Partial collection Failure for nexus 5548UP in PI 2.1

Hi there,
I get "Partial Collection Failure" in the inventory collection status in Prime Infrastructure for all my Nexus 5548UP (8 devices).
i have seen in the PI 2.1 release notes that a bug CSCum16230 which look like my problem has been resolved in PI 2.1 but i continue getting the "partail collection failure"
Would like to know if the bug is still exist or get any other help to solve this problem.
Regards,
Alon.

hello
I have this problem as well...
we've got four N5K-C5548UP. Two with a layer 3 daughter card and two without.
interestingly we see the issue just on those boxes with the l3 daughter cards N55-D160L3-V2 installed...
Any help or ideas are highly appreciated
regards
roman
Sh inventory:
OK:
device-a# sh module
Mod Ports Module-Type Model Status
1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
3 0 O2 Non L3 Daughter Card N55-DL2 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
1 5.1(3)N2(1c) 1.0 --
3 5.1(3)N2(1c) 1.0 --
NOT OK:
device-b# sh modu
Mod Ports Module-Type Model Status
1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
3 0 O2 Daughter Card with L3 ASIC N55-D160L3-V2 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
1 5.1(3)N2(1c) 1.0 --
3 5.1(3)N2(1c) 1.0 --

Similar Messages

Prime Infrastructure 2.1 ASA5580- Security Context Partial Collection Failure

I am attempting to add my ASAs into prime but get stuck almost instantly after adding the new device. Prime is able to get the device name and Device type (Cisco ASA-5580 Adaptive Security Appliance Security Context) Admin status shows up as Managed but Inventory Collection Status shows up as "Partial Collection Failure" For more detail it says "feature_image_firewall Unexpected error. See the log file inventory.log for details."
The only failure in inventory.log I could find was
[2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [inventory] [ERROR] - 192.168.0.19 For device id: 2848866 Feature = feature_image_firewall and Procedure = ImageFireWal failed in time 45 with the following error and continuing with other features: com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
[2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [ice] [ERROR] - com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
As far as the ASA config goes:
snmp-server enable
snmp-server host management 192.168.10.27 community c!$c0PR!me version 2c
logging enable
logging history 7
snmp-server enable traps
The above config works on our ASA5520s except I still haven't set up the traps right because there isn't any useful information on those devices so I am not sure what I need to change?

My ASA is using DH 1.
For 9.2(1) I read this in the release notes.
Note The ASA 5510, ASA 5520, ASA 5540, ASA 5550, and ASA 5580 are not supported in this release or later. ASA Version 9.1 was the final release for these models.

Prime Infrastructure 2.0: Inventory Collection - Partial Collection Failure on 2 of 4 VSS WS-C6509-E

Hello,
I've got a strange behaviour regarding the inventory collection for 2 of 4 virtual switching systems.
That means the inventory collection for two VSS is succesfull (inventory collections status = Completed) for the other two systems it is not, see attachments.
The device credentials like SNMP-RW, SSH acces are OK. I've already tried to increase SNMP timout and retries as well as telnet/ssh timout without success
All 4 systems are identical regarding hardware model and software vesion.
HW: WS-C6509-E
SW: 12.2(33)SXJ3
Any ideas or suggestions?
Best regards,
Bastian

TAC and I found a bug, CSCum05301.
May be that is also helpfull for others.
https://tools.cisco.com/bugsearch/bug/CSCum05301/
Symptom:
Inventory collection will fail if following keywords are used as part on description command on the interface config level of IOS device: 1Gbps, 10Mbps etc.
Following error message is visible on the DWC:
Inventory Collection Status: Partial Collection Failure
Collection Status Failed feature(s)
Unable to configure DSL, Serial, POS, Ethernet, Loopback, Virtual-Interface, Tunnel, Vlan, Switchport and Service Module interfaces on ISR, ASR and Switches.
Conditions:
Speed keywords like 1Gbps, 10Mbps etc. available as part of descrption command in IOS interface level.
For example:
interface FastEthernet0/3
description 10Mbps
Workaround:
Use a space character between number and unit keyword, like 1 Gbps.

