Partially loading webpages

My iMac is partially loading webpages. I have to constantly hit refresh, sometimes multiple times, to load a page. This isn't specific to any browser; I've tried Safari, Chrome and Firefox and they're all responding the same. It also isn't an issue with my ISP or router because 1) our other computers in the office on the same network are okay, and 2) I connected to a different wifi network and had the same problem.
I've disabled IPv6 but that didn't solve the problem. Any other ideas?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Similar Messages

  • Safari loads (freezes loading) webpages very slow on iPhone 4

    Hi!
    I have a problem with Safari on my iPhone 4 (4.2.1). Since I upgraded to 4.2.1 a week ago Safari is very slow and in 80% of time wont load webpages with first time when in 3G mode with strong bars. Well it loads them but very slowly (It takes approximately 20-30 seconds to load google or other pages). Maybe it would be more precisely to say that it starts to load, than the blue progress bar just stops at around 1/2cm and than after 20-30 seconds it actually starts to open the page and the blue progress bar continues to move. Sometimes (not often) after those 20-30 seconds I get message that page can't be opened cause server stopped to respond...
    What is important to my mind is that if I press reload while Safari is loading a webpage it opens fast as it should. So it usually works with second try.
    Since I noticed this problem after I upgraded to 4.2.1 I think those two things have connection (4.2.1 and Safari problem) but I might be wrong.
    This is happening in different locations around the city and it is not problem with coverage...I have three, four or sometimes even 5 bars 3G.
    Anybody having the same problem or can help me with some advice?
    Thank you!

    Safari Problems
    Safari - Unsupported third-party add-ons may cause Safari to unexpectedly quit or have performance issues
    Safari 5.0.1 or later - Slow or partial webpage loading, or webpage cannot be found

  • Cannot directly open the browser from the icon. "problem loading webpage" and "timed out" are the messages. Access was accomplished by using yahoo messenger and opening my email. if I attempt to open a new page, I recieve the aforementioned warnings.

    no link to open access to the internet. I used Yahoo Messenger, clicked on the 'mail icon' and since Firefox is my default it opened and I was able to continue from there. If I try to click File, open New Page, I get the "problem loading webpage" and "connection timed out" messages

    changed my homepage to Yahoo. Now Firrefox works but still cannot access ANYTHING 'Google"!

  • A Critical error encountered while loading webpage.

    Was running 2.1.51  and when browsing to the status link while logged in to the web gui I got a blank web page with the following text:
    A Critical error encountered while loading webpage.
    Reboot router - log back in - can go anywhere except the status page -- get same error page
    made the mistake of downloading and upgrading firmware to 2.1.71   = upgrade completed successfully = presented with the new login screen confirming that the box is running the new code -- now when I log in - I don't get in rather the previous error page - and cant get anywhere.
    A Critical error encountered while loading webpage.
    the url is https://192.168.75.1/scgi-bin/platform.cgi   but it doesn't load only displays the error.
    could someone share another valid management url for the box so I can at least try to get in somewhere before attempting to factory reset this POS ;-(
    thanks.

    Thanks for the response.   Based on the number of crickets that I heard after asking the question, I did indeed factory reset the box.  Luckily I had a backup of the config so it wasn't too painful to restore.
    I beleive the root cause co-incided with the expiration of the trend micro web protection gateway service.
    For whatever reason, I did not receive any notification that the service was to expire but the error experienced was noticed just two days after the subscription expired...  I had successfully logged in without issue and was able to view the status tab only a week earlier.
    be sure to pay the cisco tax on time or they'll lock you out of your box was the lesson learned...

  • Firefox will not load webpages: no error message, just keeps on circling

    Firefox suddenly stopped loading webpages. The little circle with a ball just keeps on circling.
    I had just downloaded a backup for my wordpress site, and downloaded a windows update but postponed restart. I tried restarting the computer but it didn't change anything.

    Hello!
    Please provide the following information to better assist you: <br>
    *Firefox version
    *Operating system

  • Snow leopard 10.6.8 wifi connected, cant load webpages

    hi!
    just yesterday my computer showed this problem with the internet. as the title says, it is connected to the wifi network (as it has always been) but i face the following problems:
    i cant load new webpaged in google chrome and firefox (which are the ones that I actually use)
    i can load webpsged that were already saved as bookmarks.
    i can load webpages in safari
    my icon for dropbox shows a red cross icon
    utorrent works just fine
    outlook (the software) get's my new emails
    what i tried to solve it:
    checked that my wifi networks work perfectly fine with other devices in the house
    restart computer
    changed DNS to one that was suggested in another thread in this discussions site
    resetting NVRAM/PRAM
    checked that it is updated
    so, i read that some people had similar problems with the new 10.8.2 for mountain lion, or sth like that... but in my case i have snow leopard so i don't think thst's the problem

    Hi, this has worked for a few...
    Though all of these steps may or may not be needed, I'm including them all.
    Make a New Location, Using network locations in Mac OS X ...
    http://support.apple.com/kb/HT2712
    10.5, 10.6, 10.7 & 10.8…
    System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
    10.5.x/10.6.x/10.7.x instructions...
    System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
    The interface that connects to the Internet should be dragged to the top of the list.
    If using Wifi/Airport...
    Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
    For 10.5/10.6/10.7/10.8, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
    208.67.222.222
    208.67.220.220
    (There may be better or faster DNS numbers in your area, but these should be a good test).
    Click OK.

