PAL - NTSC Conversion question

I have some PAL DV footage at 25fps which I need to convert to NTSC to match some existing NTSC footage. The NTSC originated footage, when played in Quicktime diisplays the following info:
FPS: 23.98
Playing FPS: 24
I need to convert the PAL footage to match the NTSC frame rates, annd also I'd like to converted footage to appear that it is NTSC roriginated (i'e, with the slower framerate as opposed to 25fps).
I've made a few tests using the Frame Controls "Set Duration" options in compressor, but the results always seem end up at the wrong frame rates. Which setting should use? And can somebody explain what all the settings mean?
24@25
23.98@24
23.98@25
[email protected]
29.97@30
[email protected]
Message was edited by: Marc Morris
Message was edited by: Marc Morris
Message was edited by: Marc Morris

Marc,
I dont have extensive knowledge in this area although am literally doing the same conversion (PAL to NTSC) on my mac as I type this.
I also recently read in Videography magazine about a project that was assembled from archived footage and all of the footage used originated from different formats and that was the hardest part about editing.
They mentioned all the different ways they attempted to convert the footage but in the end it seemed as if they just settled for what looked best because they couldnt get an exact conversion.
If your looking for a better way I would contact a transfer house to see what they may be capable of doing. Another thing worthy of pointing out that reading how they did the conversion they never mentioned using compressor so there are probably better systems at converting the files.
hopefully this helps.
-jeremywearsvans

Similar Messages

Problems with PAL/NTSC Conversion

I have a PAL Sony handycam camcorder and Final Cut Express HD installed on my 2004 iBook G4 (both purchased in North America, if that makes any difference)
- I capture both PAL recorded footage (from my camera) and NTSC recorded
footage (from other cameras) in Final Cut
- Whenever capturing I alter the settings in “Easy Setup” to “DV PAL
firewire basic” or “DV-NTSC Firewire Basic” depending on if I’m using PAL
or NTSC footage at the time
-After capturing, when I drag captured clips from the Browser window down
into the Sequence timeline, every clip has to be rendered in the timeline.
This is very time-consuming (rendering can take up to 10minutes for what
might be a 2minute clip); and this happens regardless of my “easy setup”
settings or the regional code of the footage.
-In addition, after a clip has been rendered once, and I then make an
alteration (usually a cut) the clip has be re-rendered
-Also – when PAL footage is rendered and then exported usually frames are
dropped and the image appears choppy.
- Furthermore (and I suspect this is related) the program will not print
to video; and I have tried using both PAL and NTSC cameras. Therefore I
have to export all projects as quicktime files and then burn DVDs.
- Any suggestions?
Thanks,
Marc Griffin

Hi(Bonjour)!
One important thing: FCE sequences's settings have to match your clip's settings.
If you mix PAL material in a NTSC sequence, your material will need rendering and vice versa.
Secondly: PAL format is a 25 FPS material, and NTSC is a 30 (29.97) one.
So when you convert PAL to NTSC, there is a frame rate mismatch, thus the choppy playback.
Your camcorder cannot record PAL material if it's a NTSC model. You need a plugin that converts PAL material to NTSC.
There is a nice plugin pack from Nattress that performs PAL to NTSC conversion with various pulldown options (ie scalling 30 fps to 24 fps by blending frames selectively).
See:
http://www.nattress.com/Products/standardsconversion/standardsconversion.htm
Final Cut Studio 2 (Final Cut Pro 6) will support multiple resolutions sequences (shipping in may), it's a new great feature.
Michel Boissonneault

FCPv2 and PAL-NTSC Conversions

Hello everyone,
I have just read a bit about FCPv2. I am really interested in being able to use PAL and NTSC in the same time line.
At the moment we send out footage out for a hardware standards conversion.
Does anyone know how this new feature is going to work? Will it be good, will it need rendering, will it allow me to out put to PAL or NTSC on my DVCAM Deck?
Any thoughts on this would be great.
Thanks,
David Lee

