Panic! My G5 just died (fuse went out at my office and now it wount start)
A fuse just went out in my office so all the power went out including the power to my G5!
Now when the power is back on the G5 refuses to start, when I push the on button I just here a clicking sound and then nothing and the light by the button goes on as long as i push the button.
Is my G5 toast or is there a fuse in the computer that has been blown?
Well - you could try a PMU/SMU reset. Can't remember if your G5 has a PMU button - but the process in detail and a few more suggestions here
http://discussions.apple.com/thread.jspa?messageID=3084827#3084827
Similar Messages
-
My iPad just died. The gear symbol came up and then the screen went blank (turned off). It was fully charged so that wan't the issue.
That is indicating that the device has gone into recovery mode. Press just the Power button until the red Power Off slider appears and slide to turn it off. Then power it back up to see if it has exited Recovery Mode. If it has, then you should be good to go.
If it has not, then the issue you had that caused the iPad to turn off was one that put your device into Recovery mode requiring that you go through the recovery process (i.e., the reset did not process since the issue required a recovery to resolve). Here is a link that explains what you need to do to get out of Recovery Mode in that case:
If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support
This article tell you how to restore your device using a backup:
Back up and restore your iPhone, iPad, or iPod touch using iCloud or iTunes - Apple Support
Post back with any questions!
Cheers,
GB -
my ipod touch died in the middle of a upgrade and now it wont come back on. When I charge it, it just goes to the apple but not the home screen. how do i fix it
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
MacBook died. Went to plug it up and power it back on, and it made an odd beeping sound. It failed to power up, and the light stays constant and doesn't blink. i unplugged it to wait for the light to turn off, which it did after a few minutes, but when I plug it back up to try again, the light comes on and stays on, but it won't power back up. I've also tried holding down the power button for up to 30 seconds and it doesn't do anything. Any tips or hopefully answers to this issue?
Hi. You might have a memory problem. With one or more of your ram being bad. If this is so you can try removing the ram one at a time and try to restart . You can also switch ram slots to make sure ifs not the ram slot. Before you do this try a pram reset. Command/Option/P/R holding down these keys while starting up for three chimes. Also a SMC reset.http://support.apple.com/en-us/HT201295 http://support.apple.com/en-us/HT202768
-
my iphone just went all hot turned off and now wont turn back on, any ideas??
Let it cool and then reset it... press the home and sleep buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.
-
Hi, I was working at home with my iPad, everything was going well. It went out battery and after this I am unable to connect to the wifi at home. Before getting out battery no problem, and now it sees the router signal but it is unable to connect to it.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
I just updated my iphone 4sto 6.0.1 and now my wifi is greyed out
I just updated my iphone 4sto 6.0.1 and now my wifi is greyed out
http://support.apple.com/kb/TS1559
-
I have just updated my software to 10.8.2 and now my sound doesn't work. Any suggestions?
I used disk permission repair to try to resolve this as well as a 'soft' restart. Still have a grayed-out mute checkbox in the sound section of system preferences.
-
I just upgraded to the new mobile me calendar and now all my calendar entries on iCal have been erased. As I type this the calendar entries are still on the mobile me and iphone calendars. How do I restore the calendar entries to iCal?
Please always post your System details when you have a query. The upgrade to the new MobileMe calendar produces different results, and different problems, with different versions of OSX.
Snow Leopard: during the upgrade process your iCal calendars should be moved to MobileMe (this can take some time and you have to wait for it to happen). Once done, your iCal reads the calendars from MobileMe so any changes made in either place will be visible immediately. If this has not happened then this Apple Tech Note provides instructions:
http://support.apple.com/kb/TS3397
Leopard: when the upgrade is completed iCal on Leopard will not be able to see the MobileMe calendars until an additional process is carried out, detailed in this Apple Tech Note:
http://support.apple.com/kb/HT4330
Tiger: iCal on Tiger cannot read the MobileMe calendars, period. The only workaround is to upgrade to Leopard, or Snow Leopard if possible (Intel Mac required). -
I just rented 2 movies on my Apple TV and now I am getting the message, "Your Apple TV is not authorized to play this content". Now I have 2 Apple TV's and they both are saying the same thing. Yes, I have done reset, restore, etc. but nothing! Frustrated & out $10.
Apple TV (3rd generation), OS X Mountain Lion (10.8.3), 2 Apple TV's (3rd Generation).Good call!! Thanks a million. Glad I asked & thanks for the quick response. I was getting frustrated. Thanks again!!!!!
-
I just rented 2 movies on my Apple TV and now I am getting the message, "Your Apple TV is not authorized to play this content". Now I have 2 Apple TV's and they both are saying the same thing. Yes, I have done reset, restore, etc. but nothing! Frustrated & out $10.
Good call!! Thanks a million. Glad I asked & thanks for the quick response. I was getting frustrated. Thanks again!!!!!
