Panic when using USB 2 multi card reader

On 2 different intel iMacs, I've got the following error using a USB2 Multi Card Reader (Shows up as a Mass Storage Device under Sys Pref):
IOUSBMassStorageClass has corrupted the registry
Registry - am I running windoz or something??!?!?!
I've used this multi card reader on my G4 for a long time and never had any problems with it. On these 2 different intel iMac's it often stops importing my photos, and sometimes won't mount my memory stick cards. One one occasion I got the black/gray screen telling me to restart my computer, and that's when I got the message above. Yes, I've tried other memory cards, and a different USB cable... and at times I still loose communication with the card reader.
Any suggestions would be great.
Thanks!
24" iMac 2.16 GHz Intel Core 2 Duo at Home! Mac OS X (10.4.9) 17" iMac 1.83 GHz Intel Core 2 Duo at work!

Hi, is your card reader Mac Intel compatible? which manufacturer?
I would Repair Permissions then Turn Off. Disconnect everything except KB/M
restart - I would run OnyX..then Turn Off, connect all your usb & firewire - including card reader if mac compatible! Restart..L

Similar Messages

Kernel Panic when using USB Drive

This post originally started in the Time Machine topic but it now seems to be a basic issue with the USB i/f.
I am using a iMac IntelC2D to backup to a Seagate FreeAgent 750 USB drive. Everything has been working OK but just recently I have been suffering crashes every time Time Machine runs. I have reset PRAM but the problem persists. I have tested the backup volume on another machine running OS X 10.5.1 and it works OK. Testing with a different USB drive on the iMac causes the same problem. The hard drive itself is therefore OK. It seems to be a problem with the USB i/f on the iMac.
These are a couple of the crash reports which point to com.apple.driver.AppleIntelCPUPowerManagement
Is this a H/W problem? Suggestions are invited.
Wed Jan 9 15:59:00 2008
panic(cpu 1 caller 0x001A7BED): Kernel trap at 0x0000677c, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0xfa8d7de0, CR3: 0x010c9000, CR4: 0x00000660
EAX: 0xfa8d7de0, EBX: 0x00c1fb2c, ECX: 0x5ba860d7, EDX: 0x00000bde
CR2: 0xfa8d7de0, EBP: 0x348afd18, ESI: 0xfa8cbfdf, EDI: 0x00000000
EFL: 0x00010046, EIP: 0x0000677c, CS: 0x00000008, DS: 0x04260010
Error code: 0x00000002
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x348afb28 : 0x12b0e1 (0x455670 0x348afb5c 0x133238 0x0)
0x348afb78 : 0x1a7bed (0x45ea20 0x677c 0xe 0x45e1d4)
0x348afc58 : 0x19e517 (0x348afc70 0x0 0x348afd18 0x677c)
0x348afc68 : 0x677c (0xe 0x4260048 0x10 0x10)
0x348afd18 : 0xc0b770 (0xfaac4b9f 0xbde 0x0 0x0)
0x348afe38 : 0x1a8a6a (0xffffffff 0x7fffffff 0x348afec8 0x6)
