Pange Extender Makes HH5 Reset Continuously

I have added a wireless range extender, (TP-Link TL-WA830RE v1.00), to my set up. When used as an extra access point this works fine, but it is annoying to keep switching portable devices between the TP-Link and the HomeHub5 when moving around the house.
I decided to change the TP-Link to "Range Extender" mode to avoid this regular changing, but in this mode the HH5 keeps resetting itself every couple of minutes or so. It goes through the full cycle - as if it was being repowered. But switch off the TP-Link or change it back to "Access Point" mode and all is well again.
Does anyone know why this is happening, or if there is a setting in either device that will prevent it?
TIA Paul

That is how I originally had the two set up: same SSID, wireless key and channel; but the magazine article I got that trick from said that I should hide the SSID on the TP-Link - do you know if that is correct or not?
I haven't tried different channels yet - I'm currently on channel 13 to reduce interference with the neighbours though the problems don't appear to be related to a particular channel.
I'm intrigued as to why the TP-Link causes the HH5 to continuously reset though. Any ideas anyone?
TIA, Paul.

Similar Messages

Is there a way to make the audio continue when the page is turned?

Can I make the audio continue while a reader turns pages in iBook? With everything I've tried the music shuts off as soon as the page is turned. Thanks for any insight.
a1foster

Latest: Working in Pages actually seems to work for this! Place the audio file in Pages (drag and drop works just fine), make sure the audio is inline (not floating) export Pages to ePub and run the Book Proofer . . . once you click to start the audio, the audio plays until the end, regardless of where you are in the book, it keeps playing. Minor victory because you loose a bit of the layout features that iBook Author has, but the audio now functions the way I was hoping.

How to make a RESET button in labview ?

how to make a RESET button in labview which resets all the elements in an array back to inactive element. Rather than deleting values in every column of array its better to create a RESET button ... how to make it ???

abhinavb wrote:
how to make a RESET button in labview which resets all the elements in an array back to inactive element. Rather than deleting values in every column of array its better to create a RESET button ... how to make it ???
You seem to have some misconceptions.
Is the array a control or an indicator or just some data held in a shift register or feedback node?
What you are probably looking for is an empty array. An empty array has a size of zero and has no elements (active or inactive). From your mentioning of "rows", you seem to have a 2D array.
The size of the array is independent of the visible size of the container.
Clearing an array means simply writing an empty array of the same datatype to it's terminal (or internal data structure). If the array is a control, you need to write to a local variable of it instead.
Can you show us some code so we can have a better understanding what exactly you mean by "array" in this context? Thanks!
LabVIEW Champion . Do more with less code and in less time .

In Pages, is it possible to make a page continuous?

Hi, folks!
So I'm working with Pages 5.2.2 and I need to make a page continuous. What I mean is that I don't want Pages to separate the pages as I keep writing, imagine it as one big scroll of paper. Is that possible?
Thanks!

Pages does what it says, uses pages.
You can change the pages to be very long though by having a custom page size in Menu > File > Page Setup…
Or simply use any of the dozens of alternatives more suitable to the task than Pages. Including TextEdit.
Peter

Can I make a button not make a slide continue?

Hi.
I looked for this question, but could not find an answer, so I'm hoping I'm re-posting something already answered. If so, I will accept my verbal chasisement.
Anyway...
I am attemping to create a "click and reveal' type interaction in Captivate 4 using buttons and hiding/unhiding objects. Essentially, when the user clicks button A, it will reveal image A and Caption A . When they click button B, through the magic of multiple actions, image A and Caption A will disappear and image B and Caption B will appear....etc. These buttons are at about 5 or so seconds into the timeline.
Around 28 seconds into the slide timeline, I have a "Back" and "Next" button that I use for user navigation instead of using the navigation buttons on the skin. This will pause the slide until the user clicks one of them to be navigated to the next slide or previous slide.
The problem I am running into is that if the user "lingers" on the slide and clicks back and forth between buttons A, B, C, etc. to re-look at all the objects, clicking on any of those buttons will continue the slide which is paused by the "Back and Next" buttons at the end of the timeline. Try as I might, I just can't make the slide pause and wait until the user actually clicks the "Next" or "Back" buttons when I click buttons A, B, and C over and over to re-look at the images and captions.
So is there any way to tell a button NOT to continue the slide? I want my buttons A, B, and C to do the multiple actions i have assigned them (show and hide objects) but do NOT want them to make the slide continue at the pause implemented by my navigation buttons.
Thoughts?
Thanks.
Rob

