Pairing and connecting to Moto Cliq
I have set up my new Moto cliq to connect to my mac pro via bluetooth, however I cannot get it to connect, all it does is pair. Im trying to use as a modem, if anyone know how to fix please help. I have tried to call T-Moible but they cant help with this issue due to modem use with this phone is not supported. But it sounds like it is possible.
Hi! and welcome...
Can you see the printer in the Bluetooth Setup Assistant or does it fail at the pairing stage?
try this article...
'Bluetooth: Pairing fails if you do not allow initial scan to complete'
http://support.apple.com/kb/TS2225?viewlocale=en_US
Similar Messages
-
Bluetooth paired and connected, but not showing up in device list
I have a iphone 4s and a plantronics discovery 975. It was working fine, I don't recall doing any updates... But now, it's showing paired and connected, but when I make a call, it's not connecting and doesn't sho up in the the device options - only shows speaker. I already did the 'forget device' and re-paired it and it still won't work. If I press the call button twice on the bluetooth, it'll call the last number dialed, so I know there's some connection... I'm lost... Any help would be appreciated!
Oh! And here's another weird thing. My nephew was visiting yesterday, helping me move furniture and he asked could he get on my wifi. I opened the network lock and put the password in his phone myself and it never gave me a notification that he had connected. Later, my dad came over and when his phone connected to my wifi, it let me know that he had connected. Wonder what's different about these 3 devices (blu-ray, 2 iphones). None were listed in the network map before I allowed them to connect yesterday.
-
Should my iPhone 1 (iOS 3.1.3) with Bluetooth 2.0 (Handset HSP?) work with wireless earbuds with BT 4.0 and the Headset (and Handsfree, A2DP, AVRCP) protocol? They pair and connect as expected (with a PIN); status bar looks good and shows Bluetooth active, and I even see the iPhone displays the battery levels of the wireless earbuds. But audio always comes out the speaker. (If I plug in wired headphones into the headphone jack then audio comes into the wired headphones, as expected.) I have rebooted the iPhone; I have had it forget about the wireless earbuds, and repaired and reconnected; I have reset all network settings. Thx in advance.
PS: I understand that more recent versions of iOS have a way to choose where audio output goes (speaker, headphone jack, Bluetooth device). Does this older version of iOS? I could not find an option or setting.I've noticed this lately as well, with my iPhone 4. I couldn't confidently pin it directly on any particular iOS update, but my iPhone used to automatically connect up via Bluetooth with my Prius's handsfree feature, and now it doesn't. I work with a CE-based device at my job, with Bluetooth capability, and I used to test out that feature by having it discover my iPhone. This no longer works either.
What I have found (not really a solution, but it does work and may be a clue for Apple) is that if I simply go to the Settings app then the General -> Bluetooth screen and let it sit there, it will pair right up with my car within a few seconds. Bluetooth is always on, and always says "Now Discoverable" at the bottom of the settings screen. -
Can i pair and connect lg to mac, can i pair and connect lg to mac
can i pair and connect lg 540 phone to my macbook pro
In that case, you can configure the AirPort Express to "join" the wireless network that the Home Hub is providing and stream AirTunes from your computer to the Express over the wireless network.
Things will work just fine as long as the Express is located where it can receive a strong wireless signal from the Home Hub. -
6280 with iPAQ h2200 - "pairing and connection rej...
When I attempt to pair my 6280 with my iPAQ h2200 I get an message "pairing and connection rejected for security reasons"
No problems pairing the 6280 with my PC or headsets, and no problems pairing my iPAQ with other devices or my Motorola A925 or A1000.
Is there a setting on the 6280 which will allow this pair?Thanks, I found the Bluetooth Security update for iPAQ h2200 at http://h18007.www1.hp.com/support/files/HandheldiPAQ/us/download/21093.html
Now works fine. -
Jawbone Icon pair and connect to 4s but stopped working after 2 weeks.
The 4s shows the headset is connected and paired, but when a call is placed it does not show the bluetooth on the phone menu and does not send audio to the jawbbone. The jawbone also thinks it is connected and will give you a report of how much talk time is remaining. You can redial and answer by pressing the jawbone button, but the sound goes only through the phone and not through the jawbone. Setting the 4s to "forget" the headsets and then repairing them does not change the problem. Renaming the headsets and then re-pairing them does not fix the problem.
Finally, I tried what I should have tried first. I turned off the phone and turned it back on. Voila. I am posting this so people will be sure to try the easy solution first if you have this same problem.Never mind!
I knew to check for lint stuck in the iPod and I had cleaned it out but figured "screw it" and gave it another try. Turns out I didn't go deep enough and there was still lint stuck in there. Got it all out now and it works perfect! -
BT headset pairs and connects, but doesn't auto-select
I'm posting this hear because I'm using Gnome front-ends to negotiate the bluetooth profiles/etc, but I know that it might be bluez or PulseAudio that's "faulty" here. That said...
