P965 Platinum memory latency settings problem

When I overclock the FSB of my P965 Platinum with C2D E6400, I get problems with the memory latecy settings. My memory is specified as 667MHz 5-5-5-15 2T, but when I enter these latencies in the bios, CPU-Z and Sandra both say I have 3-5-5-15 1T. Which is of course out of spec and gives system instability unless I raise the memory voltage quite a bit above spec.
So does anyone have an idea why this might be? Is it a bug of the bios (ver 1.3) or are CPU-Z and Sandra both mis-reporting the value? In the latter case, why can I get rid of the instability by raising ram voltage??
Thanks for any help
/Mattias
PS The disable speedspep switch in the bios dosn't seem to have any effect. The multiplier still switches down from 8 to 6 when the CPU is idle. Anyone elso who has the same problem?

The CAS Latency issue is known and it is possibly being addressed by MSI technicians. Please refer to this thread, CAS Latency is in the list of desired fixes for a new BIOS release. For the time being, switch memory timing to SPD instead of Manual in your BIOS and it should be set to CAS Latency 5...
Memory voltage: at certain settings memory chips require a certain amount of power. The default voltage for DDR2 is 1.9v, so in other words DDR2-667 5-5-5-15 is the best your memory chips can do at the default DDR2 voltage, that's why your memory is rated as it is. Raising the voltage enables you to run above rated speed, you simply let the memory chips use more power. There are limits of course...
Disable Speedstep: please refer to this thread, should help you disable Speedstep.
 

Similar Messages

  • P965 Platinum - memory troubles

    I completed the following system over the weekend:
    P965 Platinum w/ 1.2 BIOS
    Core 2 Duo E6400
    Corsair Twin 2GB 800MHz 4-4-4-12
    Rosewill 550w PSU
    eVGA 7600GT
    I checked the BIOS and verified that the memory is recognized as 800MHz.  However, it is currently running at 5-5-5-18 timings at 1.9v.  I am able to change the timings to 4-4-4-12, but then the system does not boot (stuck on extended memory test).
    I checked with Corsair, and their documentation states that the 4-4-4-12 timings are achieved at 2.1v.  Unfortunately, the BIOS will not allow me to change the memory voltage.  The number is grayed out.
    How can I fix this?  I installed Duo Core Center to try to adjust it from there, but it will not run...I get the "This application has caused an error and must be closed..." message when I try to start it.  I reinstalled it with the same problem both times.

    First of all, Run a memtest86 session for each memory stick seperately , one of the sticks may be broken ... you never know...
    Quote from: EricT on 20-December-06, 11:08:30
    OK, I adjusted the voltage to 2.1v.  Then I disabled SPD and set the timings to 4-4-4-12.  I rebooted, and it crashed while loading windows.
    Try a little more voltage if the bios allows you to, 2.2 or 2.3Volt - It IS a budget motherboard, and budget boards tend to give less real voltage then what you selected.
    Quote from: EricT on 20-December-06, 11:08:30
    I went back to the BIOS and enabled SPD, leaving the voltage at 2.1V, and CPU-Z is showing the timings as 5-5-5-18 like before.  Frequency 400MHz, 2:3 ratio.  It is also reporting Channels # Single.  This should be dual-channel memory right?
    The SPD tab in CPU-Z tells me that each module has 400 MHz frequency with timings 4-4-4-12.  Now I'm confused.
    Might have something to do with having both sticks in single channel - Since there are 2 memory sticks in one channel it might automatically loosen timings for that channel...
    Quote from: EricT on 20-December-06, 11:08:30
    Another thing, if I put modules in slots 1 and 3, the system hangs at memory initialization.  I can only get it to run if I use slots 1 and 2.  I believe this is why I'm in single channel mode?
    Yes...
    Quote from: EricT on 20-December-06, 11:08:30
    Can someone help me get this memory running optimally?  I spent the extra money to get CAS 4 memory, but apparently I am not getting that performance.
    Core 2 Does not really benefit all that much from tight timings, you are confusing with athlon64 wich like tight timings ...
    http://www.madshrimps.be/?action=getarticle&articID=472 This article shows that core2 does not really benefit a lot from expensive high end memory.

