PAP2T Dialout disconnects after 15 seconds. Dialin Fine...???

I have the PAP2t, I am using Gizmo5 service.
I can get calls dialed in no problem.
Dialing out, I get a problem - all calls are disconnected after 15 seconds - always the same!. I have tried a ton of different settings and resetting to defaults, upgrading firmware... Any ideas?
Solved!
Go to Solution.

Thanks, but I just got it fixed. Was a problem with my (dare I say?) Netgear router - WRV2000. All the netgear's router latest firmware (from a year or more) all are incompatible. Had to downgrade firmware to something that worked 1.1.3.9
Now works like a charm...

Similar Messages

Skype account keeps disconnecting after 30 seconds

hi guys,
its driving me nuts. my skype account keeps disconnecting after 30 seconds and i haven't even done anything. it does it on windows, and on my iphone too.
what's going on? is this a problem with skype? i've seen similar posts. and i'm using skype 6.20

That generally means there is an issue with your Microsoft account. You may have to verify some settings in your account to make sure a configuration isn't causing it. The only solution I'm aware of is temporarily unlinking your account. I do not know if reconnecting it will resolve the issue right away.
https://support.skype.com/en/faq/FA12211/

Blank login screen on the iPad keeps popping up and wifi disconnecting after 20 seconds

hi, we have an ipad running IOS 5 that keeps having a blank login screen on the iPad keeps popping up and wifi disconnecting after 20 seconds.
I am yet to find out why this is, any clues? (note that both apple.com and facebook are blocked at the router, but nothing else)...

actually we cannot due to policy reasons... it appears through testing that the iPad is phoning home and sending private data to Apple regardless, it is also odd they placed these PRIVACY settings in About hidden away so that no-one knows they are there.
From the iPad homescreen, tap on Settings > General > About
Tap on "Diagnostics & Usage" > select "Don't Send"
So... anyone else know why if we block Apple, the iPad disconnects from the internet via Wifi?

[SOLVED]Kindle 5 disconnects after few seconds (USB)

Hi,
I have problem with my Kindle e-book reader. It worked fine last week, but now it keep disconnecting from laptop.
When I plug it in (using USB 2.0), it is recognized, according to lsusb, but after few seconds it "disappears" from list.
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 004: ID 1949:0004 Lab126, Inc. Amazon Kindle 3/4
Bus 001 Device 003: ID 2232:1018
and dmesg shows this:
[ 44.233222] usb 1-1.2: new high-speed USB device number 5 using ehci-pci
[ 44.338977] scsi7 : usb-storage 1-1.2:1.0
[ 45.341509] scsi 7:0:0:0: Direct-Access Kindle Internal Storage 0100 PQ: 0 ANSI: 2
[ 45.347348] sd 7:0:0:0: [sdb] 2846720 512-byte logical blocks: (1.45 GB/1.35 GiB)
[ 45.453629] sd 7:0:0:0: [sdb] Write Protect is off
[ 45.453643] sd 7:0:0:0: [sdb] Mode Sense: 0f 00 00 00
[ 45.563370] sd 7:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 45.784393] sdb: sdb1
[ 46.013362] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 46.954279] usb 1-1.2: USB disconnect, device number 5
[ 46.955449] sd 7:0:0:0: [sdb] Synchronizing SCSI cache
[ 46.955581] sd 7:0:0:0: [sdb]
[ 46.955591] Result: hostbyte=0x01 driverbyte=0x00
For powersaving I use tlp and I have this device blacklisted, so it shouldn't be the cause. And the autosuspend for USB is set to 2000s. I tried to google but nothing helps.
Thanks
Edit: It was because of two bad cables, the third one works. Sorry
Last edited by Kotrfa (2013-05-16 20:33:41)

First, connect it to another computer and try a differnet video connection. THis will tell you if the computer is doing something to contribute to teh problem...a.k.a. sending a sleep signal. If it still does not work and exhibits the same behaviour, then I am inclined to think that the backdisplay charging system (the inverter board) is not working correctly... that is, a capacitor(s) has failed.
... an HP employee expressing his own opinion.
Please post rather than send me a Message. It's good for the community and I might not be able to get back quickly. - Thank you.

SPA942 disconnects after 30 seconds.

My voip ph keeps hanging up after 30 seconds. I used to have a linksys wag200g and my voip worked fine but as soon as I changed my modem to a speedstream 6520 my voip ph keeps hanging up. I've been told I need to do port forwarding but the portforward.com website is a little vague for me. Pls help!!

