PART 2 ledger posting problem

Hi All,
I n SAP CIN (Country Version India) J1IEX (Excise invoice part 2) posted .
Part 1 ledger got updated but part 2 value is coming as 0 while checking in J1I7.In MIGO base value and excise duties are captured correctly.
How to get the values updated in Part 2 ledger?
Please help me inthis regard.
Thanks

Hi,
check your Migo and excise tab click on that and check status of your excise invoice there
and in J1I& check your selection parameter like excise group and material should be correct
Regards
Kailas Ugale

Similar Messages

Having a problem in iBooks. When I highlight a section I would like to copy the highlighted parts sometimes to post in my notes. Can't seem to get it to work. Any ideas?

Having a problem in iBooks. When I highlight a section I would like to copy the highlighted parts sometimes to post in my notes. Can't seem to get it to work. Any ideas?

Just noticed the same problem. I was able to do it before updating. Hope there's a simple answer. That is a big reason why I got the iPad and iBooks.

Part 1 not Post for excess of qty

Hi.
I have one problem during STO
When i despetch 1 Material total of 108 KG in different batch say B1(40),B2(41) and B3(27)
I make delivery say DEL1
I make excise invoice say EXC1 for qty 108 for three batch
when i go for MIGO against outbound delivery DEL1 and enter excise invoice EXC! with Part 1 system shows me error message Part 1 not Post for excess GR qty
and in excise tab it shows qty for 1 batch only say B3 for all item tab.
Thanks & Regards
Chetan

Dear,
Two way,
1) Cancel Good receipt document with MIGO t-code and create new document for material receipt and capture part 1.
2) Go J1IEX - capture excise invoice against your material document.
Than post it with J1IEX.
Regards,
Mahesh Wagh

Wrong GR, Part II also posted

All SAP Gurus,
We have posted the wrong GR (by mistake).
Part I cptured during GR (MIGO).
Part II also posted.
Now, we came to know that there is problem with GR, so we want to reverse GR and Excise entries.
What are the steps to be followed?
Regards,

Hi
Cancel the GR document if usage decision is not done. for Excise post the document using transaction J1IEX and then cancel the document with same trasaction.
If usage decision is done by quality the do the return delivery and create out going excise invoice using transaction J1IS.
Thanks & Regards
M P D Kamath

Alternative to posting problem reports via OSS?

Sometimes I find problems with SAP software, like the RFC library, that I'd like to be able to report, however I'm not always in a position to do so, as I may not be working at a client site at the time (and it would not be appropriate to log the problem under their installation).
What is needed, IMO, is a way to log these problems without the formality surrounding OSS and SAPnet. I imagine this would be important too for those coming into SAP for the first time from the Java side.
Perhaps the easiest way would be to mark a forum posting as a problem report, similar to the way it can be marked as a question. This would then allow for highlighting to forum members from SAP who could decide whether the problem warranted escalation.
Cheers,
Scott

Hi Scott,
i agree. There should be a possibility to create a linkage between OSS notes and SDN postings in some cases, because (besides or in addition what you've already said):
1. Problems which are reported to OSS might already have been resolved in SDN and vice versa. A common knowledge repository would be very helpful for both parties, i guess. In my opinion it's easier (and cheaper) to <b>verify</b> a possible solution published already in SDN than finding/creating a new one for OSS.
2. IMHO it's probable that a steadily increasing number of "productive versions users" of arbitrary SAP software components will start to post problems and possible bugs at the SDN forums in the near future. It's absolutely ok to redirect them to the OSS, since this is the official place to report and handle such issues.
But it should be possible for example to add a link referring the "SDN problem thread" to the customer message(s). The support team could then post the SAP notes number as a reply to the thread as soon as a solution is available. Otherwise, if people aren't gentle enough to return to the forums and publish the problem solution, it's not easy to find the official answer, since nobody knows how to search for the corresponding note to get reliable search results. If the problem description of the note doesn't repeat parts of the question text in SDN, you are lost.
3. Resulting from 2., more and more "information leaks" will arise in the SDN forums. But i dare to argue that people will return asking the same question(s) over and over again, if there's enough interest, until "somebody" is lucky enough to find the solution in the OSS and post the notes number. Why not "automate" this?
Just to clarify:
I do <b>not</b> want to have the OSS team bypassed, this is definitely wrong from my point of view.
Cheers,
Stefan

