Parallel port printer modules not loading autmatically

According to the wiki entry for CUPS, either the kernel or or a small configuration file in /etc/modules-load (not /etc/modules-load.d) is supposed to automatically load these modules on boot. When I run lsmod I'm finding none of the printer modules (lp, parport, parport_pc) are getting loaded even though the printer is attached and powered up. Any idea why these modules are not loading? They load perfectly well manually with the modprobe command.
As the wiki specifies, I do have a configuration file in place at /etc/modules-load/printing.conf with the following contents:
lp
parport
parport_pc

Commenting out the INSTALL lines in modprobe.conf worked perfectly.
Before that i tried the stock kernel form current and am now using the one from testing. Neither worked with sound while the INSTALL lines were ther.
What changed?

Similar Messages

How to Install a parallel port printer to usb port of Pavilion dv5 Notebook

In trying to install my HP DeskJet 610C Parallel Port printer to my HP Pavilion dv5-1235dx Notebook PC with Windows Vista Home Premium 64-bit, I followed instructions given by HP Support some two years back.
I connected up the two units through a Parallel-to-USB ports cable. The PC loaded and confirmed suitable driver. (Following advice from sites on the Internet, I have made repeated attempts to carefully install the printer, but to no avail).
Upon my issuing the Print instruction, the printer invariably prints two copies of what appears to be 'gibberish' in two lines at the start of the sheet. Thereafter it picks up and then ejects 6-8 sheets of blank paper.
Any help in resolving this anomalous situation will be be most welcome and much appreciated.
I might add that the printer works normally when connected in parallel to an older, Compaq Armada 1750 Notebook (XP OS). In this instance too, the Parrallel/USB worked as in the Pavilion PC, above.
This question was solved.
View Solution.

Hi khalidem,
Sounds like you have a communication problem with the printer cables. Have you tried a new parallel to USB cable or adapter?
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"

Satellite A200: How connect a parallel port printer?

Probably a very silly question, but would like to connect A200 series laptop to a parallel port printer that does not have a USB port... what is the best option?

Hi
You ask for the best way?
Well, you have got only one way?
You need an USB to parallel adapter. Check in the google for some offers.
I searched in the google and found some good options.
Maybe this could be a good choice;
http://www.ramelectronics.net/html/usb_printer_cable.htm#UP6C
Best regards

Connect parallel port printer to usb in windows 8.1 64 bit

I am using Windows 8.1 w/ 64 bit - would like to know proper cable to hook up to parallel port printer HP LaserJet 4050. Any help greatly appreciated.

@PB1941
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

How should I develop Level Controller using Parallel port(Printer port)

I need to develop a level controller using parallel port of my computer with a third party Data Acquisition Device. Is it possible to do it with In and out port vi in labView 7.1. Please guide me how can should I configure these Vis to write control data and then receive level transmitteed data through parallel Port(Printer port). My third party DAQ has two analog input channel and one analog output channel.

Dennis Knuston
I have uploded the details of that third party daq in another thread please see that and tell wether this type of daq requires driver software
http://forums.ni.com/t5/Multifunction-DAQ/Parallel-port-based-daq-and-drivers/m-p/1819997

Parallel port printer connection

I have an HP 6122 parallel port printer which I've attached to my MacBook Pro running on OSX 10.4.11 through a connecting cable to the USB port (I've tried both the left and right USB port). I've downloaded driver from HP, but computer doesn't see the printer. Suggestions?

Hi urdog, and a warm welcome to the forums!
In System Profiler>Hardware>USB, is anything shown for it there?
Have you tried another PCL/hp printer in Printer Setup Utility? Have you got any hp drivers installed?
PCL 3 is quite old, but what happens if you try setting it up with an older hp driver?

Error When Publishing "no access to internet (internet module not loaded)"

When publishing a site in GoLive 9 I get the message""no access to internet (internet module not loaded)".
i've never had this problem before, this just started happening and cant figure out how to get it to work again. it's weird because i can connect to my ftp server from the file menu and the internet module is checked on in my preferences. i've tried creating a new site file for my webpages and reinstalling GoLive and nothing has worked.
has anybody had the same problem? thx!

ha, ok i just figured it out. i didn't have the proper ftp setting in the publish preferences. i hadn't changed the info in the "server name" from the place holder text that was automatically inserted. that's a strange error message to display for that!!!

