PAP2T - Incoming Calls/Phone Compatibilty!

I have just bought my pap2t and having problems recieving incoming calls. My SIP account says that its registered and working on their end but when someone rings the number, it doesnt ring on my phone. Is there a specific type of phone that will work with the adaptor e.g. PBX, DECT phones? or could it be the settings?

eepro is referring to this web site which could be the answer.
Can you make outgoing calls?
On an incoming call is just the phone not ringing or can you pickup the phone and there is no connection (just receive dial tone)?

Similar Messages

PAP2T: Incoming calls being blocked by Router.

Hi,
I am trying to use an unlocked PAP2T Adapter with Telus home network in Canada and am not able to receive calls. I can make outgoing calls to any number in the world, but whenever I get a call back, the phone doesn't ring & later I find it in Firewall log as being blocked under "Low Risk Attack". While trying to find a resolution with the VOIP provider I had at times picked up the phone randomly & found the caller on the line. So apparently the calls have no prblem reaching my PAP2T Adapater, it is just that (1) there is no ring when they do & (2) the incoming calls get blocked by Firewall & dropped.
I have tried port forwarding (UDP & TCP) as well DMZ mode for the Adapter, no luck. Later i tried disabling almost all of the internet provider's 2wire modem/router firewall features (UDP ports scan, packets , etc.) still didnt work. I have run out of ideas & hoping that someone can help me find a way out of this problem ? Appreciate your help & time. Thanks.

I changed to the following settings that did the trick for making the phone ring,
Click Regional on the top:
Under Ring and Call Waiting Tone Spec
Change Ring Waveform to Sinusoid
Change Ring Voltage: 90
Change Ring Frequency: 20
However, when I pick up the ringing phone, there is no voice going through the line. Also, as per my VOIP provider instructions, when I dial a local number followed by # sing & hang up in 5 seconds, I don't get any callback either. I have even updated the PAP2T to the latest firmware 5.1.6. Any thing else I can change to get the voice across & get the call back ? thanks for your help again.

Incoming calls - phone not ringing

Hi All,
My landline phone doesn't ring when there is an incoming call. If I test it with my mobile, I can pick it up and the call connects. Outbound calls are also fine. This makes me think it's the ringer signal which isn't getting through.
I have tried the test plug in the main line box (main socket) with an old corded phone which I know works fine elsewhere. I still get no ringing. I have done this with everything else in the flat dis-connected.
Does this mean the fault lies in the main line box and is therefore BT's issue to fix? If so will I be charged for a call-out? I'd like to work those out before getting an engineer out!
Many thanks,
David

Diaaav wrote:
Yes I tried putting the filter in the test socket and still no joy.
So it sounds like a BT problem I'll have to get an engineer out for? Will I be expected to pay for that?
Thanks!
Have you tried it without the filter? in case the filter is at fault.
(If I have helped you in any way to say "Thank You" please click on the star next to the message. Thank You)
If I have solved your Issue please click the "Mark as accepted solution" button.

In incoming calls phone freezes and reboots

Hi
I got my Jelly Bean 4.1 update and whenever there is an incoming call, my Galaxy Nexus phone freezes and reboots when the caller ends the call. Is this a known issue? What can I do to have this issue fixed.
Thank you

Got it fixed. Remove the 4G card out and put it back after ten seconds fixed the issue.
Thanks.

Incoming caller phone rings 2x before my phone does

i just brought a iphone 4s from sprint. this is my first sprint phone so i am not use to they service. The problem im having with my phone is that when i am recienveing incoming phone calls, the phone rings on the other persons line 2 or 3 times before my phone actually starts to ring. Does this happen with all sprint or all iphones because it is really annonying to me. With this happening i miss alot of calls and not able to reject a phone call with begin able to lie and say my phone was off lol..

BUT MINES HAPPEN ALLLLLLL THE TIME SINCE DAY ONE. SOME TIMES WHEN I CALL OUT I HEA CLICKING SOUNDS AND IT TAKES A WHILE FOR MY CALL TO ACTUALLY CONNECT AND START RINGING. SOMETIMES IT TAKES SO LONG I THINK THE PERSON PICKED UP AND II DIDNT KNW. BUT ANYWAY WHAT CAN I DO ABOUT THIS ISSUE CUZ ITS REALLY A NERVE REACKER

