P965 Platinum IDE devices not recognized

I posted about this in a related thread, but I wanted to make a quick note of it in its own topic.
I have a DVD player and a hard drive, both of them IDE, that aren't recognized by the bios on this board. Is there maybe a problem with the IDE socket?

Quote from: leekh on 04-December-06, 14:37:55
ok. just check the specs of your power supply. http://www.antec.com/specs/sl400_spe.html
its seems that 18A output from the +12V rail is way too low for your system, especially for that power hungry GPU in your system. Try to borrow a higher powered PSU, with a mininum of 28A output from the +12V rail and see whether the problem still persists.
good luck.
That's good info, though I kind of doubt it has anything to do with the IDE issue. I don't know much about the particulars of the amperage output on whichever rail for a system. My calculations for the wattage required by my system seemed to indicate that there was plenty enough of that to run my fairly spare and non-overclocked system with a bit of room left over.
I'm begining to suspect that the real issue is the usual JMicron crap, and that I'm going to have to get some SATA adapters for my IDE devices to get them into the Intel SATA ports on the board.

Similar Messages

I have an Iphone 5S and used to sync it to my computer in the past without any problem, but now I can't and appears the message "usb device not recognized", and the cable is good and so the USB port. Do you have any idea what's the problem?

I have an Iphone 5S and used to sync it to my computer in the past without any problem, but now I can't, and appears the message "usb device not recognized", and the cable is good and so the USB port. Do you have any idea what's the problem?

Try leaving it plugged in and then restart the computer.
If you are on Windows this link may help but it is a bit old.
http://www.technologynext.org/error-usb-device-not-recognized-how-to-fix/

My ipod touch gen 4 will not recovery after software update. have tried everything. device not recognized by itunes. any ideas?

my ipod touch gen 4 will not recovery after software update. have tried everything. device not recognized by itunes. any ideas?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

USB Device not recognized by windows

When I first plugged my iPod into my computer, it went through the whole recognizing new hardware thing. Installed the drivers, then said that the new device was ready to use. But then I get a message that says "Device malfunction, device not recognized by windows" or something to that effect. I only have 3 days to return this iPod...anyone have any ideas? Thanks.

I'm not very familiar with the Windows OS but try this tip I picked on the forum up a while back, hopefully it might help.
1. On the Start menu, click Control Panel.
2. Double-click the System icon.
3. Click the Hardware tab.
4. Click Device Manager.
5. Scroll down the list of devices to the Universal Serial Bus controllers
6. Click the plus icon next to the Universal Serial Bus controllers.
7. Double-click one of the indented USB Root Hub entries.
8. Click the Power Management tab.
9. Deselect the "Allow the computer to turn off this device to save power" option.
10. Click the OK button at the bottom of the window.
11. Restart the computer.

When I connect.. sometimes it says Device not recognized or malfunctioned!

Hi. When I connect my ipod to any microsoft device, sometimes my ipod doesnt connect. I cant charge it, or restore it as it behaves like a useless piece of plastic.. I get a yellow bubble 'Device not recognized or has malfunctioned'
This problem is bizarre! I cannot find anyone who actually has a solution for this problem! Apples standard answer is for me to reinstall my drivers or update itunes or windows. Done it. No solution yet.
My ipod works fine.... sometimes. Its a completely unpredictable problem. Ive googled this problem and so many ipod classic owners have asked.. solutions ive tried: the 5r's, updating drivers, It managed to connect once, but now it wont. My ipod normally works fine on my PC, XBOX, laptop and Mac.. but sometimes, unpredictably, it wont be recognized by anything apart from the mac. For a month it would not connect at all and I took it in to an Apple store where they told me it works fine. Its not my PC.. its up to date, and theres no reason why it doesnt work on my XBOX because some times it does.. last night it did, today its broken again, I suspect tomorrow it may work. This is SO frustrating!!
I have alot of experience in PC's and normally I can solve a problem by process of elimination, updating and reinstalling, but in this case.. everything seems fine. My only idea is that maybe its my Sync cable?? Which also makes no sense because it generally connects fine on the mac - and, why would a sync cable be unpredictable.. surely it either works or it doesnt. HELP PLEASE!!
Nick.
my email is: [email protected]
my serial for my 80g classic is 8K819CPKYMV and is under warranty until May 2009, i bought it in August this year.

there is a good chance that this can be related to bad contact in USB lead.. e.g not enough power from IPOD to PC so that pc cannot recognise it. Where I work I get alot of USB devices on pc's that are not recognised and most of the time it is the connection to the device that is not good enough because the flat end of the USB adapter has been gradually bent over time just slightly and now contact is not good. It can also be todo with drivers or If you are using it through a USB hub.
so if it is not working through USB hub try direct. also try in back of PC as these Ports or direct access to main board to pc and would be less trouble some if there was a voltage loss from mainboard in pc to front of unit.

IPod nano 3rd Gen 8G "Device Not Recognized" on 2 diffrent computers...