Non Leading Ledger Posting

Hi Guys,
Have client requirement in Non-Leading Ledger.
For MIS reportting purpose Non Leading Ledger using, dont impact on Leading only for MIS purpose post some Entryes. FB50L use for Non Leading Ledger Posting.
1. Normal Expenses booking every month - No issues
2. Provision book for Customer & Vendor every month dont impact on any logal Books - In this case is it possiable manual JV ?
I tested one scenario Normal Expenses booked in FB50L 2012 8 period Document Type is SA. If saw in FAGLFLEXT Table 2012 - 8 period no values it is coming only in 16 period only.
3. Will book any Manual JV Expenses book in FB50L Non leading ledger will show 16 period only ? or any setting is wrong.
4. Will book any Expenses in FB50 Leading automatically updating in Non Leading Ledger will see in FAGLFLEXT Table same value showing under 16 period only.
If i check in FAGLFLEXA Table is showing correctly 2012 - 8 Leading & Non-Leading (FB50L)
5. We are using 30 company codes in 30 Countryes. Currency Keys is 10, 40, 60- USD. 60 is common currency for all co.Codes. issue is i developed one report in Report painter Used FAGLFLEXT Table. 60 Global Company Currency is not updating.
Please provide the soluation on above points it is very urgent.
Thanks
Ramu

By default system will post to all ledgers that is leading and non leading ledgers for a posting. However you can make postings to non leading ledgers independent of leading ledgers using Fb50L which should not be open item managed.
Non leading ledger will contain all postings of leading ledgers + postings related to local reporting requirements.
There is no way that you can control this in my opinion using SAP standard functionalities.

Web Part Page check in problem

I created a simple web part page that contains a web page viewer web part. I filled out all available fields during creation. It was stored in the default Shared Documents folder. I can link to the web part page with no problems. However, others can't because it is check out to me. When I try to check it in, I get the "You must fill out all required properties before checking in this document" error. When I click "Edit Properties", everything is filled out. I noticed that if I click "View Properties", a "Title" field is visible. How can I fill this out??? It wasn't available during creation and I have no idea how to fill it out because it doesn't show up after clicking "Edit Properties. This seems really buggy.

I currently have this problem running wss3.0 in a portal I have created. Two existing document libraries contain web part pages which do not require check in/check out. However in the last day or two, every new page created is automatically checked out to myself, but I cannot check the item back in. I have the following show up:
"You must fill out all required properties before checking in this document."
I have followed the procedures above to add the web part as an extra content type to the list, and hiding the title column so its not needed, but i still receive this error message. It only seems to be happening on this particular portal, and not others. The fact exisitng pages in the document library do not require items to be checked out makes it very frustrating trying to resolve. Ive searched TechNet but cant find any more details. I've even tried to force check in using Sharepoint Designer but this also does not work.
Does anyone have any ideas? Every new document library i create contains checked out items for this portal now, so others cannot view.
thanks,

HttpServletRequest getReader read part of the post data

Hi all,
HttpServletRequest getReader read part of the post data (even though the conten length is bigger).
It stops after 48k (49,152 bytes)
int sizeOfBuffer = 100;
char[] cbuf = new char[sizeOfBuffer];
StringBuffer inputBuffer = new StringBuffer();
BufferedReader reader = request.getReader();
int chars = 0;
while ((chars = reader.read(cbuf)) >= 0) {
inputBuffer.append(cbuf, 0, chars);
reader.close();
inputBuffer includes parts of the data??
Can anyone help me to know what is wrong??
Thanks,
Lior.

Hi Jakub,
Yes, you can query TDM files for samples with certain specifications. Take a look at this Tutorial Introduction to LabVIEW Data Storage VIs. The section on Query Conditions demonstrates how to look for select samples using the Data Storage express VIs.
I hope this is helpful. Please post if you have further questions!
Cheers,
Megan B.
Applications Engineer
National Instruments

General Ledger Posting Error (GLT2 051) No accounting transaction variant

Hello SAP Gurus-
When testing lockbox in FLB2, I received the following error message:
General Ledger Posting Error (GLT2 051) No accounting transaction variant assigned to FB01/ /LB
We are on ECC 6.0
I created a new Document Type LB
I created a new G/L account for Lockbox clearing and AR
How do I fix this?
Thank you!