C8180 error says two side print module not installed but i have used it before

my c8180 printer error says two side print module not installed but i have used it before.i reinstalled printer with cd but did not help. Jean

What operating system? The duplexer typically must be enabled (just once...) in the driver to make it available. Enable the duplexer as shown in the Vista/Win 7 Duplex Printing Troubleshooting Guide here.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Parallel Port & Printing

Hi,
I am new to ArchLinux and have been using Gentoo since qutie a while. After installing nearly everything I need I am now struggling with the printer setup. I guess this is due to a problem with my parallel port, cause it does not show up in the selection box of cups. I can choose serial and usb ports, but no parallel ports. I have installed some modules like
lp & parport
I also have cups running of course and it connects. My question is the kernel (2.6.4) must be compiled with support for the parallel port by default, right? At least after loading these modules it should work. What am I missing?
Thanks already!!!

Good advice! Haven't solved it yet, but FWIW I can read the cups documentation. So I set the log to debug mode and here it is:
This log content follows
lp fstab
18/Mar/2004:18:13:15 +0000] AcceptClient() 5 from localhost:631.
ReadClient() 5 POST / HTTP/1.1
ProcessIPPRequest: 5 status_code=1
CloseClient() 5
AcceptClient() 5 from localhost:631.
ReadClient() 5 POST / HTTP/1.1
ProcessIPPRequest: 5 status_code=1
CloseClient() 5
AcceptClient() 5 from localhost:631.
ReadClient() 5 POST / HTTP/1.1
ProcessIPPRequest: 5 status_code=0
ReadClient() 5 POST /printers/lpr HTTP/1.1
print_job: auto-typing file...
print_job: request file type is text/plain.
check_quotas: requesting-user-name = 'root'
print_job: requesting-user-name = 'root'
Adding start banner page "none" to job 16.
Adding end banner page "none" to job 16.
Job 16 queued on 'lpr' by 'root'.
Job 16 hold_until = 0
StartJob(16, 0x8093b70)
StartJob() id = 16, file = 0/1
job-sheets=none,none
banner_page = 0
StartJob: argv = "lpr","16","root","fstab","1","","/var/spool/cups/d00016-001"
StartJob: envp[0]="PATH=/usr/lib/cups/filter:/bin:/usr/bin"
StartJob: envp[1]="SOFTWARE=CUPS/1.1"
StartJob: envp[2]="USER=root"
StartJob: envp[3]="CHARSET=iso-8859-1"
StartJob: envp[4]="LANG=en"
StartJob: envp[5]="PPD=/etc/cups/ppd/lpr.ppd"
StartJob: envp[6]="CUPS_SERVERROOT=/etc/cups"
StartJob: envp[7]="RIP_MAX_CACHE=8m"
StartJob: envp[8]="TMPDIR=/var/spool/cups/tmp"
StartJob: envp[9]="CONTENT_TYPE=text/plain"
StartJob: envp[10]="DEVICE_URI=parallel:/dev/lp0"
StartJob: envp[11]="PRINTER=lpr"
StartJob: envp[12]="CUPS_DATADIR=/usr/share/cups"
StartJob: envp[13]="CUPS_FONTPATH=/usr/share/cups/fonts"
StartJob: envp[14]="CUPS_SERVER=localhost"
StartJob: envp[15]="IPP_PORT=631"
StartJob: statusfds = [ 7 8 ]
StartJob: filterfds[1] = [ 9 -1 ]
StartJob: filter = "/usr/lib/cups/filter/texttops"