I've got a pair of bluetooth headphones that work great. They pair, connect, and play audio just fine. However, once they've connected, I have to go into the audio settings dialog and select them over the default "Digital Output" device. It's the epitome of first world problems, but I kind of expect Gnome to figure out that the headset is the intended destination for audio streams, much like it does when you plug headphones in.
So, what's missing? I found some lengthy discussion on potential bugs in Ubuntu 12.04 when I Googled for this, but they seem to blame bluez < 5.0, whereas I'm running bluez 5.28-1.
Thanks in advance.You could enable pulseaudio's "switch-on-connect" module, as per wiki. This means that once a new audio device is connected, all audio input will be routed to it.
-
HT204387 how do i pair and connect my iphone 4 to an htc evo
I cannot pair my iphone 4 to an htc evo using bluetooth to send pictures
junkie8178 wrote:
iphone cannot be paired with a non-apple device
Strange... By Bluetooth earpiece is a Jabra.. not Apple.. -
iPhone 4S upgraded to IOS 7.1.2. Since then, Honda Handsfreelink would not connect, I un-paired and re-paired phone on 2 prior occasions successfully. Now I deleted system settings in car, tried to pair another BlueTooth (Plantronices M20 that had previously been paired wtih iPhone unsuccessfully. I have tried troubleshooting with Honda HFL, Verizon Tech Support, reset network settings on phone and I can no longer get the Bluetooth to pair. I was told to bring phone to VZW store. I was also told to reset phone to default settings which I do not want to do.
How to Pair Your Plantronics M20 Bluetooth Headset, M20 Pairing Guide - Plantronics Headsets from Headsets Direct
You have to reset the plantronics device before you can pair successfully. With my new iPhone the plantronics web site said to reset the headset and then pair.
Your car dealership is best equipped to connect to your phone with your Honda. Physically go to the dealership.
Good Luck -
My wireless keyboard no longer connects with my iMac since changing the batteries. It now shows as not connected, not paired and not configured. A friend recently connected his iPad to the iMac and since then the problem started. Any ideas to resolve this?
a friend told me that he wants my os x cd for my macbook pro to upgrade his imac.
The discs that come with your Mac are "machine specfic" and cannot be used on another Mac. -
I bought ATV 2 about two weeks ago. The setup was easy and I set up my Home Sharing, screensavers, and I was watching Netflix within about 20 minutes. I had a good week of no trouble and enjoyed the device immensely. I updated the software when prompted and continued to watch movies and play music. Then something happened: in the middle of viewing, ATV 2 stopped working, the screen went blank, and the little white light started blinking slowly. When this happens, the ATV manual "troubleshooting" section merely says, "Apple TV is having problems." ***? Strangely, it would come on and act fine for a few moments as if nothing happended (for only a minute or two), then click off again.
I attempted to RESET the device by using the Down/Menu combo -- nothing -- the white light blinks really fast but still no picture on the TV (just the Apple logo); I unplugged it and plugged it back in -- no fix; then, I RESTORED the device and had to re-enter Apple and Netflix account info, passwords, set up shared photo folders, etc. Afterwards, it worked. I watched movies right where I left off and went on with life until a few days ago when I wanted to finish a movie... The movie was going fine - no problems at all - until ATV 2 stopped working again!
So, the remote works [it is paired and sends commands as it should], the HDMI connection to HDTV is fine, the stereo receiver connection is fine (for audio, using an optical cable). But the only thing on the TV is the Apple logo. Resetting ATV 2 doesn't work; and I could restore it again but that seems like a HUGE waste of time, and something I am not prepared to do each time I want to use the device.
What could be the cause? Wireless interferrence, software/update flaws, need for firmware, or malfunctioning hardware? ATV 2 is a $100 paperweight until I get answers.After some sleuthing online, reading a compilation of Q&As here, and visiting the local Apple Store, I think the problem and "solution" may be found in HOW my ATV2 is connected to my stereo. For some reason that I have not figured out, when the RECEIVER either switches from one setting to another, it somehow disrupts the ATV.
The ORDER of how you turn ATV on and off is key. If you start with everything OFF (ATV, HDTV, stereo Receiver), then turn on the receiver, then turn the HDTV, put the TV to the input setting that is connected to the ATV, THEN turn on the ATV by hitting the Play button on the remote.
Note: The ATV light may come on once the HDTV is turned on and put to the correct setting, but you will not see a picture on your TV yet.
You should be up and running on ATV (without having to reset, unplug or restore). Apparently, I was using my universal remote that essentially turned everything (HDTV, Onkyo Receiver and, by extension, the ATV) on at the same time, confusing ATV and causing that evil blinking white light. The ATV connection was lost.
