset.

  • MSI P7N SLI PLATINUM 750i Wont Power UP!!

    i have an MSI P7N SLI PLATINUM 750i which was working perfectly but one day it just wont power up for some reason. my configs are
    MSI P7N SLI PLATINUM 750i
    Core 2 Quad Q9550
    MSI Nvidia 8800 Ultra HD OC
    4 Gb DDR2
    1T WD HDD
    PSU 750W Cougar
    i have tried every thing clean the pc,changed every thing but it still wont power up i tried another board with the same configs and it powers up just to make sure the problem is in the MB The red light on the motherboard stays on thats means there is power running thorough the MB. it still under warranty but the problem is i can reach the MSI HQ here in egypt to fix it or change it so any ideas?

    well i have reported my issue to MSI Customer Support exactly like that:
    Quote
    i have an MSI P7N SLI Platinum / P7N Zilent which was working perfectly but one day it just wont power up for some reason. my configs are
    MSI P7N SLI Platinum / P7N Zilent
    Core 2 Quad Q9550
    MSI Nvidia 8800 Ultra HD OC
    4 Gb DDR2
    1T WD HDD
    PSU 750W Cougar
    when i press the power button nothing happens.its still under warranty but the problem is i can reach the MSI HQ here in Egypt to fix it or change it so please advice about the name and the location of the MSI HQ in Egypt and notify them about my situation and to contact me regarding my problem
    so do u think that they will replay and advise about the issue?

  • Bios mod for K8n Neo/4 Sli Platinum

    I have this motherboard, only the box is blue. I dont know if it is platinum or not, but it says platinum when it starts up.
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=641
    I want a bios mod that would allow me to go higher with my vcore. I can go to 1.55v now.
    I found this site but I cant figure out which to choose.
    http://forums.techpowerup.com/showthread.php?t=1960
    Here is a image of Cpu-z

    Quote from: pcharouz on 01-May-06, 10:51:23
    I am kind of confuzed too, this is what it says in my newegg history.
    MSI K8N Neo4/SLI Socket 939 NVIDIA nForce4 SLI ATX AMD Motherboard - Retail
    Item #: N82E16813130492
    MSI 626 913 0828  $123.00
    The only place it says platinum is the bios, there is no platinum on the box or board, is there a non platinum board?
    yes NVIDIA® nForce4 SLI based CHIPSET has a 4 models:
    K8N Diamond, K8N SLI Platinum, K8N SLI Series(K8N SLI-FI and K8N SLI-F)
    look here mobos table. also can compare:
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_list.php?kind=1&CHIP=68&NAME=Socket%20939%20(AMD%20K8)

  • P7N SLI Platinum Unstable with over 2GB ram and/or dual channel memory on.

    Hello need some help or to report something to MSI regarding blue screens, freezes when booting Vista 64 (SP1 + all fixes installed) with more then 2GB ram.  Single channel mode works (either 1 stick of 2 GB or 3 sticks of 2GB) and is rock stable.  Booting with 2 x 2 or 4 x 2 yields instability and blue screens. 
    I read over Microsoft's hotfix KB929777 however it appears this patch was applied during SP1. http://support.microsoft.com/kb/929777 - when I attempted to apply this hotfix I got the message this update does not apply to your system.
    Memory tested in other gaming system using 4 sticks of G.Skill 1066 DDR2 ram and still have the same issues.  Other forums like Evga.com, Tom's hardware and 411overkill.com tend to suggest some problem with this new bios version 2.0, written by Nvidia.  Some others mention possibly an Nvidia nforce driver issue. 
    Therefore, under duress during testing - with 1 stick or 3 sticks of ram, all tests perfect and passes all stability tests, good marks in Sandra, plays any game.  With 2 or 4 sticks of ram, very unstable won't stay up but for seconds. 
    Any ideas?  (Tested 7 ways until Sunday!)
    My other rig, rocks solid and stable with Vista 64....  It's the Evga new mainboard 780i with triple SLI (132-CK-NF78-A1), 8gb of Gskill 1066ddr2, MSI 8800GT (x2 sli mode) Q6600 @ 3.2 ghz - Raid 0 on dual WD caviar 640 gb/sata 3.0gb/sec.  Seasonic 700w p/s.  8gb of memory and not a hiccup.  Ram 2.0 volts, cpu @ 1.36v.  Will handle the memory from both systems with out fault. 
    Considering I can swap memory back and forth and confirm it's not the sticks, swap graphics boards (own 3 of them!) and rule out that....
    Fyi.  Any help is appreciated! 

