Partial sync failure

Certain Music tracks fail to sync. They show a partial download symbols and there it gets stuck.

I have the same issue with the nightly and aurora versions. Firefox 11 works fine.

Similar Messages

  • Outlook to iPhone sync failure – Sync suddenly stopped working for calendar events but continued for contacts and notes.   Finally Fixed!!!  SUPPORT TEAM – PLEASE SEE THIS – Complete explanation of cause and correction steps.

    The issue:  Outlook to iPhone sync failure – Sync suddenly stopped working for calendar events but continued for contacts and notes.   Finally Fixed!!! 
    SUPPORT TEAM – PLEASE SEE THIS – Complete explanation of cause and correction steps.
    The cause:  It is now clear what caused this problem.  For years I had several “all-day” events in my Outlook calendar (birthdays, anniversaries, etc.).  In May 2012 I decided to make some of them one hour  events so I could add alerts to remind me of the event.  I did this by dragging them in Outlook to the time I wanted and expanding them to the time slot desired and then adding the alarm.
    The symptom:  Syncing stopped working for the calendar but continued working for contacts and notes.  I didn’t realize sync was failing until months later when I missed two very important phone calls, so when I noticed it the cause was not obvious. 
    The failed attempts:  I’m head of a software firm and my calendar sync is a crucial to my business life so I took this on with a vengeance.  From a quick look at events in Outlook and the iPhone I could see that the problem started in May 2012.  Events before May were in both Outlook and the iPhone but events after May were only one or the other.  Unfortunately I had changed several other things at the same time relating to other events so again the cause was not obvious.  MANY calls with AppleCare proved them incompetent so my internal IT guys assisted trying many things.  We tried a huge number of calendar changes and several versions of iTunes, iPhone OS and Office as well as both iPhone 4 and 5, all without success.
    The fix:  After 18 months of frustration, MANY  hundreds of $ expense and MANY hours of wasted time I saw a blog that had a calendar sync  problem and it indicated all day events were related.  I changed the display of the Outlook calendar to the list view, added columns so I could see “all day” event check marks as well as times of events,  sorted on the “all day” event column to move them to the top, and for all events that were “all day” events AND had a start and end time, I removed recurrence and then added the annual recurrence back…
    After I fixed all events that had BOTH “all day” set and had a start/end time, I tried another sync.  It synced for the first time in 18 months! 
    Problem occurred May 2012 – fixed Nov 2013

    Hi, to remove dummy '_ModGrp' entries, rather than crashing the 'Suppr' key on your keyboard, you can use this basic VBA macro (launched for instance from Excel).
    It will recursively remove all '_ModGrp...' folders
    Sub RemoveFolders_Click()
        Dim oOutlook As Outlook.Application
        Set oOutlook = New Outlook.Application
        Set objNameSpace = oOutlook.GetNamespace("MAPI")
        Call CleanFolders(objNameSpace.Folders)
    End Sub
    Sub CleanFolders(objFolders As Outlook.Folders)
        For i = objFolders.Count To 1 Step -1
            If Left(objFolders(i).Name, 7) = "_ModGrp" Then
                objFolders.Remove( i )
            Else
                If Not objFolders(i).Folders Is Nothing Then
                    Call CleanFolders(objFolders(i).Folders)
                End If
            End If
        Next i
    End Sub

  • I made the mistake of resetting my iPod to factory defaults. Now it will only partially sync to my music library. I continually get an error message saying that certain songs are not authorized for my computer. Any ideas?

    I made the mistake of resetting my iPod to factory defaults. Now it will only partially sync to my music library. I continually get an error message saying that certain songs are not authorized for my computer, although they are in the iTunes library on the computer and will play. It's these songs that won't transfer to the iPod. I have deauthorized and re-authorized the computer but no joy. Any ideas?

    Hello there DesertRat71,
    I was thinking that some of the songs in your library may have been purchased under a different apple id. You have already done the first thing I would have done by de authorizing and re authorizing. To verify this, highlight one of the songs that will not sync over and use File>Get Info. Here is the help menu link for it if you need it help://bookmark='https://help.apple.com/itunes/mac/11.0/help/index.html?localePa th=English.lproj#itns2937'
    In the Summary section there will be an Apple ID entry. If it shows something different than what you are currently using then I recommend signing into the Apple ID it shows and authorizing the computer for that one as well.
    All the best,
    Sterling

  • I have an imac with IMAP email. have managed to partially sync up my ipad in that I can receive the same emails that appear on my imac but I can't send from my ipad.  Any ideas?

    I have an imac with IMAP email. have managed to partially sync up my ipad with it in that I can receive the same emails that appear on my imac but I can't send from my ipad.  Any ideas?

    That sounds like a settings issue to me. Check with your IT depatment to make sure you have it configured properly.