Asterisk not seeing incoming calls

I have Skype Connect set up and an asterisk box set up to use it. I can succesfully call out from asterisk, but I do not see any incoming calls on the number assigned to my Skype Connect Profile. If I call the number it rings a few times then gives a busy signal.
Here is my sip.conf:
[general]
context=from-skype ; Default context for incoming calls
allowoverlap=no ; Disable overlap dialing support. (Default is yes)
udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all)
bindport=5060
bindaddr=0.0.0.0
tcpenable=yes ; Enable server for incoming TCP connections (default is no)
tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces)
srvlookup=yes ; Enable DNS SRV lookups on outbound calls
notifyhold = yes ; Notify subscriptions on HOLD state (default: no)
sendrpid=yes
register => 9905XXXXXXXX:[email protected]/9905XXXXXXXX
[skype]
type=peer
context=from-skype
username=9905XXXXXXXX
secret=Redacted
canreinvite=no
insecure=port,invite
dtmfmode=rfc2833
host=sip.skype.com
realm=sip.skype.com
nat=yes
qualify=yes
fromuser=9905XXXXXXXX
fromdomain=sip.skype.com
disallow=all
allow=g729
allow=ulaw
allow=alaw
trustrpid=no
sendrpid=yes
[1001]
type=friend
callerid=1001
canrevinite=no
dtmfmode=rfc2833
mailbox=1001
disallow=all
allow=ulaw
transport=udp
secret=password
host=dynamic
context=default
And my extensions.conf
[general]
static=yes
writeprotect=no
[globals]
TRUNK=Skype
[default]
[from-skype]
exten=>9905XXXXXXXXXX,Noop(${CALLERID(name)} , ${CALLERID(num)})
exten=>9905XXXXXXXXXX,n,Dial(SIP/1001,30,t,r)
exten=>9905XXXXXXXXXX,n,voicemail(100|u)
exten=>281203XXXX,Noop(${CALLERID(name)} , ${CALLERID(num)})
exten=>281203XXXX,n,Dial(SIP/1001,30,t,r)
exten=>281203XXXX,n,voicemail(100|u)
The last 3 lines were my best guess at how to tell it what the incoming call phone # is and I'm not sure it's entirely necessary. Any thoughts?

Dear MRLindstrom,
I am sorry to hear that you are having issues receiving incoming calls to your Skype Connect Online number.
In looking at your Asterisk configuration, I would suggest changing your 'incoming call field' (the last 3 lines you have included below) to your 9905xxxxxxxxxx, rather than 281203xxxx.
Please make that change and let us know if you are able to receive calls.
Thank you,
MariaA
Skype Enterprise Support

PAP-2T, make incoming calls ring in both phones/Lines?

I have a PAP-2T. On this device I have connected two different phones, one connected to Line 1 and the other to Line 2. I have one SIP account with my provider. My provider has configured my account so that I can make two concurrent outgoing calls. My Lines are configured as the following;
Line 1:
Proxy: xxxx.sipserver.xxxx.xx
Outbound Proxy: <blank>
Register: Yes
Register Expires: 3600
Use Outbound Proxy: No
Use OB Proxy In Dialog: No
Make Call Without Reg: No
Ans Call Without Reg: No
Line 2:
Proxy: <blank>
Outbound Proxy: xxxx.sipserver.xxxx.xx
Register: No
Register Expires: 3600
Use Outbound Proxy: Yes
Use OB Proxy In Dialog: Yes
Make Call Without Reg: Yes
Ans Call Without Reg: No
Now, when I receive an incoming call, the phone connected to Line 1 rings. If I configure Line 2 like this,, Ans Call Without Reg: Yes,, the phone on Line 2 rings but not the one on Line 1.
My question is,, can I make both phones ring when I receive an incoming call?
If so, how do I configure the ATA to make that happen?

Cat2k1 what kind of probs do you hve with your phones ?
- assume it's a DECT phone, try to change the ring voltage to 75V and ring waveform to trapezoid - this works better with problematic DECT phones
- assume you're having an old analog phones, make sure the PAP2T's Line1 socket is only connected via 2wire interconnect cable (4wire cable on Line1 plus certain analog phones is a trouble-maker)
- assume you use multiple analog phones on one line, you may consider increase the FXS power from 3 to let's say 5
- assume you're having an old analog phone, it's ability to ring (if all the SIP comm works OK) is also affected by the FXS port impedance which must (shall) fit the phone's one.
====
On the other hand, shall you have problems with SIP communication between PAP2T an SIP operator, you shall enable NAT traversal and NAT keeplalive for the first on PAP2T settings
Message Edited by Scorpio-cz on 12-24-2008 10:50 PM

I am facing issue in Receiving incoming calls, Name not getting displayed though the same has been saved in my phone book!! I have done sync from Windows contacts.. please help if some1 knows how to rectify the issue...

I am facing issue in Receiving incoming calls, Name not getting displayed though the same has been saved in my phone book!! I have done sync from Windows contacts.. please help if some1 knows how to rectify the issue...

Has your carrier been having issues with Call Display? Do the telephone numbers come up when people call, or does it just show 'Unknown Number' or 'Blocked' ?

IPHONE 4S incoming calls go directly to voice mail. This is a brand new replacement phone. Prior phone didn't have this problem

IPHONE 4S incoming calls go directly to voice mail. This is a brand new replacement phone. Prior phone didn't have this problem

Slide up from the bottom of your display to access the control panel.
Look for the button (should be at the top) that shows a crescent moon.
Tap that button. It should say "Do not Disturb: Off".
Then try it out and let us know if it worked.

My iPhone 4 won't take incoming calls. Everytime someone phones me it goes straight to voice mail. What's gone wrong?

