P8 Neo-V Motherboard wont boot....

HI just bought a MSI P8 Neo-V Motherboard with a Celeron processor on it. Problem is that it wont even boot... i tried changing powersupply, memory etc etc but still nothing... BUT it gives a beep errror...
LOL dont know how to say this but here goes...
2 very short beeps then a pause and then 8 short beeps
like this
it dosent say the error codes in the manual and i need help...

grrr ok... Sorry guys but i GOT IT WORKING!!!!
I changed the AGP grafic card ... from a 3d Labs Oxygen to a Matrox G400 ... hmm that hasent happened before... well ok.
thanx anyways...

Similar Messages

New Neo 4 Platinum Wont boot past WIN XP :(

Hi, Im hoping someone can help me, I just built my system, its
MSI K8N Neo4 Platinum
AMD 64 3200+ 939 0.09
2 x PC4000 Crucial Ballistix (running at 200mhz)
4 Lighted Fans, Lighted case,
DVD RW, CD ROM ,
Floppy with Multimedia,
XFX Geforce 6600GT 128mb
Antec Trupower 430w 26a on the 12V, 36A on the +5V and 28A on the +3.3V
Ok, Everything works fine, till WINDOWS boots up ... And it wont boot, before the windows XP loading screen, it stays black, and freezes.. now.. to me it seems like memory/ power supply issue. lowered timings, raised Memory to 2.8v (Crucial suggest this voltage for the ram) ... no go... now my power supply is a good power supply.. but its only 20pin, and the nforce 4 ultra (well MSI) is 24pins ATX 2.0.. mine is a standard ATX12V... its supposed to still work, but Ive had mixed bagss of peopel saying it worked for them, and others that said it didnt.. but with this power supply, shouldnt I have been fine.. PLEASE someone help me, this is eating me alive...

Oh man this sounds familiar., i'm having some of the same probs. I just redid the install of XP Pro sp2 cause i needed the nvidia raid drivers for the NCQ on the Seagate i got.
The first install went fine but i couldn't oc more then 220fsb with this Corsair pc4400, so
i was like ok let's just get everything running sweet and then play. So after i added the
printer a usb scanner and a usb memcard reader for the camera, it would just hang after the boot logo for xp then it would hang on the Platinum screen sometimes too.
So i played with the voltages which seemed to help for a little bit., i went 3.3%+ on the cpu, 1.5 on the north bridge, and 2.70 on the mem. So i reformatted and used the 6.39 chipset drivers and the latest vid drivers from the manufacturer and everything seemed ok. So i proceeded to add the printer, scanner and card reader again 1 at a time and it seems like it's after the mobo gets warmed up is when it hangs on booting XP after the bootscreen., Cpu temps are at 35C and this mobo in a Cooler Master Cavalier case runs kinda warm for me like at 36 - 37C (According to Cool n Quiet) after it gets all warmed up. So i'm kinda at a loss here too. I got the same psu as the first poster. Memtest 86 ran for 4hrs, with no errors, and Sandra burned in for a couple hours with no problems.
Oh and the mobo say's the bios is the 1.1 dated 1-12-2005
So i'm hoping it's a bois thing that will be resolved soon, or is it this psu. Seems like some other fellas have had no probs with lesser psu's. Oh and do those 20 to 24 pin adapters make a difference?

K9N Neo V3 wont boot at all and has constant green light

Hi guys, as you can see I'm new to the forum and new to PC building this is my second rig and not my favorite for some reason this motherboard just wont boot. when i push the start button the heatsink fan spins and the power led stays green but other than that there's no other activity
heres my specs
MSI K9N Neo V3
AMD Semphron 3000 am2
512mb NANYA PC2-4200
Tested with 250w and 300w psus
Ati radion graphics card Pci-e
200gb hd
note these parts are mostly testing items to test the board before i buy more expensive parts any help would be great

Quote from: Fredrik on 24-October-08, 05:20:56
You will barely, barely get by with a very good 300W PSU, but that needs to be very good. Any hardware changes or addings will render your system unusable. I would recommend you a Zalman unit of about 400 - 500 watts. ~80 - 100 $. So you can "develop" the system.
But your system seems to pass POST. Can you disconnect the hard disk, possible opticals (CD/DVD) and if you have any USB things, and try again, please. Make sure you got the required power cables connected!
Nanya memory is new to me. It wouldn't be a Dell special (memory)?
thanks for the reply im currently using a dell system but my new builds motherboard just wont boot at all thats the main problem the psus seem to boot other systems so im unsure to whether the board is healthy or not since i cant connect the cases original audio plug to this mobo :( its unable to give me beep commands and the green light as ive read else where often means something bad but the condition dosent seem to change even when i change out parts
and the psu is a 12v