Hi there
Actually I do believe there is a way to make the behavior what you want. But I'll address your issue for making things known to Adobe first. Adobe has something called the "Wish Form/Bug Reporting Form" that they monitor. So you use that. (Link to that is in my sig line)
As for the button issue, you can accomplish it using Advanced Actions. What you need to do is to manipulate the Playhead to keep it paused. One way is by configuring the variable rdcmndGotoFrame with the value rdinfoCurrentFrame. Sometimes this works to just keep the playhead paused. Other times I've tried to do it with some success by repositioning the playhead farther upstream and allowing it to "float" back to the pause point of the object. And to do this you use the variable rdcmndGotoFrameAndResume and assigning it the frame number earlier in time. Of course, to do this you must first calculate the frame number to position at. I normally did this by inserting a Text Caption configured to present the rdinfoCurrentFrame variable and manipulating the pause points using a Click Box object to arrive at the desired value.
Cheers... Rick
Helpful and Handy Links
Captivate Wish Form/Bug Reporting Form
Adobe Certified Captivate Training
SorcerStone Blog
Captivate eBooks

How can i make factory reset to may macbook pro

hey, how can i make factory reset to my macbook pro

Throw away any files which may contain sensitive data and securely empty the Trash.
If it shipped with Mac OS X 10.6.8 or earlier, insert its original disk and restart the computer with the C key held down.
If it shipped with Mac OS X 10.7 or newer, restart with the Command and R keys held down.
Use the Disk Utility to erase the partition with Mac OS X installed, and then install a new OS onto it. If you used a disk and are going to sell or give away the computer, include the disk with it.
(96703)

Equium A200 - Can't make password reset disk on CD

W/Vista, Pioneer DVD-RW
Can't make password reset disk on CD, all I get is - This feature requires removable media, such as floppy drive or USB flash drive.
Are CD's or DVD's not classed as removable media now?
In help and support it states - you'll need _removable media_ such as a USB flash drive or _CD_..
Any help on this would be appreciated.

Are CD's or DVD's not classed as removable media now?
In my opinion it is the question for Microsoft because you try to use Vista feature and, as far as I know, notebook manufacturers have nothing to do with it.
To be honest for me it is pretty logic. If you want to use such disc it should be small and compact. The best disc for these purposes is USB memory stick. You can put it in every pocket and have with you.
In my opinion CD media is not so adequate for this. What you think about it?

My ipad makes me reset my password almost every week...what is the problem?

My ipad2 makes me reset my password almost every week. I don't get it!
Arna

Do you have your iPad configured to get your work email through an Exchange server? The server adminstrator my be enforcing a passcode.

How can I make podcasts play continuously. And Why do I have to sign in to itunes twice every time I open it?

How can I make podcasts play continuously. And Why do I have to sign in to itunes twice every time I open it?

its really annoying since nobody uses my computer and its password protected.... But like sometimes it does happen where i have to put it in, and other times it doesn't

HH5 reset.. many many times!.

My HH5 keeps reseting, infact 4 times since I came home from work at 5. Below are my stats lines 1-13 and I have performed a quiet line test. It dropped out a few times last night and approx 2 other days this week.
I can tell when its happend as I use unblock us and netflix, when the router reconnects I get a new IP and have to log into the website to accept the IP change before I can continue watching whatever it is.
Can I get some mod help please if possible.
1. Product name:
BT Home Hub
2. Serial number:
+068343+NQ41741545
3. Firmware version:
Software version 4.7.5.1.83.8.204 (Type A) Last updated 14/01/15
4. Board version:
BT Hub 5A
5. DSL uptime:
0 days, 00:07:48
6. Data rate:
19999 / 79995
7. Maximum data rate:
32406 / 80836
8. Noise margin:
15.2 / 6.9
9. Line attenuation:
15.8 / 14.2
10. Signal attenuation:
15.9 / 14.2
11. Data sent/received:
1.4 MB / 11.6 MB
12. Broadband username:
[email protected]
13. BT Wi-fi:
Yes

Following the latest reset... 3rd time this morning this is from the hub manager.
197.510000) CWMP: session completed successfully
11:44:10, 08 Feb.
( 196.860000) CWMP: HTTP authentication success from https://pbthdm.bt.mo
11:44:08, 08 Feb.
( 195.430000) CWMP: Server URL: https://pbthdm.bt.mo; Connecting as user: ACS username
11:44:08, 08 Feb.
( 195.420000) CWMP: Session start now. Event code(s): '4 VALUE CHANGE'
11:44:08, 08 Feb.
( 195.020000) CWMP: Initializing transaction for event code 4 VALUE CHANGE
11:43:54, 08 Feb.
( 181.430000) CWMP: session completed successfully
11:43:53, 08 Feb.
( 180.400000) CWMP: HTTP authentication success from https://pbthdm.bt.mo
12:43:21, 08 Feb.
( 164.660000) CWMP: Server URL: https://pbthdm.bt.mo; Connecting as user: ACS username
12:43:21, 08 Feb.
( 164.650000) CWMP: Session start now. Event code(s): '1 BOOT,4 VALUE

How to make hard reset on laserjet pro mfp m125rnw

Hi, All
I need some help. Cause of my ugly hands I install chineese language on my printer How can i make the hard reset to reset the language settings?
Thanks
This question was solved.
View Solution.

