Partition failed with error input output

Hi All,
I installed a new hard drive (WD 500G) into my 2006 Macbook, Mac OS X 10.4.10. I also increased the RAM to 2G. My Macbook reconized the hard drive. However, I followed the steps below to format the HD, but got the partition failed with error input output msg.
1. Went to Disk Utility, selected the name of new hard drive in the sidebar.
2. Select the Partition tab, and selected 1 partition from the drop down menu.
3. Click Options, then choose GUID .
4. Select Partition
In previous posts someone suggested updating the softward to 10.4.11 or the erasing the HD, but erasing the hard drive would take 13 hours according to my Macbook. Any suggestions? Please Help!

The error usually means the drive is bad. But you can try this:
Erase and Install OS X
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
7. After formatting has finished quit DU and return to the installer. Install OS X.

Similar Messages

External Drive Disk Erase Failed with the Error Input/Output Error

I have 2 hard drives in an external FW800 enclosure that I am unable to format. When I go to initialize the drives in Disk Utility, I get the following error message: "Disk Erase failed with the error: Input/output error."
The drives show up in Disk Utility, but I can't repair them (that option is grayed out). Disk Utility correctly ID's the manufacturer of the drives (Maxtor), their size (200gb each), so it's obviously seeing that the drives are there. But it won't let me format them.
The drives are new, by the way; they don't have any data/files on them. I have Disk Warrior, but the drives don't show up there to be repaired -- probably because they aren't formatted yet.
After looking at other posts, I tried switching the jumper settings around on the drives -- from Master/Slave to cable select and back again, but it didn't help. I also tried doing a zero erase (even though the drives are new), zapping the PRAM -- again, no help.
One question I had is whether this could be a bad FW800 cable? The cable is new -- it came with the enclosure, which is an OWC Dual FW 800 enclosure. Other than that, does anyone have any other thoughts about what's causing this? Any help would be greatly appreciated.
Matthew

SOLUTION!!!!
I had the exact same problem. I have the original 20 GB hard drive that came in my Powerbook G4 550MHz and a couple of years ago I traded up for a 60 GB drive and bought a FW/USB enclosure for my original drive to use it to backup my important files. I hadn't backed up in over a year (shame on me!) and I decided maybe I should erase the drive and start from scratch. It was connected via USB.
At that point DiskUtility gave me the exact same Input/Output error. I tried partitioning the drive into 1 or more partitions but came up with the same error. I couldn't figure out what was wrong so I decided to startup in OS 9.2.2, I did that and let it start up, then plugged in the hard drive and it gave me the standard "This disk is unrecognizable, do you want to eject or erase?" so I clicked Initalize. It worked!
Just make sure you choose the MacOS Extended option when initializing out of OS 9 (instead of the MacOS Standard option) so it can be read and viewed in OS X.
If your computer is too new to be able to boot from an OS 9 folder on your drive or an OS 9 CD, then see if a friend or a local library has older computers that are running OS 9 or can boot from it. If not let me know and you can send me your drive and I'll reformat it.
Kind of crazy...I haven't used the OS 9 partition on my HD in YEARS...was even thinking about erasing it since I don't use any Classic applications anymore...good thing I didn't!
Nick
Powerbook G4 550Mhz Mac OS X (10.4.6)

Partition Failed Partition failed with the error: POSIX reports: The operation couldn't be completed. CAN NOT ALLOCATE MEMORY

I plug usb mass storage device to my macbook pro i7 than every thing is stack and i reinforce to shutdown and than I start again but mac fail to boot again.
I tried different optiones in disk utility in mac os startup disk. but still fail to repair, erase and partition. I try to fix with the steps listed in
https://discussions.apple.com/message/13288923#13288923
but it fail to partition with the msg:
Partition Failed
Partition failed with the error: POSIX reports: The operation couldn’t be completed.cannot allocate memory
pls pls pls help urgentely on this matter I stop working.
Kind Regards,
pe

Hi again OGELTHORPE.
I've already run two hardware tests. One quick one and one extended one. It was unable to pick anything up.
It's like everything is running perfectly, but when I go to erase the HDD or partition it, it pops up with the error message. Even when I try to erase and partition using "Terminal", I received the same error message.
It's beginning to do my head in, but will see if replacing the SATA cable will make any difference. If it doesn't, I'll hazard a guess it could be the Logic Board.
Thanks again for your suggestions!
L.

