Partial recovery failure

I am repairing a hp laptop DV7 for a friend, I have the recovery dvd's and drivers dvd
but all I get is a message that the recovery has a partial failure. I can never
get the system restored to factory settings.
I loaded windows 7 64bit pro easily, but I could not get the drivers
loaded because the nic card driver could not be loaded.
What is wrong with this proceedure I thought it was supposed to be
simple? change the boot order to make the dvd drive first
and install the dvds in order.. What is missing from this picture in getting
this DV7 laptop working?
Thanks.

Hi:
This is the link to the support and driver page for the notebook:
http://h10025.www1.hp.com/ewfrf/wc/product?product=5189529&lc=en&cc=us&dlc=en&task=&lang=en&cc=us
Like I said, I need the hardware ID's. For example, note the list of wireless network adapters.
You need to know the hardware ID's in order to install the right driver.
Looking at the specs for the notebook, there are some drivers you need that aren't listed on the page.
For example...Chipset which you need to install first and reboot before installing any other driver.
First download is what you need.
http://support.amd.com/us/gpudownload/windows/Pages/raid_windows.aspx
Second is video. Install and reboot.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-103171-1&cc=us&dlc=en&lc=en...=
I do not know what audio your model has. There could be one of two audio chips installed Conexant or IDT.
Again, that is why I need the hardware ID's so I can post the drivers you need.
Wired Network:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-102406-1&cc=us&dlc=en&lc=en...=
How you want to make a folder for these drivers and run them is up to you.
But we can get this done for your friend.
Paul

Similar Messages

How to design a grid to withstand a partial network failure

Hi,
We are evaluating Coherence for a mission-critical system where we want to test partial network failure scenario. We want to run 4 physical hosts, 8 JVMs with 2 JVM on each host. The evaluation criteria is to connect 2 machines on either side of a router, kill one side during a load test, thereby disconnecting the 2 machines and run with the remaining two. In order to have a fail-safe behavior in this scenario, I guess we must ascertain that the back-ups for the objects on one side of a router are always made on the other side. Can Coherence detect such a network set up and store backups accordingly? Or is there a way to configure this by overriding the default behavior?
Pls advise
Thanks,
Sairam

Hi Sairam
If you use scenario 1) then your test will work. As this scenario only has two machines then the primary node for a piece of data will be on one machine and Coherence will make sure the backup is on the other machine. If you then break the link between the machines or lose a machine you will not have lost data.
If however you have more than 2 machines then you break the link between them you have what is known as a split-brain - which means you have effectively split your cluster in two. Both sides only know they they can no longer see the other part of the cluster and assume they are must be the remaining working part. In this case though you will have lost data from the cluster as some of the backups for each part of the cluster will be on the other part. There is nothing you can do about this, you cannot control which machines backups are allocated to.
Increasing the backup count to 3 does not give you any more reliance than having a backup count of 2. As far as I know Coherence only guarantees that the placement of the first backup is on another machine.
I am not quite sure what you are trying to test as a Coherence cluster cannot automatically survive a network failure that splits the cluster. There are things in 3.6 that you might be able to do with Quorums to mitigate the damage while you recover and there are things you can do to make recovery easier - but you will have to recover lost data.
JK

Prime Infrastructure 2.0: Inventory Collection - Partial Collection Failure on 2 of 4 VSS WS-C6509-E

Hello,
I've got a strange behaviour regarding the inventory collection for 2 of 4 virtual switching systems.
That means the inventory collection for two VSS is succesfull (inventory collections status = Completed) for the other two systems it is not, see attachments.
The device credentials like SNMP-RW, SSH acces are OK. I've already tried to increase SNMP timout and retries as well as telnet/ssh timout without success
All 4 systems are identical regarding hardware model and software vesion.
HW: WS-C6509-E
SW: 12.2(33)SXJ3
Any ideas or suggestions?
Best regards,
Bastian

TAC and I found a bug, CSCum05301.
May be that is also helpfull for others.
https://tools.cisco.com/bugsearch/bug/CSCum05301/
Symptom:
Inventory collection will fail if following keywords are used as part on description command on the interface config level of IOS device: 1Gbps, 10Mbps etc.
Following error message is visible on the DWC:
Inventory Collection Status: Partial Collection Failure
Collection Status Failed feature(s)
Unable to configure DSL, Serial, POS, Ethernet, Loopback, Virtual-Interface, Tunnel, Vlan, Switchport and Service Module interfaces on ISR, ASR and Switches.
Conditions:
Speed keywords like 1Gbps, 10Mbps etc. available as part of descrption command in IOS interface level.
For example:
interface FastEthernet0/3
description 10Mbps
Workaround:
Use a space character between number and unit keyword, like 1 Gbps.