-
Hi, I've just downloaded the latest release 10.1.1 and now I do not see any more correctly my clips either in the canvas and in the timeline. Playing clips, they now appears with garbled images, completely unstables: I can not editing in these conditions!
Anyone can help me?
Thank you, ClaudioHi Russ, Thank you for your reply!
System Spec:
2x2.26 Ghz QUAD-CORE
12 GB RAM 1066 MHz DDR3
I've stored the library in HARD DISK which is installed inside my computer (1 TB capacity) and different from my hard disk in which I've installed all my applications (600 GB capacity).
I've installed FCP since 2001, bought FCP X in 2012: never had a problem. Yesterday I was editing my video of my last vacations (in California!) and I have updated FCP X, downloading FCP X 10.1.1: then the problem!
Strange is the fact that I've just tried to export a short project, I can see the final product quite well.
What is impossible is playing the clips within Final Cut: they are jumpimg, moving, presenting some frame in green or red ...
Everything all right in iMovie.
I've just checked the RAM: 9GB out of 12 GB is busy, could this be the problem?
Motion is very slow: for 20 sec of project, it takes minutes to play. And once again, if you finalize the projet and export it in Quicktime, you can see it correctly.
I do hope you may suggest something, I'm getting crazy!
Thank you in adavance
Claudio -
Question
I just updated to the latest version of Firefox and now I can no longer download facebook videos with realplayer as I formerly could. How can I downgrade to my previous version of Firefox?Many thanks b Noir
This is a copy of ONEof the keys in the registry I changed as told by Apple support today. I also have changed others as instructed by GEAR software support to manually delete GEAR drivers (that I had installed but couldn't delete some of the others they mentioned from Windows system 32. Then some bright spark at work told me I need the Gear drivers so I downloaded the software and installed again.
Sorry, just this minute went to insert image and it is giving me a message saying this sort of content is not allowed?.
The most recent key I altered is in: HKey _local _machine. System\class - 4D36E965-E325-11CEBFC1-08002BE10318. Upper Filter data: Upper filter NTIDrvr SiRem GEARAspiWDN.
The GEARsoftware info about manually deleting GEAR drive is from:
http://www.gearsoftware.com/wiki/index.php?title=DRIVERS:_Windows_-_Updating%2C_ removing%2C_64_bit_versions%2C_etc
I hope you can help -
I Just updated to the latest Apple TV software and now have no Movie trailers. Have they done away with Movie trailers?
Many thanks b Noir
This is a copy of ONEof the keys in the registry I changed as told by Apple support today. I also have changed others as instructed by GEAR software support to manually delete GEAR drivers (that I had installed but couldn't delete some of the others they mentioned from Windows system 32. Then some bright spark at work told me I need the Gear drivers so I downloaded the software and installed again.
Sorry, just this minute went to insert image and it is giving me a message saying this sort of content is not allowed?.
The most recent key I altered is in: HKey _local _machine. System\class - 4D36E965-E325-11CEBFC1-08002BE10318. Upper Filter data: Upper filter NTIDrvr SiRem GEARAspiWDN.
The GEARsoftware info about manually deleting GEAR drive is from:
http://www.gearsoftware.com/wiki/index.php?title=DRIVERS:_Windows_-_Updating%2C_ removing%2C_64_bit_versions%2C_etc
I hope you can help -
i went to update my iphone and now it says no sim grrrr and keeps telling me to connect to itunes which says no sim
Your iPhone is in recovery mode. Do the following to get it out of recovery mode.
Plug your iPhone into your computer with iTunes open make sure iTunes recognizes the iPhone in recovery mode.
Hold down the power button and the home button to do a hard reset and shut it off
Keep your finger on the Home button ONLY and unplug the iPhone from the cable
Release the Home button and allow the iPhone to power back on which may take a few minutes
The iPhone will return to its prior format
Hope that helps!
Maybe you are looking for
-
Idsm-2 problem: sensor upgrade from 4.1 to 5 or higher
Hi all, I have a problem with my IDSM-2 module. I'm trying to sensor upgrade from IDS to IPS software (from 4.1 version to 5.x or higher). If I do this from sensor under "admin user" and use major patch - IPS-K9-maj-5.0-1e-S149.rpm.pkg then I receive
-
WebApp not running of using DeployTool
When I deploy an EAR with a Web project from the Eclipse IDE, the deployment is going fine and the website is available immediately. But when I use the deployment tool - with a deploy-manager-config.xml - the website is NOT running after deployment..
-
Since I haven't received any answer to my topic and since there is at least another iDVD6 user having the same problem I am asking the question again. After I make a slide show DVD from pictures, burn it and put it away, if later on I try to open it
-
Can not download Itunes. error 7
Can not install Itunes. Error7 (windows error 5)
-
Cleaning up the Grid Control Repository Database
Our Grid Control Repository database has grown large over time and we need to free up some space. When we remove targets, is all the data related to the target cleaned out?