  • Prime Infrastructure 2.0: Inventory Collection - Partial Collection Failure on 2 of 4 VSS WS-C6509-E

    Hello,
    I've got a strange behaviour regarding the inventory collection for 2 of 4 virtual switching systems.
    That means the inventory collection for two VSS is succesfull (inventory collections status = Completed) for the other two systems it is not, see attachments.
    The device credentials like SNMP-RW, SSH acces are OK. I've already tried to increase SNMP timout and retries as well as telnet/ssh timout without success
    All 4 systems are identical regarding hardware model and software vesion.
    HW: WS-C6509-E
    SW: 12.2(33)SXJ3
    Any ideas or suggestions?
    Best regards,
    Bastian

    TAC and I found a bug, CSCum05301.
    May be that is also helpfull for others.
    https://tools.cisco.com/bugsearch/bug/CSCum05301/
    Symptom:
    Inventory collection will fail if following keywords are used as part on description command on the interface config level of IOS device: 1Gbps, 10Mbps etc.
    Following error message is visible on the DWC:
    Inventory Collection Status: Partial Collection Failure
    Collection Status     Failed feature(s)
    Unable to configure DSL, Serial, POS, Ethernet, Loopback, Virtual-Interface, Tunnel, Vlan, Switchport and Service Module interfaces on ISR, ASR and Switches.
    Conditions:
    Speed keywords like 1Gbps, 10Mbps etc. available as part of descrption command in IOS interface level.
    For example:
    interface FastEthernet0/3
    description 10Mbps
    Workaround:
    Use a space character between number and unit keyword, like 1 Gbps.

  • How to design a grid to withstand a partial network failure

    Hi,
    We are evaluating Coherence for a mission-critical system where we want to test partial network failure scenario. We want to run 4 physical hosts, 8 JVMs with 2 JVM on each host. The evaluation criteria is to connect 2 machines on either side of a router, kill one side during a load test, thereby disconnecting the 2 machines and run with the remaining two. In order to have a fail-safe behavior in this scenario, I guess we must ascertain that the back-ups for the objects on one side of a router are always made on the other side. Can Coherence detect such a network set up and store backups accordingly? Or is there a way to configure this by overriding the default behavior?
    Pls advise
    Thanks,
    Sairam

    Hi Sairam
    If you use scenario 1) then your test will work. As this scenario only has two machines then the primary node for a piece of data will be on one machine and Coherence will make sure the backup is on the other machine. If you then break the link between the machines or lose a machine you will not have lost data.
    If however you have more than 2 machines then you break the link between them you have what is known as a split-brain - which means you have effectively split your cluster in two. Both sides only know they they can no longer see the other part of the cluster and assume they are must be the remaining working part. In this case though you will have lost data from the cluster as some of the backups for each part of the cluster will be on the other part. There is nothing you can do about this, you cannot control which machines backups are allocated to.
    Increasing the backup count to 3 does not give you any more reliance than having a backup count of 2. As far as I know Coherence only guarantees that the placement of the first backup is on another machine.
    I am not quite sure what you are trying to test as a Coherence cluster cannot automatically survive a network failure that splits the cluster. There are things in 3.6 that you might be able to do with Quorums to mitigate the damage while you recover and there are things you can do to make recovery easier - but you will have to recover lost data.
    JK

  • Prime Infrastructure 2.1 ASA5580- Security Context Partial Collection Failure

    I am attempting to add my ASAs into prime but get stuck almost instantly after adding the new device. Prime is able to get the device name and Device type (Cisco ASA-5580 Adaptive Security Appliance Security Context) Admin status shows up as Managed but Inventory Collection Status shows up as "Partial Collection Failure" For more detail it says "feature_image_firewall Unexpected error. See the log file inventory.log for details."
    The only failure in inventory.log I could find was
    [2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [inventory] [ERROR] - 192.168.0.19 For device id: 2848866 Feature = feature_image_firewall and Procedure = ImageFireWal failed in time 45 with the following error and continuing with other features: com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
    [2014-09-26 12:40:01,868] [ICE Service[ 1]Thread: 20] [ice] [ERROR] - com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
    com.cisco.nm.expression.function.FunctionException: <palError><deviceId>2848866</deviceId><code>HANDLER_ERROR</code><message>Error while trying to run handler. Action : imageFireWall, Handler : com.cisco.nm.pal.customhandler.RPLHandler. Error : Exception thrown : Constraint violation. See log for details.</message><handlerCode>ERROR_HANDLER_ERROR</handlerCode></palError>
    As far as the ASA config goes:
    snmp-server enable
    snmp-server host management 192.168.10.27 community c!$c0PR!me version 2c
    logging enable
    logging history 7
    snmp-server enable traps
    The above config works on our ASA5520s except I still haven't set up the traps right because there isn't any useful information on those devices so I am not sure what I need to change?