0x348afe58 : 0x1a1a4e (0x0 0x40f34f0 0xfa8cb366 0xbde)
0x348afe88 : 0x135772 (0x2e85e4bc 0xfa8cb366 0xbde 0x2e85e4a8)
0x348afee8 : 0x135d3a (0x1 0x40f34f0 0x4022e3c 0x0)
0x348aff38 : 0x13685a (0x40f350c 0x0 0x0 0x5b8984)
0x348aff78 : 0x1368db (0x41bf70 0x417ab00 0x0 0x417ab00)
0x348aff98 : 0x41c02f (0x41bf70 0x417ab00 0xbfff7630 0x40f0000)
0x348affc8 : 0x19e2ec (0x417ab00 0x0 0x1a10b5 0x47a0d60)
Backtrace terminated-invalid frame pointer 0
Kernel loadable modules in backtrace (with dependencies):
com.apple.driver.AppleIntelCPUPowerManagement(9.25.0)@0xc08000->0xc1ffff
BSD process name corresponding to current thread: kernel_task
Mac OS version:
9B18
Kernel version:
Darwin Kernel Version 9.1.0: Wed Oct 31 17:46:22 PDT 2007; root:xnu-1228.0.2~1/RELEASE_I386
System model name: iMac7,1 (Mac-F42386C8)
Wed Jan 9 15:59:00 2008
panic(cpu 1 caller 0x001A7BED): Kernel trap at 0x0000677c, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0xfa8d7de0, CR3: 0x010c9000, CR4: 0x00000660
EAX: 0xfa8d7de0, EBX: 0x00c1fb2c, ECX: 0x5ba860d7, EDX: 0x00000bde
CR2: 0xfa8d7de0, EBP: 0x348afd18, ESI: 0xfa8cbfdf, EDI: 0x00000000
EFL: 0x00010046, EIP: 0x0000677c, CS: 0x00000008, DS: 0x04260010
Error code: 0x00000002
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x348afb28 : 0x12b0e1 (0x455670 0x348afb5c 0x133238 0x0)
0x348afb78 : 0x1a7bed (0x45ea20 0x677c 0xe 0x45e1d4)
0x348afc58 : 0x19e517 (0x348afc70 0x0 0x348afd18 0x677c)
0x348afc68 : 0x677c (0xe 0x4260048 0x10 0x10)
0x348afd18 : 0xc0b770 (0xfaac4b9f 0xbde 0x0 0x0)
0x348afe38 : 0x1a8a6a (0xffffffff 0x7fffffff 0x348afec8 0x6)
0x348afe58 : 0x1a1a4e (0x0 0x40f34f0 0xfa8cb366 0xbde)
0x348afe88 : 0x135772 (0x2e85e4bc 0xfa8cb366 0xbde 0x2e85e4a8)
0x348afee8 : 0x135d3a (0x1 0x40f34f0 0x4022e3c 0x0)
0x348aff38 : 0x13685a (0x40f350c 0x0 0x0 0x5b8984)
0x348aff78 : 0x1368db (0x41bf70 0x417ab00 0x0 0x417ab00)
0x348aff98 : 0x41c02f (0x41bf70 0x417ab00 0xbfff7630 0x40f0000)
0x348affc8 : 0x19e2ec (0x417ab00 0x0 0x1a10b5 0x47a0d60)
Backtrace terminated-invalid frame pointer 0
Kernel loadable modules in backtrace (with dependencies):
com.apple.driver.AppleIntelCPUPowerManagement(9.25.0)@0xc08000->0xc1ffff
BSD process name corresponding to current thread: kernel_task
Mac OS version:
9B18
Kernel version:
Darwin Kernel Version 9.1.0: Wed Oct 31 17:46:22 PDT 2007; root:xnu-1228.0.2~1/RELEASE_I386
System model name: iMac7,1 (Mac-F42386C8)
This is a repeatable problem on the iMac.

Just as final note on this topic. I discussed the problem with the local Apple Repair Centre who advised reinstalling 10.5.1, as suggested by baltwo, before bringing the machine in for repair. I did this and everything seemed OK. It has been running backups for 10 days now without a problem.