  • P965 Platinum + E6850...problem

    Hi, i need some help. Just got some new computer parts.
    -Corsair 520W
    -Intel E6850
    -1x320GB
    My Current/Old system
    -P965 Platinum BIOS 1.5
    -Intel E6400
    -2x320GB
    -8800GTS
    -Corsair PC5400
    The problem is that i cant get the E6850 to work, When i start the pc it just keeps restarting all the time and i don´t see anything on the screen, just black. Right now I'm sitting on the E6400 which works.
    In the CPU support list, it says that the E6850 is supported buy my MOBO.
    Check here....
    http://global.msi.com.tw/index.php?func=prodcpusupport&prod_no=266&maincat_no=1&cat2_no=170&cat3_no=#menu
    And i have flashed the bios to 1.5.
    And if you take a look here on the BIOS data base for P965, The version 1.4 supports Intels Exxx series and 1333Fsb. And suppose bios 1.5 should support Fsb 1333...
    http://global.msi.com.tw/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=266
    So ? help please 

    Hi
    Well after looking on the forums with the same problem but with the E6750 and am now getting really worried.
    Back to the drawing board: I have Bios 1.4 installed
    1. Set the cpu speed default
    2. Set the Ram speed to the default of the Corsair Ram 6400
    3. Disabled Spread Spectrum
    Hey presto the system booted.....did a bit of overclocking OK, booted again .
    Upgraded to Bios to 1.5, system would not boot till I did the same again.
    So to me it looks as if its fussy with the ram settings, anyway have a go!!
    MSI Support is pathetic.... if its not in front of them in listed of replies, the answer is always contact the manufacturers.
    Do these idiots not realize it costs money to send a board back and be tested. My last problem with a P965 board Foxconn
    would not boot, sent it back. Board was OK (£30 later) I'm still no wiser, turns out that the board will only boot with certain PSU's!!!
    Anyway hope this helps

  • P965 Platinum and Realtek RTL8111B problem

    I have a dual boot setup on my computer:  Windows XP and Fedora 7 Linux. 
    After booting Windows XP I will have to COMPLETELY UNPLUG the power supply from my computer before booting to Fedora 7 Linux.  The reason:  If I simply reboot or turn off the computer (simply turning off does not remove the power from the mainboard), then the Realtek RTL8111B onboard LAN is left in a state which prevents Fedora 7 Linux from being able to use the LAN.  Fedora simply reports the LAN is not available.  The solution, which I find unacceptable, is to completely turn off the Realtek RTL8111B on the P965 Platinum and use an old Realtek 8129 PCI network board. 
    A better solution would be for the MSI BIOS to reset all of the Realtek RTL8111B LAN chipset's bits to a valid state so that Fedora 7 Linux would be able to properly recognize and use the onboard LAN.
    Again, if I COMPLETELY UNPLUG my computer's power supply Fedora 7 Linux always finds and uses the onboard LAN.  It is only after using Windows XP and rebooting to Fedora 7 Linux without completely unplugging the power supply first that there is a problem.  This would seem to indicate the MSI BIOS is not resetting the Realtek RTL8111B onboard LAN chipset to a clean state when it initializes the system upon booting.
    I am using MSI P965 Platinum BIOS version 1.4
    John
     

    Uhm, I'm having exactly the same issue under linux.
    The router's led will stay off and it looks like there was no network cable connected (Realtek Ethernet controllers are insmod'ed and everything looks fine).
    The only thing I haven't tried is unplugging the power supply's cable ... weird.
    I'm also upset about this problem  >:(
    MSI P965 Platinum - BIOS v1.4

  • P965 Platinum, memory support

    I was looking at the manual of the MSI P965 Platinum (pdf from the MSI website) and I noticed this memory speed support table:
    Does this mean I can't use PC2-4200 (DDR2-533) in this board in combination with a Core 2 Duo (FSB 1066)?
    Also, is this a chipset limitation or one of the motherboard?  I looked at the P965 datasheet and I didn't find anything that seemed to cause this limitation, but I'm not experienced enough in these matters to rule anything out...

    In MSI P965 Platinum User Manual written:
    Quote
    - 4 DDRII DIMMs (DDRII 800 supports up to 4 GB, DDRII 667/ 533
    support up to 8 GB, 240pin / 1.8V)
    Why MSI P965 Platinum is supporting only 4 GB RAM if you use DDRII 800 memory?
    MSI 975X Platinum PowerUp Edition supports up to 8 GB RAM if you use DDRII 800 memory. Compare
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=746
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=745
    It's because MSI P965 Platinum use old one P965 MCH but MSI 975X Platinum PowerUp Edition use the newest one.

  • P965 Platinum shutdown and driver problem.