Prime Infrastructure 2.1 ASA5580- Security Context Partial Collection Failure

I am attempting to add my ASAs into prime but get stuck almost instantly after adding the new device. Prime is able to get the device name and Device type (Cisco ASA-5580 Adaptive Security Appliance Security Context) Admin status shows up as Managed but Inventory Collection Status shows up as "Partial Collection Failure" For more detail it says "feature_image_firewall Unexpected error. See the log file inventory.log for details."
The only failure in inventory.log I could find was
[2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [inventory] [ERROR] - 192.168.0.19 For device id: 2848866 Feature = feature_image_firewall and Procedure = ImageFireWal failed in time 45 with the following error and continuing with other features: com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
[2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [ice] [ERROR] - com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
As far as the ASA config goes:
snmp-server enable
snmp-server host management 192.168.10.27 community c!$c0PR!me version 2c
logging enable
logging history 7
snmp-server enable traps
The above config works on our ASA5520s except I still haven't set up the traps right because there isn't any useful information on those devices so I am not sure what I need to change?

My ASA is using DH 1.
For 9.2(1) I read this in the release notes.
Note The ASA 5510, ASA 5520, ASA 5540, ASA 5550, and ASA 5580 are not supported in this release or later. ASA Version 9.1 was the final release for these models.

Partial collection Failure for nexus 5548UP in PI 2.1

Hi there,
I get "Partial Collection Failure" in the inventory collection status in Prime Infrastructure for all my Nexus 5548UP (8 devices).
i have seen in the PI 2.1 release notes that a bug CSCum16230 which look like my problem has been resolved in PI 2.1 but i continue getting the "partail collection failure"
Would like to know if the bug is still exist or get any other help to solve this problem.
Regards,
Alon.

hello
I have this problem as well...
we've got four N5K-C5548UP. Two with a layer 3 daughter card and two without.
interestingly we see the issue just on those boxes with the l3 daughter cards N55-D160L3-V2 installed...
Any help or ideas are highly appreciated
regards
roman
Sh inventory:
OK:
device-a# sh module
Mod Ports Module-Type Model Status
1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
3 0 O2 Non L3 Daughter Card N55-DL2 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
1 5.1(3)N2(1c) 1.0 --
3 5.1(3)N2(1c) 1.0 --
NOT OK:
device-b# sh modu
Mod Ports Module-Type Model Status
1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
3 0 O2 Daughter Card with L3 ASIC N55-D160L3-V2 ok
Mod Sw Hw World-Wide-Name(s) (WWN)
1 5.1(3)N2(1c) 1.0 --
3 5.1(3)N2(1c) 1.0 --

Partial recovery in RMAN 8i

Hi,
I'm looking for an example of partial recovery (a table only, or a tablespace or some rows in a table) in RMAN 8i.
I deleted some rows from a table and I recovered its tablespace I did not find the rows.
Many thanks.

What you actually performed was a complete recovery of a tablespace. You must perform a TSPITR (TableSpace Point In Time Recovery):
http://www.csee.umbc.edu/help/oracle8/server.815/a67773/rmantspi.htm

Cisco Prime 2.1- Partial collection failure

Dear Experts,
We are seeing many devices (around 1000+ devices) showing as "partial collection failure". We found this coz of not updated Telnet/SSH Cli username and password. So instead of editing each and every device, is there any way to select all devices and update cli credentials in one shot..?
If someone helps me this option, it will be so helpful.