Anyone...? I need to know why US news editors in DC have had to use Procoder... Running Avid... to convert to PAL from NTSC, Then sending it on a FTP... To places like Norway, Denmark... While finalcut could not make the conversion. The question is, will the new Studio release let me use Finalcut without having to buy a dual core..?
I Edit in NTSC on my powerbook... then I need to transcode it to PAL (MPEG 4? I believe...) and then send it to the Server in Europe or Scandinavia?
This is why all the editors use AVID and not APPLE's finalcutpro.
Another words... Compressor the old version would not work. So people could not use Final Cut... Or just recently they had to buy the dualcore... then they would have to edit in Final cut... Open Pro-coder in a Windows PC partition.... Then drag the master in... Then export, back to final cut, (or do they send it from Procoder?) I don't know. I would rather upgrade to STUDIO then have to buy a new dualcore... Can the new studio do this? Sorry if I sound like a fool....
Thanks!
Powerbook G4 Mac OS X (10.4.9) final cut pro HD
G4 Mac OS X (10.4.3)
G4 Mac OS X (10.4.3)

PAL/NTSC conversion for DVDs

Hello All
I recently had some work involving standard conversion of DV PAL material and then burning said material onto DVD. Everybody trying it knows that this is time consuming and doesn't always produce the desired results - for obvious reasons (Methods used by me were the two documented on Dan Slagle's Unofficial iMovie FAQ).
I then had the really "fantastic" idea to tweak the DVD with myDVDedit, by simply setting the IFO parameters to NTSC 720x480. Tested the burned DVD on two different set-top NTSC DVD players - and discarded the whole thing as "silly BS"
Searching through the Net I just found out, that somebody had the same idea using IFOedit (the PC equivalent to myDVDedit) and that the results were mixed, but there were a lot of users that shouted: "great, this works".
Getting a bit confused now, as i had thought this over after my own experiment and had come to the conclusion that it couldn't possibly work.
Any insight would be greatly appreciated
viva la mela

Hi mish,
that is such a .. <searching correct english word> hillarious (?) idea, I give you a star for that ;-)))
changing some flags on a ready-made dvd... wow! nice try...- but as Fred said, NTSC<<>>PAL conversions are no trivial tasks... you run into many problems, e.g. where do you get the additonal 5 frames per second you need for a transfer from PAL to NTSC? how to make the audio fit to these new pictures? and, I HAVE to do this silly joke: NTSC has a very different color concept (Never The Same Color) then PAL.. and for sure a different res...
the name is irritating, but all mighty JES Deinterlacer is doing a fantastic job in converting video standards (ok, for a free software solution...) give that a try!

Pal-ntsc conversion via 23,98fs slow-pal technique

Hi to all,
I've been trying to convert a prores 1280x720 clip recorded at 25fs (for a pal output) into a ntsc compatible clip that will be used on an ntsc dvd and also for an ntsc h264 quicktime file.
I fell on an article explaining the "SLOW_PAL technique"(http://www.macworld.com/article/49306/2006/02/marchcreate.html) by converting the clip to 23,98fs in cinema tools before applying a 3:2 pulldown in FCP. The result is pretty stuning but my question is, once all this is done, i end up with a 23,98fs file.
Do i need to convert that into a 29,97 file to make sute it will work on an ntsc dvd plateform? If i do i lose all the smothness i just gained....
thanks in advance, and hope i'm clear....
tee.

No you don't need to convert to 29.97
export qt self contained current settings
drop that export into compressor and set up you DVD compression and your h264 compression
author the DVD in DVD Studio pro
the player will supply the pulldown
h264 will play fine on any device that will play h264

PAL NTSC conversion and downsizing form HD to standard

I have a project that I need to send off for 3 competitions in the next week one in Pal, one as a Mpeg NTSC and the third (preferably) as a NTSC .mov file. The project is made up of clips rendered in 3D and others shot in Sony Pal HD. I am rendering as standard size wide screen. The PAL is OK, but the NTSC version MPEG (I havent tired the mov file yet) that I made by nesting the PAL in a NTSC sequence, has unusual cool green colour shifts and flickering in WM or VCL media player that did not appear in my Premiere monitor, which was fine. The flickering is especially noticeable with time ramping (and some layering and keying.)
Is it possible to covert to NTSC in Premiere cs3, or do I need to send it to a service bureau? Does the downsizing to standard affect it as well?

Download the following:
1.)
hd2sd for AviSynth 2.5 <- unzip these files into your AviSynth/plugins folder
2.)
dv2film for AviSynth 2.5 <- unzip these files into your AviSynth/plugins folder
3.)
Lagarith lossless codec
HD PAL Timeline -> SD PAL .avi
Follow the steps outlined in
my guide but, instead of the sample script provided there, use this script template:
AviSource("c:/path_to/signpost.avi")
hd2sd(OutputColorSpace="YUY2", OutputBFF=true)
1.) Open the script file in VirtualDub
2.) Choose the Lagarith codec from the Compression menu
3.) Also select "Fast Recompress" from the Compression menu.
4.) Select "Save AVI" from the File menu
5.) This will result in a 720x576 interlaced (lower field first) file with lossless compression. Import this file into whatever program you like to convert to MPEG, Quicktime, DVD, etc.
HD PAL Timeline -> NTSC PAL .avi
AviSource("c:/path_to/signpost.avi")
dv60i50i(interlaced_out=false)
hd2sd(OutputColorSpace="YUY2", OutputBFF=true)
Repeat the steps above, saving this a lossless intermediary AVI file which you can then use to convert to whatever type of file you need.

