Pairing AX with Third Party Router

Hi,
I try to set a network by connecting AX with thrid party WiFi router (to create a router network). I can not manage to pair it as I wish, but I am aware that not all Third party router are able to connect with Airports and WDS.
I try to pair with a Sitecom (WL-026)
Do someone knows about AX -3rd Party comaptibility?
Thanks
Yann

Since I'm not at home, I can't go into my AX config right now. However, is what you're suggesting quite easy (i.e., setting up my AX to connect to my NON-WDS supporting 3rd party P.O.C. router's network)?
I am currently doing it the brute force way: two separate networks, one (3rd party) connected to the world, one (AX) connected to the stereo. This is all well and good except that I have no internet connectivity when I'm using the stereo. OK... not so well and good.
Any help would be greatly appreciated.

Similar Messages

HomeHub2 as Modem with Third Party Router, Securit...

okay i've configured my Homehub to be set as a Router and conencted a Belkin G Plus Mimo router as the third party router, connection and everything is fine but theres on problem...
security, there is no scurity protecting my wireless network which means everyone can access my network which is bad.
when i try accessing the third party router (belkin router) i'm forwarded to the BT home hub control panel page...
any help? i need protection on my wireless!
Kind Regards, Bert

Hi Bert,
What you will need to do is manually change your Network Adaptor to an address in the 192.168.2.2-255 range. Set the gateway to 192.168.2.1 and try and access your third party router again. Then enable the DHCP Server on the LAN interface of your Belkin router.
Don't forget that you have to be connecting through your Belkin router in order to use it properly like Computer - Belkin - Homehub, not Computer - Hub - Belkin otherwise it will just ignore the additional router (Belkin).
You will also need to add a Static Route on the Belkin and set the Destination network to 192.168.1.0/24 and set the gateway to 192.168.1.254 in order to access the internet and Homehub. This will need to be set on the WAN interface.
I hope this helps.
Like this post? Give it a Star . If this post answers your question, please Mark it as the Accepted Solution.

Time Capsule and time machine with third party router

Hi,
This is the first time I use this site.
I have over three years old Mackbook.
APP has expired.
Now I want to know how to set up time capsule in a new environment.
I moved from Australian and Singapore.
I was using Time Capsule and Airport Extreme in Australia.
I have moved to Singapore.
I am using router provided by Singtell(Singapore Telecommunication). I do not have an Airport Extreme anymore. My housemate and I are using wireless internet-sharing. Needless to say that internet provider is SingTell.
Now I would like to know how to use time capsule and time machine with the network created with a router provided by SingTell.
What I did so far is;
Connected the time capsule to the power point.
Orange lamp lit and flashed for a few second and stop. Orange lamp stayed on.
Apple Utility does not recognise Time Capsule.
I prefer to use it wirelessly.
There are only two USB cable ports installed.
One is used to synchronize iPhone.
Other is used for a printer.
but if it is not possible, wired would be OK.
MacBook 13 inch 2.0 GH Late 2006
I hope that someone able to give me an answer for this.
Cheers,
morepubholidays

In this case the apple support people reveal a truly poor understanding.
You must bridge something.. you either bridge the TC.. which 90% of people do.. or you bridge the dsl router.. which some people do manage to do.. You will have to look that up for your modem and check with verizon if they support pppoe authentication.
IMHO just bridge the TC as you were told not to do.. as they are simply wrong about that.
If you already tried this and it didn't work.. try again.. it is the correct approach.
You have no choice. But this time let me suggest you do it using the 5.6 airport utility.. as the apple toyland v6 airport utility is likely half your trouble.
So here is how to get the utility into your computer.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall 6.1 so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.
For screen shots see this post.
https://discussions.apple.com/thread/4668746?tstart=0
Then open the manual setup on the 5.6 utility.. go to internet tab. Connection sharing.. off bridged mode.
Select this and update..
Then all your IP addresses will be wrong.. I suspect this is where things are going wrong.. and messing you up.
Once the TC is bridged.. turn off everything and restart.. in correct order.. modem.. TC.. client computers etc. 2min gap between each.

Connection timeout with third party router

Recently went to Apple store to fix wireless connection problem. Per their recommendation, reformatted and reloaded Snow Leopard (at their store) hoping to get my macbook reconnecting to wireless router (netgear). Have another macbook, itouch, ipad2, and pc that all connect to the same router, no problem. The problem MB connected at the Apple store no problem. Now that I am back home, this older MB continues to have the 'connection timeout' reading. Researched a ton on the internet. Found no solutions. Any suggestions?