Hi ,
Other way is to export all the devices , Edit it and then Import it.
Operate >device workcenter > EXPORT device \ BULK IMPORT
Thanks-
Afroz
****Ratings Encourages Contributors ****

Import Error (Partial Set failure with RC error code = 0x84020020 for rec

Hi,
While importing the data through xls file , i am getting the error message "Partial Set failure with RC error code = <0x84020020> for record number
0 through 212" and no record get created in Data manager.
Although i mapped all values , still it giving me an error message.
I tried to Import other data and it was all working fine.
Please guide
Regards
Sandeep Kumar

HI,
I checked the exl file and found that in the first column and first data was in text format ('0001)but later on when i change the record and moved it to the last record , it worked fine. I was able to load all records including ('0001)
I don't know wht the logic behind this:
if my first record was ('0001), system was giving me the error and not allowing me to load the data. But when i moved the record as the last record it not only allow me to load the records but allow ('0001) also.
If anyone have any clue , plz let me know.
Regards
Sandeep

Recovery Failure in Oracle enterprise manager

Hi ,
When i tried to recover the whole database by selecting "Recover to the current time or a previous point-in-time" in Perform recovery area.
It came up with the error message as shown below.
ERROR :::::
startup mount
shutdown immediate
shutdown immediate
SQL*Plus: Release 11.2.0.1.0 Production on Tue Jun 1 14:45:44 2010
Copyright (c) 1982, 2009, Oracle. All rights reserved.
SQL> SQL> Connected.
SQL> SQL> SQL> Database closed.
Database dismounted.
ORACLE instance shut down.
SQL> SQL> Disconnected from Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
With the Partitioning option
startup mount
SQL*Plus: Release 11.2.0.1.0 Production on Tue Jun 1 14:46:45 2010
Copyright (c) 1982, 2009, Oracle. All rights reserved.
SQL> SQL> Connected to an idle instance.
SQL> SQL> ORACLE instance started.
Total System Global Area 2137886720 bytes
Fixed Size 2215064 bytes
Variable Size 1677722472 bytes
Database Buffers 452984832 bytes
Redo Buffers 4964352 bytes
Database mounted.
SQL> Disconnected from Oracle Database 11g Enterprise Edition Release 11.2.0.1.0 - 64bit Production
With the Partitioning option
Recovery Manager: Release 11.2.0.1.0 - Production on Tue Jun 1 14:46:50 2010
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
RMAN>
connected to target database: SPPADEV (DBID=1558297262, not open)
using target database control file instead of recovery catalog
RMAN>
echo set on
RMAN> run {
2> restore database until time "to_date('2010-05-20 20:00:00', 'YYYY-MM-DD HH24:MI:SS')";
3> recover database until time "to_date('2010-05-20 20:00:00', 'YYYY-MM-DD HH24:MI:SS')";
4> }
Starting restore at 01-JUN-10
allocated channel: ORA_DISK_1
channel ORA_DISK_1: SID=452 device type=DISK
allocated channel: ORA_DISK_2
channel ORA_DISK_2: SID=3 device type=DISK
allocated channel: ORA_DISK_3
channel ORA_DISK_3: SID=32 device type=DISK
allocated channel: ORA_DISK_4
channel ORA_DISK_4: SID=62 device type=DISK
creating datafile file number=1 name=/u02/oradata/SPPADEV/system01.dbf
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of restore command at 06/01/2010 14:46:52
ORA-01180: can not create datafile 1
ORA-01110: data file 1: '/u02/oradata/SPPADEV/system01.dbf'
RMAN> exit;
Recovery Manager complete.
Recovery Manager: Release 11.2.0.1.0 - Production on Tue Jun 1 14:46:52 2010
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
RMAN>
connected to target database: SPPADEV (DBID=1558297262, not open)
using target database control file instead of recovery catalog
RMAN>
echo set on
RMAN> alter database open resetlogs;
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of alter db command at 06/01/2010 14:46:53
ORA-01139: RESETLOGS option only valid after an incomplete database recovery
RMAN> exit;
Recovery Manager complete.
Recovery Manager: Release 11.2.0.1.0 - Production on Tue Jun 1 14:46:53 2010
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
RMAN>
connected to target database: SPPADEV (DBID=1558297262, not open)
using target database control file instead of recovery catalog
RMAN>
echo set on
RMAN> alter database open resetlogs;
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of alter db command at 06/01/2010 14:46:53
ORA-01139: RESETLOGS option only valid after an incomplete database recovery
RMAN> exit;
Recovery Manager complete.
It will be very much grateful if some one can help me with this issue.
Thanks,
Hary

I see the error: ORA-01180: can not create datafile 1
ORA-01110: data file 1: '/u02/oradata/SPPADEV/system01.dbf'
Does oracle have the rights to create that file there?