    My ASA is using DH 1.
    For 9.2(1) I read this in the release notes.
    Note The ASA 5510, ASA 5520, ASA 5540, ASA 5550, and ASA 5580 are not supported in this release or later. ASA Version 9.1 was the final release for these models.

  • Bonjour iTunes Wireless Sync Failure

    Looking to see if anyone has experienced any iTunes Wireless Sync issues:  Network setup as follows:
    2504 Wireless Controller running 7.6.100.10 and three 1602 AP's set for LOCAL Mode running CAPWAP, and running a Guest WLAN and a User WLAN.
    We use a wide variety of Mac products (iPad, Mac Mini, AppleTV, iPhones, MacBooks), and are now experiencing iTunes Wireless sync failures.  I have mDNS enabled, mDNS is added to the WLAN's and the interfaces, multicast is tuned on, IGMP snooping enabled, multicast is enabled on the wired infrastructure....the weird thing is all the other Bonjour features are working.  We can push desktops to the AppleTV, Stream Music, Print, share files, etc  iTunes Wireless Sync is not working.  I've been watching the mDNS browser and using the Bonjour Browser on my MacBook and I notice a two odd things:
    1) I never see a a Layer 3 Multicast MGID Entry with the Apple Multicast Network (224.0.0.251) populate in the Multicats Window
    2) I have the service enabled for ITunesWirelessDeviceSharing (_apple-mobdev._tcp.local.) in my mDNS profile but I never see any device use that sting.  While watching the mDNS browser I do occasionally see the follwing: _apple-mobdev2._tcp.local. which is generated from the iPhone 5's.  I copied the string and created a new service and added it to my mDNS profile but still no joy.
    Any advice would be welcomed
    Chad

    Please check the Itune version
    Apple iOS v5.0+
    for implementing ITUNE please foillow the below links.
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0080bb1d7c.shtml

  • "Notes" only partially sync'd

    Hi.  I recently purchased my first Mac - iMac 27" late 2012.  At some point during the setup the Notes from my iPhone 4s got partially sync'd to the iMac.  There didn't seem to be a pattern, some old, some new, but only about 7 or 8 out of several dozen ended up on the iMac.  It looks like a couple of recent Notes are also now on the iMac. 
    As I sit here testing this, I can create a new note on the iPhone and it will sync to the iMac, and vice versa.  This occurs over the wifi or if the iPhone is connected directly. Doesn't matter.
    There are some notes dated on the iPhone many months before I purchased the iMac that are displayed on the iMac, and if I edit one of them on the phone or mac the change is sync'd.
    There are other notes on the iPhone that even if I edit them they don't sync to the iMac.
    iPhone: 7.0.4
    iMac: 10.9.1
    This isn't a big deal, but one of those things that just bugs me becuase it doesn't seem to be working!
    Thanks a lot for the help.
    Gary

    OK I figured out the category distinction - just a matter of Notes being stored locally on iPhone or on iCloud.  Did a lot of Googling and found a lot of discussion about this, but no straight forward method to transfer Notes stored "On My Phone" to iCloud.  I tried disabling Notes on  both iMac and iPhone and re-enabling, but that doesn't seem to do anything. 
    This isn't a new issue.  I see threads going back several years.
    Any suggestions how to get Notes in "On My iPhone" to iCloud?

  • Partial sync to iPhone

    Hi,
    The most recent two events in my iPhoto library are only partially syncing to my iPhone. I tried making them into an Album instead but the same thing happens.
    14 out of 82 photos and 3 out of 9 photos have synced, but not the others.
    Older events have a 100% sync.
    There is over 10GB free on the iPhone (32GB), and over 140 GB free on my hard drive.
    I have started iPhoto holding Cmd-Opt and selecting the option to rebuild the file permissions with no joy.
    Or is it an iTunes problem?

    Update: deleting the iPod Photo Cache solved the sync for my iPhone, but iTunes will not sync some events with an iPod Touch.
    Should I try to restore the Touch?

  • Partial collection Failure for nexus 5548UP in PI 2.1

    Hi there,
    I get "Partial Collection Failure" in the inventory collection status in Prime Infrastructure for all my Nexus 5548UP (8 devices).
    i have seen in the PI 2.1 release notes that a bug CSCum16230  which look like my problem has been resolved in PI 2.1 but i continue getting the "partail collection failure"
    Would like to know if the bug is still exist or get any other help to solve this problem.
    Regards,
    Alon.