Kernel Panic when using Garageband with Blue Snowball USB mic

*HI ALL,*
*I purchased Mac Pro recently about 3 weeks ago. I am on the latest updates including the recent firmware update. However whenever I use garageband with external USB mic(Blue Snowball) my Kernel Panics and OS freezes and forces me to Power On again. It happened 20 times so far in few hours.*
*I opened garageband first time today after bought this external mic from apple store. I did not use garageband without this mic plugged into USB, I only used garageband with MIC plugged in and in couple of minutes to 5 minutes of using garageband the Kernel Panic occurs. Need your help please. Here is the message I get after login again which I reported consistently to Apple. Any immediate help is appreciated. I use iMove, iPhoto and other apps without any problem. Harddisk verification went o.k.*
Sun Apr 6 22:13:35 2008
panic(cpu 7 caller 0x001A8C8A): Kernel trap at 0x004209d5, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0x0000000c, CR3: 0x013fe000, CR4: 0x00000660
EAX: 0x00000000, EBX: 0x0ea7c3c0, ECX: 0x1059f4f0, EDX: 0x85ccfb8c
CR2: 0x0000000c, EBP: 0x85ccfb08, ESI: 0x0ea7c3c8, EDI: 0x0ea7c3d0
EFL: 0x00010202, EIP: 0x004209d5, CS: 0x00000008, DS: 0x11ac0010
Error code: 0x00000002
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x85ccf8f8 : 0x12b0f7 (0x4581f4 0x85ccf92c 0x133230 0x0)
0x85ccf948 : 0x1a8c8a (0x461720 0x4209d5 0xe 0x460ed0)
0x85ccfa28 : 0x19ece5 (0x85ccfa40 0x4256f6 0x85ccfb08 0x4209d5)
0x85ccfa38 : 0x4209d5 (0xe 0x85cc0048 0x10 0xe920010)
0x85ccfb08 : 0x42028d (0xea7c3c0 0x85ccfb8c 0x0 0x0)
0x85ccfb58 : 0x420c0e (0xea8b700 0x420978 0x85ccfb8c 0x0)
0x85ccfba8 : 0x6055d9 (0xea7c3c0 0x0 0x85ccfc08 0x615b08)
0x85ccfc08 : 0x609a11 (0xe92a000 0xeed0240 0xf56bff 0x0)
0x85ccfc68 : 0x86334bde (0x13c56800 0xeed0240 0xf56bff 0x0)
0x85ccfcd8 : 0x86334ddd (0xfbe4400 0x2 0x1 0x14)
0x85ccfcf8 : 0x86335056 (0xfbe4400 0x14 0xf7f4a80 0x7c79d6)
0x85ccfd38 : 0x86335156 (0xfbe4400 0x54 0x0 0xf7f4a80)
0x85ccfd88 : 0x9f2e64 (0xfbe4400 0x8634d000 0x862c1010 0x110a)
0x85ccfdf8 : 0x9eec9f (0xfd03600 0x10506588 0x110a 0x3ea740)
0x85ccfe68 : 0x9ee169 (0x13d7d000 0x110a 0x13c4c940 0x13dbab7c)
0x85ccfea8 : 0x43c47e (0x13d7d000 0x110a 0x55f 0x1)
Backtrace continues...
Kernel loadable modules in backtrace (with dependencies):
com.apple.driver.AppleUSBAudio(2.5.4b4)@0x86326000->0x8634cfff
dependency: com.apple.iokit.IOAudioFamily(1.6.4b7)@0x9e4000
dependency: com.apple.iokit.IOUSBFamily(3.0.8)@0x5ff000
com.apple.iokit.IOAudioFamily(1.6.4b7)@0x9e4000->0x9fafff
dependency: com.apple.kext.OSvKernDSPLib(1.1)@0x9e1000
com.apple.iokit.IOUSBFamily(3.0.8)@0x5ff000->0x626fff
BSD process name corresponding to current thread: GarageBand
Mac OS version:
9C7010
Kernel version:
Darwin Kernel Version 9.2.2: Tue Mar 4 21:17:34 PST 2008; root:xnu-1228.4.31~1/RELEASE_I386
System model name: MacPro3,1 (Mac-F42C88C8)

I've been getting a number of kernel panics when using USB Mics with Skype, though I have not experienced any crashes when using Garageband.
The crash report cited the AppleUSBAudio driver as the culprit. Here's the set up:
MacBookPro Core2 2.66 15"
Mac OS X 10.5.2
Blue Snowflake USB Mic, Blue Snowball USB Mic
Skype (latest rev - 2.7.0.257)
AppleUSBAudio.kext version 2.5.6b3
Seems to be a lot of crashiness with USB Audio in 10.5.2 - let's hope we see a patch soon

Anyone using USB to PCMCIA card for Internet ?