LMS User Tracking for NEXUS 5548UP

Dear,
A while ago I received a ticket from one of our customers because User Tracking was not working for NEXUS 5548UP on LMS 3.2. I opened a TAC case for this but this was normal since it is a Datacenter switch. Now the customer came back on this because they really want to see which server is connected to which switch port. I understood from the TAC engineer this is not on the roadmap to integrate in LMS 4.x. They want to know if there exists another product (they thought about DCNM) and wanted to know how this integrates or works together with LMS...
Kind regards,
Sven Laureyssens

My latest understanding of User Tracking and Nexus 5K series is that it is not supported due to a limitation of the MIB support in the NX-OS.
The current DCNM (release 5.2) is distinct from the LMS and Cisco Prime umbrella but that wil be changing a bit moving forwad as DCNM is enhanced and rolled into the Cisco Prime family. Last I heard there should be some information coming out of Cisco Live this week and a new release will have some additional functionality and better integration. Still, I doubt we'll see UT for the 5K due to the NX-OS limitation.
One way to do what you're asking apart from use of any of the Cisco products is to enable LLDP on your Nexus and servers. That will at least give you the ability to pull the information from the NX-OS command line ("show lldp neighbor")

Cisco Prime 2.1- Partial collection failure

Dear Experts,
We are seeing many devices (around 1000+ devices) showing as "partial collection failure". We found this coz of not updated Telnet/SSH Cli username and password. So instead of editing each and every device, is there any way to select all devices and update cli credentials in one shot..?
If someone helps me this option, it will be so helpful.

Hi ,
Other way is to export all the devices , Edit it and then Import it.
Operate >device workcenter > EXPORT device \ BULK IMPORT
Thanks-
Afroz
****Ratings Encourages Contributors ****

Prime Infrastructure 2.0 Collection Failure for WLC 5508

Hi,
We have installed prime infrastructure 2.0 as a VM.
I added 2 WLCs (AIR-CT5508) in the device work center.
Both the WLCs are showing as "Managed" but under the collection status it says "Collection Failure".
When I hover over the message it reads:
Other Error: Wireless Controller added successfully but some tables had their records dropped as their key fields failed validation"
Any ideas?
Thanks
Satyaki

Hi Satyaki,
Try to reboot the WLC ,if possible and then check the status of the issue.
Regards-
Afroz
**Ratings Encourages Contributors ****

Lms 3.1 Device Collection Failure for Cat 6506-E

Unable to pull an updated device collection for a Cat6506-E running 12.2(33)SXI3. Was able to pull one when the device was running 12.2(33)SXH3, but not now. Anyone aware of a bug with the 12.2(33)SXI3 code? All other devices function correctly so I'm guessing an IOS bug, although I got tired of searching for it. Thanks in advance, Ernie

I've just upgraded to LMS 3.2, and LMS still can't inventory my two 6506-E.
I've run an "SNMP Walk" against one device, and it seems to work : here's the first few lines of it :
The following is a SNMP walk of device 10.x.x.x starting from
SNMP Walk Output
RFC1213-MIB::sysDescr.0 = STRING: "Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-VM), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 01-Sep-09 22:55 by prod_re"
RFC1213-MIB::sysObjectID.0 = OID: CISCO-PRODUCTS-MIB::cat6506
EXPRESSION-MIB::sysUpTimeInstance = Timeticks: (803850159) 93 days, 0:55:01.59
And I checked the IC_Server.log... this time it mentions SNMP timeout... I tried bumping the timeout to 20 seconds with 2 retries in Campus Manager.
I've attached my IC_Server.log excerpt.
Thanks for the help!
Alex.

Nexus 5548UP airflow

is it possible to change the airflow of the Nexus 5548UP in the field by replacing fan and power supply or must the correct airflow been ordered.

I just completed the change of airflow direction for Nexus 5548UP while the switch is still online and running. It is possible to swap fan and power modules without shutting down the switch. There are few catches that you need to pay attentions when you want to change the airflow directions:
To swap two fans and two power modules on Nexus 5548UP while it's running:
1) make sure you have the latest IOS or at least 6.0+, I have system: version 6.0(2)N2(1). Also, please don't forget to save running config just in case if the switch will be shutdown.
2) make sure you have all your new fans and power modules unpacked and ready to be installed
3) connect to the switch console port to monitor the logs and status
4) Pay attention to the switch console, it will give out warnings about fan failure (but switch will continue to run).
5) Important: The first new fan that you just replaced (with opposite airflow direction), the switch will detect the the incorrect airflow, and begin to give out warnings with countdown timer. You have only less than 60 seconds to complete the rest of swapping before the switch will shutdown. Not only you need to swap out each module quickly, but need to pay attention to each new module wait for it online before replacing the next module.
6) To start the process, insert in the first new fan with opposite airflow direction, take about few seconds and wait for spinning up [green light]. The switch console will display: "incorrect airflow detected, the switch will shutdown in 60 seconds.....". Just move onto next step...
7) replace the second fan, wait few seconds for new fan to spin up [green light].
8) replace the first power module
9) Important: make sure the first new power module is online [green light], then you can proceed and replace the second power module.
10) Completed! you may check "show inventory" to see if all new fans and power modules are online and shown. The switch was up and running the whole time.
Please give rating if it helps you! Thanks!