    Hi all.
    I purchased the P965 Platinum a few days ago, and I got two problems.
    1.
    My computer will not turn off the power when shutting down. I got the message: "It's now safe to turn of the power"
    2.
    In Device Manager i got a "!" in front of the "Intel(R) ICH8 Family PCI Express Root Port 1 - 283F.
    I got the latest inf-files and latest BIOS.
    Anyone got a solution?
    Cheers...

    Changing the HAL made my computer freeze and operate very unstable.
    But I've reinstalled XP and NOW IT WORKS!!!! YEAH!!!
    My computer is recognized as an ACPI Multiprocessor PC, and there are no errors in the system device section.
    It must have been the flashing of the BIOS that did the trick.
    Thanks for all your answers guys.
    I'll go back to loving my new computer now..

  • P965 Platinum/Realtek RTL8111 Connectivity Problems

    I have a P965 Platinum that has the on board Realtek RTL8111.  I have had it since Dec '06.  I have the latest Win Xp.  Driver 5.658.814.2006.  From the beginning I have had connectivity problems.  I have stripped the motherboard of all non-essential components and I have installed XP multiple times.
    Almost every time I boot up, and windows comes up, I get a Limited or No Connectivity error.  Notice I said 'almost' every time.  Sometimes I get connected right away.  I thought it might be a loose cord, and noticed that the left LED on the back of the LAN jack was blinking.  Which according to the manual means that it is talking.  I wiggled the cable around to see if it was a bad connection, nothing.  Then I replaced it and I connected.  Unfortunately when rebooted, it wasn't connected again.  After trial and error, I soon realized that by unplugging and re plugging the cable back in I could eventually get it to connect, which it eventually did every time.  Bad connection right?  Now here is the weird part, if I disable and enable the local area connection under Network Connections in windows enough times eventually it connects!  Here is exactly what I do:  First I disable it and then enable it again.  If it takes more than a couple of seconds trying to connect, I know it will fail.  So I keep doing it until it works.  I thought it was a BIOS or driver issue and being such a new board I thought I should just wait.  No other computer of mine has this problem.
    Thanks in advance for any help or advice.

    Quote from: Puffnstuff on 25-April-07, 10:09:14
    Have you tried using another cable to rule out the possibility that your cable is bad?
    Yes, I tried a new cable.  Same effect.  Now of my other computers have problems with the cable or connection.
    Quote from: HenryW on 25-April-07, 10:09:23
    Have you tried the updated Realtek drivers from MSI (5.664.0205.2007)? Dated 2007-04-20
                        HERE
    Yes, I tried those drivers which are also on the Realtek website.  The funny thing is that it connected the first time!  Unfortunately when I tried it again (reboot and restart) it did not connect.   So the driver upgrade did not fix the problem.

  • P965 platinum ide and sata problems

    in bios om my mb it says that i have ide not sata >:(.
    and i cannot see my cd-rom as an ide.
    i have tried to update bios but it didnt work i tried liveupdate and usb stick.
    when i set my mb to ahci function on my sata config, windows dosent find the disk in the os installation. and my computer cannot load windows.
    in windows something is wrong with the cd-rom when i use it my computer is going slowly.
    i think this problem is caused by the jbmicron software.
    anybody who can help me with this problem??
    Specs:
    Msi p965 platinum
    c2d e6600
    corsair twin2x 2048mb ram
    xfx geforce 7900gt
    wd raptor 10000rpm 74gb
    seagate 160gb sata2
    thermaltake pure power 460w

    Would much appreciate some help if anyone is familiar with this issue!
    I'm having a very difficult time getting the the 965 Platinum to recognize my IDE devices, and I don't know why. I've got a Sony DRU-500A DVD burner in the master position, and a Maxtor 6L300R0 hard drive in the slave position. The jumpers on those devices are appropriate for their position. The devices are "usuable", that is, I've been able to run the Windows XP installer (up to a point) and writes have occured to my hard drive, but the installation fails after the portion where you reboot after all the files have been written from the install disk.
    In any case, the Standard CMOS screen simply never shows any devices detected on either the IDE Primary Master or Slave entries. I've tried disconnecting the DVD drive and just connecting the Hard Drive as master instead with no improvment. I've also tried disabling the SATA configurations, toggling PCI IDE Busmastering. Nothing works.
    I've never been able to boot into Windows.
    There was a point where the JMicron Raid menu showed this drive as a raid drive for reasons that aren't clear to me (the drive may have been a raid drive in the past). I've set the drive back to non-raid, rebooted back into my old system and everything checks out. No problems at all, so I think that there are any RAID issues.
    I'm not a pro at building systems, so there could be user error anywhere alonog the way.
    Any ideas? I'm bamboozled! 