Partial Recovery - Skip UNDO Tablespace

Hi,
I was performing a partial database recovery using skip tablespace option using RMAN. I was wondering if I can skip undo tablespace.
I was not able to conclude whether I can do that? If not, why?
As per my understanding,
1. Datafiles are restored - If they have any uncommited data, then archive logs which will be applied for media recovery, will have the undo data to perform those roll backward.
2. While performing media reccovery using archive logs, it will generate it's own undo data.
Why do we need the stale undo data (generated till datafiles restoration point)?
Thanks,
Janak Agrawal

Soli,
Thread that you have specified, talks about datafiles which does not have any uncommitted data (As the database was normally shutdown). In this case, we can drop and recreate the undo tablespace.
But I am talking about a past point-in-time recovery using RMAN, where the datafiles which will be restored may have the uncommitted data. To rollback these uncommited trnasactions, will we have data in next archivelogs, which will be used for media recovery or the data (needed to rollback) will have only in undo tablespace. Let me give you an example.
At 9 am I want to restore the datbase till 8.15 AM. Full backup is available till 8 AM and then from 8 to 8:15 arvhive logs are available. While doing recovery, datafiles will be restored till 8 AM. If at 8 AM there is some uncommitted data in datafiles, will it require data from undo tablespace to rollback or first archive log after 8 AM w'd take care of roll back? If archive logs can take care of rollback, why can't I skip the undo tablespace while doing recovery?
Santosh,
As you mentioned, UNDO data will require for read-consistency. But the same data will be available in archive logs (which will require after datafiles restore) which can generate their own UNDO data.
Please clarify. I am sorry if I am missing anything here.
Thanks,
Janak Agrawal

Presario recovery failure

Compaq Presario CQ60-212US, Vista OS, 64 Bit. I created a recovery DVD and then ran recovery. After formatting hard drive it attempted to recover files to the original state but failed, giving error code 1002. The same result using my recovery DVD. I ran the hard drive tests - all normal. I downloaded and tried to install the Vista repair file (ISO file) but it would not respond. I also get a message that says BOOTMGR missing. Please advise how I can successfully run a recovery. Thanks.

Did you test your memory?
http://h30434.www3.hp.com/t5/Notebook-Lockups-Freezes-Hangs/How-to-test-RAM-and-HDD-Hard-Drive/td-p/...
Here is one specific to that error code, but only happens if you backup your files at the start of recovery, I am not sure if this error could happen if you have an external drive connected during recovery but did Not do a file backup.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00881405&cc=us&dlc=en&lc=en#N406
Others that may apply
Read this also, recovery can be interrupted unintentionally by the user and cause failure
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01612373&cc=us&lc=en&dlc=en
The wireless must be enabled during recovery also
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01497847&cc=us&lc=en&dlc=en

Server 2012 R2 RDS Personal Collection -reuse VM names after a partial job failure

I am currently testing RDS on server 2012 R2, and as part of the test I have built and rebuilt multiple collections of VMs. I have noticed that when creating a new JOB to build a personal collection, sometimes I get VM build failures on one host. The build
failures are usually due to a networking issue, which I then resolve, but when I go to add/create the VMs that failed, the name of the VMs increment from the last VM, and they don't re-use the failed names. I want to be able to reuse/build the VMs that
failed.
eg.
VM-01, VM-02, VM-03 - On HOST-01 all work
VM-04, VM-05, VM-06 - On HOST-02 fail
VM-07, VM-08, VM-09 - On HOST-03 all work
So on this example, when I re-run the job to build the missing/failed VMs, it would build VM-10, VM-11, VM-12 on HOST-02.
Is there a way to reset, or reuse the failed VM names, in the example above that would be VM-04, VM-05, and VM-06?
Thanks