    Dump question, but have you pickup the correct update e.g. for 64bit? ==> http://www.microsoft.com/downloads/details.aspx?FamilyId=91672C7C-614B-404C-850C-377541E93C18&displaylang=en
    "This comes inside SP1 for vista 64, as noted with my other system during the build. "
    Better double check it.
    Install all four memory sticks and do a memory check with >>Memtest86<< 1st, ensure that no error(s) will comes during testing.
    Also how about that?:
    Quote from: BOSSKILLER on 07-April-08, 23:55:36
    Remove your OC then see how its goes.
    "When the system boots in single channel mode (only 2 or 6gb of ram meaning 1 or 3 sticks installed into the 4 slots) its' rock stable.  When it boots into dual channel mode (2 x 2 sticks or 2 x 4 sticks) extemely unstable. "
    That means, timings are too tight, or they need a bit more vcore help, or some of the memory stick has failure.
    "MSI P7N SLI Platinum - MS-7380 - Bios 2.0 on Vista Ultimate 64-bit - all updated."
    That BIOS is not for your board, you should use 1.xx

  • Help with ram slots on MSI P7N SLI PLATINUM

    rig config:
    MSI P7N SLI PLATINUM (MS-7380)
    bios version: 1.3v
    Q6600 quard core 2.66GHz
    Zotac modded 9800GTX+ amped version
    2x2 Gb DDR2 800MHz Kingston
    500 watt (absolute) power supply (taken form an old HP workstation)
    windows 7 X64
    Everything's on stock setting
    Its been almost 1 & 1/2 years since i bought this rig, and from first month itself i have been having problem with the ram. The problem is not with the sticks, its with the ram slots. There are different things that happen. Sometimes when i boot my system:
    1) either, it wont start, i.e. no boot screen.
    2) It will load upto windows startup screen, crash and restart in an infinite loop.
    3) It will load windows, then crash after sometime.
    4) If i run any memory diagnostic, it will give errors.
    At these times, i take out my 2 ram sticks, tinker with them, place them in different combination of ram slots, try push them in, in a certain way, keep trying until it yields and it boots up again ( generally a process of 1/2 an hr to an hr). After this my system will work fine ( no errors on any memory diagnostic) and boot properly for a week or 2, maybe even a month, but then again the same problem happens. I know for sure that there is no problem with my dimms (have checked them in other system and they work fine), its something to do with ram slots, or memory bus-controller structure.
    Recently the problem happened again, though my tinkering didn't help. My system only boots up if i place any of the ram sticks in the 3rd slot (the 1st orange one). It wont work for any other slot and neither will it work if i place both of the sticks together. I have tried resetting my bios as well cmos settings, but it has not helped. My mb is still in warranty, but if i give it for repair, it will be gone for a good month or so, which doesn't go well with me. If someone has any suggestions, or a way out, it will be highly appreciated. Please help!

    Quote from: nellinil on 10-July-10, 10:27:51
    yes the psu has a single +12v rail with 21A rating, but somehow i don't feel the problem is because of it. When my system successfully boots, it works properly. I can play or work on high performance softwares for any number of hours without fail, which ought not to happen if the psu is bad.
    Hmm, you are ignoring the possibility that your PSU is "flaky" (that's a technical term)!!!! You've never had any gizmo where "sometimes it works and sometimes it doesn't work"?
    If you don't want to buy a new PSU then at least beg-borrow-steal another one and see if your symptoms change.

  • P7N SLI Platinum and power consumption?

    In few day I'll get a Msi P7N SLI platinum to replace my Gigabyte P35,I would like to know the power consumption for 750i? Is lower than 780i?
    You can see in the picture the 780i 48W and P35 only 16W So big different!!!

    A quick Google search pulled this article.  Not sure if it helps you any, but here you go...
    http://hothardware.com/Articles/NVIDIA_nForce_780i_SLI_Arrives/?page=11

  • Having a hard time OC'ing my Q6600 on the P7N SLI platinum!!