Anyone using USB to PCMCIA card reader to access internet ?
http://www.synchrotech.com/products/card-rw_13.html
I read that the above card support Verizon's wireless broadband card and wondering if anyone is using this.
Thanks!

I purchased this same card and discovered that it is not compatible with Mac. The manufacturer agreed to return my purchase price.

Been trying to use an external memory card reader with my macbook air- connecting via usb port, air does not recognize device nor the microSD card from my gopro - help

Been trying to use an external memory card reader with my macbook air… connecting via usb port, air does not recognize device nor the microSD card from my gopro … help

Some external ones do not work with the Mac's although most do. There are some driver compadibility issues with Mavericks, so I would wait for an update.

USB Hub / External Card Reader recommendations?

Afternoon,
I have recently purchased a late 2012 27" iMac and would like to add some peripherals.
I am looking for a USB 3.0 hub and a multi card reader.
I have seen lots of posts about USB hubs (the joys of a google search) that either arent recognised as 3.0 or are on American sites. (Am based in the UK).
I know there is a card reader on the back of the iMac, but only for SD and I would prefer to not have to keep turning the monitor round to reach it. (I still have xD cards that I use).
Without being too picky, I dont want 'ugly' units. Dont want to make a beautiful machine look ugly when surrounded by lots of horrible looking external add-ons.
Does anyone have any recomendations of hubs / readers, or even ones to steer clear of?
Thanks very much.
Karen

Thanks for trying but ...
No, I can't see the drive when booted up with Cmd R.
I don't have a USB hub to test on.
I'm just tried resetting the PRAM as you suggested.
No change.
Any other ideas gratefully accepted, otherwise, I can book into the genius bar thingy - no idea if that will be of use. I work in IT so I'm fairly handy though there are many mac specific commands & tricks I'm not aware of.

Memory Card "Stuck" in A720 multi-card reader

This is an embarrassing situation. Really appreciate if someone can give me some idea.
I just got the A720 for a few days. I used SD cards fine with A720's multi-card reader, but last night when I (gently as with the SD cards) slotted in a regular Sony memory stick in it (6-in-1, accepting MS/ MS Pro), the whole stick moved beyond the opening and well into the slot. The A720 could detect the card and I immediately copied all the file into the HD and ejected it on Windows.
Now the memory stick remains in(side) the card reader slot, and I dare not touch it further lest it goes further inside. Is this a design flaw? I was appalled and am frustrated by how this could have happened -- I actually used my little finger to slot the card in!. I bought the A720 mainly for photo post-processing.
Any idea I can get the stick out (and even better slot it in without the same happening again)? Thank you.

Hi
Welcome To Lenovo Community
There are various reason for a memory card to get stuck inside the card reader
Most common is the direction in which the card is inserted, size of the card also matters or any obstacle which is their inside the card reader.
Push a little harder on the card and it might pop out. The spring mechanism on the inside is designed to release once it is pushed past a certain point.
If this doesn't work, you need to force it out using a flat tool. To do so Turn off your system , Press the Power Button for 15 seconds to drain out the remaining charge
Now use a needle nose pliers, areal long thin one. And gently pull the memory card out.
You can also try using a paper clip apply glue on the edge. Very tiny amount that won't drip push clip in and touch the back of the card. Wait until it is hard in about 15 secs and pull the card out.
if this does not work contact Local Lenovo service center , we need to open the card reader to remove the memory card
Hope This Helps
Cheers!!!
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with Kudos!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

R3000 multi card reader problem

I have a problem with the sd card reader on here that it wants to format the sd card when inserted, I searched the forum for others that were having the problem, and found that I possibly need the sp29788 updated driver for it, so I downloaded it to the laptop, but am still getting the same thing. The card that I am trying to read is a 2gb that I can read with usb multi card reader, but not the one in the laptop. The driver for the multi card reader shows a 8/8/2003 date on it, the driver on the hp website sp29788 shows a 2005 date. When I installed the updated driver for it, the date on the driver still shows as 2003. What next?