It might help to reset the connection settings on your Mac using these steps one at a time until the problem is resolved, recognizing that, depending on your problem, not all of these steps will make sense:
1) Use the AirPort/Wi-Fi menu bar item to turn AirPort/Wi-Fi off, then on again.
2) Try to select your Wi-Fi network from the AirPort/Wi-Fi menu.
3) In the Network panel of System Preferences delete the AirPort/Wi-Fi item from the left column, then add it back.
4) In the same panel as (3), define a new location and see if you can make that work.
5) In the same panel, select the AirPort/Wi-Fi connection item, click the "Advanced" button, select the "TCP/IP" tab, then click "Renew DHCP Lease". Note that the fix this step implements may be temporary.
6) In the folder /Library/Preferences ( _not_ <yourhomefolder>/Library/Preferences), move the folder SystemConfiguration onto the Desktop, then restart your computer. See if you can now make your AirPort connection work.
These steps may not help, but they'll only take a couple of minutes to try. Before you try these, if you have any special network settings on your Mac for things like DSL credentials, note all your network settings, because the latter steps will destroy them. If you got all the way to the last step, if things don't work any worse than before, you can trash the saved SystemConfiguration folder.

Is it possible to use a third party router with BT...

Hi all,
I currently have BT Infinity & Unlimited calls on my package, but I use a third party router, namely a Netgear WNR3500L in place of my original v2 Infinity Home Hub.
Now, my question is this: Do I have to use a Home Hub with Vision, or would I be okay using my current setup?
I do realise that if I use a third party router, I won't get support from BT.
Any help would be greatly appreciated.

plainview wrote:
Hi, this has been brought up before on this forum;
http://community.bt.com/t5/BT-Vision/Best-non-BT-Router-for-BT-Vision-Use/td-p/243097
http://community.bt.com/t5/BT-Vision/using-another-router-with-bt-vision/td-p/7742
http://community.bt.com/t5/BT-Vision/Do-I-need-to-use-the-BT-Broadband-modem-with-BT-Vision/td-p/484...
Thanks for those links, plainview. Much appreciated. Have a shiney, new star!

Airport with third party wireless router?

Will Airport Extreme units play well with third party routers? I have Verizon FIOS and would like to use my Airport Extreme base station and Airport Express unit on my home network. I have successfully set up Airport Express in my office as a WDS. Can Airport Extreme base station be set up as part of a WDS?
Thanks for any insights.

Will Airport Extreme units play well with third party routers?
No industry-wide standard exists for WDS, so it is impossible to predict how Apple's implementation of it (or anyone else's for that matter) will interface with other equipment.
Wikipedia has a short but fairly comprehensive list of third party equipment that allegedly support WDS. Missing from the list is a Linksys access point, which I nonetheless successfully configured as a WDS remote station. They call it "repeater mode".
Yes Verizon FiOS is absent.

Connecting to third-party router, but unable to browse or e-mail

I am using an Airport Extreme card in my PowerBook G4 running firmware version 405.1 (3.90.34.0.p18). Our office Wi-Fi access is through a third-party router. We used to use MAC address filtering, and I had no problem accessing the network.
Recently, for reasons unclear to me, our IT director ditched the MAC address filtering in favor of the WPA-personal standard. I was able to enter the encryption key and get connected to the network, but I wasn't able to get my browser to access the internet, nor send or receive e-mail traffic.
Our IT folks temporarily disabled all security and restarted the wireless router, but I was still only able to connect to the router, and not use my browser or e-mail, so it doesn't seem to be a problem with the use of WPA per se. I tried temporarily turning off my own firewall, too, but the problem remained.
Oddly, I can open up the Terminal and Ping successfully to an outside address -- only http and e-mail traffic seems to be blocked. The Windows-based PCs seem to be able to connect to the wireless network and use their browsers to access the internet without any problem. Any thoughts as to what else I might try, or have the IT administrators try, to resolve the problem?
Thanks,
Sid

Hello kilgores. Welcome to the Apple Discussions!
Something to ask your IT staff is if they use a proxy server for Internet access. If so, do they require proxy configuration scripts (.pac) to provide access to the Internet through your company's firewall. This information would normally be added to your browser's settings.
For Safari: Preferences... > Advanced > Proxies > Change Settings... > Automatic Proxy Configuration

Connecting a third party router to accompany actiontec router?

So I'm thinking about ordering a second router but I don't want to replace the actiontec router that Verizon supplied me, only because I don't have any clue what to do with my STB's so I'm going to leave the Actiontec specifically for that reason. I have the exact same setup with this exact router at my father's house and nothing seems to have gone wrong. Except that we hooked up an extra room specifically for the third party router. This time, I have nowhere for that to happen, so I was thinking about buying a moca bridge and plugging it in to an existing coaxial jack which another STB is plugged into. If I did this with the new router and simply gave only the one STB internet connection via Ethernet through the third party router, and left the rest on the actiontec, would it still work without messing anything up? Thank you.
Solved!
Go to Solution.

