P965 Neo-f - primary and secondary ide channel stops working after changing gpu

I just changed my graphic card from 4850 to 4870x2 and then my idd devices stopped working, and when I look in device manager the primary and secondary ide channel has a yellow exclamationmark over them. And the error msg is as follow: This device cannot find enough free resources that it can use. (Code 12)
And when I look on the tab resources the two I\O range tabs have a red cross like over them probably meaning there is something wrong. And in the column Conflicting devies list: Input/Output Range 01F0 - 01F7 not available.
Input/Output Range 03F6 - 03F6 not available.
What I have tried so far:
Updating the bios, looking for I\o range crashes and irq crashes, uinstalling and reintalling severals times. And when I change back to my old 4850 card the problems disappears straight away.
Any ideas?

Quote from: Crispin on 28-April-09, 20:15:49
Well reality says something different  :D
And a reinstall fixed the problem. I find this post very amusing.
Ill bet your graphics doesnt even use its full potential on that board.
Me thinks it severly limited by the board and the cpu and imo a waste of a good graphicscard/money.
Its better to use only 2 slots of mem because of the strain you put on your memorycontroller when using 4 slots.
When running " double dualchannel"  the memorycontroller can be overflooded when running too high mem.speeds, with errors and BSOD and crashes as a result.

Similar Messages

  • I have pluged a portable battery to the USB and my macbook pro stopped working after that, right before it shut down there was a message on the screen that said something like " USB device is withdrawing so much power, please disconnect and connect again?

    I have plugged a portable battery to the USB and my macbook pro stopped working after that, right before it shut down there was a message on the screen that said something like " USB device is withdrawing so much power, please disconnect and connect again?
    if the device I connected have caused this, shouldn't the macbook itself have some type of protection that should prevent this from happening.
    because when I took it to an apple certified maintenance shop, the guy said that now it could only run while connected to the power. it won't run on batteries. and that I have to change the motherboard.
    can I just replace the damaged part only, would apple consider this as a design issue and they could pay for it, or should I just buy a new motherboard for 800$.
    Help.

    BB1B2,
    The problem is in finding a tech shop that will/can do board level repairs on Macs. They are few. And I certainly wouldn't spend $800 on a new logic board - I would replace the computer if I had to pay that much!
    You could call around to a few repair shops and see if they feel competent to isolate the problem and do a board level repair - but I'm afraid, in the end, that your search will be futile.
    Sorry,
    Clinton

  • Send Link and Mail To are stop working after update to FF v.13 on WinXP

    Send Link and Mail To where stopped working after upgrade to FF13 on win XP. I'd appreciate any suggestions.
    Thank you in advance

    Can you check to see whether your mailto setting got changed?
    orange Firefox button ''or'' classic Tools menu > Options > Applications
    In the Search box above the list, type or paste '''mailto''' and pause while Firefox filters the list. On the right side, you can select your mail application. Unless it's missing. Are you able to establish the connection?

  • Help! The secondary click on my trackpad for right and left bottom corners stopped working after 10.9.3 update??

    MacBook Air 11" 2013...did the OSX update for 10.9.3 on 5/17/14 and my secondary click on my trackpad just stopped working. Checked the system preferences and tried the other corner found it doesn't work for either bottom corners for secondary clicking. It will pull up the secondary click menu when I have the "two finger tap" option selected, but I don't use that one at all, it's not a natural function for me.
    I tried doing a hard reset 3 times and that didn't do it. Then I reinstalled the combo update for 10.9.3 and that didn't work either....
    ... ..any ideas?? 
    -lost without a secondary clicker

    The full release of 10.9.3 is available from App Store now. You can re download the full version from your Purchase tab in App Store. After download there will be Install OSX Maverics in Applications folder. Before installing OSX on top of the one on your system, copy the a install aoSX Mavericks to your external drive or any location. You can copy it to Applications folder for reinstall after that if you want.
    The new download will be 10.9.3. Before doing so, please try to boot into safe boot, by holding shift key and power on. Try your secondary mouse click to see if it work. If it is the same, then it will be driver corruption, try reinstall will help.

  • Ovi and syncing with Outlook stopped working after...

    I recently upgraded to Ovi 2.2.1.23 and syncing of calendar and contacts stopped working.
    The reason seem to be that when I try to connect to Outlook from the sync menu, Ovi freezes.
    Everything was working fine before and I just upgraded Ovi, nothing else.
    Any idea what to do? Ive tried to uinstall and reinstall Ovi but no change.

    Gawd, how I love this Apple forum. At least microsoft has MVP's that come out and help others.
    I too have this problem and I have Gmail and all my notes in my Gmail (on iPhone or iTouch) are not synched only those on my iPhone or iTouch.
    The options i have for default account are:
    Accounts
    iPhone or iTouch
    Gmail
    I have notes in my Gmail. How do I get them to my iTunes?