  • MacBook Black Late 2007 will not load webpages or data on wifi

    Hello,
    I was cleaning out my MacBook's fan last night and was able to seal it up and boot it up successfully, it would recognize and connect to Wi-Fi networks, but would not load webpages or data. PLEASE HELP!!!
    MacBook 3,1
    2.2 GHZ INTEL CORE 2 DUO
    2 GB 667 MHZ SDRAM
    250 GB OWC MERCURY ELECTRA 3G SSD

    Hi chris_flies,
    If you are having WiFi connection issues with your MacBook, you may find the following article helpful:
    Wi-Fi: How to troubleshoot Wi-Fi connectivity
    http://support.apple.com/kb/HT4628
    Regards,
    - Brenden

  • Loading webpage problems

    hey guys,
    Im having a bunch of problems with loading webpages all of a sudden. I have Mozilla, firefox, and netscape. (accidently deleted safari) and cant get it back until I upgrade from 10.2.8 to at least OS 10.3. Anyway, I have problems getting onto Ebay it all started with Mozilla and once I found out that it wouldnt let me on I switched to firefox after 2 to 3 days later I started using netscape now I cant get on at all using any browser. Even on some of my other pages it loads the page just fine but has troubles loading the pictures. Why am I having so many problems I think its a software problem. I took my computer home over thanksgiving cause I was having the same problems before then and hooked it up to the network at my other house and it worked great there I had everything back. Now its all gone again. Why? I dont think its a networking problem but a software issue.( I need help with in the next 12 hours before 2 pm central time).

    The Solution?
    REINSTALL OSX using the Install DVD.
    I called APPLE Support and we went through a troubleshooting process to rule out Network Issues, Software Issues, File Issues and Hardware Issues. This process was very thorough.
    In the end, we used the Operating System Installation DVD to reinstall the system, which took about 60 minutes including downloading the updates. Reinstallation did not affect any files or lose any applications. Everything was as I left it -- nothing was missing. Easy.
    Now everything is back to normal.

  • Partially loading web page

    I am having a problem with web pages that are only partially loading. If I hold down the ctrl+f5 it loads it but as soon as I release the keys it goes back to being partially loaded. I would be really grateful if anyone can help, as i process my sales orders online and can only see the order headers, so seriously affecting my ability to work.
    Any ideas

    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
    *Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
    *Do NOT click the Reset button on the Safe Mode start window
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

  • Safari will not load webpages

    Safari will not load web pages. The browser hangs and stops loading completel and will not connect to the internet, even though I am perfectly connected to wifi...so I know it's not the wifi that's a problem. I have looked through multiple forums for troubleshooting safari to no avail.
    I know for a fact that the problem lies within safari SOMEWHERE, and since the only way for me to connect to the internet is through safari (i'm on a school network that doesn't allow me to connect to any other web browsers), I can't run any updates, reinstall safari, download any programs, etc.
    I'm totally stuck in a rut and I don't know what to do...help!

    Launch the Terminal application and copy or drag -- don't type -- the line below into the window:
    curl -I http://www.apple.com
    Press return. You should get several lines of output below what you entered, starting with this:
    HTTP/1.1 200 OK
    Is that what you get?
    Safari will not load webpages 
    I figured out a way to drag the link into the terminal application, and I did get lines of output starting with HTTP/1.1 200 OK

  • I have some web pages that loaded completely when using 3G but partially loaded using Wifi.

    I have some web pages that loaded completely when using 3G but partially loaded (only text without any images ) using Wifi. Is it a site specific issue?

    Can you rule out the NoScript extension as a cause of the issues on those sites? Even if you allow the main site to run scripts, often a website will spread its content over additional servers, so you may need to visit the "S" button menu a second or third time to get full functionality. (Over time, you'll recognize some the servers as being for ads, tracking, or sharing buttons and you can just let those parts of the page not work.)