P35 Neo FR wont boot with 1066 Ram

Hi Guys,
I have a problem with a new build. The specs are
P35 Neo FR
E8400 (not overclocked)
2 gb Crucial Balistax tracer 1066 Ram
XFX 7900GS card
450W PSU
It will boot and I have been into windows to which all seems fine, however I have an issue.
1. The BIOS and CPU-Z are showing my ram at 667. I have manually adjusted it to 5-5-5-15 and set the divider so it should be running 1066. However it wont boot and goes into the re-boot over and over and over and over and over again "mode". This can only be rectified by re-setting the CMOS and then it will boot with its origional 4-4-4-24 timing @ 667. I have checked the voltages and they make no difference. It will only boot when the LED's on both ram sticks are lighting up on first power up. Ram has been tested in another PC and doesnt seem an issue.
Bios is 1.5 I think. Should I flash and go to 1.8?
I will also try the Mobo, PSU, HD and GPU without anything else attatched to see if there is a problem
Also, 1 stick of ram at a time to see if thats causing an issue.
I would appreciate any suggestions
Thanks

Quote from: Jack the Newbie on 19-March-08, 22:28:13
Which FSB/Memory Ratio did you choose in BIOS?
Does it work, if you choose the divider for DDR2-800 MHz?
What is the memory voltage recommended for these modules @1066 MHz effective speed?
Did you try with one stick of RAM only?
Thanks for the quick reply
I think the divider was 1.1-6? I will confirm in a couple of hours once I am home. It works at 1-1 but the speed was 400mhz. It also ran at 667. Whatever that divider was.
I am going to try the one memory module test tonight and I will also report on that and the DDR800 settings.
http://www.crucial.com/uk/store/partspecs.aspx?IMODULE=BL2KIT12864AL1065 Is my ram and its rated at 2.2V
Thanks in advance and I will update in the next few hours.

MSI K8M Neo-V Motherboard - No Display on Boot

I have K8M Neo-V motherboard, when i power on my pc there is no display on monitor.
No error beeps comes on POST. Processor Fan is running properly.
I checked my Monitor and RAM, it working fine on other pc's.
what could be the problem? Plz any one can help me to solve this issue.
Thanks in Advance.

Quote from: Henry on 27-January-12, 13:37:49
Read the >> Posting Guide <<
Tell us what parts are in the PC. See my signature below for an example of information to provide.
Hi,
MSI K8M Neo-V (MS-7032-Ver:1)
BIOS: AMIBIOS SS53 (8758)
Processor: Athlon 64: 2800+
RAM: 1 GB - PC400
VIA® VT8237 Chipset
HDD- 80GB SATA Segate

Bigbang Xpower wont boot

Hi, First I'm sorry if my english is kinda bad.
I just installed motherboard, RAM and CPU because my previous PC wont boot either. The problem is the same.
When I turn it on my PC wont boot. Tried to disconnect all the harddrive, change the VGA, put only one RAM in first black slot, but the problem is still the same. The screen still blank.
I noticed the HD Led is off and I got error code 85 on the mobo.
thx before.

Quote from: Jack on 09-October-10, 01:34:51
That means that the initialization of the video adapter has already happened and there as no error during that procedure (CPU and memory are initialized even before video card initialization). Try a different monitor and/or monitor cable.
maybe I'll try with different DVI cable. Coz I just tried the monitor with Dsub cable to another computer and it's ON without a problem.

? i have a hp pavilion g6 laptop comes on wont boot 4 months old

? i have a hp pavilion g6 laptop comes on wont boot 4 months old wont boot to hd or cd can get to bios it dont help tryed to restore was not much on it .

Hi,
If it won't boot from the Hard Drive or Optical Drive, you may well have a fault with the Sata Controller on the Motherboard - at the end of the day, by far your best option as your notebook is still under warranty, is to contact HP and arrange for it to be repaired.
If you live in the US, contact HP Here.
If you are in another part of the world, start Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Toshiba satelite E45-B4200 wont boot up

Hi , I recently bought my Toshiba satelite E45-B4200. Unfortunately for last couple of days my system wont boot up. I dont think its a windows issue beacause i dont even see the toshiba logo which usually shows while booting up the system. When i power it on, The LED light around power button lights up for a second and then turns off autometically and nothing happens. Here is what i already tried : 1. Pressed the Power button for more than 30 Second while charging adopter was connected.( Power light indicator at the front blinked once)2. Tried pressing Power button for more than 30 Second disconnecting the power adopter. ( Power light indicator at the front blinked once)3. Removed battery and connected to power adopter only then tried booting up . Did not work as well . I was trying to access the RAM inside but it turns out there was no easy access. Can anyone help me out to reslove this please? Does anyone have a disassemble guide or a Video tutorial ? TIA

Sounds like you may have a short in the motherboard, you may also have a bad charger. If the battery is too low it can cause these symptoms. I would try to obtain another power supply and attempt to turn it on with it, If that fails I would send it in for repair.