  • P965 platinum questions. Pointer problems

    Alright I have a few questions. I just built a new pc using the p965 platinum board and I'm running into some issue. I was able to get windows going from a previous install. I have a logitech wireless combo mouse and keyboard and it will light up and the keyboard will work when I start the computer, however when I get to the windows login screen the lights from the wireless mouse dock go out and I cannot use the mouse or keyboard to get logged in. While those were plugged I also plugged in a wireless logitech laptop mouse and suddenly the other two came alive. I was trying to install the msi and video card drivers and when I rebooted it did the same thing, it went to the login screen and I couldn't use my mouse or keyboard. I tried the laptop mouse again but it would not work.
    I cannot log into xp and I have no idea why the mouse and keyboard stop working as soon as the login screen comes up. I tried safe mode but the same thing happened. I have no idea what to do since I can't get logged into to change anything.
    The next part is I cannot boot from cd and I'm not sure what button to push to force the computer to boot from cd. I have looked every where but I cannot find any information. All I want to do is to get the pc to boot from cd so I can install either vista or xp. I have gone into bios and and switched it to only boot from cd and yet it still boots into xp. Bios sees my nec dvd burner but it does not show me my samsung cd/dvd drive which is the secondary drive. Both the HD and the dvd rom drives are plugged into a pci IDE controller and they get detected on startup.
    I'm not sure what to do since all I want is to reformat. I would appreciate any help. Like I said before it boots to windows and I was able to get into windows before it's just now my devices won't let me. Please help.ß

    it has to be the driver, as WinXP doesnt come with Logitech driver built-in. What you need to do is to get a wired PS/2 or USB keyboard which Windows recognize. Get into Windows is your mission to accomplish. Otherwise, it's very difficult to know if your wireless keyboard/mouse are really working or not.
    As you said you have access to the BIOS, you may change the boot sequence to load the CD first, then proceed with your Windows fresh instaLL. The boot list button is F8 or F10.

  • MOVED: P965 Platinum memory issues

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=104913.0

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=104913.0

  • MSI P965 PLATINUM...DOES IT SUPPORT VIIV?

    I recently built a new system with the P965 platinum motherboard, after several problems (mostly due to the jmicron) i have the system up and running.  my next step is to network it with my Directv HR20-700.  to do this (without complicated go arounds) the PC networked to the HR20 needs to have the Intel VIIV 1.5 software running on the system.  when i download the VIIV software and try to install it i am getting an error stating that my PC does not meet the hardware requirements for motherboard and hard drive.  i ran the intel chipset test and it indicated that i have a 965G chipset system, is this correct?
    I assumed that this was a VIIV approved motherboard because it is a suppose to be a P965 chipset motherboard.
    please help!

    The strangest thing about the Intel article about ViiV is that they made tests with this configuration http://developer.intel.com/performance/desktop/dighome/test_configuration.htm
    and obviously they are using Intel® Desktop Board DP965LT, witch also doesn't support ViiV. 
    http://www.intel.com/design/motherbd/lt/lt_available.htm
    So,my advice is to contact the Intel support team and ask about your motherboard.

  • P965 Platinum booting problems

    Hi all,
    I have a serious problems with stability of my system. It seems to behave pretty randomly. Every now and then when the power button is pressed the system seems to start booting up for 2-3 seconds, then suddenly turns off and re-boots again. If everything goes ok windows is loaded and sysem is pretty much stable. However every one in five booting attempts ends up with system trying to boot a couple of times, getting on and off constantly so there is not even a chance o get to BIOS. After some time the POST screen shows up saying that an overclocking attempt has failed and system will be restored to te defaults. The story is that there has never been an overclocking attempt whatsoever since I can not get he system running stable at stock settings!!! Anyway, I get finally to BIOS but sometimes next restart of the system occurs and the story is all over again. When I finally get to the settings and restore the defaults the system will reboot alright and for the next couple of times it will turn on normally untill the next doggy start forces me to get to the BIOS and start al over again. Initially I thought that this is due to the fact that the memory runs at 667MHz(2x333MHz) when the FSB is set to 266MHz - FSB:DRAM 4:5. I changed it manually to 533MHz (FSB:DRAM 1:1) but the problem did no vanish. I also tried different memory timings set manualy and by SPD but it also failed. At this stage I used up all my ideas and really do not know what to do know. The memory I have is pluged in in slots 1 and 3 for dual channel operation.
    I bought this motheroard to get fast and stable system that will not failed during week-long simulations and I'm very dissapointed with what I got so far. Below are my system specs:
    Intel E6300
    MSI P965 Platinum
    Corsair 2x1024 PC 5300 matched
    NorthQ 4001 400W PSU
    Gainward GeForce 7300GT
    WD SATA 250 GB
    NEC DVD-RW AD 7173
    Windows XP Pro SP2
    I hope somebody can help me or at least give me a hint where to look for solution.
    Thanks
     

