Panasonic PV-GS29 DV Won't Be Recognized

Hi Gang
I picked up a Panasonic PV-GS29 - like new condition - was going to use it as a playback deck. It works well, but can't be recognized thru FC6 - tried 2 different DV cables - 2 different FW400 ports - tried all combinations of 'Easy Set Up'.
No Go
Maybe the PV-GS29 is just too basic, not enough settings to be configured properly?
Any ideas?
Thanx
Mike

Hi Ian
Yes understood - I like the mechanics - I noticed the toggle wheel is firm and the mechanics are sound. It's a shame because this would have taken some wear and tear off my DVX100B's.
Unless I've missed something here; the cables I've been trying are standard IEEE 1394. Unless Panasonic has a special FW cable? Unfortunately, it looks like a bad FW port
Ian when you have a few moments for a download, look on page 55-66; http://service.us.panasonic.com/OPERMANPDF/PVGS29.PDF
Thank you Ian
Mike
Mike

Similar Messages

I got a new laptop and installed iTunes and plugged in my iPod but it won't get recognized on iTunes or in my computer, the computer says unknown device found and that the software was not successfully installed.

I got a new laptop and installed iTunes and plugged in my iPod but it won't get recognized on iTunes or in my computer, the computer says unknown device found and that the software was not successfully installed. What shall I do ? I tried reinstalling so many times and everything else I could find. Please help!

Hello MArk.wijesinghe,
Thanks for using Apple Support Communities.
For more information on this, take a look at this article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Best of luck,
Mario

Camera Raw CS4 5.2 Update/Panasonic LX5 .RW2 Files Won't Open

Hi, recently purchased a Panasonic LX5 that shoots raw using the .rw2 extension. Tried importing into Camera Raw via Bridge, but couldn't get it to open. Read around and discovered that Raw needs to be manually updated to 5.2 and some profiles need to be installed (which I've done). Went to the Adobe download section and followed the directions for installing on a mac (OS 10.6.8) - when I open up other files it reads Camera Raw 5.2 at the top. However, the Panasonic LX5 files still won't open. Did some more searching and I've read that everything from the "files will open without problem" to "they need to be converted using a .DNG converter." So, I'm confused; am I doing something wrong? Is there an additional step I'm missing to the 5.2 update? Do I just need to download the .DNG converter and use that? Any help is appreciated.
I'm on:
Mac 10.6.8
Running CS4

You should probably update all the way to Camera Raw 5.7, which was the latest update for Photoshop CS4.
-Noel

Canon MP180 scanner won't be recognized after Mavericks upgrade

Dear Apple Support Communities members,
My Canon MP180 scanner won't be recognized after Mac OS X 10.9 (Mavericks) upgrade: neither in Image Capture nor in MP180 standalone app.
The printer works well though.
Any idea?
Thanks a lot.
Best wishes,
Yves

Well...
I asked Canon support and got the answer that OS X 10.9 (Mavericks) was not supported.
I am kindly being suggested either to downgrade from 10.9 or to buy another scanner. Cool.

Help! Returned ipod won't be recognized

I updated itunes, updated the ipod.
my ipod crashed before. i sent it back to be repaired and got a new one. so this one won't be recognized.

I have the same problem.. returned ipod is MAc enabled and BUT it wont restore!!
My new ipod is not being recognised on my pc.
I have:
Reintstalled the latest Ipod Sw 2005-26-6 (and the original version 2004 8-6)when the latest load didnt work. reinstalled iTunes and tried to restore my ipod.. when i do, i have a pop up that says that the ipod is locked!!. I have gone on the apple support website and it tells me to format my ipod for windows i need "iPod for Windows Software 1.0" but the website also states that this Sw cannot be found on the Apple website! The original packaging (for my last ipod) only had the one disc with itunes and ipod sw updater (no specfic Windows sw)... Before anyone says what i expect them to say..even if this sw is on the original CD.. it wont connect to my laptop as its formatted for a mac!! Im going on holiday in two days....
HElp

Nikon Coolscan LS 2000 won't be recognized bij Classic

When I want to work in Classic the Nikon LS 2000 scanner won't be recognized under Photoshop 6.(it has a SCSI-connection; the Umax-scanner has a USB and is recognized for sure). Is there any solution for this problem(Nikon says not, but I wont give up) I tried Vuescan but I don't like the program because its totally different. Anyone??

Take a look at the Nikon Coolscan User's Group Discussion
http://www.flickr.com/groups/74221125@N00/discuss/72157624196874277
Two options that you might find useful are Silverfast http://www.silverfast.com/show/scanners-nikon/en.html and VueScan http://www.hamrick.com/
Silverfast will handle dust removal.
Silverfast is somewhat expensive, and VueScan is under $100.