  • I updated MUSE and now the anchors stop working after one click. Active state on the buttons are not working either. The vertical scroll also stops working. Is this a bug.

    I updated to Adobe Muse 2014 and now the anchors on my site stop working on the page after one click. Vertical scroll and active state on the buttons also do not work. Is this a bug?

    I am also dealing with an anchor that stopped working. I tried everything i can think of to make it work, but no luck so far. I hope to see a helpful response here. Thanks.

  • Navigation and other features suddenly stopped working after I upgraded to FF4.

    A day or two after I upgraded from FF 3.6 to FF4, all the ordinary navigation features stopped working. Backspace/alt-<, even the back and forward arrows, Crtl-R to reload a page, and the address field doesn't show the current URL unless I click the identify information icon. All very odd. None of the keyboard shortcuts work.
    My bookmark toolbar does not load automatically, although I guess that Vista is the source of that issue.

    Doing a downgrade is not anything I have done or feel comfortable with. Is there a clean procedure to accomplish this?

  • How do I get the on/off sliding toggles to work in settings and apps?  They stopped working after I upgraded to iO6.

    After updating to iO6 on my iPhone 4S, the sliding on/off toggles do not work.  For example, I can't get the phone out of Airplane Mode.  Or, I can't change settings in apps.  The slider will not work at all.  This is true in both settings and in apps.

    Have you got notifications muted ? Only notifications (including games) get muted, so the iPod and Videos apps, and headphones, still get sound.
    Depending on what you've got Settings > General > Use Side Switch To set to (mute or rotation lock), then you can mute notifications by the switch on the right hand side of the iPad, or via the taskbar : double-click the home button; slide from the left; and it's the icon far left; press home again to exit the taskbar. The function that isn't on the side switch is set via the taskbar instead : http://support.apple.com/kb/HT4085

  • JDBC and FTP sender channels stop polling

    Hi,
    We have a great volume of sender JDBC and FTP sender channels.
    For this reason there is nothing unusual to have temporary error connections.
    Several months ago, with an XI 3.0 system, sender channels recover its functionality  automatically when temporary error connection is solved.
    But now, he have migrate to a  PI 7.1 sytem, and in the same scenario and configuration,  sender channel stop polling after a temporary error . In cc monitor this channels remains in  green status and there were no signs of stopped interfaces.
    Timeouts are correctly defined and there is no difference between channel configuration in our Xi and PI system.
    How to solve this problem?
    Thanks, in advance.
    Carme.

    Thanks for your fast response, Stefan.
    After writing this post, i ask the same question to our basis team and  we are in the latest sp.
    ¿do you know if there is any note or can you provide me some additional information?
    I'm not able to find any note about this issue...
    Regards,
    Carme.

  • Help! SB Live! 5.1 driver problems - IDE controllers stop work

    Hi. I've owned my SB Li've! 5. card since 200 and it has worked perfectly until now. I had to recently reformat my harddri've, and i had lost my original driver cd-rom disk so i downloaded the SB Li've! 5. driver off this website. When i reformatted my HD everything worked fine until i installed the downloaded SB driver. When i installed the drivers & restarted my PC, my DVD-ROM and CD-writer stopped working completely. I went into Windows control panel Device Manager and the problem seems to be that my Primary and Secondary IDE Controllers aren't working. It says i need to "restart my computer for this device to work properly". Well, i've restarted my PC about a hundred times since then but its still screwed.
    I have several times even tried reformatting my harddri've and re-installing the drivers again, but the same problem keeps happening. I can install my graphics card drivers etc. in any order using my DVD-ROM, but the moment i install the SB Li've! drivers my DVD-Rom & CD-writer stops working. I have used my SB card in this same PC w/ virtually the EXACT same hardware & software setup (and Windows version) etc. since i bought my PC, so nothing has really changed.
    P.S. I am using Windows 98SE.

    I don't really see much link in IDE controller with the sound card. Have you try updating the mainboard chipset driver that's controlling the IDE controller.
    Jason

  • Photoshop CC 2014 stops working after less than 30 second and shuts down

    I have installed and uninstalled Photoshop CC 2014 three or four times via Creative Cloud and each time it stops working after less than thirty seconds and shuts down the program. I then installed a an older version of Photoshop CS5.1 from a CD and it works perfect. I also have Illustrator CC 2014 and Lightroom 5 installed from Creative Cloud and both work flawlessly. What can I do to get Photoshop CC 2014 working?

    You have not provided any system information or crash logs, so we can't really know.
    http://myleniumerrors.com/working-with-your-operating-systems-tools/
    Mylenium

  • Front and back cameras stopped working after IOS 8 update

    My front and back cameras both stopped working after i updated my phone to the IOS 8 software. Does anyone know why this would happen or any way of fixing it?