    Quote from: walus on 26-December-06, 20:33:35
    Hi all,
    ....... The memory I have is pluged in in slots 1 and 3 for dual channel operation.
    the only way I have no problem with this mobo is putting ddr moules in slot 3 and 4 (no dual channel)   

  • Msi P965 Platinum with Vista Premium 64bit big problem

    hi i cant run vista properly, i get blue screen dumps that dumps memory.
    Some time it can run 5min sometimes 2hours
    Vista says that there is a hardware incompatiblity something with memory.
    I have run memtest x86 it passed, and Vistas memtest fail.
    tryed to run with only one memory and changed place to them
    core duo center doesent work either.
    now i run windows Xp with latest drivers and everything works just fine.
    I want to run my computer on windows vista 64bit, whats my problem

    Sad to hear about those problems, especially since I am going to upgrade to Vista myself in the nearest future.
    I have no guarantee that this will work, but try using manual settings for RAM. And set RAM to 5-5-5-15, not 4-4-4-12. And run RAM at stock speed, and the same goes for FSB etc.
    And try using 2,1V for the RAM.
    If you have runned on manual settings, set the to "Auto" if you haven't tried that.
    I have read abuot one guy that got bluescreens all the time when he overclocked in Vista. You haven't overclocked, have you? :P
    EDIT: I see you use BIOS v1.3. Try flashing to v1.2.
    I flashed from a bluescreenfree system at high overclocks (v1.2), to a instable system vith plenty of bluescreens when exeding 340-350FSB.
    With BIOS 1.2, I have booted with FSB 389, and been able to run SuperPI, CPU-Z and some other small programs. Now, with BIOS 1.3, I can't get into windows, get bluescreen before logon is complete.
    I think there is something "wrong" with the northbrigde in P965 Platinum, because the errors are allways memory related.

  • Neo 2 Platinum Memory Problem

    Hi There,
    i have here two PQI DDR400 PC3200 512MB dual-sided, one crusial DDR400 PC3200 512MB one-sided and one crusial DDR400 PC3200 1024MB dual-sided.
    Here's the problem:
    When i install all the four modules my computer wont bootup it will only give one long beep inducating that there is a memory problem. All four modules where tested separetly with no problems. I have now only the two crusial modules on my Neo 2 Platinum running with no problems.
    Can some one help me so i can use all four modules please???????

    Assuming they will all work together, it sounds like the BIOS isn't set up properly, or the board isn't detecting the speed correctly. When installing more than 2 dimms, most boards, due to the memory controller on the CPU, will set the RAM to the 166 divider, or DDR333. Generally it will also set them to the 2T command rate. 
    If you have a Winchester core you will more than likely need to run DDR333 with the 2T setting. On a Venice you may be able to get away with DDR400...I know on an Opteron you can do DDR400 with the 2T command rate easy enough...I will assume it is probably the same with the newer cores as well.
    Again, IF they all work together (mixing and matching dimms may not always work), you may just need to set the BIOS up properly. Pop in the sticks that work, go into the BIOS and set the RAM to the 166 divider, and then make sure the command rate is on 2T. Be sure all the RAM can run the timings that are set in the BIOS. Save and exit. Then power down and unplug the PC, pop in the other stick and see what happens.
    If that doesn't work, you can try different slots, or an even a lower RAM divider (probably won't make a difference). IMO, if all the settings are correct and it still won't work, I would guess that mixing the RAM is the problem. I have seen it happen - I have also had weird RAM configs work perfectly, so it is kind of hit or miss...I hope some of that helps, good luck.