Hi,
Assign a transaction variant for the document type you created in Transaction code GSP_VZ3. Also, make sure that the GL accounts affected are assigned with item categories in GSP_LZ2.
Thanks
Aravind

P45 Diamond Post Problem

Hi,
I'm starting to have another post problem with my P45 Diamond motherboard. (First one was RMA'd). This time, it's showing "Processor Initilization" with red, green, green, red. My current system is
Motherboard - MSI P45 Diamond
Bios - 1.3
Processor - Intel Q6600 (older version)
Memory - Kingston KVR1333D3N9K2/4G 4gb total 1333
Power Supply - Silverstone 750 watt
Graphics - ATI Radeon HD 3870 X2
It's been working fine for a few weeks and just started acting up. I'm using stock settings (no overclock) .
Recent changes are adding the Genie, however the post problem happened for the first time before I plugged in the Genie. The same result now occurs when the Genie is plugged in and when I remove it from the motherboard power.
Basically what happens is it will power up for the first time and it works. If I restart or shutdown and turn it back on the monitor stays blank and the status lights show Red, Green, Green, Red which is Processor Initilization. Only way to get it to boot up is hitting the Clear CMOS button or, when I went to bed and started it up this morning, it booted fine.
Any suggestions would be greatly appreciated.

Quote
The MCH voltage in Core Center we being reported at 1.976 however I NEVER changed any of the values. Is it possible that the bios "AUTO" changed the value?
The question is this value is really set to 1.976V or if it just a misreport. Please start Green Power Center and check the voltage values there.
{Remove Dual Core Center from the AUTOSTART list to make sure it does not open automatically when Windows is loaded. You can start Green Power Center independently of DCC. Just have look at the Dual Core Center Installation folder. There should be a sub-folder that contains the GPC Application. Create a shortcut to it from the Desktop and you are ready to go.}

K7T Turbo2 Post problem

Hey all, first time here. I am trying to fix my son's computer for Christmas. His old mobo went dead and I picked up a K7T Turbo2 at the local shop. Details below:
K7T Turbo2 mobo - Award BIOS v6.00PG (W6330VMS v3.7)
AMD Athlon 1.4
2 x PC100 128MB ram
AGP GeForce4 MX (tried Rage 128
WD 40GB hdd
Standard 52x CD
Macron PSU 300W
When booting the first few times, it acts like it wants to boot, gets through post and tries to access the hdd - but never gets to any MS booting screen (XP loaded on hdd) - screen just goes black. I turn it off and back on and it gets to the point where it does the HDD check and freezes. The diagnostic LED stops on #1 red and the rest green (manual says boot attempt, but it hasn't even done a hdd check yet). I take it down and back up again several times. Sometimes the LEDs stop on #2 red and the rest green (manual says floopy init).
I took the board back to the shop and got another with the same results. I have tried different AMD 1.4 (from a known working PC), different PC100 128MB sticks and PC133 256MB sticks. I've tried booting with only minimal parts attached (no hdd or cd) with the same results. The only thing I can think of is the PSU is not strong enough. I've tried plugging in the little 12V piece and not using it with the same results. HELP!!!! Tomorrow is Christmas and my son is going to be very disappointed. TIA!
AirGator

Just wanted to say thanks for all the help. I foud the problem though. It was a faulty CPU. I know that I had swapped it out with my working AMD 1.4, but for some reason, this one would die once any load was put on it. I took my wife's 1.4 out and the mobo booted.
I just went out to ZipZoomFly (from Pricewatch) and bought two new AMD Athlon XP 1800+'s for $48 each. Hopefully they'll come in quickly and I can get my son's PC back to him before the end of his Christmas break. Thanks again all!
AirGator

KT6 post problems

Having problems gettting my KT6 to post...Had replaced a PC Chips board with a KT6 thinking it was a dead board..but after installing msi board still have same problems..it wont post..fans on cpu and vga card spin but no boot.. have done a minumal boot outside case..that didnt help..everythings hooked up right..both power cables hooked up...and all..but cant seem to get it to boot..thought it might be my cheap power .. supply so i replaced it with a Antc Smart Power at 350 watts,thinking cpu wasnt getting enough juice but that didnt help...the 4 led error light come on when i turn power but stays on..manual says that means cpu is installed wrong or damaged. I reset cpu and used artic silver and put heat sink on..still no good...Since ive replaced just about everthing except cpu thats gonna be my next purchase..a AMD Atthlon X 2500 ..tried with different stick of memory..used one outta my dell...different vga card..didnt help....
MSI KT6 board
Amd Athlon XP 2600 333mhz barton core
256 DDR PC2700 333mhz...PNY..
Asylum Geforce FX 5200 256 megs
Antec Smart Power SL350 350watts

it did the same thing...with the pc chips board the cpu fan and vga card fan would spin..but it would not boot..hard drive would power up but if i connected ide cable it did nothing..after doing a minimal bot outside case decided it was a dead board...bought a new kt6 board and installed it and it did same thing.fans run but would not boot or make any error code beeps..used the 4 led lights and they show 4 red staying on...and manual says either cpu not set right or faulty..ive reseated it and it just wont work...since ive replaces just about everything with name brand quality parts the last thing it could be is the cpu..just to add this PC Chips board and athlon xp 2600 was part of a barebones pc i bought off line..so it
was tested by company but when it showed up the heatsink was flopping around in case...lol..so when it didnt work wasnt quiet surprised ..but i was sure it was a damaged motherboard..and cpu would be fine..must have been wrong..cpu must have took some damage when heatsink came off during shipping..