Inventory Collection Failure Following Upgrade to 3.2

We have 90 Cisco VPN 3002 Hardware clients deployed that we manage using Ciscoworks. Before our recent upgrade from 3.1 to 3.2 all VPN 3002 devices previously inventoried and fetched configs successfully.
Following upgrade this week we are seeing Inventory Collection failures for some (not all) of the VPN 3002 devices.
Not sure if upgrade from 3.1 to 3.2 installs a new device package for this device, but checked following upgrade and there are no Software, Device or Package updates on CCO that we need to install.
I have attached output from IC_Server.log for one of the failed VPN 3002 devices and it looks like the Inventory Collection failure is SNMP related (see attached).
Any idea if we need to upgrade code on the VPN 3002 devices? I tried deleting device from Ciscoworks and readding without success and Config Fetch is working on readded device.

There appears to be a problem getting the ifTable from these devices. It would be helpful to see a sniffer trace filtering on SNMP traffic to one failing device, then on one successful 3002 when performing inventory collection to see if there are any obvious problems. The device is replying with a noSuchName error, but it's not obvious exactly which object is causing the problem.
The other error here is related to the following Altiga objects:
alSepModuleStatsType
alSepModuleStatsState
alSepModuleStatsDspCodeVersion
Again, a noSuchName error is coming from the device.
There were no code changes in the 3.2 device package for VPN3000 devices, so something must be going on with these devices.

Cisco Prime Infrastructure 2.2: Catalyst 2960X-24TS-LL Switch Collection Failure

Hello,
I've Upgraded Prime Infrastructure to Version 2.2.0.0.158. Now our Catalyst 2960X-24TS-LL switches show an error message, when they are added to the inventory. The error is as follows:
Partial Collection Failure; Collection Status : Failed feature(s).
The 2960X-24TS-LL is listed under the supported devices list and other switches (e.g. WS-C2960X-48FPS-L) got inventorized without any problems.
Did anybody see this issue and can tell me how to solve it.
- Benjamin

- Getting that one too, since running 2.2 (Failed Features) ; suggest opening a TAC case.
M.

Do we have a built-in option for web based tool in Nexus 5548UP switches for management purpose?

I have purchased Nexus 5548UP switch, i want to know if we have a built-in option for web based tool to manage and configur it just as ASA have ASDM. If there is no such options then what are the options available that can be freely available and can be used to get performance monitoring done.
Message was edited by: Praveen Varun

DCNM (Data Center Network Manager) runs on a server (Windows, RHEL or Solaris) and can be used to manage Nexus devices. It's free for Nexus 1K through 5K devices (paid license required for Nexus 7K management).
http://www.cisco.com/en/US/products/ps9369/index.html
There is not a "built-in" management product like ASDM for ASA.

Nexus 5548UP for SAN Switch

We have purchased a Nexus 5548UP switch for our SAN environment. I've only configured it for jumbo frames and currently doing testing on the performance, as some say use jumbo frames while others say do not. My question is, and I know this is a loaded question but how do you guys go about configuring your SAN switches? What exactly are you configuring on it? Such as for performance tuning or the like. The reason I ask, is we have the switch and it's pretty much working, but I'd like to learn more about it and how to tune it and fully take advantage of the switch.

That is correct, between two Dell Optiplex workstations. We also tested between the server that will go into prod and an Optiplex, but once again the Optiplex could be the limiting factor. You think that could be it? Here's my config, so you know how it's setup right now.
version 5.2(1)N1(7)
hostname N5K
feature telnet
feature lldp
feature vtp
username admin password 5 $1$oZ1234567898765432123456/ role network-admin
banner motd #Nexus 5000 Switch
ip domain-lookup
policy-map type network-qos jumbo
class type network-qos class-default
mtu 9216
multicast-optimize
system qos
service-policy type network-qos jumbo
snmp-server user admin network-admin auth md5 0x422842c9d320064123456789fc703d20
priv d3264f23456789000c703d20 localizedkey
vrf context management
port-profile default max-ports 512
interface Ethernet1/1
flowcontrol receive on
flowcontrol send on
interface Ethernet1/2
interface Ethernet1/3
interface Ethernet1/4
interface Ethernet1/5
flowcontrol receive on
flowcontrol send on
interface Ethernet1/6
interface Ethernet1/7
interface Ethernet1/8
interface Ethernet1/9
flowcontrol receive on
flowcontrol send on
interface Ethernet1/10
interface Ethernet1/11
interface Ethernet1/12
interface Ethernet1/13
flowcontrol receive on
flowcontrol send on
interface Ethernet1/14
interface Ethernet1/15
interface Ethernet1/16
interface Ethernet1/17
interface Ethernet1/18
interface Ethernet1/19
interface Ethernet1/20
interface Ethernet1/21
interface Ethernet1/22
interface Ethernet1/23
interface Ethernet1/24
interface Ethernet1/25
interface Ethernet1/26
interface Ethernet1/27
interface Ethernet1/28
interface Ethernet1/29
interface Ethernet1/30
interface Ethernet1/31
interface Ethernet1/32
interface mgmt0
ip address 11.11.11.11/24
line console
exec-timeout 720
line vty
boot kickstart bootflash:/n5000-uk9-kickstart.5.2.1.N1.7.bin
boot system bootflash:/n5000-uk9.5.2.1.N1.7.bin