    Well, first of all, I am new here, so hello to you all guys! 
    I just purchased the p7n yesterday. I had a P6N SLi-V2 before and wasn't able to get over the 3.0 GHz (stable)! I thought the P7N will a much better overclocker but find myself having a really hard time get it over 3.0 GHz again!?
    Tried different versions of the bios (1.0,1.1,P04 and now 2.0) with no succes! Maybe anyone can help me out here and maybe share some bios setup? Will really appreciate it 
    My rig:
    Q6600 C2Q G0-stepping
    Tuniq Tower 120 CPU cooler
    P7N SLI Platinum
    1 x 2 GB TakeMS PC6400 DDR2 RAM
    2 x MSI NX8800GT OC 512MB
    1 x 200 GB + 1 x 250 GB HD
    Cooler Master Extreme Power 650w

    Quote from: troopertroop on 20-April-08, 22:22:09
    Man, this turns out  to be like a disaster :S:S I tried everything and now it won't even be stable @ 3.0 GHz with vcore 1.35, vram 2.2, fsb vtt 1.45, nb 1.4 and SB 1.5 (random reboots like crazy!). I have the intention to get some better OC's going from a p6n sli v2 to this board and it's even doing WORSE??????? The only weakpoint I can think about is my single stick 2GB TakeMS pc6400, but I never go over the stock speed of 800 MHz, so can that still be a bottleneck even at stock speed or even lower?
    Any help will be welcome...
    I found out the hard way.........if you are not running memory from the QVL  list with this mobo, you will have problems with it. I was running mine with team xtreem 3-3-3-8 microns and all I had was errors and corruption when I overclocked. I had to reformat and switch back to the performance bios and now running corsair dominators 3-4-3-9 and this is the first set that can run at 1200 mhz at 5-5-5-18 2T 2.2 v with the fsb at 1600. I 'm using an E8400. I have read that using non approved memory and this board will not overclock properly.  The only non approved memory that works in my system is geil ultra 8000's and these are the originals running D9GCT's. For stability you should try OCZ, Corsair, Mushkin, Buffalo, Kingston. I have also had problems with crucial ballistix as I've found most of there modules are in someway defective and or not compatible with MSI and have rma multiple sets. I have a previous post going from P6N FI to P7N and have listed all the  memory that I have tried on this board. OCZ and corsair work the best and geil can be used but will not oc past 1142 mhz with stability. I think after a few bios updates this board will be able to use more different types of memory without stability issues.

  • Problem with my p7n sli platinum

    Hello,
    i just bought the P7N SLI Platinum for my new system and use an old ATI X1800XT as my gpu.
    after finished installing all the hardware,then i tried to install a fesh copy of windows xp...
    the problem is, every time my computer tried to login into the windows.. a blue screen will appear..
    i suspect the problem is due to the x1800xt..therefore i tried to use it with my old intel motherboard but it can login into windows perfectly well..
    does anyone know what the cause of this problem? is it because i'm using ati card with nvidia chipset?
    please everyone help me!!

    Quote from: BOSSKILLER on 23-November-08, 21:04:26
    STOP: 0x0000001E
        * There is insufficient disk space on the drive on which you installed Windows.
        * There is an outdated or incompatible third-party driver (or drivers) installed on your computer -- for example a faulty video driver.
        * There are system BIOS incompatibilities.
    Finally, my system is now working perfectly but I'm still not sure what is the cause for all of this madness. 
    I didn't change any of the hardware or the drivers.
    I don't think this is because of the insufficient disk space because after many series of failure with this board, I have tried to install a fresh windows copy using the same hard drive with my previous motherboard and everything seems to be running smoothly...it could finish the installation process..and safely loading into windows...
    Then when I tried with this board again, still no improvement at all...i tried again..again...and again...until i was frustrated enough to made some random changes in the bios settings and FINALLY...it works!!..
    I have no idea what were the changes that I've made in the bios...maybe it was just my luck....but I do notice the change in my cpu vcore..before this, it was running at 3.0GHz with default vcore of 1.080v...but now, the default vcore has suddenly changed to 1.250v with the same frequency of 3.0Ghz...and I couldn't find any way to return the voltage back as before..is this normal? I thought E8400 with E0 stepping should have lower vcore...isn't it?

  • RAID 0 on my board (P7N SLI Platinum)

    Hi guys, I'm gonna be honest and admit I'm a beginner when it comes to these kinds of things.
    Now thats out of the way, I've got two drives of the same size, revision and manufacturer, so I wanted to set them up in RAID 0 for faster load times and such. Though I don't have any idea where to start with this..
    I have Vista 64bit Home Premium,
    MSI P7N SLI Platinum
    Q6600
    8800GT SLI
    2x 500gb SATA Seagate Barracuda 7200.11
    4gb of RAM
    I was wondering if it would be possible for someone to give me a simple, easy to follow step-by-step process for setting up a RAID 0 system. I need help with the BIOS settings, the drivers and where to get them, and anything else (intel matrix if needed??)
    The manual doesn't mention how to do it, well..if it does I dont understand it, also I couldn't find any help on google so I thought I would come to a place where people will know about these things.
    It's going to be for gaming and general windows use so I want to it to be as performance orientated as possible - I daren't try myself as I don't have the ability to fix it if I really mess it up  I will seriously appreciate it if you can help me!
    Thanks 