PAL - NTSC for Japan

Hi all, I have a question that I hope someone can answer.
I've gotta shoot a few minutes if footage that a friend of mine is then taking to Japan and showing to
someone there. Now as far as I know they'll be watching in on a PC but Im gonna try give him as many format
variations as possible to be sure. So the queston is, f I'm shooting in standard miniDV PAL, what are the
best options for me in terms of encoding I should do, do I export as PAL MPEG 2 on DVD, what kind of
effect does the PAL->NTSC conversion have. Should I do a VideoCD version.
My plan is to to a NTSC DVD, and MPEG 1 & 4 version and maybe a few others. Does this sound good enough?
Thanks in advance
Declan

The OP said he thinks it will be played
on a computer but he wants to give as many options as
possible. . . I took that to mean he'd like it to be
watchable on TV in Japan if possible. He needs NTSC.
From the tone of the post I assumed, perhaps glibly, that this is not a life-threatening project. There was never mention of TV playback. But I take your point.
PAL to NTSC via Compressor . . . "successful" maybe
but read the posts on this forum to learn about the
quality! (I'd LOVE to be proved wrong
though)!
Oh, I hadn't seen those posts. I've only run a few small tests myself, but the results were excellent to my eye. This is the method I used:
http://www.macworld.com/2006/02/secrets/marchcreate/index.php?pf=1
What kind of problems have you seen? I've had a quick look back through a few threads and most of the issues I have seen would probably have been solved with a careful setup.
I'm sure Graeme Nattress's plugins are excellent, haven't used them. I've done most of my conversions to date in After Effects, also with good results.

Sharing movies overseas - PAL & NTSC burning

OK -
So apparently I have the option to burn a movie as NTSC or PAL.
So I have to assume that the region codes on my Superdrive only matter when there is a commerically sold protected disk being played.
Figuring out the best way to produce a home movie DVD to share with friends in Europe is still a problem.
I do know that apparently TV set-top DVD burners produce video disks which have no region code difficulties. Is this likewise true for movies edited in iMovie, Final Cut Express & burned via iDVD?
More information would help keep this from being a trial & error process - if the people on the other end are not overly technical. Its hard enough to get substantive "help desk-type" of feedback to even understand the nature of the problem your recipients might be experiencing.

Hi Ernest
I know all about the PAL/NTSC conversion because I, unlike you, live in a Pal area.
You are so lucky living in USA because NTSC is accepted in all areas. In fact even though I live in a PAL area, New Zealand all my DVD's produced for world sale are in the NTSC format. Virtually every DVD player accepts NTSC but unfortunatley for me the USA DVD players do notaccept Pal
So you can safely make and send all your DVD's in NTSC and they will be playable worldwide.
As I said I live in a PAL area. 25 frames per sec and I have to change my DVD programmes to NTSC approx 29 frames per second. To get an acceptable conversion can be either very expensive or time consuming.
I have not tried the Jes de interlacer so I cannot comment but most on the forum find it acceptable.
I found the problem was to get good quality on all formats, computer, tube and LCD and Plasma at an acceptable cost and did not tie up my computer for hours.
Eventually I managed to find out how to do it but it is a long job.
One would think that the answer would be to film in NTSC but one cannot do this in a PAL area because of the difference in the electricity voltage. If I used an NTSC camera under lamps here in NZ the pictures would be unusable and visa versa.
Nowadays all commercial DVD's are just dubbed in NTSC. This is a pity because PAL gives a better picture. In the trade NTSC used to be known as Never The Same Colour Twice.
Sometimes I wish I lived in the USA!
Hope this helps
Jane