    hello
    I have this problem as well...
    we've got four N5K-C5548UP. Two with a layer 3 daughter card and two without.
    interestingly we see the issue just on those boxes with the l3 daughter cards N55-D160L3-V2 installed...
    Any help or ideas are highly appreciated
    regards
    roman
    Sh inventory:
    OK:
    device-a# sh module
    Mod Ports Module-Type Model Status
    1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
    3 0 O2 Non L3 Daughter Card N55-DL2 ok
    Mod Sw Hw World-Wide-Name(s) (WWN)
    1 5.1(3)N2(1c) 1.0 --
    3 5.1(3)N2(1c) 1.0 --
    NOT OK:
    device-b# sh modu
    Mod Ports Module-Type Model Status
    1 32 O2 32X10GE/Modular Universal Pla N5K-C5548UP-SUP active *
    3 0 O2 Daughter Card with L3 ASIC N55-D160L3-V2 ok
    Mod Sw Hw World-Wide-Name(s) (WWN)
    1 5.1(3)N2(1c) 1.0 --
    3 5.1(3)N2(1c) 1.0 --

  • Standby reload due to Bulk-sync failure due to PRC mismatch on 3650

    Cisco-3650#show redundancy config-sync failures prc
    PRC Failed Command List
    interface GigabitEthernet1/1/1
     ! <submode> "interface"
    - channel-group 9 mode active
     ! </submode> "interface"
    interface GigabitEthernet1/1/2
     ! <submode> "interface"
    - channel-group 9 mode active
     ! </submode> "interface"
    software version: 03.03.02SE
    We are experiencing the same errors, we are going to upgrade the version to 03.03.04 to see if this fixes the problem.
    Update : moving to new version and of course rebooting the device resolved this issue. Paul.

    Cisco-3650#show redundancy config-sync failures prc
    PRC Failed Command List
    interface GigabitEthernet1/1/1
     ! <submode> "interface"
    - channel-group 9 mode active
     ! </submode> "interface"
    interface GigabitEthernet1/1/2
     ! <submode> "interface"
    - channel-group 9 mode active
     ! </submode> "interface"
    software version: 03.03.02SE
    We are experiencing the same errors, we are going to upgrade the version to 03.03.04 to see if this fixes the problem.
    Update : moving to new version and of course rebooting the device resolved this issue. Paul.

  • Itry to sync my iphone 5 ,after saying sync succesful sync failure appears

    after getting sync succesful a couple sync failure appears  when trying to sync iphone 5 to car

    I have re-authorised my computer, but not synced yet.
    All Mozy did was to copy everything under C:\Users\Mark Moss\Music\iTunes\iTunes Music, to a backup folder of the same name on mozy.com. So when I restored my hard drive's data, the iTunes was put back.
    Under C:\Users\Mark Moss\Music\iTunes\Mobile Applications on my (repaired) laptop, I now don't have any mobile apps listed (I guess I'd forgotten to back those up but in any case they're on my iPhone) so I'm concerned that if I replace my iPhone, I'll lose the apps, which I want to avoid.

  • Sync failure because itunes cannot connect to the sync server PLEASE HELP!!

    HELP! I cannot get my info back into my iphone.
    During sync I get an error message that says 'sync failure because itunes cannot connect to the sync server''
    I have had this problem today so i restored the iphone and it has synched the ipod portion but will not sync calenders, contacts , email accounts or bookmarks.
    The restore erased all of these and now i cannot replace them.
    Thank you in advance for any help in solving this crisis.

    I had the same problem (not from day one but within the past couple months). Anyway, I wish I had made note of everything that the quick-and wonderful-Apple support did when I finally decided to give them a call today-after getting tired of not being able to update calendars and contacts and not seeing any helpful info here-unfortunately, I continue that legacy (as I can't remember everything I had to do to fix-sorry) Ultimately involves creating a new user I called mine IPHONE...then doing some of this and that-and finally merging info and going to "Terminal" and typing in some code...then deleting some of the old files, Took about twenty-minutes on the phone. Sorry I didn't think ahead for others and write al this down...but just know the Apple people were great. I talked to a gal for about ten minutes very methodically trouble-shooting. When nothing worked she shifted me over to a real nice guy who calmly and politely guided me through all the steps to fix this annoying problem. I hate to say it, but just get on the phone and-if you have the same experience as me-you will get 5 Star treatment and your sync will work like a dream. Every time I have to contact Apple Support (which isn't that often) my experience is nothing but the best. Unbelievable customer service! Methodical, Personable, and truly knowledgeable! There is a fix and it works like a dream. Not that hard but you'll need customer service to walk you through it-as I can't (sorry I can't be of much help...) Good luck!

  • Cisco Prime 2.1- Partial collection failure

    Dear Experts,
    We are seeing many devices (around 1000+ devices) showing as "partial collection failure". We found this coz of not updated Telnet/SSH Cli username and password. So instead of editing each and every device, is there any way to select all devices and update cli credentials in one shot..?
    If someone helps me this option, it will be so helpful.

    Hi ,
    Other way is to export all the devices , Edit it and then Import it.
    Operate >device workcenter >   EXPORT device \ BULK IMPORT
    Thanks-
    Afroz
    ****Ratings Encourages Contributors ****

Maybe you are looking for