Ram choice for K8T Neo FISR2 Motherboard

Can anyone tell me if this particular model of ram is compatible with the k8t neo fisr2 motherboard?
http://www.crucial.com/store/MPartspecs.Asp?mtbpoid=AC1B73A7A5CA7304&WSMD=MS%2D6702+%28K8T+Neo%2DFIS2R%29&WSPN=CT6464Z40B
according to crucial it is compatible with the mobo, but i don't see it on the msi vendor approved list for the mobo. I did purchase it, however for the new computer that i am building, comp powers up fine, but no signal is getting to my monitor. Do you think if the ram is not compatible and is not working, then the new machine won't boot properly, hence no signal to monitor?
i'm trying to rule out/in the memory ram as the culprit for my new comp's problems

Well first you have not posted your specs so it's a bit hard to determine if the problem could be somewhere else. Please add yoiur specs to your signature.
Second I am assuming that you don't have any other RAM you can try so here are a couple things to check;
Put in a single stick of RAM and see if it comes up, if not then try another stick.
Check and see what is happening on the D-Bracket LED's.
Double check to see that both the 4 and 20 pin power connections are plugged into the Motherboard and see if your video card requires power through a molex connector. If so make sure it has a power Supply line plugged in.
Reset the Bios with the onboard jumper. Caution, make sure you remove power before you do that step. You may also have to remove the RAM when you reset.

Pavillion zv5000 laptop wont boot from cd after mobo and hdd replace

So I inherited a dead zv5000 laptop with no hdd. I replaced the motherboard and CPU, and it powered up and booted from the cd drive with no hdd installed. I was able to run memtek and the original hp os recovery discs, with no hdd installed.
Then I put in an empty hdd. The bios sees the hdd ok, but I suddenly can't boot from the cd drive. The bios settings are correct, and the discs spin in the cd drive, but it wont boot with the recovery discs, memtek, or an original xp install disc.
When I remove the hdd, it still wont boot from the cd drive.
So I google and I read stuff about hp tattoos on hdds and motheboards and dmi, and no passwords for the average person to do the tattoo.
So what do I need to do ? I don't understand why it was good with the new motherboard, but as soon as I plugged in an hdd it wont do anyting. I cant update bios because I cant boot past the bios, and not sure how that would help anyway.

If you have an open firmware password, delete it. It will not boot off anything but HD with OF password. Or at least thats what it was for me.

975x wont boot - new parts

Hi all, im new to this forum but it seems great, i read around abit and found some useful posts.
However, i have the following setup :
Msi 975x
c2d 6400
2gb corsair xms 6400 c4 ( 2*1gb )
7900gs PoV
Aspire 550 psu
I just put the parts toghether again, after having the parts returned to vendor, he claims the first cpu didnt work, and returned the motherboard while i waited for a new cpu to arrive. When i got it i tried the system again, but the following error is still there ;
The system wont boot, other than the fans will spin up but no screen at all, just stands there, when i use the usb led thingy, it shows 4 red dots.
I saw some posts about OCZ memory that wont work, but those were reported as memory issues by the led if im correct, and as i can see it arent 4 red dots the code for CPU , or can the code be wrong and its still the memory ?
The new cpu i got was in an unopened box so it was really new, but i refuse to believe i have broken 2 cpus or have recieved 2 dead cpu from vendor.
Any ideas would be very much welcome.
Cheers // Baboon

Baboon,
You're not the only one surprised.
I bought THREE 975X PUEs and every time I have re-visited the MSI website I have found new caveats for something the board won't do, or for something that won't work, or for something not included . . . no fixes, mind you, just oddly worded "escape clauses".
Here are some examples:
MSI Reminds You...
• DDR2 800 needs to work with Intel Conroe CPU with FSB1066.
• The default memory frequency is DDR2 667, you can set to 800 in BIOS settings.
• Due to the BIOS limits, the Intel RAID and the JMicron RAID functions can not be enabled at the same time, which will cause the system unable to boot up.
• The RAID setup floppy disk is optional depending on the districts. You can download the files from the website to make the setup disk.
• To enhance IDE transfer speed, you may install JMicron IDE/SATA Driver. You may download the driver by clicking the "Driver" icon at the left side.
• The floppy disk cable will be optional.
Yep, the first one was a big surprise to a lot of us sticking in our P4s. Hello? Well, OK, maybe the "CPU Support Chart" should have been the "CPU Semi-Support Chart".
OK, I'll even give MSI the first one. But the third bullet! Now that one just flat makes me laugh!
Beta Board! MSI didn't design this Board, it just kinda "happened".