StartJob: filterfds[0] = [ 10 11 ]
start_process("/usr/lib/cups/filter/texttops", 0xbffeff30, 0xbffef2a0, 9, 11, 8)
Started filter /usr/lib/cups/filter/texttops (PID 2486) for job 16.
StartJob: filter = "/usr/lib/cups/filter/pstops"
StartJob: filterfds[1] = [ 9 12 ]
start_process("/usr/lib/cups/filter/pstops", 0xbffeff30, 0xbffef2a0, 10, 12, 8)
I [18/Mar/2004:18:13:15 +0000] Started filter /usr/lib/cups/filter/pstops (PID 2487) for job 16.
StartJob: filter = "/usr/lib/cups/filter/foomatic-rip"
StartJob: filterfds[0] = [ 10 11 ]
start_process("/usr/lib/cups/filter/foomatic-rip", 0xbffeff30, 0xbffef2a0, 9, 11, 8)
Started filter /usr/lib/cups/filter/foomatic-rip (PID 2488) for job 16.
StartJob: backend = "/usr/lib/cups/backend/parallel"
StartJob: filterfds[1] = [ -1 9 ]
start_process("/usr/lib/cups/backend/parallel", 0xbffeff30, 0xbffef2a0, 10, 9, 8)
Started backend /usr/lib/cups/backend/parallel (PID 2489) for job 16.
ProcessIPPRequest: 5 status_code=0
This looks like the problem? Can't find status 22 explanation but must be the next line.
PID 2488 stopped with status 22!
[Job 16] /usr/lib/cups/filter/foomatic-rip: No such file or directory
[Job 16] Page = 612x792; 0,0 to 612,792
[Job 16] ppd->num_fonts = 35
[snip]
[Job 16] ppd->fonts[8] = Courier
[Job 16] Page = 612x792; 0,0 to 612,792
[Job 16] slowcollate=0, slowduplex=0, sloworder=0
[Job 16] 0 %%BoundingBox: 0 0 612 792
[Job 16] 0 %%Creator: texttops/CUPS v1.1.20
[Job 16] 0 %%CreationDate: Thu Mar 18 18:13:15 2004
[Job 16] 0 %%Title: fstab
[Job 16] 0 %%For: root
[Job 16] 0 %%Pages: (atend)
[Job 16] 0 %%DocumentNeededResources: font Courier-Bold
[Job 16] 0 %%+ font Courier
[Job 16] 0 %%DocumentSuppliedResources: procset texttops 1.1 0
[Job 16] 0 %%+ font Courier-Bold
[Job 16] 0 %%+ font Courier
[Job 16] 0 %%EndComments
[Job 16] 0 %%BeginProlog
[Job 16] 0 %%BeginResource: font Courier-Bold
[Job 16] 0 %%CreationDate: Wed Dec 22 1999
[Job 16] 0 %%EndResource
[Job 16] 0 %%BeginResource: font Courier
[Job 16] 0 %%CreationDate: Wed Dec 22 1999
[Job 16] 0 %%EndResource
[Job 16] 0 %%BeginResource: procset texttops 1.1 0
D [18/Mar/2004:18:13:15 +0000] [Job 16] 0 %%EndResource
[Job 16] 0 %%EndProlog
[Job 16] 0 %%Page: 1 1
[Job 16] 0 %%Page: 1 1
[Job 16] pw = 612.0, pl = 792.0
[Job 16] PageLeft = 0.0, PageRight = 612.0
[Job 16] PageTop = 792.0, PageBottom = 0.0
[Job 16] PageWidth = 612.0, PageLength = 792.0
[Job 16] 0 %%Trailer
[Job 16] Saw Trailer!
[Job 16] Saw EOF!
UpdateJob: job 16, file 0 is complete.
CancelJob: id = 16
StopJob: id = 16, force = 0
StopJob: printer state is 3
CloseClient() 5
Bill Barnes

Java - Parallel Port Printing

Hi there
i have connected a DOT- MATRIX printer to my parallel port.i opened port lpt1 as if it were a file .Printing is fine. But if the printer is offline or disconnected my program does not throw an exception.I need to find out whether the printer is connected or not..
Regards
Raghavendran

Might this be because of the windows print spooler? Or have you turned that off?