  • Itunes sound distorted when loading webpages

    Hi,
    I recently got a new laptop (like a week ago) and installed iTunes 9. This worked fine at first, but starting yesterday the sound gets distorted half the time I load webpages or open applications.
    I've had this before on older computers, and assumed it was because of their limited technical capabilities. I don't think that's the case here, though.
    Does anyone have any idea where the problem could be situated? Or might it be technical after all?
    Thanks in advance!
    Greetings,
    Steven

    Sounds like your audio midi settings are not being stored properly.
    I'd try deleting com.apple.audio.AudioMIDISetup.plist and resetting
    audio midi.
    As you know, iTunes only reads the audio midi settings when it starts
    up, so I'd do that with itunes not running.

  • IPhone using Mac Mini's internet connection sharing, stops loading webpages

    Bought an iPhone 1 hour ago.
    I'm sharing my internet connection to my iBook and MacBook from my Mac Mini. Works fine.
    Can't connect using the iPhone.
    It will detect the network, it will show full network reception, but it will only load webpages for the first 10 seconds and then stops.
    Tried removing the password, fixing a channel, resetting the iPhone (full reset), the "forget this network" trick, nothing worked.
    It will load web pages in the first 10 seconds of detecting my open network. Its highly frustrating...
    Any suggestions? Maybe using the restore option from iTunes instead of the reset ones from iPhone? Will this try to reinstall the latest firmware?

    Very similar case here -- I bought an iPhone just yesterday, set it up with internet sharing on my Mac Mini, and am getting random (but frequent) failures connecting via wifi. Small web pages can get through sometimes, large (or complex) web pages almost always hang during loading, e-mail pretty much never works.
    However, using "edge" works just fine.
    I've nosed around these forums a bit (and googled for this problem a bit), and it does seem like there are a number of users having this sort of trouble. However, some folks with this problem have noted that they can run wifi just fine at other hotspots. (I haven't taken my phone to another hotspot yet, maybe I'll try tomorrow...) And I've shared my internet connection to other PCs from my Mini successfully before. So, in my opinion, this problem does not appear to be an actual hardware fault in either the iPhone or the Mac Mini, but rather some disagreement between the settings chosen on both sides; my guess is that this'll take a driver modification in either or both to fix, rather than a replacement of either the iPhone or the Mini.
    Just my current guess, though.
    --John

  • UoM error while doing partial loading in O4G1- TD Transport

    Hi experts,
    while doing partial loading error pops up which says UoM not set in customizing..
    Have checked all settings for Uom its ok..
    what else could be the issue..pls help.
    regards,
    VP

    Hi,
    Data records for package 39 selected in PSA - 2 error(s). Record 5129 :No SID found for value 'EMN ' of characteristic 0BASE_UOM . Record 5132 :No SID found for value 'EMN ' of characteristic 0BASE_UOM
    The issue with record no. 5129 and 5132.
    In PSA check errorneous records and it will display only the error records, you just edit as per the require and try reloading into cube.
    Deleting single record is not possible.
    Let us know if you still have any issues.
    Reg
    Pra

  • Web browsers not loading webpages

    Overnight, a couple of days ago, my web browsers (Safari and Chrome) both stopped loading webpages. When I click on a link, I get a blank page. But when I am logged as a guest or browse through Vmware's windows I can still browse normally. Thanks for helping to fix this.

    Thank you Carolyn,
    I've got Sophos installed from long time ago. That's the only antivirus that is installed.
    Checking in firewall settings didn't help I think, cause even after desactivating the firewall temporaly didn't fix the issue in both web browsers.
    This issue is not discussed in Mac malware guide.
    Another detail, is that some web content will load like this discussion group or google search. But If I click on any item from google search, the page won't load.

Maybe you are looking for

  • Delta not working after upgrade from 3.5 to BI7.0

    Hello All, We have recently upgraded from BW3.5 to BI7.0 and the standard delta is not working now after the upgade. The name of the Extractor is 0CRM_SALES_ACT_1. Did anyone come across this problem before or  can anyone suggest the solution. Thanks

  • Select from sys.all_ind_columns works in sql*plus but not in stored proc

    I'm writing a query to find duplicate rows in a temporary table which has no unique index defined before I insert the data into the real table. I'm trying to query the sys.all_ind_columns view for the target table which belongs to a different schema:

  • Case problems

    Okay, so I have a MSI K8N Neo Platinum motherboard fitted with an AMD Athlon 64 3700+ (socket 754) in my Thermaltake Soprano case. This case came with a panel with 1 firewire connection, 2 USB connections and a Mic/audio port. The problem is, I can't

  • Dynamic sizing of Column Width

    Is there a way that the table columns can be dynamically adjusted widthwise in an RTF template ? I do not want my $Total to wrap around.

  • Samsung SCX 4500 - Scanner no longer works since OS Update to 10.5.6

    Hi all, my problem is already described in the subject line The problem should have disturbed more people than just me. Installing the latest drivers from Samsung did not do the job Question: Anybody got the fix? Samsung is rather clueless on this on