I have the latest versions of iTunes on both a Windows XP service pack 3 computer and Windows 7 Laptop. I've tried multiple cords but both computers tell me "device not recognized", I've uninstalled and reinstalled all drivers. Done a reset and Disk Mode reset on my iPod. Haven't droped it or damaged it in anyway since i've connected it sucessfully to my computer last time. Will charge on a wall charger, car charger and dock. Tried connecting friends iTouch and it was registered by Both computers.
And ideas on a fix other than the $100+ apple wants, I'll just got buy a new MP3.

- Try another cable
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
Did you do everything here:
iOS: Device not recognized in iTunes for Windows
Including
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
and for the computer in queston
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
different USB port?
Runs this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
- Make an appointment at the Genus Bar of an Apple store.
Apple Retail Store - Genius Bar

USB device not recognized - ipod video-help!!

when I connect my ipod video, I get a message "USB device not recognized", when I click, I get: "no drivers installed for this device". I have re-installed the ipod software, reset the ipod and re-installed itunes, just in case. I have been on this problem since Christmas. Any ideas at all, anybody?
dell Windows XP

I have this EXACT same problem. And my ports are definitely 2.0 USB. I've uninstalled and installed all the iPod, iTunes and Quicktime components at least 4 times. I've reset the iPod. I've read everything I can get my hands on... nuthin'... nada...
Can anyone help?

USB Device Not Recognized - is my iPod toast?

Got a new computer recently with Win XP. When I try to connect my iPod with a USB adapter I keep getting "USB Device not Recognized" and if I click that I get "Try reconnecting the device. If Windows still does not recognize it, replace the device."
I can connect other USB devices like my compact flash cards etc. The iPod was working on my old computer.
Any ideas??
Thanks in advance for any help!!!

I had a new ipod and windows wasnt recognizing it or giving me the message "new hardware found" and then telling me the drivers were missing... this is what I did and it fixed my problem.
1. go to www.driverguide.com and sign up (for free)
2. download usbstor.sys & usbstor.inf (and take note of where you download them to)
3. update drivers by selecting folder you downloaded the two files to
4. restart computer
5. open itunes and then connect ipod
good luck
-jackie

Windows won't recognize my iPod - USB device not recognized

This is really frustrating. So I got a 4gb iPod nano on Saturday, took it home, set it up and everything was going just fine, no worry's. About 4 hours later I went to adjust my songs and it would not come up in iTunes. A little pop-up box said that the "USB device not recognized - one of the USB devices attached to this computer has malfunctioned and windows does not recognize it." After owning my iPod for less than an afternoon, I now have an ipod that I can do nothing to including change the music, charge it, etc. It works normally otherwise, it just won't connect to my computer. I then plugged in my older 256mb usb stick, and the same message, it too does not get recognized by windows. So I then tried a brand new 1gb usb stick that I had and the same result, not recognized by windows. I updated my itunes to the latest one after purchasing my ipod (version 7.4.3.1) and have looked up everything that I can and tried everything I saw to try, but nothing, absolutely nothing, worked. However my usb mouse, usb joystick, and usb printer all still work, but my moniter that has four usb outlets on it causes the same message, if I plug in the cable that connects one usb on my computer to the four on my moniter, windows can not recognize it. When I look in my device manager at the "unknown device" under the usb controller list it says that there is not driver for it, however I know that the drivers are either on my computer or built into windows. Any help? Anybody have an idea about what to do? Is it something in my windows registry has changed because of the new itunes, etc.?

Now that I've had some sleep, I realise I didn't really provide information that may lead to some specific help. Here goes - when I first plugged in the ipod nano (8gb), It displayed the screen it was supposed to - I could see the lightning bolt through the battery icon and knew it was charging. The icon for the ipod also appeared in the left-hand listing in itunes (in the section that existed under Library, before the sections Store and Playlists). This section now does not appear (I can't remember the title of this section, but it might have been 'devices'). In fact, I'm pretty sure this problem started when I clicked on this icon - nothing happened and it disappeared - so did the display on the ipod, which is not just the apple. This means itunes has only Library, Store and Playlist in the left-hand colunm. While I accept that computers do not work on normal logic, this seems to me to indicate that the drivers are fine, the system is fine, my laptop is fine - its the ipod or the usb cord. This morning as I tried again, this time my laptop gave me the option to 'click on the balloon to solve the problem' - let me quote: "One of the USB devices attached to this computer has malfunctioned, and Windows does not recognise it. Try reconnecting the device. If Windows still does not recognise it, replace the device". Come on folks - one of you will surely know how to fix this (short of me taking the ipod back to the store to get my money back).

"USB Device Not Recognized" in Windows XP

Hello, When i plug my ipod touch into my laptop which has Windows XP, it comes up as USB Device Not Recognized. I have no idea what to do please HELP ME!!!!!!

http://support.apple.com/kb/TS1538
There have been some problems accessing pages on the Apple web site. If the hyperlink gives you a "We're sorry" message, try again.