For some reason my iPhone 4 won't take incoming calls and everytime someone phones me it goes straight to voicemail what's gone wrong??

Look at the AT&T VVM User Guide for help setting up your visual voice mail.
If you still have problems, contact AT&T Customer Service at 1-800-331-0500 and ask them to check that your account is provisioned for an iPhone 4.

Iphone 4S; Phone & audio piece; Incoming calls are NOT routed automatically??

When I dial out; no problem the calls automatically goes through ear pice.
When I get incomming calls the call goes to phone, not even to the speaker in in the phone. So I have to
1.Slide the bar (then first realizing (again) dam: I hear nothing)
2. Choose the box for speaker options
3. Choose my blue ant piece..
By then some callers think I am not picking up or there is somthing wrong..!
My 3 colleaguers have same phone and no such problems. We are at a loss and I could not find reply in community groups. There was note about Iphone 5 and not correcting to Car speaker automatically. This was noted as a softwre issue Apple might address in next version. But since my colleagues do not have problem with their Iphone it must be either my settings or a weird fault with my phone.
One of my collegues have same ear pice as me, so the issueis not that either.
Is there some weird setting I need to fix to correct the problem?
Thank you

Are you able to make calls? I would try a couple different things -
1. Try doing a double hard reset - Press and hold home button and the sleep wake button at the same time until the screen displays the slide to shut down red button. Continue pressing and holding both the buttons until the screen goes black and then the apple logo flashes up. Continue pressing and holding both the home and sleep wake button beyond this point until the screen goes black again. At this point, let go of the home button and press once the sleep wake button as you would to start your phone. See if this double hard reset helps clear out any cache.
2. If this fails, I would try restoring the phone as a new phone in iTunes. Backup your phone before this so that you dont lose your contacts, etc. You can do a couple test calls once the firmware is installed before setting up the phone, data, apps, etc. If it looks good, try restoring your phone from an earlier backup.
If everything fails, call AppleCare or see a Genius in the store.

No phone icon to answer incoming calls with text message

I have a brand new iPhone 5 with iOS 6.1.4.
When I have an incoming call, I do not get the small telephone icon on the bottom right of the screen, so I have no access to options such as answer with text message. What can be done to activate this?

You search your iPhone for the Phone app and put it back there.
Or tap in Settings > General > Reset > Reset Home Screen layout button

I can make calls and send text messages on my new iPhone 5, but incoming calls and texts still go to my old (non-Apple) phone. Is this a problem with the phone set up, or is it a problem with my old carrier or my new carrier?

I can make calls and send texts on my new iPhone 5, but all incoming calls and texts are received by my old (non-Apple) phone.

Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Try each of these in order until the issue is resolved.

Bought a new phone and now we can not receive incoming calls

This week I bought a new Panasonic cordless handset with no answering machine to replace our AT&T desk phone. I set it all up and waited the 7 hours for it to charge. Checked for dial tone, ringer, and volume. Called the house # from my cell phone and the screen on the Panasonic never showed an incoming call - kicked into voice mail (provided by Verizon) after the preset 5 rings so I left a test message. Panasonic screen showed a "1 new voice mail message". I was able to dial the voice mail access phone # and listen to my test message. Disconnected the new handset and reconnected our old phone - worked just fine. Returned the Panasonic to the store where purchased and exchanged for another (same model). Sales assoc. said there may be a code needed from Verizon. Spent hours on the phone attempting to speak to a real person at the customer service # and decided none work there anymore - everything was automated! After "4 digit pin" frustrations I gave up!
So if you've read this far and can help I'd sure appreciate it! Line works fine, old phone works fine, checked ringer/volume on new phone. Only working phone jack in the house (used to have 2 but when we contracted with V last year they only changed over one - another frustration). And how can I find out when our contract is up?!?

Your mostly talking to peers here. Better off using the
http://www22.verizon.com/support/residential/contact-us/index.htm
option which is on all the Verizon pages. Should always lead you to phone numbers (1-800-verizon) and often an online chat. Sometimes will show you and email option.
As far as peers helping we would need to know what type phone service and general area of the country. Obviously varies as I have had no trouble with panasonic, uniden and other phones at my two locations (NY and FL).

So my I phone 4s volume has decided to pack allowing only my phone to make sounds when I have an incoming call, I can also here fine using facetime and receiving calls. YouTube, soundcloud, any of I players will no longer play sound. I've restored the ph

So my I phone 4s volume has decided to pack allowing only my phone to make sounds when I have an incoming call, I can also here fine using facetime and receiving calls. YouTube, soundcloud, any of I players will no longer play sound. I've restored the phone using iTunes on my laptop and checked all the volumes are turned up and the button at the left hand Side of the phone is in the correct position.

Try inserting and re-inserting your headphones 7 or 8 times. Also try cleaning out the headphone jack in case of debris that might be interfering with the connection/disconnection.

PAP2T - Incoming Calls/Phone Compatibilty!

Similar Messages

Maybe you are looking for