Also you may want to try.
Turn off the device.
Press and hold the Copy+ Cancel (X) button, keep the quadrant depressed as you turn the product on.
When the ‘Permanent Storage Init.’ Message appears on the display, release the button.
Super NVRAM Initialize
Turn off the device.
Press and hold the Right+ Cancel (X) button, keep the quadrant depressed as you turn the product on.
When the ‘Permanent Storage Init.’ Message appears on the display, release the button.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Need a way to make background sound continuous when combining clips?

I suspect the answer to this is that it can't be done in iMovie 8 and I need to use iMovie HD, but let me ask anyway. Perhaps one of you can tell me a clever way to do this.
I am creating a home movie of a wedding, in which there is background music on the soundtrack. When I go through the normal process of combining short clips, it sounds terrible, because the background music gets all hashed up into short pieces. What I'd like is to have the background music be continuous and just have the video jump around from clip to clip.
I'm guessing that I need to use some other software to pull the background music out as an mp3 file and then superimpose it just like I would any other music. Is that right? Can anyone suggest a method for extracting the soundtrack?
Thanks for any help.

The problem was that I didn't have the background music as a separate clip. However, I have downloaded MPEG Streamclip, and that seems to be a feature to allow you to pull out the sound from a video and make an mp3 file. So I plan to try that.

How to make a reset password function work in OIM?

There is a requirement for resetting password for users in OIM.
An OIM admin should be able to reset a password for a specific user, and the new password which should NOT be known by the admin will be sent to the user via email. And the user will be required to change his password when he logins with the new password.
I know there is a 'Change Password' button in User Detail page. But the problem is the admin has to type a password for the user, which means the new password is exposed. Ideally, the new password is generated by system. Has anyone had any experience in dealing with this kind of case? Thanks!

See if this can solve or answer your requirements.
When User's account is locked, It is assumed that he has forgotten his password.
Write a scheduled task which looks for all the locked users.
Generate temporary password for them.
Send that password in a mail to those users.
This may not be exactly how you want it to be. But this will require lesses efforts as compared to customizing "Change Password" button on admin console.
To make it the way you want, Following approach can be useful.
Admin console of OIM is made using struts framework. So If you know struts, Reading into struts-config.xml file will tell you the action class which is executed on click of "Change Password".
Modify that action class and make it the way you want that to be.
-Kiran Thakkar

Can`t make it start, continuously flashing led

Hi, I have a Power Mac g5 2.0ghz with 4 memory slots. Sudenly I can`t make it start. I get continuosly flashing led without hearing the start bep.
I try:
1) changing the ram
2) changing video card
3) reset PRAM
4) reset SMC
5) cleaning the Ram with rubber
6) using a hairdryer in the motherboard
7) disconnecting the CD Player and Hard Drive
Some times (1 in 20) I can get the machine to start, but when I turn it off it does the same and I get the flashing led.
Power light status
What it means
On and solid
Computer is on and running
2 flashes, pause
No memory (RAM) is installed
3 flashes, pause
Incompatible memory (RAM) is installed
4 flashes, pause
No good DIMM banks detected
5 or 6 flashes, pause
Contact Apple or an Apple Authorized Service Provider
I should contact a service?????
Thanks

I should contact a service?????
Hello, sadly Apple no longer works on G5s, nor has any parts, you might find an independant AASP that might in your area.
If you're sure the RAM is good, try the Hair Dryer trick...
http://discussions.apple.com/message.jspa?messageID=13240047#13240047
https://discussions.apple.com/message/15223603#15223603
https://discussions.apple.com/message/15499912#15499912
https://discussions.apple.com/message/15613068#15613068
https://discussions.apple.com/thread/3270112
https://discussions.apple.com/message/16053892#16053892
No power light at all...
https://discussions.apple.com/thread/3692775?tstart=0
It can show on any G5, and even many other computers & electronic devices of the period.
http://www.macintouch.com/reliability/pmg5.html
http://lowendmac.com/ppc/power-macintosh-g5.html
And see this last one in particular...
https://discussions.apple.com/message/16781690#16781690
Heat gun better...
https://discussions.apple.com/thread/3916312?tstart=0

Latest Leopard upgrade makes fan run continuously

After doing the latest Leopard upgrade, the fan on my G5 now runs continuously. It always would come on for a bit, then stop for a much longer period. Anyone know of a way to stop this, short of reinstalling the old original Leopard, and never again doing upgrades? Thanks for any help

Well, I do recall that activity monitor trick working well for fixing a laptop that ran all the time. It was looking for a printer that wasn't there. But the SMU trick is new for me. I didn't know the exact age, but pull the fan etc out and found the button. Actually the button said PMU (not SMU) reset, and I pressed it and restarted the computer. The fan was off for a while, but then it came back. I may try it again, since it seemed to have some effect.
Thanks for the suggestions
-wayne

Pange Extender Makes HH5 Reset Continuously

Similar Messages

Maybe you are looking for