MOVED: HELP PC wont boot up after bios flash

This topic has been moved to Older MSI motherboards.
https://forum-en.msi.com/index.php?topic=184216.0

bump removed, >>Please read and comply with the Forum Rules.<<
Quote
I downloaded a newer version of the bios made a bootable usb and flashed the bios all went ok than i restarted the pc and now it wont boot and I clear my Cmos it didnt helped me .. Changed Ram slots alternatively .. didnt help
have you removed power cord from the PSU before do >>Clear CMOS Guide<< ?
Quote
MEM: 2gb RAM DD2
what memory stick exactly? brand, model
is it 1 memory stick or 2?

MSI p67a-gd53 (b3) Wont boot with ram in slot 1 and 3, or 2 and 4.

Hi i recently built my own system, with just one ram stick in it boots fine and everything.
When i try to put the other stick in slot for so that in runs dual channel it just wont boot, it turns on starts the fans up and then just goes off, and repeats this.
The ram i have is Corsair Vengeance Low Profile 4GB (2x2GB) DDR3 PC3-12800C9 1600MHz Dual Channel Kit.
It also doesnt work in slots 2 and 4, can anyone help me :(?
My setup is :
OCZ ZS Series 650W '80 Plus Bronze' Power Supply
Intel Core i5-2500K 3.30GHz (Sandybridge) Socket LGA1155 Processor - Retail
MSI P67A-GD53 Intel P67 (Socket 1155) DDR3 Motherboard
MSI ATI Radeon HD 6870 OC HAWK 1024MB
Corsair Vengeance Low Profile 4GB
Seagate Barracuda 500gb HD
Gets no beeps on boot with just one stick in, im really confused :s
All Help will be appreciated.

Both ram sticks worked in slot one and it would boot but I tried running a game and it froze each occasion, cud this be due to the ram being dual channel and only having one in? Or that the ram has the wrong settings.
I have returned the motherboard along with the ram to the shop i got it from for tests to see if the dimm slots had problems. Il let you guys know what they say.
Thanks for the advice, when I get it back il build it again and see if it runs fine, if not il try the things youve said.
Can anyone else shed any light on this? Any other things I may have to try?
Thx again

Over volted gtx 480 using MSI afterburner now it wont boot.

I have a gtx 480 that I set to 1213 volts under water cooling.I was under the impression that with low WC temps I would be fine. I was stupid enough to run furmark, ran fine for about 3 minutes then computer shut down. I think the voltage is hard locked into the card I have tried booting with a second card (SLI Mobo) but the entire pc simply wont boot if I have my 2 pcie power connectors plugged in. Fan spins up and pc posts if no power connectors are connected but even with a second card as primary windows does not detect the card. I have tried using a second PSU to power the card while primary PSU powers mainboard and PCIE bus but I get the same issue. Computer refuses to boot. Lights come on for about half and second then I need to unplug the power cable and switch off psu to get any sort of response from my pc. I wish I didn't set the voltage to 1.2 ect, I know this is my own fault, but is there anything I can do on my own end to fix this?

I'm pretty sure aware afterburner only changes the cards values when running the profile in Windows so it should have reset on reboot.
Can you try the card in another machine to determine if it's damaged?
Clear the motherboard CMOS too. >>Clear CMOS Guide<<

T60 wont boot ~ I NEED HELP ~

H'ok.. So I was going to try to fix my friends T60 but I'm worried this is kinda over my head..
She came to me and said the OS was currupt and asked me to install a new os onto her laptop..
I was only able to install anything when the built in Wireless card was disabled..
Whenever you enable the wireless card, windows wont boot (all versions) nor will Windows installer boot..
Linux will boot though with the wireless card enabled.. but wont see a wireless network.
I've checked the hard drive and the ram.. both are ok.
I tried swapping the wireless card, but that didn't fix the problem..
Could it be the motherboard?
I need help! PLEASE WILL SOMEONE HELP!
~Jonny B

Could you try doing a system update using an ethernet cable? What OS are you using?
ThinkVantage System Update here:
http://support.lenovo.com/en_US/downloads/detail.page?&LegacyDocID=MIGR-66956
Here is the link for the ThinkVantage Productivity Center download:
http://support.lenovo.com/en_US/downloads/detail.page?&LegacyDocID=MIGR-61378
Think link lists all of the available ThinkVantage Technology Tools for your T61:
http://support.lenovo.com/en_US/downloads/detail.page?LegacyDocID=MIGR-61432#productivity
Let us know if that helps.
Did you find a post awesome? A great response? Kudo them!
Did the post you read answer your question? Did someone help you figure out your problem? Hit Solution Provided and give that person a 'thank you' for helping you out!

P8 Neo-V Motherboard wont boot....

Similar Messages

Maybe you are looking for