Okay so my iPhone randomly shut off for NO reason at all. At 30% and everything. Now it won't turn on, won't charge, and won't be recognized on the computer. Help me?

I was cleaning, and had replied to a message before setting it down. I go back to check it about ten minutes later, and its just off. It will not turn on for anything, won't be recognized, and won't recognize the charger. Idk what to do. Help me?

If the battery is completely dead it may take some time before there is enough power in the battery to display even the rudimentary battery dead icon. Leave it charge over night. Still dead in the morning, take it to an Apple Store.

My new Apple TV won't be recognized by my IPhone Air-Play. I made sure the home sharing is on and that both Devises are I the same network..

My new Apple TV won't be recognized by my IPhone Air-Play. I made sure the home sharing is on and that both Devises are I the same network. The IPhone see the other two Apple TVs at my house, but for some reason it won't see the third one I just added.

Check to see if AirPlay is actually turned on. (in Settings on the ATV)
Also, make sure it's not sitting directly next to your router; interference

My iphone 5s quick charges on my laptop and other computers but it won't get recognized by any of them or itunes

I have literally tried everything on several articles. I have 2 cables and I tried plugging my phone in with both of them but all it does is charge. My device isn't showing up on my computer. I thought it was the cables but I tried plugging in my sister's same exact phone and hers was recognized. I've uninstalled and reinstalled Itunes, several times, I've updated my computer, turned it off and on and done the same thing with my phone and I reset the settings on my phone as well. I've checked my device manager and the apple one doesn't show up, I've read the article for the support on how to make it show up but it still doesn't work. My phone charges it just won't sync and its not recognized by any computer and I don't know how to fix it.

Do you have the latest version of iTunes on your computer? It must be either v 11.x or 12.x. The fact that it charges means that the driver is installed. Have you checked that AppleMobileDeviceService.exe is running in Task Manager?
When you removed and reinstalled iTunes did you use these instructions? - Removing and Reinstalling iTunes

Ipod seen as a digital camera, and won't be recognized by Itunes.

Have: Ipod 2nd Generation (2.2.1), Windows Vista, Itunes Ver. 8.1
Problem: Alright here it is, my Ipod and my sister's is not being recognized by Itunes. It is however recognized by my computer as a digital camera. If I shutdown my computer and then plug in my Ipod while its off into the computer while its turning on its recognized. However, it won't sync saying "the ipod cannot be synced. the disk could not be read from or written to." Now it trys to sync but my Ipod doesn't have syncing on the screen. My Ipod though will be recognized by other computers.
Things I tried: All the steps on the apple page, please don't link me to the instructions again. I have uninstalled and installed Itunes soo mny times. Tried restoring it also, but couldn't finish the restore on my computer and had to use another one. Also I have tried plugging it in and out, using differant usb ports, pretty much everything with no success.
PLEASE HELP!!!

Welcome to Apple Discussions
I know it is your first post so I'll offer a gentle reminder to start new problems as new posts and not hijack an existing thread. Your problem is different than the OP.
In your case, you need to disable the automatic camera notification. The help article how to that is here: http://support.apple.com/kb/TS1857
The crashing part can be caused by an obsolete/incompatible driver on your PC. You will have to figure out how to update it so it doesn't crash or remove it entirely.

My iPod touch won't be recognized by my macbook.

I plugged in my iPod touch to my macbook this morning and it doesn't even charge. To make sure it wasn't the cable or the USB port, I plugged another USB and it was working fine. It won't appear on either iTunes or Finder. I found a solution that was intall all your updates and then restart your computer but still didn't work.
Any suggestions?
Thanks!

See:
iOS: Device not recognized in iTunes for Mac OS X
An iPod (and other similar devices) do not appear in Finder on a Mac

HT1349 my IPOD touch won't be recognized by my DELL Latitude PC and it won't synch. I'm technologically handicapped but all I know is it used to synch whenever I would attach it to computer with USB. Aside from tossing my DELL can anyone help?

My IPOD Touch isn't being recognized by my PC(DELL LatitudeD630) and it won't synch. I'm "technologically handicapped" but all I know is it used to synch whenever I would attach it to PC with USB cable. Aside from tossing my DELL can anyone offer suggestions that might solve this problem ? Thanks

I had this issue, I fixed it by going to:
Start > Control Panel > Devices and Printers
Then find the iPod, and Right Click > Properties > Hardware > Properties > Driver > Update Driver > Update Automatically
The driver had not been automatically installed, and windows found and installed the driver files for me. Took ~90 seconds, and then the iPod began it's sync process almost immediately after. Hope this helps anyone with the same issue! I'd try this before re-installing iTunes.