Hi lincon50
I understand the memory card isn't being recognized since the wireless setup and the apple update.
Please take a look at the post from pcwizard and give it a try.
http://h30434.www3.hp.com/t5/Other-Printing-Questions/transferring-photos-from-memory-card-to-comput...
Here is a url for memory card troubleshooting.
I would test the memory card in another device.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c00059994#N824
If you need more assistance just let me know.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Booting from USB Flash Memory Card Reader on RS480M2-IL (Test Results)

I just completed testing my USB Flash Memory Card Reader (see profile) as a boot device and wanted to provide feedback to the Forum.
A UBS Flash card will show-up on the Advanced Bios Features menu, Hard Disk Boot Priority list, when a Flash card is physically present in a card slot. It showed as "USB-HDD0 : AFT PRO -8MX CF 0" with a 256MB Compact Flash (CF) card for my test. Using the enter key on the Hard Disk Boot Priority list allows for ordering priority, which was necessary to place the CF Drive before my real Hard Drive for the card to boot. When the card is removed, it drops from the list.
I initialized my CF card as a DOS system disk using HP's USB Disk Storage Format Tool v2.0.6 for the test.
Since it is recognized as a Hard Drive, it boots as the C: drive, not A/B Floppy alternative.
I also ran a quick test to see if XP Pro Setup would see the drive. It does show as my D: drive partitioned FAT. Too small (256MB) obviously for XP Pro install, but it does present opportunity for larger size flash modules. My Flash Reader actually has 4 different disk functions/slot groups, so XP Setup acknowledge the presents of those empty three slot groups as "Unknown Disk" on the drive list.
I hope the information is useful for anyone planning a build or looking for alternative boot methodolgy with the board.
This board just gets better and better.
Danno

So with a nice size flash memory u could start your box with a key drive and lock up your computer when you leave it unattended.

SanDisk USB 3.0 Card Reader does not work with OSX Mavericks.

Since updating to OSX Mavericks (10.9) My USB 3.0 SanDisk "ImageMate All-in-One" Card Reader has begun to fail.
It all seems to work proper at first. The memory card shows up in finder and I'm able to browse the files. But when I try to transfer any files it un-mounts from finder and only transfers the first file.
This does not happen under previous OSX versions. I have tried on other computers since, so the card reader is fine.
My USB 2.0 card reader saved my life this time. It works totally fine.
Is this a known problem? Are you guys working on it?

Solved in this post here:
https://discussions.apple.com/message/24016337#24016337

How can I prevent iPhoto from auto-launching when I plug in a card reader?

When I plug in a card reader, iPhoto assumes that it is being summoned and auto-magically launches itself. I don't want this to happen. I don't want iPhoto to ever launch without my permission, which I might grant once a year or so. Yet, every day I have to cope with it launching multiple times as I attempt to transfer photos to my hard drive. It is a minor annoyance, true, but it is an annoyance.
My question, then, is how can I make iPhoto stop doing this? I've searched its settings high-and-low, but to no avail. I've searched the System Preferences high-and-low, but to no avail. There must be something I'm missing.
Help me, Apple Forums, you're my only hope!
any Macintosh Mac OS X (10.4.2)

Hi John,
the next info is on using Image Capture to download the images. In the preferences though, you can choose to have nothing open when the camera is connected.
Using Image Capture to download images and video clips:
Open up Image Capture which is found in the Applications folder.
When it is opened, go to Image Capture/Preferences
Under the General button choose
Camera: When a camera is connected, open Image Capture.
The next time you connect your camera Image Capture will open.
In the window that opens you will see an Options button. Click on that button to set your options.
To find out more about Image Capture (it can do a lot more) Click on Help in the menu bar when Image Capture is open.
iPhoto: How to Change the "Open Automatically" Preference
If you find you can't change any of Image Captures preferences or can't access any drop down menus or they are greyed out, check to make sure Image Capture is loose in the Applications folder and not within a sub folder.
Lori