  • P965 PLATINUM / REALTEK network adapter connectivity problem

    hi,
    I cannot connect my PC with my laptop using a crossover ethernet cable. All of the crossover cables I have tested operate as expected when used to connect other computers. A fact that complicates things more is that the connection status is indicated as "connected" in the network connections window but no packets are received at all.
    My configuration:
    MSI P965 PLATINUM (flashed with v1.2 BIOS)
    OS: Windows XP PRO SP2
    REALTEK driver version: 5.654.721.2006
    Network IP, mask and gateway are manually assigned.
    Note1: The network adapter works totally fine when connected with my router using a straight UTP cable.
    Note2: My brother's PC (which has exactly the same configuration as mine) has the same problem.
    Thanks in advance

    Thank you all for your tips.
    Please note that network file sharing is enabled. If I use my ADSL router as a gateway (it is 192.168.1.1 as you can see in the ipconfig commands output) the computers do communicate.
    Problems arise when I use a crossover or straight cable to connect directly my desktop and laptop. Some things I have tried:
    - I have disabled the firewalls on all computers.
    - If I ping the localhost (127.0.0.1) I get packet replies. However, when I ping the other host I get timeouts.
    - I have set the connection speed manually from the device manager to 100mbit/full. Still no good..  :(
    P965 PLATINUM (DESKTOP PC)
    Code: [Select]
    C:\Documents and Settings\Administrator>ipconfig /all
    Windows IP Configuration
            Host Name . . . . . . . . . . . . : desktop
            Primary Dns Suffix  . . . . . . . :
            Node Type . . . . . . . . . . . . : Unknown
            IP Routing Enabled. . . . . . . . : No
            WINS Proxy Enabled. . . . . . . . : No
    Ethernet adapter Local Area Connection:
            Connection-specific DNS Suffix  . :
            Description . . . . . . . . . . . : Realtek RTL8168/8111 PCI-E Gigabit Ethernet NIC
            Physical Address. . . . . . . . . : 00-16-17-EF-3B-04
            Dhcp Enabled. . . . . . . . . . . : No
            IP Address. . . . . . . . . . . . : 192.168.1.2
            Subnet Mask . . . . . . . . . . . : 255.255.255.0
            Default Gateway . . . . . . . . . : 192.168.1.1
            DNS Servers . . . . . . . . . . . : 192.168.1.1
    ACER ASPIRE 1403 (LAPTOP)
    Code: [Select]
    C:\Documents and Settings\Administrator>ipconfig /all
    Windows IP Configuration
            Host Name . . . . . . . . . . . . : laptop
            Primary Dns Suffix  . . . . . . . :
            Node Type . . . . . . . . . . . . : Unknown
            IP Routing Enabled. . . . . . . . : No
            WINS Proxy Enabled. . . . . . . . : No
    Ethernet adapter Local Area Connection:
            Connection-specific DNS Suffix  . :
            Description . . . . . . . . . . . : Intel(R) PRO/100 Network Connection
            Physical Address. . . . . . . . . : 00-02-3F-B1-F7-89
            Dhcp Enabled. . . . . . . . . . . : No
            IP Address. . . . . . . . . . . . : 192.168.1.99
            Subnet Mask . . . . . . . . . . . : 255.255.255.0
            Default Gateway . . . . . . . . . : 192.168.1.1
            DNS Servers . . . . . . . . . . . : 192.168.1.1
    Is there any utility to check my network adapters? It is a VERY weird situation, because on both adapters the green light is constantly ON, and the orange flashes from time to time. I assume this means that on hardware level everything is fine. Moreover, I cannot believe that there is a firewall/AV that interferes, because even if I shut them down, I still can't ping the other host. 
    Thanks in advance

Maybe you are looking for

  • My itunes wont connect to the internet help :S

    my itunes keeps saying im not connected to the internet when i am

  • How to create a dvd from iMovie '11

    I have created a video in iMovie and am trying to transfer it to a DVD.  However, there is no Export function.  When I share the movie to a file it uses a .mp4 format which is then not able to be be burned to a disc.  In the past, the extension was .

  • Notification settings not being saved

    Anyone else having the trouble that the notification settings are being reset everytime you log-in or restart? Furthermore, login items are not respecting the 'hide' option.

  • When there is a need of END SELECT

    Hi,    give me a clear view about the presence of END SELECT stmt in SELECT query. In some places its not used                                            Thanks

  • Only distince rows in target data store

    Hi I have an interface in which the joins in the source tables will generate duplicate rows but , I want to load only distinct rows in target datastore . How do I achieve that in ODI ? Thanks