PAL-NTSC questions

I have a lot of VHS-PAL tapes to commit to iMovie/iDVD5. I have transferred several using a Video Standards Converter (PAL to NTSC) and an Analog to Digital converter (set to NTSC). There were some artifacts in the final result that I did not like, so I removed the Standards converter and set the A/D device to PAL (rather than NTSC) and fed into iMovie/iDVD5. The results played perfectly on a Sony DVD player into CRT analog TVs with NO artifacts!
I am thinking of using this as standard practice because results are superior.
How is this method possible?
Does iMovie/iDVD5, or the Sony player throw away 100 scan lines and insert 5 fps?
Conversely will homegrown NTSC DVDs play on PAL players and PAL TVs?
Am I making a mistake for the future?
Will this work with the new Digital display TVs (Hi-Def)?
I would sincerely appreciate any enlightenment that the forum can offer on all my questions.
This is Posted on both iDVD and iMovie Forums for wider exposure
G4 Quicksilver Dual 1.0GHz: G3-400 B&W 768MB RAM Mac OS X (10.3.9)

Yes, you can convert PAL<->NTSC via iDVD/iMovie/QT
but the results are not very good because the
movement gets jerky because frames are just dropped
or duplicated to compensate the different
framerates.
I guess iDVD did the conversion in your case because
apparently you left its prefs at NTSC.
You get smoother motion with JES Deinterlacer:
http://www.sjoki.uta.fi/~shmhav/SVCDon_aMacintosh.ht
ml#PAL_NTSC
http://www.danslagle.com/mac/iMovie/tips_tricks/6017.s
html
Dear Matti: You were perfectly correct in your analysis as to what transpired. Your answer and the valuable links help me a lot and are sincerely appreciated.
One further question, however: How long does the JES DeInterlacer take to convert 1 minute if iMovie from PAL to NTSC?
Thanks again
Malcolm
G4 Quicksilver Dual 1.0GHz: G3-400 B&W 768MB RAM Mac OS X (10.3.9)

PAL to NTSC conversion

Hi
I tried using compressor to do a PAL to NTSC conversion on a completed project, but found it pixelated all still photos and graphics in my project. It was also going to take 18 hrs (macbook pro 2.4ghz)
So I have tried using JES deinterlacer.
I've done a couple of tests using Jes Deinterlacer to convert PAL to NTSC and below are the results:
Test1 - default settings, dvd came out with some minimal artifacts every fourth frame, but only in certain shots.
Test2 - reinterlace chroma option, no real difference to default settings, still minimal artifacts every fourth frame in certain shots
Test3 - reinterlace chroma option, progressive out and telecine instead of blend, this option appear to increase artifact pulsing, in certain shots.
Decided to go with default settings as no improvement of fourth frame pulsing in reinterlace chroma option test.
Unfortunately my project (75 mins long) still had artifact pulsing which appeared to get worst as the dvd got closer the end of the program. I can't work out why certain shots appear fine while others have this pulsing effect.
Really not sure what to do now, any suggestions?

http://www.sjoki.uta.fi/~shmhav/SVCDon_a_Macintosh.html#PALNTSC
http://www.danslagle.com/mac/iMovie/tips_tricks/6017.shtml

PAL to NTSC conversion house in OC

Hi,
Does anyone know a good post house that has PAL to NTSC conversion service in ORANGE COUNTY, Ca?
our source would be in DBeta Uncompress format. Was thinking of sending them uncompress 10bit QT file so we don't have to edit out to Dbeta tape.
thank you so much,
JP

point 360 is the best house in burbank

Vertical Black Lines on edges after 4:3 PAL - 4:3 NTSC conversion

I hate to cross post - but few people seem to use the Compressor Forum and there's been zero response.
. . . and once you guys in the US go to beddy-bies, I'll lose another day with the time-lag!
Can anyone come up with a cure for this little PAL - NTSC problem?
http://discussions.apple.com/thread.jspa?threadID=580170&tstart=0
Andy
G5 Quad. 8 GB. 250 & 500 GB Internal HDs. G-Tech G-Raid 1 TB. FCP 5.0.4 (Studio) Mac OS X (10.4.7) Sony HVR-Z1E.
You can't educate pork . . ..