New thread posting problem using Mozilla 1.3.1

I am using IE 5.1.7 to post this question.
Using Mozilla 1.3.1, when trying to post to this forum, I can get all the way to PREVIEW or POST MESSAGE, but when I click the buttons the screen acknowledges I have clicked the button and the info at the bottom of the screen indicates it is waiting for an answer from Apple Discussions. Then it says done, but it doesn't post or it doesn't give a preview. What it does do is add some HTML code to the bottom of the unposted message.
Does anyone else have this problem with Mozilla?
Cube G4 Mac OS 9.2.x

Hi, Lawrence. I suspect what you're seeing isn't a browser problem, but a result of work being done on the Discussions themselves. There are a number of current problems being worked on by the Hosts and their elves, and one of them may have some fingers inside the part of the patient you're looking at. I'd sit tight and see what happens in the next couple of days.

BFG 6800 Ultra causes K8N Neo2 Platinum to not POST - Problem finally resolved!

I'm able to run with an ATI Radeon 9700 Pro and a PNY 6800 GT with no problems, but as soon as I plug in my BFG 6800 Ultra I can't get it to POST. The D-Bracket indicates it's doing "Processor Initialization". I don't see any output at all even though steps prior to "Processor Initialization" should be writing a few things to the screen. I should be getting plenty of power as I've got a good PSU and have two of the lines going to the BFG and nothing else. I've tried using several different combinations of lines as well so that doesn't appear to be the problem. I've already changed all the usual suspects in BIOS that might affect the AGP. I've also put the BFG in a crappy Dell system with a crappy PSU and it handled it just fine.
Anyone got any suggestions? I can't seem to find anyone else reporting this problem so apparently I'm the lucky one. Pleeeeeaaaaase! Someone help me fix my problem!

Keep in mind that not all Motherboards regulate their VCore and VDimm almost entirely from the 12v rail. However while it does task that rail it does provide a way for the manufacturer to provide more stable voltages and power. So different boards will react slightly different based even on the same exact set of parts. With so many parts needing 12v these days you have to make sure the PSU is up to supplying enough for everything.
The second thing is how differently each MB sets up in Bios. This can have quite an impact on RAM timings. Loosen up the timings a tad and maybe things will also go a tad easier. However if you can't get any poost then you may have to try an older stick of something like PC2100 or somesuch so that you can enter Bios and set appropriate timings for the RAM you want to use.
Third you can read the various stickies like Basec Building tips to help you get things properly setup.

Exit for to restict Non-leading ledger posting periods for Document Type SA

Hi,
Please give the guidelines to complete the following requirment.
In SAP FI two ledgers Leading(0L), Non-Leading (J2) Posting periods are defined in OB52.
If non-leading ledger is closed also it will take the Leading posting periods and Posting the document..
This is the SAP Behaviour.
Like in FB50L if we enter J2 (Non-Leading) it will display the erro message like
Posting period in not open.
Like that they want for FB70,FB75,MIGO,MIRO,FINT and Invoice(VF01).
Please suggest the suitable exit.
Thanks & Regards,
Padmaja.

Hi Ramu,
Please refer the below points,
1. Leading ledger is only one ledger in one client.
2. In one client you can keep N of non leading ledgers.
3. company codes are need assign to non leading ledgers.
4. All postings will update leading ledger by default.
5. Non leading ledgers will update if company code is assigned to non leading ledger.
6. If you want to post only non leading ledger then please use the tcode FB50L and FB01L.
7 You can set the separeate fiscal year variant for non leading ledger.
I hope above information will resolve you r issue.
Regards
Madhu M
http://wiki.sdn.sap.com/wiki/x/JghNCw    (NewGL Migration Secnarios)
http://wiki.sdn.sap.com/wiki/x/mosOD     (Document Splitting Wizard)
http://wiki.sdn.sap.com/wiki/x/f4OfDg    (NON-LEADING LEDGER SPECIFIC
                                                              POSTING)

PART 2 ledger posting problem

Similar Messages

Maybe you are looking for