    here is how I did it:
    enter the bois by pressing del, then go to integrated peripherals then to on-chip ata devices. You will see there a setting called raid mode it is set to ide change that to raid mode. Now enable sata1 and sata 2 oh make sure u drives is on sata1 & 2 . now save and exit. As the pc boot up there will a option to press f10 to create the raid. once in the utility change the mode from mirror to stripping(raid 0) , at the bottom of the screen you will see 2 boxes one on the left hand side will have your drives in it now move to the drive with the arrow keys and move both to the right hand side once there press ctrl+x to create the raid or read at the bottom of the screen for the options.
    Once your is created load vista normally and then when it asks to what drive u want to install it will be blank remove the vista cd and insert your driver cd for vista. Now click on load then browser then navigate to E:\ChipSet\Nvidia\Vista64\C72+MCP55\IDE\WinVista64\sataraid and click ok a list of driver will appear select all and click next. After this u will be taken back to the screen where you will now see your hard drive click on it and install vista like normal
    Hope this was help full as i do it this way

  • MOVED: P7N SLI Platinum Virtualizaton?

    This topic has been moved to Intel Core Duo and Core 2 Duo based boards.
    https://forum-en.msi.com/index.php?topic=117307.0

    Quote from: AaronYuri on 31-May-08, 05:41:45
    Go to "Advanced Chipset Features" > "CPU Feature" > "Virtualization (Technology [not always there])" > Choose either enabled or disabled.
    Yes, on the P7N SLI Platinum Bios version v1.1 it isn't there, is there another way or is there an update planned?
    It is also not listed in the mainboard Bios manual.

  • MSI P7N SLI Platinum - no POST, how to use Floppy BIOS upgrade

    Component Summary:
    MOBO: MSI P7N SLI Platinum LGA 775 NVIDIA nForce 750i SLI ATX, BIOS ver 1.1 (A7380NMS V1.1 022508)
    MEM: CORSAIR XMS2 DHX 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400)
    CPU: Intel Core 2 Duo E8400 Wolfdale 3.0GHz 6MB L2 Cache LGA 775 65W, S-spec: SLB9J (E0)
    VGA: EVGA 512-P3-N878-AR GeForce 9800 GTX+ SSC Edition 512MB 256-bit GDDR3 PCI Express 2.0 x16 HDCP Ready SLI
    PSU: Thermaltake Purepower W0129RU 600 W ATX12V SLI Ready
    Same problem is occurring as outlined in the following threads:
    https://forum-en.msi.com/index.php?topic=119615.0
    https://forum-en.msi.com/index.php?topic=120513.0
    I've carried out the same out-of-box tests indicated in 119615.0 without success.
    Question:
    Is it possible to force the existing system to boot to the FDD where the BIOS upgrade (v 1.2) would be stored ready for use? If yes, kindly outline the necessary steps to be carried out and please point me to the correct BIOS upgrade link for this configuration. If all else fails, MOBO can be exchanged but if BIOS can be upgraded via this method, I prefer this approach. I don't have access to an alternative CPU, so that approach is far less than ideal. Thanks for your assistance.

    Is it possible to force the existing system to boot to the FDD where the BIOS upgrade (v 1.2) would be stored ready for use?
    Yes, in theory it is possible to try an AMI BIOS Recovery Flash. However, in case their are other problems that are not visible because of the current problem, it is rather risky.  If there is a memory problem or something similar that is currently undetected, the system may crash during flashing and your board will be rendered useless.
    Quote
    f yes, kindly outline the necessary steps
    What you need:
    - you need an internal floppy drive (properly connected to the board and 100% intact)
    - you need an empty & formated floppy disk (make sure you check it for errors before you use it)
    - you need a PS/2 Keyboard
    What you have to do:
    - download the latest BIOS-Archive file from here:
    http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=1373
    - extract the BIOS File (e.g. A7380NMS.120), rename it to AMIBOOT.ROM [not AMIBOOT.120.ROM] and copy it to the floppy disk
    - insert the prepared floppy disk into the floppy drive attached to the P7N SLI Platinum and Clear CMOS with main A/C power cable removed from PSU
    - start the system and hit CTRL + HOME to force the system into recovery mode
    If that does not work, try a different floppy drive & disk.  Don't complain is the system crashes during flashing if the recovery flash starts (system stability is your responsibility).
    If you can't get the recovery routine to start and read the AMIBOOT.ROM file from the floppy disk, you need to install a supported processor.

Maybe you are looking for