Panasonic KX-p7105 printer won't work on new mac - has disk for Mac OS 9.2

I finally switched to a Mac and am so disappointed that my great laser printer won't work. It prints pages of gibberish. My driver disk is for an older version of mac and won't open. I get a message saying "You can't open the network setup tool because the classic environment is no longer supported." I've since searched the net for drivers and can only find windows versions. Is this hopeless? Should I return my Mac (I'm still within the 14 days and don't want to buy another laser printer).
Any options?

Here's what John was talking about:
http://openprinting.org/show_printer.cgi?recnum=Panasonic-KX-P7105
You need the 3-part hpijs driver:
http://www.linuxfoundation.org/en/OpenPrinting/MacOSX/hpijs
(these are standard Mac installers - .dmg disk image files)

Backup/Copied Photos won't be recognized or imported into iPhoto library

I recently backup all data to usb hard disk and do a fresh installation of 10.6, and I accidentally create a whole new account w/ different user name (and I don't know whether it might cause any of my problems).
After I copied all my data backup, everything is so OK except all my pictures (jpg files mostly) in ~/Pictures folder won't be recognizable either by quicklook, preview or iPhoto. Also all my 14G iPhoto Library won't work. The files are still here but it just become not recognizable, can not be opened or imported into iPhoto. It told me that "the file is in an unrecognized format", but how could a jpg format not recognized by a MAC?
I updated iLife & iPhoto to latest version, and rebooted my laptop, but nothing changed. I know there might be chances that my pictures got damaged during transferring from hard disk to usb disk, but isn't it too weird that as I drag all my documents, movies, music and pictures at the same time all other files remained unchanged yet ALL my photos (including iPhoto Library) just all of sudden crashed together at the same time?
I am exhausted and can not figure out any posible reason, and would be very appreciated that if someone might suggest any methods, maybe even a clue. plz, plz, plz.........
Message was edited by: Kelip

if I directly double click "iPhoto Library" (which has a plain text like icon preview, not so colorful iphoto library style...), it tells me I should choose the app I wanna open it. After iPhoto chosen and opened, nothing happened, no photos in iPhoto main windows (events, faces, ..., all empty).
I aslo try "show package contents" and locate the exact photos' location in "iPhoto Library", which I believed should be in "iPhoto Library/Original/", all the photos in there could not be quicklook, opened by preview, Photoshop, etc. And the error msg says something like "format unrecognized" stuffs
Message was edited by: Kelip

Nokia 5200 won't be recognized

Hello,
I bought a Nokia 5200 and installed PC Suite 6.83.14.1.
It used to work fine in all the connection modes, but recently it hasn't recognized the phone in "Nokia PC Suite Mode" - only in mass storage and imaging (like a digital camera).
When I chose one of those methods, PC Suite says "Nokia 5200 connected in the wrong mode". If I change the mode to "PC Suite", the device manager will load up a bunch of drivers, but PC Suite won't recognize the phone anymore.
It states "No phone connected".
I tried reinstalling it and it worked once. Now, reinstalling or uninstalling/installing again won't make any difference.
Tried to remove all of Nokia's SDKs, cable drivers and all I could find from Nokia, but nothing works.
Also, it won't find the phone via IrDA nor Bluetooth.
Using XP Pro SP2.
My system info (portuguese, sorry):
Sistema operacional:
Microsoft Windows XP
Compilação 2600
Service Pack 2
Idioma: English
Idioma para programas não-Unicode: Português
Variante: Português
Idioma de entrada: Português
PC Suite Nokia:
Versão 6.83.14.1
Idioma: Português
Connectivity Cable Drivers:
Versão 6.83.9.0
PC Connectivity Solution:
Versão 7.7.10.0
Microsoft Outlook:
Versão 11.0
Compilação 5510
Pilha Bluetooth:
IVT pilha Bluetooth
Versão Install
Compilação
Thank you all in advance.

Ok, it's working now.
Here's more or less what I did:
Uninstalled iTunes (just for the record, since I installed it more or less at the same period PC Suite started to get moody).
Uninstalled PC Suite.
Uninstalled Cable drivers.
(At this point I tried to run "PC Suite Cleaner", but it said it wasn't compatible with this version of my PC Suite).
Then I hit CTRL+ALT+DEL and noticed "nsl_host_something.exe" was running. Searched for it and I found a big folder at %Program Files%\Common Files\Nokia". I deleted this whole folder and rebooted.
Installed PC Suite (which installs cable drivers automatically).
Tried to check for the cable connection (fired PC Suite, clicked 'Manage Connections'. This wouldn't list any type of connection.
Fired up PC Suite's installer and told it to 'repair'.
Launched PC Suite again, clicked on the connections button, selected cable, hit next and when it was looking for the phone, I connected it. Voilà!
Hope this helps somebody.
Cheers!

Panasonic PV-GS29 DV Won't Be Recognized

Similar Messages

Maybe you are looking for