Modules not loading in Flex 4

Hi All,
I have migrated my application from Flex 3 to Flex 4. My application has 3 different modules. The modules are not loading when I run my application with Flex 4. Please help me in this respect.
Thanks in advance,
Nirmal Kumar Bhogadi

Hi Nirmal,
Right click on the project and go in Properties. On the left bar, go in the Flex Modules tab and check if your modules are present there.
If not, browse your modules from the project and add them one by one.
Regards
Monika

[SOLVED] Modules not loaded after upgrade linux (3.9.5-1 - 3.11.6)

Hi. After upgrading the package linux from 3.9.5-1 to 3.11.6,
many modules such as wifi or psmouse are not loaded.
My PC is Asus Zenbook UX31E.
If I do by hand like
# modprobe ath9k
# modprobe psmouse
wifi and psmouse are OK,
but I want to set all necessary modules auto loaded.
* Output of lsmod of linux 3.9.5-1 was 87 rows
but lsmod of 3.11.6 (I attache below) is only 39 rows.
* Both
/etc/modprobe.d/
/etc/modules-load.d/
are empty on 3.9.5-1 and 3.11.6.
Please give me advice, thx.
Last edited by taro (2014-01-08 11:20:46)

Thx. The version numbers seem to be identical.
% uname -a [~]
Linux tenryu 3.11.6-1-ARCH #1 SMP PREEMPT Fri Oct 18 23:22:36 CEST 2013 x86_64 GNU/Linux
% pacman -Qi linux [~]
Name : linux
Version : 3.11.6-1
Description : The Linux kernel and modules
Architecture : x86_64
URL : http://www.kernel.org/
Licenses : GPL2
Groups : base
Provides : kernel26=3.11.6
Depends On : coreutils linux-firmware kmod mkinitcpio>=0.7
Optional Deps : crda: to set the correct wireless channels of your country
Required By : None
Optional For : None
Conflicts With : kernel26
Replaces : kernel26
Installed Size : 64493.00 KiB
Packager : Thomas Bächler <[email protected]>
Build Date : Sat 19 Oct 2013 06:25:12 AM JST
Install Date : Fri 08 Nov 2013 12:06:17 PM JST
Install Reason : Explicitly installed
Install Script : Yes
Validated By : None
best regards.

[Solved]Virtualbox kernel module not loaded

I update my system today and when I try to run Virtualbox...
WARNING: The vboxdrv kernel module is not loaded. Either there is no module
available for the current kernel (3.6.11-1-ARCH) or it failed to
load. Please reinstall the kernel module virtualbox-host-modules or
if you don't use our stock kernel compile the modules with
sudo dkms autoinstall
You will not be able to start VMs until this problem is fixed.
I already had this trouble before and this was the fix
# modprobe vboxdrv
But it doesn't work anymore
Any ideas?
Edit: This just get fixed by itself when restaring my PC. Sorry
Last edited by ilq (2013-02-13 02:32:43)

fsckd wrote:
rc.conf is part of the deprecated init system. icebox is not using systemd and neglected to mention that.
Amarildo, see the wiki.
Thanks, it really helped. It's solved.

PDF printer driver not loading

Ok...first off I had CS on another laptop and the driver was there. Got new laptop loaded CS and PDF printer didn't load up. Second. I got and loaded CS3 (not just because of the lost printer driver, but...) and loaded it onto the same *new* laptop and STILL not PDF printer driver. I've looked at the downloads and can't find it available there. This is driving me nuts. I develop proposals and other documents in word (not to mention the PIA factor of not being able to print directly to PDF in AI or PS) and have to dump files to a shared directory so that I can use Acrobat Pro 6 on a desktop before sending out to clients. Arrrrrgghhh (and yes, I know that Talk Like a Pirate Day isn't until Sept 19th.)
I have tried reinstalling or 'fixing' ABPro umpteen times now and find myself fulfilling Einstein's definition of insansity. Any ideas on what I can do to get a *&^%# PDF printer driver to load?