Disk Image Won't Mount - Reason: Device Not Recognized

As I've searched the discussion forums, I've seen plenty of postings for "Disk Image Won't Mount" and for "Device Not Recognized" but not the way I'm seeing it on my laptop.
After a backup and restore, my mac will no longer mount any... and I mean any images. I have downloaded several security or software updates from different vendors and each .dmg file will not mount. I still have the .dmg files in hopes that after I get this problem solved, I'll be able to install them, but...
It always gives the same reason for not mounting and I'm at a loss on what to do next. I've run Software Update hoping it will be a quick fix, but have had no success.
Any suggestions?

I have a similar problem. Using FireWire disk mode, I put a disk image of my entire iBook onto my iMac as a back-up. (For an unrelated problem, Apple told me I needed to erase my iBook completely and do a clean install of the system.) Well, I screwed something up. I don't know what exactly--maybe I didn't "put away" the device correctly, but the next day when I flipped on my iMac, the disk image of my iBook was just gone, and not to be found anywhere. I finally succeeded in restoring the image using TechTool, which scanned the entire volume of the iMac for directory information. And it's all there, because the img file is more than 10GB. But when I double-click on it, I get the following error msg: "The following disk images failed to mount...reason--not recognized." I've checked the app it's supposed to open with, permissions, and run Disk Utility volume repair. No dice. Any ideas??? Did I mention that this is EVERYTHING I had on my iBook???

"Device Not Recognized" - but for only one of three iPods?

Hi-
I am hoping to get some help, as I am stumpted. Here are the symptoms:
1) I have been successfully syncing two Nanos and a Mini on the same XP machine for sometime
2) One of the Nanos now gets a "device not recognized" message upon connecting, while the other two iPods will still connect just fine.
3) I've tried charging it fully (and running it down), the five R's, putting it into disk mode (updater doesn't recognize it's attached so can't restore), and installing iTunes on another machine (other machine doesn't recognize it, either).
4) The problem Nano charges and plays just fine on its own.
Any ideas?
Thanks!

Try downloading and installing iPod Updater 2006-01-10 (the version previous to the 2006-03-23) and restoring your iPod with that.
http://www.apple.com/support/downloads/ipodupdater20060110.html
If your iPod encounters difficulties being recognized with this updater, put it into disk mode first:
http://docs.info.apple.com/article.html?artnum=93651
Keep us posted!
Best wishes,
CG

Vista message appears - USB Device not recognized

Hi,
I have been getting the error messages "USB device not recognized" from Windows Vista.
It keeps on repeating itself sporadically.
The problem is that I do not have any USB device attach or plug to my computer.
It happens to sometimes plugged my USB Flash key device to drop some documents on my hard drive but I immediately unplugged the device after the task is done.
I used to have a Lexmark 1290 printer plug to my computer but since it was not working fine on Vista I have decided to unplug it and delete the peripheral in my printer manager.
I have installed the latest Windows Vista Update, BIOS update, and all possible drivers but I still having the messages.
Does anyone have a idea of what could be my problem?
Thanks

hi aladino00,
try this:
- connect all of your usb-devices to the notebook (printer, usb-storage)
- use this devices once (print and copy some files)
- then use the "safe remove of hardware" in your system tray and use the dialog to remove the usb-devices
restart notebook (cold reboot) and test it...
maybe there is a registry key been written that causes this behaviour...
therefor the described routine should eliminate it and make your notebook akt correctly again...

TS1369 usb device not recognized

I can't get my Apple ipod to be recognized by my new computer. It says "usb device not recognized". Any ideas?

Try Here > http://support.apple.com/kb/TS1538

USB device not recognized - Strange problem.

Alright, so as of this this morning out of the blue iTunes will not recognize my 120gb iPod classic. Whenever I try to unplug it and plug it back in I get a pop up error that says "usb device not recognized." I've spent the better part of today googling that phrase and trying everything from the basic 5 Rs, (except for Restore because my PC wont recognize the ipod) to reinstalling my motherboard drivers for the usb ports. Ive tried the iPod in every last USB port on my machine and I still get the same error message.
The weird part is, every other USB device I own works like a charm in every USB port on this same machine, including an old 60 gig iPod video I have. I plug that sucker in and it immediately gets recognized in iTunes. At this point, one would draw the conclusion that there is probably something wrong with the usb port on the iPod classic, however the iPod immediately connects to my laptop as well as my Xbox 360 with no issue. I should mention that I am running Windows 7 Release Canditate, and the iPod has been working fine on this OS for months.
I even went as far as doing a system restore to an older restore point thinking that it was perhaps a Windows update issue. This of course did not work.
There has to be some sort of issue with how that particular iPod communicates with this particular machine and I can't put my finger on it. Its driving me insane. Short of reinstalling Windows, I have no idea what to do from this point forward. Any suggestions would be greatly appreciated.

Have you tried uninstalling, then reinstalling iTunes (rebooting between the uninstall and reinstall)? Perhaps the issue is a corrupt file within iTunes.

P965 Platinum IDE devices not recognized

Similar Messages

Maybe you are looking for