When you are done with ATV, you must put ATV to sleep FIRST... each time. The command is on the main menu, to the far right, at the bottom [Sleep Now]. Once you press Sleep Now, the ATV will go off. THEN you can turn your receiver/HDTV off (or to whatever other setting you want for watching regular tv, music, etc.). I was simply switching my HDTV and Receiver 'away' from ATV when I was done... But I would return to a blinking light and no ATV. The solution above is a work-around that seems to do the trick.
The thing Apple needs to fix is to make the "Sleep Now" command a simple process on the remote so you don't have to back out of everything you were watching to get to the main menu for the Sleep Now command. Or in the next update Apple merely needs to improve ATV2 so it can work no matter what order you open or close it on a HDTV/Stereo.
Note: Other people have suggested that you just hit the select or Menu button to put ATV to sleep, but that did NOT work for me.
I figured this out through trial and error so I hope it works for you too. -
My IPhone 4S with version 6.1.1 will not stay connected to the bluetooth in my 2012 Subaru Outback. The phone is paired and registered with the bluetooth in the car, but each time the ignition is turned off the phone loses connection with the bluetooth and I have to select the device again.
You posted in the iPad forum instead of the iPhone forum. To get answers to your question, next time post in the proper forum. See https://discussions.apple.com/index.jspa I'll request that Apple relocate your post.
Cheers, Tom -
What are the pinouts of the SH68-68-EP cable (picture please) showing shielded pairs and shield connections.
you can find the pinout in the manual of that product in which that cable used or for specific device for which sh68-68-ep built for.otherwise see differents catalogas on www.ni.com and search for this.
thanks -
I use my cell as my home phone and the GE Gateway worked fine with my old LG flip phone. I have been unable to get the IPhone 4 to connect.
It sees the GE21518 and connects for 1/2 second but then goes to not connected. I have a Motorolla T505 in the car as a hands free Bluetooth and that seems to be working OK. Anyone have experience with the GE Gateway or other suggestions. Thanks!I use my cell as my home phone and the GE Gateway worked fine with my old LG flip phone. I have been unable to get the IPhone 4 to connect.
It sees the GE21518 and connects for 1/2 second but then goes to not connected. I have a Motorolla T505 in the car as a hands free Bluetooth and that seems to be working OK. Anyone have experience with the GE Gateway or other suggestions. Thanks! -
when I connect my apple tv to my access point upstair and connect my ipad to the same access point i cant see my apple tv when i open up the airplay menu on my ipad. but i can see the apple tv in the living room downstair which connect to the main router.
Below is some info i get about ports.
I tried to set DMZ on my main router to have full access to ported to access point upstair which is in the ip of 192.168.1.2 and the main router in the living room is the gateway router with the 192.168.1.1 ip.
I still cant see apple tv after i try the DMZ method.
any suggestion ?
These network ports are used by Apple TV for communications on your network.
TCP port 123 is used to communicate with a network time server.
TCP port 3689 is used to communicate with iTunes while using the iTunes Library Sharing feature.
UDP port 5353 is used by Apple TV for automatically finding computers with iTunes on your network using Bonjour.
TCP port 80 is used for communicating with podcast servers.
TCP port 80 and 443 are used for basic and secure communications with the iTunes Store via the Internet.
TCP port 53 is used for regular DNS.
These are well-known ports used by Apple products, like iTunes. If you can use all the features of iTunes, these ports are likely already open on your firewall or NAT router. Note: These ports may also used by other services such as YouTube and Flickr.When the Apple TV is paired with a remote, it means only that remote can control it, when it's not paired any remote can control it. You will need a remote for each of your devices.
Maybe you are looking for
-
How do I arrange photos in iPhoto slideshow?
On my iPad - the album that I created in Photos appears in the iPhoto app as expected. Only now the sequence is out of order in the iPhoto slideshow. It does not match what is in the Photo album. How do I move the slides in the iPhoto app to the corr
-
Allowing access to select few public objects (moved from Native forum)
I am moving my posting from Java Forums > Fundamentals > Key Classes > Native forum to this one. Sorry for posting it on the wrong forum earlier. Before each reply I have added a lien for clarity. Allowing access to select few public objects Author:
-
Characters Standart between Pc and Mac
Hi, My application which is parsing html pages and output some part of this pages has no problem to manage the different charset when used on a PC with J2re 1.4.1 . But this application used on a Mac Os X with J2re 1.3 output many wrong characters ev
-
Bank Type in Payment Transactions in Customer master record
Key you enter in the line item to specify which business partner's bank the system should use. Exactly what key it is talking about. In case i have 3-4 banks.
-
Can we develop a solution in Visual Studio 2012 and still deploy it on BizTalk 2010?
Can we develop a solution in Visual Studio 2012 and still deploy it on BizTalk 2010? or Is it that solutions developed in VS 2012 have to be deployed only to BizTalk 2013? Thanks