I'm not exactly clear what it is you want to accomplish, but if I understand correctly that you want to have an Ethernet connection for a single device in another part of your house, a part of the house where there's an existing coax feed, then a MoCA adapater should do the trick for you.
If indeed you're just trying to get that single Ethernet connection you won't need another router. You can plug the Ethernet device directly into the output of the MoCA adapter.
If you need more than one Ethernet connection after the MoCA adapter what you can use is a simple and inexpensive Ethernet switch. Again, you don't need another router.
The only case I can envision for needing a second router in your situaiton is if you want to use it to extend WiFi coverage, but just for Ethernet connection(s) a second router is not needed and may be counter productive.

Configuration of third-party router

Hello,
I'm trying to configure a router in place of my BT Home Hub. I am pretty sure it has to be PPPoE because it's ethernet out the back of the Home Hub. I tried what was posted on these forums, I used [email protected] with 'bt' as the password. However, the PPPoE connection just times out.
One place I saw said I needed to configure a VLAN of 101. No luck with or without a VPN.
All I ever get is a timeout. If I plug the ethernet from the modem back into the BT Home Router, it works fine, so I know my line works.
Some of the settings I can change in the third party router are:
PPPoE Username
PPPoE Password
MTU/MRU
VLAN (yes/no) and VLAN ID
Encryption (yes/no)
Mac Address (default or I can enter one)
Do I need to power cycle the VDSL modem and leave it off for a period of time to get it it to forget the BT Home Hub? I did try power cycling for maybe 5-10 seconds but to no avail.
In the PPP log, all I ever see is PPP Timeout.
Anyone have any idea how to get this working?
Michael Grant
Solved!
Go to Solution.

Hi mgrant,
The information at the bottem of the article in in Keith_Beddoe's personal website may help. Link: Using your own router for Infinity
The MTU Size needs to be set as 1492
Cheers
jac_95 | BT.com Help Site | BT Service Status
Someone Solved Your Question?
Please let other members know by clicking on ’Mark as Accepted Solution’
Try a Search
See if someone in the community had the same problem and how they got it resolved.

On the continuing saga of third party router problems......

I got an Apple TV which works great with my wireless Airport WDS, but then I was looking into any problems people could be having with it and ran into this:
http://discussions.apple.com/thread.jspa?threadID=901401&tstart=0
Check the third party router problems where Airports worked great.
Networking is ...networking, but you also get what you pay for.

Hi mgrant,
The information at the bottem of the article in in Keith_Beddoe's personal website may help. Link: Using your own router for Infinity
The MTU Size needs to be set as 1492
Cheers
jac_95 | BT.com Help Site | BT Service Status
Someone Solved Your Question?
Please let other members know by clicking on ’Mark as Accepted Solution’
Try a Search
See if someone in the community had the same problem and how they got it resolved.

AX as remote WDS with 3rd party Router

Hi
I have a third party modem/router of which I would like to expand the wireless network with a new Airport Express
The router uses 802.11g so my understanding is that the only way to extend the network is using WDS
On the router I can enable WDS and scan for available access points. The Airport only shows up if previouslòy configured to create a wireless network, but not if is joined to the router current network, I believe this is expected behaviour but not sure.
If I enable WDS and add the Airport from the router config menu the Airport continues to distribute its own IP addresses (10.1...) while the router addresses are (192.168...) and no Internet available
I am sure I am missing some configuration on the Airport side regarding enabling as a remote WDS base station, I believe I can change the AX IP addresses to match those of the router(192.168...), also I have vague memories of needed NAT config as well... Doeas anyone have instructions on what needs to be configured on the Airport?
Many thanks
Francesco

WDS was never adopted as an official industry standard, so manufacturers were left to their own as far as the implementation of WDS.
The chances that an AirPort Express would be able to connect to a third party router using WDS settings are extremely small. Even if it might work, you will likely not be able to use any type of wireless security on the network.
Look over Apple's WDS instructions for connecting two Apple devices together to see if there might be a clue in there somewhere that you have overlooked.
Unfortunately, you may not even be able to "see" the WDS settings in AirPort Utility, since the instructions state than 802.11n devices like the new AirPort Express should not be used with WDS. Good luck!
http://support.apple.com/kb/HT4262

Really Apple? OSX 10.8.5 disables built-in camera functionality with third party apps such as Skype and Gmail video chat. I do not have time machine on my 2013 MB Air. How can I get back to 10.8.4?