Hp officejet pro 8600 multi-card reader problem

Have officejet 8600 printer/fax with multi-card reader. All worked fine when wired to Apple computer before. Went wireless last week...set up router etc. All worked fine till I tried to load an sd camera card in the printer like i had done many times before. Doesn't recognize the multi-drive...all lights start to flash..tells me i need to turn printer off/on to continue....NEVER does recognize the card reader!...
I remember there was an update from Apple that had to do with printer drivers on Oct.15th....could that be the problem or do I need to set something else because of the wireless setup?
The printer works fine otherwise....it does recognize the wireless connection for straight printing. I haven't tried the fax part yet.

Hi lincon50
I understand the memory card isn't being recognized since the wireless setup and the apple update.
Please take a look at the post from pcwizard and give it a try.
http://h30434.www3.hp.com/t5/Other-Printing-Questions/transferring-photos-from-memory-card-to-comput...
Here is a url for memory card troubleshooting.
I would test the memory card in another device.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c00059994#N824
If you need more assistance just let me know.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Search for a driver: Ricoh Multi Card Reader for Windows 8 - for my T61 (6463) -

Hi!
I`m searching for a Windows 8-Driver for my T61 (6463).
I have a Ricoh Multi Card Reader inside and I can`t find a driver for this one.
Can anybody help me?
Thank you,
Heiko
Solved!
Go to Solution.

Hello,
Try downloading the following driver:
Name: Ricoh Multi Card Reader Driver for Windows Vista, XP
Version: 3.54.02
Date: 06 Mar 2008
URL: http://support.lenovo.com/en_US/detail.page?LegacyDocID=migr-68053
The drivers will extract to a directory named "C:\DRIVERS\WIN\4IN1\", if I recall correctly. Once extracted, run Device Manager (filename: DEVMGMT.MSC), go to the entry where the unrecognized card reader is located, and perform an update, using the "Have Disk" option and pointing it to the directory in which the drivers were extracted.
I do not recall if a reboot is required, but in any case I would recommend doing one, at which point you should then be able to see the card reader from Windows 8.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

How can we interface external usb camera or usb device(storage, card reader) to Ipad 2.What all things are need(any development Kit apart from IOS sdk)

Hi,
Before going any further in my research, I want to know the views and opinions about the intent of my work I am about to start.
AIM : I am trying to interface an external uvc camera with the ipad 2 and iphone .Just like in android there is a node(in unix and linux everythign is a file)which gets created in the /dev/ directory which can be accesses by the application using the native interfaces (JNI) and finally via the android code.I am trying to develop the similair application for the ipad 2 and iphone.
Can some one plz point out :
(1) How I can interface external hardware like ( external uvc camera) or any other USB device(a card reader, a storage device, a barometer etc)
(2) I have googled about Apple's Authentication chip which can be used to interface the external h/w.Can some one point out how useful it is.Is this related to that somehow.
(3)What are the things similair to JNI, node, /dev/ in the IOS for Ipad 2 and Iphone.
I will be highly obliged ,if some one could provide me the top pointers on it.
Thanks and Rgds,
MangoApple

1.) See
External Accessory Programming Topics
Connecting to an Accessory
Monitoring Accessory-Related Events
2.) See the MFi Program

Does Mackie Control work with Final Cut 7 when using USB MIDI?

I have a Mackie Control Universal Pro connected via USB to my mac and it works GREAT with Logic and all the complimentary Logic Studio software.
The problem I am having is, when I try to use it with Final Cut, it wont work at all. I have read the post concerning this that was answered by Andy Mees but, I dont use a true MIDI connection, only USB.
Any thoughts?

Does Mackie Control work with Final Cut 7 when using USB MIDI?
No one will know until FCP 7 is released.
-DH

Panic when using USB 2 multi card reader

Similar Messages

Maybe you are looking for