Import Error (Partial Set failure with RC error code = 0x84020020 for rec

Hi,
While importing the data through xls file , i am getting the error message "Partial Set failure with RC error code = <0x84020020> for record number
0 through 212" and no record get created in Data manager.
Although i mapped all values , still it giving me an error message.
I tried to Import other data and it was all working fine.
Please guide
Regards
Sandeep Kumar

HI,
I checked the exl file and found that in the first column and first data was in text format ('0001)but later on when i change the record and moved it to the last record , it worked fine. I was able to load all records including ('0001)
I don't know wht the logic behind this:
if my first record was ('0001), system was giving me the error and not allowing me to load the data. But when i moved the record as the last record it not only allow me to load the records but allow ('0001) also.
If anyone have any clue , plz let me know.
Regards
Sandeep

Nexus 5548UP L3 card swap out for L2 cards

Hi everyone,
I have two Nexus 5548UPs and I am going to swap out the L3 cards and put in L2 cards.
I can't seem to get a straight answer out of TAC so I thought I'd try here.
How will this affect the current configuration (apart of course from removing the L3 capability)?
Will swapping the cards clear the config?
Will swapping the cards clear the licenses?
It's a very simple config so that doesn't worry me that much .. but if it will clear the licenses installed than I need to take action on that.
Thanks,
BR

no, no secret aukhadiev
I made a mistake without realising and the interface e1/3 was showing "Interface Ethernet1/3 is down (Inactive)". After spending sometime trying to figure out what was wrong with that interface or switch, it turned out to be that i forgot to add the vlan 40. Now the config looks like this:
N5K-C5548UP Switch
feature interface-vlan
feature lacp
feature dhcp
feature lldp
vrf context management
ip route 0.0.0.0/0 172.16.0.1
vlan 1
vlan 40
vlan 100
service dhcp
ip dhcp relay
interface Vlan1
no shutdown
interface Vlan40
description ** Server VLAN **
no shutdown
ip address 10.144.40.3/25
ip dhcp relay address 10.144.40.39
ip dhcp relay address 10.144.40.40
interface port-channel1
description ** Trunk Link to Switch A g1/0/23-24 **
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
interface Ethernet1/1
description ** Trunk Link to Switch A g1/0/23**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,12
speed 1000
channel-group 1 mode active
interface Ethernet1/2
description ** Trunk Link to Switch A g1/0/24**
switchport mode trunk
switchport trunk allowed vlan 1,30,40,100-101,122
speed 1000
channel-group 1 mode active
interface Ethernet1/3
description **Connected to server B**
switchport access vlan 40
speed 1000
interface mgmt0
description connection to Switch A g2/0/20
no ip redirects
ip address 172.16.0.2/25
Thank you,
JN

Connecting many Brocade switches to Nexus 5548UP

Hello,
I have a SAN network composed of few separate PODs. Each POD is divided into SAN-A and SAN-B. Most of those PODs are Brocade switches (FOS 6.1). There are also few Nexus 5520s. Now, we have built new core infrastructure with Nexus 5548UPs and many MDS 9148s. We would like to move all servers and sotrage from old Brocades to the new SAN. As we cannot move all devices at the same time, all segments must be connected to the core for some time. Each POD has different zoning. Some zonings on Brocade switches are based on PWWN, some on Domain ID and Port ID. In my opinion, the only way of successfuly connecting all PODs together is to merge zones manualy (in excel, etc). and paste them on all switches. However, maybe there is some other way of merging all zones? What if I leave Nexus 5548UP in native mode (so zones from Brocade will not get merged), and only implement that manually merged zoneset on Nexus 5548UP? Will the ISL links get isolated due to zoning merge failure? Or they will maintain operational state even if zones are different on each POD? I do not have any lab boxes, so I cannot test it. Any advidse will be appreciated.
Best regards,
Krzyszof

well since you can not cluster the 45K as a virtual switch ( Cisco with new sup will start support VSS in the 4500 try to check which sup exactly and if you can upgrade as this will make a significant improvement to your design )
anyway the only method that you can use currently is the traditional way which is depending on STP ( use rapid-PVST)
from each N5K use one separate link to each 45K and STP will put on of the links in blocking mode
however you might do some STP and vlan design for load sharing where you can send vlan x over link1 and vlan y over link b to the 45K using STP cost
HTH

Partial collection Failure for nexus 5548UP in PI 2.1

Similar Messages

Maybe you are looking for