Really Apple?
With the release OSX 10.8.5 Apple has once again showed its true colors, and continued its efforts to create a closed Apple system, which eliminates third party vendors, unless, one can only assume... they pay.
Included in this OSX update is the disabling of the built-in camera to work with third party applications such as Skype and Gmail video chat. No surprise the camera works just fine with Apple apps such as Facetime and Photobooth.
The answer I got on my call to AppleCare to ask for assistance in reinstalling 10.8.4, so that I may Skype again, was we can not do that. You can not go back unless you have a time machine bkup.
Can anyone help me get back to to 10.8.4 on my 2013 MB Air?
I do not have a time machine bkup as this computer is not used to store important documents.
Thank you.

Read this post: 10.8.5 Broke Camera Usage For 3rd Party Apps Like Skype
Another: isight not recognized in Skype after 10.8.5 upgrade
Don't panic. Skype simply needs to update its app.

How to integrate single sign on with third party system

we are in the process of implementing istore application. we already have home grown isupport application to contact support personnal for any issues. Now we are wondering how do we integrate oracle applications single sign on with our third pary system. Is there any recommendation provided by oracle to achieve the same.

We too are in the process of implementing iStore with SSO features.
And if you believe me it seems to me as nightmare.
In our scenerio we are intgrating this SSO with Third party access control too (AD and Siteminder). I would request you to please respond me on the following mail id , so we can share our experince which will help us in our implementation
[email protected]
regards and thanks in advance
Vikas Deep

SharePoint 2013 on-premises integration with third party email account

the Email sending issue from SharePoint is causing too much time waste
First let me explain how our SharePoint is deployed
Sharepoint version : 2013
Deployment type : on-premise
Authentication : from Domain controller also hosted locally
domain name ; say domain.com this domain.com is same as our website address hosted on godaddy
SharePoint computer name on local DNS : sharepoint.domain.com
OS and IIS : 2008 r2 , IIS 7.5
Network firewall : 25 26 ports opened for sharepoint , both incoming and outgoing.
Server firewall : turned off
Email configuration Attempts by IIS 6.0
We tried following setting on IIS 6.0 SMTP local server properties
In General tab
qualified name was shown as : sharepoint.dts-solution.com
IP assigned : sharepoint server IP , advanced putted two entries of IP with ports as 25,26
In Access tab
Authentication : selected as Anonymous
Connection : All except below list : empty list
Relay : only the list below , one entry as 127.0.0.1 and other is local static IP of SharePoint server
in Delivery tab
outbound security : Basic authentication : accessed user in AD and given the right password, also checked with annonymous -not working
outbound connection: all default values and port = 25
Advance : fully qualified domain name = sharepoint.domain.com , DNS test showed success, rest every check box unchecked
On sharepoint central management settings
Outbound email = sharepoint.domain.com
from and reply to address = [email protected]
IIS 7.5 SMTP settings
In IIS 7.5 sharepoint application we added SMTP settings as smtp server = godaddy out going smtp , user name as [email protected] , password = godaddy password , port : godaddy outgoing port .
Godaddy account
Our website hosted on godaddy with same name as domain.com
open relay not possible on emails.
Results
After setting alerts on SharePoint sites and assigning tasks with alerts we receive email in queue folder but they never get forwarded. We just wish to use any of our email *.domain.com to send outgoing emails from SharePoint . Its been a while we have no
success.
Tech Learner

Hi,
As I understand, you are using SharePoint 2013 integrating with third party SMTP server which provides email function.
From SharePoint side, I'd suggest you refer to the link below to configure email integration:
http://technet.microsoft.com/en-us/library/ee956941(v=office.15).aspx
If you have already confirm that message is sent from SharePoint, while stuck in queue on SMTP server, then the issue might be related to relay on SMTP server. Since the issue is related to third party product, we do not have enough resource here,
I'd recommend you contact their support engineer for more assistance:
https://support.godaddy.com/help/category/154/email
https://support.godaddy.com/help/article/3552/managing-your-email-account-smtp-relays
Thanks for the understanding.
Regards,
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected] .
Rebecca Tu
TechNet Community Support

Integration of ChaRM with third party tools

Hi all,
We are in the process of building the solution for Change Request Management implementation integrated with third party tool.
As the normal process for ChaRM is to work with the Service Desk functionality (to raise a ticket, then support message, change request, change document etc...), but what we need is create the change request, and change document directly with ChaRM without using the Service Desk functionality.
Did anybody come across this situation?
Please share your experience.
Thanks in advance.
Balaji

Hi Balaji,
there is no problem, as I understand, you want to use ChaRM without Service Desk. OK, than you create directly a Change Request in CRMD_ORDER, the transaction type you have to select is SDCR (standard transaction type), you have to approve it and then you can create a change document, it is not necessary that you start with a Service Desk ticket like SLFN.
You need configured TMS a SolMan Project with a Maintenance Cycle, thats it (but this is enough , don't forget the customizing).
I hope I understood you correct
Udo

Pairing AX with Third Party Router

Similar Messages

Maybe you are looking for