> My other thought would be it is a scaling issue.
Going from 576 vertical pixels to 480 vertical
pixels will involve scaling the video
Of COURSE . . . !
Thanks for the tip, Trevor - when I read that, I compared the equivalent still from the PAL footage and realised the NTSC clip was squeezed!
I went through the Inspector settings and Constrain to Display Aspect was set to NONE. I've set this to 4:3 and it's cooking as I type . . .
>I have produced NTSC DVDs from PAL source by creating a PAL
DVD in DVDSP, duplicating the project, deleting the
media, changing the project to NTSC and reimporting
the media. Encoding was done in DVDSP and the
results were fine for our purpose.
Not heard of this one - but I'll certainly try it when I get a chance. I strongly recommend Hanumang's recipe though - the quality's excellent.
But you need plenty of processor power. An 80 min movie I processed some weeks ago (chapter by chapter) took several days and nights - even on the Quad G5.
I feel it's well worth it though - and I can get on with other work (Photoshop, Word, Internet etc) while it's processing. FCP seems to be one of the few things you can't use while Compressor is working.
I'll post back when I have the result of my latest Compressor test.
Andy
G5 Quad. 8 GB. 250 & 500 GB Internal HDs. G-Tech G-Raid 1 TB. FCP 5.0.4 (Studio) Mac OS X (10.4.7) Sony HVR-Z1E.
You can't educate pork . . ..

Where to ask conversion question

I want to ask a question about PAL to NTSC conversion. What's the right forum for that? Is there one? Should I ask here?,
Ross

My recommendation -
Using MPEG Streamclip, convert the PAL DVD to QuickTime/Apple DV PAL.
In FCE, change your Easy Setup to DV PAL; create a new sequence; import the QuickTime/Apple DV PAL file you exported from MPEG Streamclip. Do your editing (if any). Export to QuickTime Movie. Non-self contained is fine.
In iDVD, set your Projects > Video Mode preference to NTSC, with encoding = High Quality or Professional Quality. Import the QT Movie that you exported from FCE. Create whatever menus you want. Burn your DVD. You will get an NTSC DVD that will play just fine in most USA DVD players. I have done this and think the resulting quality is pretty good.
iDVD has the capability to convert PAL>NTSC and NTSC>PAL. I have experimented with this and think the quality is quite good.
There are more complex ways to convert between PAL and NTSC. JES Deinterlacer has the capability but I think other methods produce better results. The iDVD method is basically free. The only better alternative that I have experience with is Graeme Nattress' Standards Conversion, which works really well but it costs $100 and because it was designed for FCPro, it requires some workarounds to use in FCE.

IDVD - PAL - NTSC - REGIONS; All messed up?

So I finished a project on iDVD, and the "clients" are from many different countries... The original project was worked as PAL. In the end, in iDVD I changed the setting to NTSC in order to write 3 disks. 1 for a client in Canada, and 2 for the U.S.
With the Canadian, there were no issues (at least the client didn't mention anything, only that the DVDs were great).
The one American, told me she had to change regions to her laptop DVD in order to watch it, but other than that it was ok.
The other American, could not watch the DVDs on her old windows xp laptop, also not on her DVD player on her Tv. She also went to a store to ask for help and the technician told her he could see the contents of the disk, but not play them; probably because they were not NTSC (!!!!). Finally she watched the DVDs by using VLC on her laptop (no region change here...)
What is going on? The same disks, 3 totally different behaviours...
Can anyone guess what went wrong?
I would really like to fix those problems...
Thank you!