Usually the ports that the SPA-942 uses are 5060-6061. Try to also set NAT Mapping Enable and NAT Keep Alive Enable to “Yes”. Go also to the Provisioning Tab and set Provision Enable to “No”.

Users join lync meeting and get disconnected after 1 second

I have an issues where some users join a Lync meeting but kicked off after a second or less. I see this error in the traces.
I have no idea what is causing this to happen.
response
xmlns="urn:ietf:params:xml:ns:cccp"
mscp="http://schemas.microsoft.com/rtc/2005/08/cccpextensions"
ci="urn:ietf:params:xml:ns:conference-info"
requestId="437979296"
C3PVersion="1"
from="sip:[email protected];gruu;opaque=app:conf:focus:id:Q3M30T0G"
to="sip:[email protected]"
code="failure"
reason="otherFailure">
+
<addUser
reason="otherFailure">
</response>

Hi,
Did the issue both happen internal and external the domain?
Please check if there is any error message on FE Server.
As the issue only happen for several users, please double check if there is any client/conference policy to deny these Lync users to join the Lync Meeting.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

Vod stream disconnects after 100 seconds of pause

I'm using fms 4.5 vod application to play rtmp stream in flex Video Display client.When the video is paused for 100 seconds the stream gets disconnected from server.its not resuming when the play method is invoked.The player's state is changing to 'playing' but the video is not playing. I tried the same client with fms 4.0 and it starts playing when the play method is invoked after disconnection.Can any one help to resume the video with fms 4.5?

You must have failed to accept the request for your microphone. You see "Error" when the function that asks for microphone fails.
It however doesn't mean your browser doesn't support it. In that case nothing would happen (unless you'd look into browser console).

SPA112 - my outgoing calls are disconnected after 30 seconds?

I have a SPA112 2 port phone adapter connected to a TP-LINK TL-WR841N. I can receive calls without problems. I can dial out, yet after 30-40 seconds into the call, I am disconnected. Can someone please help me resolve this issue. Thank you. Mike

Hard to help without informations. Please catch full syslog&debug messages
Debug and syslog Messages from SPA1x2 and SPA232D ATA (Analog Telephone Adapters)
and catch SIP messages
Installing and Using Wireshark for Capturing Network Traffic

Nokia CK20W Disconnects after 3 seconds

Hi All.
I have a Nokia Ck20W fitted in my car which has worked well for two years. When I had a problem with my Nokia phone, I used an HP Ipaq as a back-up.
When I tried to connect the Ipaq it showed that the connection had been made, but the disconnected almost imediately.
I have just upgraded to an HTC Desire but the same thing happens. I do not even get the opportunity to enter the pass code before it disconnects.
My wife's phone (and all my previous phones) works fine on the CK20w and the HTC Desire connects every time to the Nokia CK7w which is fitted in my wife's car.
Has anyone had a similar problem?
Thank you in advance.

Can't offer any help for you unfortunately but was wondering if you managed to get your HTC Desire to connect to the CK20W in the end. Was thinking of buying a CK20W kit of ebay for myself and was also looking at upgrading to the Desire in the near future but if you didn't get the two devices to connect I'll get the CK300 kit instead.

PPPoE stays connected forever despite "Disconnect after 30 seconds"

This is costing me a fortune. I have a PPPoE connection that charges me by the number of seconds I'm connected. Normally the Airport Extreme is great...it connects only when somebody's using it and disconnects when it's done.
About once a week, it just gets "stuck" and never disconnects. It doesn't tell me it's stuck (it's in the attic next to where the connection comes into the house). I just find out by checking my ISP and finding out that I've just been charged $50 for a full day of continuous connection.
Is there a way to automatically reboot it periodically (twice a day?). Or is there a way to fix this problem where it gets "stuck" and just keeps the PPPoE connection open?

Welcome to the discussions!
You might want to look a simple electronic timer that plugs directly into an AC socket so you could set the device to power on and power off daily at specified times.

New MacBook Pro Disconnects from OS X Server VPN after 60 seconds

My Old G4 Laptop and my Dual G5 Tower both connect to my office via L2TP VPN without an issue. with the exact same settings exported over to my mac book pro, the connection drops after exactly 60 seconds. I've tried both wireless and wired connections, and in either case, the VPN drops after 60 seconds of connect time.

I have exactly the same problem with a new iMac Duo Core 20". It disconnects after 60 seconds no matter what I try. With other Macs (non of which are Intel) I have no problems what so ever.