    Hi VictoriaViking,
    Not sure why your cameras stopped working with the update, or what the exact symptom is (black screen, no response...), but please check out the Camera troubleshooting section of this article.  (I know some don't apply to your issue.)
    iPhone: Hardware troubleshooting
    If the screen shows a closed lens or black image, force quit the Camera app.
    If you do not see the Camera app on the Home screen, try searching for it in Spotlight. If the camera does not show up in the search, check to make sure that Restrictions are not turned on by tappingSettings > General > Restrictions.
    Ensure the camera lens is clean and free from any obstructions. Use a microfiber polishing cloth to clean the lens.
    Cases can interfere with the camera and the flash. Try gently cleaning the lens with a clean dry cloth or removing the case if you see image or color-quality issues with photos.
    Try turning iPhone off and then back on.
    Tap to focus the camera on the subject. The image may pulse or briefly go in and out of focus as it adjusts.
    Try to remain steady while focusing:
    Still images: Remain steady while taking the picture. If you move too far in any direction, the camera automatically refocuses to the center.
    Note: If you take a picture with iPhone turned sideways, it is automatically saved in landscape orientation.
    Video: Adjust focus before you begin recording. You can also tap to readjust focus while recording. Exiting the Camera application while recording will stop recording and will save the video to the Camera Roll.
    Take care,
    Nubz

  • P965 NEO & SATA2 HDD detected as IDE

    I can't run my IDE DVD-RW drive in DMA mode, it seems to be a common problem with P965 NEO mainboard. At the moment I can live with it, I've tried different JMicron drivers without success. I use BIOS v1.5, maybe I should try the new v1.6.
    Recently I changed the HDD (Seagate Barracuda 7200.10 320Gb SATA2) to one of the Intel ICH8 SATA ports. It used to be connected to the JMicron SATA port and detected as a SCSI drive. Now it is detected as a IDE drive by both the BIOS and Windows xp device manager. There are 3 x Primary IDE Channel and 3 x Secondary IDE Channel in the device manager even though there's only 1 SATA2 HDD and 1 optical IDE drive connected. The HDD runs in UDMA5 mode but the DVD is still in PIO mode. Now the HDD S.M.A.R.T function works (it didn't work before when connected to JMicron SATA) so I would like to keep it this way.
    My question is how should the SATA2 drive be detected? I get around 135 Mb/s burst speed in HD Tach, does the "IDE mode" slow the disk down?

    Quote from: Stink-Foot on 05-January-07, 19:35:21
    I can't run my IDE DVD-RW drive in DMA mode, it seems to be a common problem with P965 NEO mainboard. At the moment I can live with it, I've tried different JMicron drivers without success. I use BIOS v1.5, maybe I should try the new v1.6.
    Yes you need bios 1.6 to fix the problem.

  • No Secondary IDE Channel

    Howdy,
    I purchased a KT7A Pro board.  Upon installing it I found that I could not get the secondary IDE channel to recognize my drives.
    I enabled it in the BIOS (Lateset) but nothing worked. I tried changing cables and jumpers & everything else that you could think of, but nothing worked. The primary channel would pick everything up just fine, but when I tried them on the secondary....zilch.
    Okay...Bad Motherboard I figured so I went and exchanged it. In the process of taking out my Athlon XP 1700, I would up damaging it, so now I'm really PO'd.
    Upon exchanging the board and getting a new 1700 chip you'd think that all was well....Nope, Nada.
    Same problem, Secondary Channel will not work on the board. I am really disappointed as I like the features of the board, I just want my secondary channel to work.
    I got a promise card and all the drives work great. They  consist of 2 80GB WD, a 32X10X24 CDRW and a 16X DVD. I'm running Win XP Pro with 1GB of RAM and I have a GeForce2 400MX with 64 MB .
    What can I do to get the secondary channel to work, or what other options do I have?
    Thanks

    I posted here at the end of January with the SAME problem.. I've got a K7T Turbo2, and the same thing is happening, the secondary IDE channel isn't picking anything up. I figured the board was defective, asked here AND asked an MSI tech through e-mail.  I took the board back to the store and had them order another one for me, but I'm still having the same problem..  
    I've tried every drive configuration under the sun, swapping cables, trying drives one by one, enabling and disabling random things that should have nothing do with the price of rice in china, but nothing.  Any clues would help, I can't keep taking boards back to the store.

  • Bad secondary ide channel?

    Windows kept blue screening when i installed a new k9n2 board - i finally tried swapping the primary and secondary cables (HD's are now on secondary channel and dvd is on primary channel). Now it runs fine except the dvd drive doesnt show in windows. The light stays green but there is no response. - I think the secondary channel is bad - Is there any way to test this?  ???

      except that the HDs are listed on the secondary ide and the burner is listed as primary ide
    (HD's are now on secondary channel and dvd is on primary channel)
     Is that why, did you change them back to try? 

Maybe you are looking for