Hi
Region - Should not be any problem - as iDVD only can make Region = Zero (0)
This means - Plays in any economical region (Has Nothing to do With TV-Standard at all)
TV-standard are as:
• NTSC (29.97fps) 520 lines - about 640x480 pixels (square) 720x480 rectangular (narrow) pixels
• PAL (25 fps) 625 lines - about 768x576 pixels (square) 720x576 rectangular (narrow) pixels
And Playback on Computer - should be able to use both - VLC usually works better than QuickTime in these cases. BUT here I noticed that PC/Macs are picky on Quality
• Burn speed I set down to x2 (or x4)
• I only use Verbatim DVDs - NO Memorex or NoName or other cheap brands - Yes it matters
• I use DVD-R as they play on more and even older DVD-players
My notes on this subject.
PAL to NTSC or NTSC to PAL
A. Copying commercial DVDs - No Not possibly at all - Not even legal to discuss.
B. Home made DVDs (DVDs without copy protection)
C. Movies from iMovie or FinalCut
• Save as full quality QuickTime .mov and convert this with JES_Deinterlacer (free on internet)
NTSC ---> PAL.
• Most often not necessary - Most stand alone PAL DVD-players playback NTSC
(if TV is old in BL/W)
PAL ---> NTSC.
• If played on Mac - not necessary AT ALL
• If on NTSC DVD-player - CONVERSION IS NEEDED - nearly no Stand alone NTSC-DVD-players
playback PAL at all.
To do this You need to convert the PAL DVD to streaming.DV or full quality QuickTime .mov
• I use Roxio Toast™ to do this (There are no free converter)
• JES_Deinterlacer (free on internet) to convert to NTSC
• Set up an NTSC project (29.97fps or 30) in iDVD and import then burn
I burn to
• Verbatim DVD-R
• Set down burn speed in iDVD to x1 or x4 recommended by many
• Secure a minimum of 25Gb free space on internal boot hard disk before burning (IMPORTANT)
PAL is 25 fps and an analog TV standard of 625 lines
NTSC is 29.97 fps and 520 lines
NTSC (29.97fps) 520 lines - about 640x480 pixels (square) 720x480 rectangular (narrow) pixels
PAL (25 fps) 625 lines - about 768x576 pixels (square) 720x576 rectangular (narrow) pixels
to use a photo 702x480 resp 576 then add 9 pixels on each side to add together as 720
If iDVD hangs on PAL or NTSC.
Bengt W wrote
Deleting iDVD pref. file - should return You into NTSC mode.
Yes iDVD can switch to PAL - BUT as You see with a rather lousy result.
a. Need to convert to PAL - most often not - Most PAL-player can playback NTSC
and on a fairly new TV in color. (old TV in Bl/W)
(Other way around - from PAL to NTSC most often a must - few NTSC-player can use PAL)
b. IF MUST - then use JES_Deinterlacer to do this conversion - so much better and free.
My list on this (or rather PAL --> NTSC - just think the other way around)
I have to send it overseas
That too can be a problem. As USA = NTSC = 29.97fps and EU = PAL = 25fps.
DO Not let iMovie or iDVD do this conversion from one to the other - Result will be Very
BAD
I save the movie as a full quality QuickTime .mov file then I use JES_Deinterlacer to do the conversion - then I cont. in iMovie or iDVD with project set accordingly.
JES_Deinterlacer is free on Internet and there are Pro applications but not that much better and costs are astronomical.
PAL-DVDs - don't play in US
NTSC-DVDs - usually plays well in EU
All plays well on a Mac - What ever.
Allosaurus writes
Thank you SDMacuser. I dumped all the plist icons with no result, and was getting pretty plist off when it occurred to me to delete all the previous dvd.proj files. Bingo. That did the trick. So thank you for all your help and the additional information you provided.
Yours Bengt W

PAL - NTSC, Looks fine on comp, bad on TV

Hi All,
My Setup: Quad G5, 2.5ghz, 4.5GB ram, Final Cut Studio (all versions completely up to date)
I know there are a million issues in converting PAL -> NTSC, but I was hoping someone could possibly give me a direction to start looking..
I used Nattress filters to convert PAL timeline footage to NTSC. I burned a DVD and it looks really good on my computer. Then when i play it on a TV, the motion is TERRIBLE. Like it is jumpy and has trails everywhere.
What types of settings or issues could be causing the significant discrepancy between what the converted footage looks like on comp versus TV? I know that square/rectangle pixels are an issue, but I wonder if this goes beyond that? It doesn't seem to be just an aspect issue, but I could be wrong...
Thanks in advance,
Jason

Hi:
I found a good preset settings to use with Compressor in an old thread from Hanumang (I cabbot find now the link, sorry).
Start with the standard NTSC preset in Compressor, in the group Advanced Format Conversion and check from the following list and change appropiates settings (is a copy of my custom PAL to NTSC preset):
========================
Name: DV NTSC Conversion Hanumag
Description: DV/DVCam NTSC with 48kHz stereo audio
File Extension: mov
Audio Encoder
16-bit Integer (Big Endian), Stereo (L R), 48,000 kHz
Video Encoder
Format: QT
Width: 720
Height: 480
Pixel aspect ratio: NTSC CCIR 601/DV
Crop: None
Frame rate: 29.97
Frame Controls:
Retiming: Motion Compensated
Resize Filter: Linear Filter
Deinterlace Filter: Motion Adaptive
Adaptive Details: On
Antialias: 0
Detail Level: 0
Field Output: Bottom Field First
Codec Type: DV/DVCPRO - NTSC
Multi-pass: Off, frame reorder: Off
Scan Mode: Interlaced
Aspect Ratio: 4:3
Pixel depth: 24
Spatial quality: 99
Min. Spatial quality: 50
Temporal quality: 0
Min. temporal quality: 50
========================
Make a short test and compare with your previous results. The encoding is quite slow, but you get very good results (and it's free).
Hope that helps !
Alberto

PAL - NTSC Conversion question

Similar Messages

Maybe you are looking for