CME Jabber on iPhone disconnects after 10 Secs

Hi all, have a problem on my jabber clients that they disconnect after 10 seconds when making outbound calls. Router 2921 - c2900-universalk9-mz.SPA.151-4.M4.bin runing CME 8.6. iPhones running Jabber 8.6.5.18781. All other devices (CIPC, 7945's etc. (SCCP)) are working fine and are able to make outgoing and incoming calls.
please assist.
this is what I get from the CME
un 8 15:10:43.459: //-1/xxxxxxxxxxxx/SIP/Event/sipSPIEventInfo: Queued event from SIP SPI : SIPSPI_EV_CC_CALL_DISCONNECT
Jun 8 15:10:43.459: //-1/xxxxxxxxxxxx/SIP/Event/sipSPIEventInfo: Queued event from SIP SPI : SIPSPI_EV_CC_CALL_DISCONNECT
Jun 8 15:10:43.459: //1158/E2B9A9F18216/SIP/Event/Session-Timer/sipSTSLMain: Event: E_STSL_SPI_EVENT
Jun 8 15:10:43.459: //1159/E2B9A9F18216/SIP/Msg/ccsipDisplayMsg:
Sent:
BYE sip:[email protected]:5060;user=phone;transport=udp SIP/2.0
Via: SIP/2.0/UDP 192.168.244.250:5060;branch=z9hG4bK4291EAA
From: "Dave-iPhone" <sip:[email protected]>;tag=BDEC6C-1325
To: <sip:[email protected]>;tag=gf97ll6v-CC-24
Date: Fri, 08 Jun 2012 15:10:25 GMT
Call-ID: [email protected]
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1339168243
CSeq: 103 BYE
Reason: Q.850;cause=102
P-RTP-Stat: PS=539,OS=16170,PR=894,OR=17880,PL=0,JI=0,LA=0,DU=10
Content-Length: 0
Jun 8 15:10:43.495: //1159/E2B9A9F18216/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 200 OK
Via: SIP/2.0/UDP 192.168.244.250:5060;branch=z9hG4bK4291EAA
From: "Dave-iPhone" <sip:[email protected]>;tag=BDEC6C-1325
To: <sip:[email protected]>;tag=gf97ll6v-CC-24
Call-ID: [email protected]
Timestamp: 1339168243
CSeq: 103 BYE
Content-Length: 0
Jun 8 15:10:43.495: //1159/E2B9A9F18216/SIP/Call/sipSPICallInfo:
The Call Setup Information is:
Call Control Block (CCB) : 0x313A9000
State of The Call        : STATE_DEAD
TCP Sockets Used         : NO
Calling Number           : 7477
Called Number            : 0114674466
Source IP Address (Sig ): 192.168.244.250
Destn SIP Req Addr:Port : 192.168.244.10:5060
Destn SIP Resp Addr:Port : 192.168.244.10:5060
Destination Name         : 192.168.244.10
Jun 8 15:10:43.495: //1159/E2B9A9F18216/SIP/Call/sipSPIMediaCallInfo:
Number of Media Streams: 1
Media Stream             : 1
Negotiated Codec         : g729r8
Negotiated Codec Bytes   : 20
Nego. Codec payload      : 18 (tx), 18 (rx)
Negotiated Dtmf-relay    : 6
Dtmf-relay Payload       : 101 (tx), 101 (rx)
Source IP Address (Media): 192.168.244.250
Source IP Port    (Media): 17620
Destn IP Address (Media): 192.168.244.10
Destn IP Port    (Media): 20040
Orig Destn IP Address:Port (Media): [ - ]:0
Jun 8 15:10:43.495: //1159/E2B9A9F18216/SIP/Call/sipSPICallInfo:
Disconnect Cause (CC)    : 102
Disconnect Cause (SIP)   : 200
Jun 8 15:10:43.587: //1158/E2B9A9F18216/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 200 OK
Via: SIP/2.0/TCP 192.168.1.1:5060;branch=z9hG4bK428F1C;received=192.168.10.1
From: <sip:[email protected]>;tag=BDF344-F6
To: "Dave-iPhone" <sip:[email protected]>;tag=000000000000007f731c4248-4443c002
Call-ID: [email protected]
Date: Fri, 08 Jun 2012 15:18:20 GMT
CSeq: 101 BYE
Server: Cisco-SIPIPCommunicator/9.2.1
Content-Length: 0
Jun 8 15:11:01.471: //-1/xxxxxxxxxxxx/SIP/Event/sipSPIEventInfo: Queued event from SIP SPI : SIPSPI_EV_OUTBOUND_REGISTER
Jun 8 15:11:01.471: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
Sent:
REGISTER sip:192.168.244.10:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.244.250:5060;branch=z9hG4bK42A3FA
From: <sip:[email protected]>;tag=BE7960-2177
To: <sip:[email protected]>
Date: Fri, 08 Jun 2012 15:11:01 GMT
Call-ID: 38930D6E-B0AF11E1-81BCB8F2-331935B0
User-Agent: Cisco-SIPGateway/IOS-12.x
Max-Forwards: 70
Timestamp: 1339168261
CSeq: 11 REGISTER
Contact: <sip:[email protected]:5060>
Expires: 3600
Supported: path
Content-Length: 0
Jun 8 15:11:01.487: //1160/000000000000/SIP/Msg/ccsipDisplayMsg:
Received:
SIP/2.0 400 Bad Request
Via: SIP/2.0/UDP 192.168.244.250:5060;branch=z9hG4bK42A3FA
From: <sip:[email protected]>;tag=BE7960-2177
To: <sip:[email protected]>;tag=v7vgdted
Call-ID: 38930D6E-B0AF11E1-81BCB8F2-331935B0
Timestamp: 1339168261
CSeq: 11 REGISTER
Warning: 399 - "SoftX3000 R601-MSG Error ID:[259] LiteFME Tg register ,get Wll param error "
Content-Length: 0
Thanks
David