Hi Daniel,
I´m using AutoVue 3D Professional Advanced 20.2.0.... I´ve read that there were problems
in the version 19.xx (before version 20.xx)
Best,
Merkowitsch

Usbser_edge module not loaded, lots of undefined symbols

Greetings folks,
I've just recently more or less completed my Solaris 10 (sparc) jumpstart image and have noticed that upon booting the system will warn about undefined symbols for the usbser_edge module. I've been hunting around and I can't seem to find out where this module is specified to be loaded. The machine in question is a 220R, and I'd like to figure out how to not load this module so the warnings will go away:
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/misc/sparcv9/usbser: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_dprintf0'
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/misc/sparcv9/usbser: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_dprintf1'
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/misc/sparcv9/usbser: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_dprintf2'
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/misc/sparcv9/usbser: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_free_log_hdl'
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/misc/sparcv9/usbser: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_alloc_log_hdl'
Sep 9 09:33:25 jump-test krtld: [ID 472681 kern.notice] WARNING: mod_load: cannot load module 'usbser'
Sep 9 09:33:25 jump-test krtld: [ID 749970 kern.notice] WARNING: usbser:
Sep 9 09:33:25 jump-test krtld: [ID 225575 kern.notice] unable to resolve dependency, module 'misc/usba' not found
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_lookup_ep_data'
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_parse_data'
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_dprintf0'
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:25 jump-test krtld: [ID 826211 kern.notice] 'usb_dprintf2'
Sep 9 09:33:25 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_ctrl_xfer_wait'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usbser_close'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usbser_power'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_sync_ctrl_xfer'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_alloc_intr_req'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usbser_getinfo'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_close'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_unregister_event_cbs'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_reset'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_bulk_xfer'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_free_bulk_req'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_register_event_cbs'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_free_intr_req'
Sep 9 09:33:26 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:26 jump-test krtld: [ID 826211 kern.notice] 'usb_free_log_hdl'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_stop_intr_polling'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usbser_attach'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usbser_detach'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usb_get_dev_data'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_open'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usb_alloc_log_hdl'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usbser_rsrv'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usbser_wsrv'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usbser_wput'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usbser_open'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usb_check_same_device'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_intr_xfer'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usb_create_pm_components'
Sep 9 09:33:27 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:27 jump-test krtld: [ID 826211 kern.notice] 'usb_free_descr_tree'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_set_device_pwrlvl0'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_set_device_pwrlvl1'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_set_device_pwrlvl2'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_set_device_pwrlvl3'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_pipe_get_max_bulk_transfer_size'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usbser_soft_state_size'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_alloc_bulk_req'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_handle_remote_wakeup'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_client_attach'
Sep 9 09:33:28 jump-test krtld: [ID 819705 kern.notice] /kernel/drv/sparcv9/usbser_edge: undefined symbol
Sep 9 09:33:28 jump-test krtld: [ID 826211 kern.notice] 'usb_client_detach'
Sep 9 09:33:28 jump-test krtld: [ID 472681 kern.notice] WARNING: mod_load: cannot load module 'usbser_edge'
Sep 9 09:33:28 jump-test krtld: [ID 749970 kern.notice] WARNING: usbser_edge:
Sep 9 09:33:28 jump-test krtld: [ID 225575 kern.notice] unable to resolve dependency, module 'misc/usba' not found
Thanks in advance for any advice anyone can provide.
pb

I just attempted a generic search at Sunsolve, for "usbser_edge".
It produced references to a lot of documents available after contract login to the site.
If you have a Spectrum login account, get to BugID 4703982.
It's from 2003 or so...
but it discusses the SUNWuedg package being incorrectly installed,
on beta versions of Sol-10, to an E250 and to a SB1000.
Other search result references to various BugID's also happened to discuss
removing references to the driver in the /etc/name_to_major file
as well as in the /etc/driver_aliases file.
See BugID 4790469 or BugID 5045102
I don't trust my skill level with mucking around with such files, however.
If you have contract coverage for the OS or for that system, open a support case.
If not, then see if the SUNWuedg package is installed and remove it.
Then a reconfiguration reboot may be in order.
What the heck, try a reconfiguration reboot just for grins and giggles.
... just my two cents, at least.

Parallel port printer modules not loading autmatically

Similar Messages

Maybe you are looking for