Hi,
Thank you for posting in Windows Server Forum.
For a try you can use powershell command for RD VDI infrastructure.
New-RDVirtualDesktopCollection -CollectionName "ITCamp" -PooledManaged -StorageType CentralSmbShareStorage -VirtualDesktopAllocation 5 -VirtualDesktopTemplateHostServer $VHost -VirtualDesktopTemplateName $VDITemplateVM -ConnectionBroker $RDBroker -Domain “contoso.com”
-Force -MaxUserProfileDiskSizeGB 40 -CentralStoragePath”\\fileserver1\NormalVMs” -VirtualDesktopNamePrefix "ITC" -OU “VDICampUsers” -UserProfileDiskPath \\fileserver1\NormalProfiles
More information.
Lab Ops 7 – Setting up a pooled VDI collection in Windows Server 2012 R2
http://blogs.technet.com/b/andrew/archive/2013/10/28/lab-ops-4-windows-8-1-windows-2012r2-vdi.aspx
Also check that when setting up RDS, there needs to be a Physical NIC with IP for the creation of a RDS vSwitch. If this vswitch does not exist, the creation of the MV's will fail.
Hope it helps!
Thanks.
Dharmesh Solanki

Dv4-1275mx Replaced Hard Drive Windows Vista System Recovery Failure

I have a HP dv4 1275mx laptop and I just replaced the hard drive. I got the Vista 64-bit hp system recovery discs from HP but the recovery has failed 4 times. The hard drive is brand new and has more space than the old one. It's a Western Digital 640 gb scorpio blue sata 5400 rpm. Windows will not complete the download.
On the original hard drive, I upgraded to Windows 7.
Error message:
[17:18:51.36] chkerrBB.cmd Detect some error during PININST_BBV.
[17:18:51.37] chkerrBB.cmd check c:\system.sav\logs\BurnBootWarn.log

Try the "Solution" offered here:
http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and/Recovery-Manager-Problem-Recovery-fails/...
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Recovery Failure of hp Pavillion dv8 after hard drive replaced.

I have an hp Pavillion dv8 Product VF836AV. Model dv8t-1100 between one and two years old and out of warranty.
The 320 GB Seagate hard drive failed.
I had a local shop install a new hard drive.
I attempted to use an HP DV8-1001XX W764 Dual OS Recovery Kit [2DVD's Super Recovery 588725-001 with Supplemental CD] to get the computer running again.
The Kit envelope says "Please read the instructions before beginning" -- What instructions? All the package said was 'Start with "Changing the Boot Order of the BIOS" '. How?
I simply turned the machine on and loaded the DVD's one by one per the prompts on the screen.
The process seemed to go OK, but at the end it said the recovery failed.
What do I do now?
Thanks for any assistance. ///

Hi,
Assuming you're trying to reinstall Windows 7, there is an easy work around if you have ( or can borrow ) a retail Windows 7 installation disc that is exactly the same version as your OEM installation - ie if your notebook came with Windows 7 Home Premium 64bit this is the exact retail version you would need.
Use the disc to perform the installation, enter the Windows activation key found on the underside of your notebook when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
Any additional drivers you may need can be found Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

HP G62 Windows Startup error recovery Failure

Notebook:
HP G62 - 228CL
Running Windows 7 64-bit
Hello everyone, I need a bit of help.
My computer will boot windows 7. When I start it up, it tries to boot up. I then get a Windows failed to boot message on the windows error recovery screen and asks me if I would like to use Windows Startup Repair Tool to fix the Problem. But the tool never starts up. It just leads to a windows background and does nothing. I have also tried using f11 System recovery but it does nothing.

Hi,
Firstly, regarding your existing files.
One possible way to try and retrieve your files from a non-booting drive is to follow the process detailed in the link below. The Ubuntu operating system CD you create can run from the CD alone ( ie it doesn't have to install on the Hard Drive ) and I've often found it to be successful in retrieving data even from a failing Hard Drive. When you've created the CD, follow the instructions and see if you can back up your existing files.
http://www.howtogeek.com/howto/windows-vista/use-ubuntu-live-cd-to-backup-files-from-your-dead-windo...
Secondly, regarding the replacement of the Hard Drive.
The drive on the link below is an example of one that would be fine for your notebook.
500Gb Hard Drive
The procedure to replace the Hard Drive starts on Page 52 of your Maintenance & Service Guide.
Once done, simply use your Recovery DVDs to reinstall the Operating System on the new drive - the procedure is described in the HP document Here.
If you don't have your Recovery Discs, you can order a replacement set using the link below.
Order HP Recovery Discs.
If you have any problem with this link, order them directly from HP.
If you live in the US, contact HP Here.
If you are in another part of the world, start Here.
Best regards and happy holidays,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Partial recovery failure

Similar Messages

Maybe you are looking for