Just in case you haven't solved this yet, the issue is detailed below.
Workaround
Bind all SIP traffic to a single interface, ideally the voice vlan interface.
   voice service voip
       sip
         bind all source-interface gigabitEthernet 0/0
Cisco Mobile 8.1 integrated w/CME 8.6. On outgoing calls from Cisco mobile the call will connect, get 2 way audio and then disconnect after
15-20 seconds.
The problem is that when the call connects the CME sends a 200 OK to the Cisco Mobile app. The Cisco Mobile app fails to send an ACK to CME, so CME keeps sending 200 OK messages until it times out and ends the call.
The problem is related to CME using a different source IP address for SIP traffic than what was used for the endpoint to register. The IP used as the source address under Voice Register Global is what the TCP connection is set up to for an outgoing call. However the CME uses the best address to source traffic from when it is not bound. As these devices are on the WiFi network (not the wired voice network), the CME uses a different address to source the SIP traffic for these calls than what is defined under the voice register pool. This causes an error in the Cisco Mobile App, which is why it fails to return the ACK.
We bound SIP traffic globally under Voice Service Voip to the same IP that was defined under the voice register global. After this the calls worked fine.
Reference this Junked bug as well:
CSCtu05278   CME Call from Cisco Mobile to IP phone disconnects after
20 seconds

HT1595 I have hooked up a second apple TV in another room and neither can see my computer when both connected. When i disconnect 1 box it works fine?

I have hooked up a second apple TV in another room and neither can see my computer when both connected. When i disconnect 1 box it works fine?

Do a clean (re)install and delete the Firefox program folder (C:\Program Files\Mozilla Firefox\).
Download a fresh Firefox copy and save the file to the desktop.
*Firefox 10.0.x: http://www.mozilla.org/en-US/firefox/all.html
Uninstall your current Firefox version, if possible.
*Do NOT remove personal data when you uninstall the current version or you lose your bookmarks and other data because all profile folders will be removed.
Remove the Firefox program folder before installing that newly downloaded copy of the Firefox installer.
*It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
*http://kb.mozillazine.org/Uninstalling_Firefox
Your bookmarks and other profile data are stored elsewhere in the Firefox Profile Folder and won't be affected by a reinstall, but make sure that you do not select to remove personal data if you uninstall Firefox.
*http://kb.mozillazine.org/Profile_folder_-_Firefox
*http://kb.mozillazine.org/Profile_backup
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

Error -63043: FPGA disconnects after running for a few seconds

Hello,
I face the following problem whenever I try to run a FPGA VI directly from my host PC onto my PXI 7831R through the ethernet.
Initially, MAX shows my remote PXI system as 'Connected', and the FPGA VI compiles fine.
But when I hit the 'Run' button, the VI seems to run fine for 3-4 seconds, after which it hangs (screenshot attached). A couple of seconds later, it returns the following message :-
" LabVIEW FPGA called another software component and that component returned the following error
Error code: -63043
NI-RIO FPGA Communications framework: The session is invalid. The target may have reset or been rebooted. Check the network connection and retry the operation. "
The VI continues to run on the FPGA, but I can't control it anymore from my host-PC. Even MAX shows the remote system as disconnected, after this error occurs. All I am left to do is to reboot my host-PC as well as the remote PXI target; to reach the beginning of this problem.
I have checked the NI-RIO settings. Both my host-PC as well as remote PXI system have the same NI-RIO 3.0.0 version installed. I am running LabVIEW 8.6 .
Can anyone help ?
Attachments:
Error Screenshot.JPG ‏89 KB

Hi everyone, I have the same problem regarding the 63043 error code
I´ve simplified my FPGA vi up to a simple write and read program of a port, as shown in the attachment, but I still have the same error.
It´s interesting that the program runs, note in the jpg file that the while loop counter suddenly stops at Numeric=10, it means the program ran 10 iterations. Also the input port succesffully read the pin value, this meas that the program ran properly, but the SBRIO rebooted when Numeric was 10 and the target device disconnected from the project, i wonder why?
The target device is an sbRIO-9632 , serial number 01452AC3 with the following software installed:
NI-RIO 3.4.0 - January 2010
DataSocket for LabVIEW Real-Time 4.7.0
EPICS Server I/O Server 1.6.1
LabVIEW PID and Fuzzy Logic Toolkit 9.0.0
LabVIEW Real-Time 9.0.1
Language Support for Japanese 9.0.1
Language Support for LabVIEW RT 1.0.0.3
Modbus I/O Server 1.6.1
NI-RIO 3.4.0
NI-Serial RT 3.3.4
NI-VISA 4.6
NI-VISA Server 4.6
NI-Watchdog 4.0.1
Network Variable Engine 1.6.1
Run-Time Engine for Web Services 2.0.1
SSL Support for LabVIEW RT 2.0.1
System State Publisher 1.1.0
Variable Client Support for LabVIEW RT 1.6.1
Web Server for LabVIEW RT 2.0.0
Available add-ons:
LabVIEW Control Design and Simulation 9.0.1
However, if I run a program in the RT processor without referencing any vi on the FPGA it runs without problems, it´s only when a file is loaded into the FPGA that the system reboots and the error message appears.
Please help me
leito
Attachments:
error-63043.jpg ‏264 KB

Hello I have a problem with a Wifi Survey app, this app is from Access Agility, however this app was working fine, but without advise stop of working, I tried to open again, but app be close after few seconds.

Hello I have a problem with a Wifi Survey app, this app is from Access Agility, however this app was working fine, but without advise stop of working, I tried to open again, but app be close after few seconds. Every time that I tried to open it, in diagnostic and use create some files, in special one named LatestCrash-WifiSurvey.plist, this one generate an incident identifier E73B0164-CDFA-4E9E-839E-A0C021BD17A2, but this incident identifier change every time that I tried to open, the last incident identifier is: DE600EB3-AB57-4C33-8DE8-71F6788A7441.
After of it, I checked that the app had a new version available for downloading, I took a backup of my ipad and then upgrade this app, but is the same problem, all I want is to save the projects I had in this app, I´m afraid that if I delete this app and re-install it, probably I loss my projects.
Thanks for your help indicating how I can save my projects and see them for example in an iphone for assurance that data is not lost.
Something that called my attention is part of the log that shows a big CPU processing, but the strange thing is I killed all applications.
Incident Identifier: E73B0164-CDFA-4E9E-839E-A0C021BD17A2
CrashReporter Key:   ed0ca1405ce83d4f80cb3cce063d7248d7b76e91
Hardware Model:      iPad2,5
Process:         WifiSurvey [139]
Path:            /var/mobile/Applications/1BEEE35A-85FC-4BE4-B62A-39A930CB3CE2/WifiSurvey.app/Wi fiSurvey
Identifier:      WifiSurvey
Version:         ??? (???)
Code Type:       ARM (Native)
Parent Process: launchd [1]
Date/Time:       2013-08-08 19:01:13.476 -0500
OS Version:      iOS 6.1.3 (10B329)
Report Version: 104
Exception Type: 00000020
Exception Codes: 0x000000008badf00d
Highlighted Thread: 0
Application Specific Information:
com.accessagility.wifisurvey failed to launch in time
Elapsed total CPU time (seconds): 20.990 (user 20.990, system 0.000), 52% CPU
Elapsed application CPU time (seconds): 19.954, 50% CPU

See:
iOS: Troubleshooting applications purchased from the App Store
Contact the developer/go to their support site if only one app.
Restore from backup. See:
iOS: How to back up
Restore to factory settings/new iPod

PAP2T Dialout disconnects after 15 seconds. Dialin Fine...???

Similar Messages

Maybe you are looking for