Partition failed with the error: No space left on device

I used Boot Camp Assistant (for instaling Windows XP) and there was Partition error:
+*The disc cannot be partioned because some files cannot be moved.*+
+Back up the disk and use Disk Utility to format it as a single Mac OS Extended (journaled) volume. Restore your information to the disk and try using Boot Camp Assistand again.+
so I tried Yasu, verified permission, verified disk, and everything was ok, but in Disk Utility I was trying to split or change size of my disk but there is one error again:
+*Partition failed.*+
+Partition failed with the error: No space left on device+
but I have 64GB free space!
how must I "+Restore your information to the disk+" or what else can I do?
thanks!

arajs wrote:
I used Boot Camp Assistant (for instaling Windows XP) and there was Partition error:
+*The disc cannot be partioned because some files cannot be moved.*+
+Back up the disk and use Disk Utility to format it as a single Mac OS Extended (journaled) volume. Restore your information to the disk and try using Boot Camp Assistand again.+
so I tried Yasu, verified permission, verified disk, and everything was ok, but in Disk Utility I was trying to split or change size of my disk but there is one error again:
+*Partition failed.*+
+Partition failed with the error: No space left on device+
but I have 64GB free space!
how must I "+Restore your information to the disk+" or what else can I do?
thanks!
This is a standard error message.
If you would have checked into the bootcamp forum you would have instantly found the solution.
http://discussions.apple.com/forum.jspa?forumID=1244&start=0
All that error message means is that you do not have enough conguous disk space available. No big deal at all for an older system. You have bits of files strewn over the "free space."
The solution as you would find in the bootcamp forum is to clone your HD, using a file-file clone, then test the clone to be sure it is working and then to erase your HD and clone back.
Works every time.
Message was edited by: Theodore

I get the following error when formatting a external hard drive. Partition failed with the error: POSIX reports: The operation couldn't be completed. Cannot allocate memory

I get the following error when formatting a external hard drive.
Partition failed with the error:
POSIX reports: The operation couldn’t be completed. Cannot allocate memory
I have a Macbook pro 13" A1278. I purchased it around december 2010. I have a HHD 3.5" drive desktop select II 1.5TB. I purchased it around Febuary/March 2011 to use with my Macbook pro. I formatted it and moved all my files to there, I got it so my macbook's hard drive wouldn't brake and I lose everything on my macbook.
Is there any fixes?

First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."

Partition failed with the error: The target Core Storage volume is locked

partition failed with the error: The target Core Storage volume is locked
Hello everybody!
Please help me.
I'm using MacBook Pro (Retina, 13-inch, Mid 2014), Processer:2.6 GHz Intel Core i5, Memory: 8 GB 1600 MHz DDR3.
my computer i have divided in 3 drives: 1-Machintosh HD (Mac OS) 2-Bootcamp (Window OS) & 3-Data (drive for data storage).
I don't want to use Window OS on my computer anymore so I decided to delete drive Data (the third drive) & Window OS (the second drive).
I want my hard drive become a single drive back but when I was formatting, there were some problem display:
then i clicked ok and it displayed like this:
then i try to format or create new partition, it's nothing happen when press button apply.
my computer has storage space 256GB but now when it is happened like this my storage space is only 127GB only.
so please help me.. what so I do with this problem.
Thank you.!

arajs wrote:
I used Boot Camp Assistant (for instaling Windows XP) and there was Partition error:
+*The disc cannot be partioned because some files cannot be moved.*+
+Back up the disk and use Disk Utility to format it as a single Mac OS Extended (journaled) volume. Restore your information to the disk and try using Boot Camp Assistand again.+
so I tried Yasu, verified permission, verified disk, and everything was ok, but in Disk Utility I was trying to split or change size of my disk but there is one error again:
+*Partition failed.*+
+Partition failed with the error: No space left on device+
but I have 64GB free space!
how must I "+Restore your information to the disk+" or what else can I do?
thanks!
This is a standard error message.
If you would have checked into the bootcamp forum you would have instantly found the solution.
http://discussions.apple.com/forum.jspa?forumID=1244&start=0
All that error message means is that you do not have enough conguous disk space available. No big deal at all for an older system. You have bits of files strewn over the "free space."
The solution as you would find in the bootcamp forum is to clone your HD, using a file-file clone, then test the clone to be sure it is working and then to erase your HD and clone back.
Works every time.
Message was edited by: Theodore

703: Subdaemon connect to data store failed with error TT9999

All,
I'm getting the following error whilst trying to connect to a TimesTen DB:
connect "DSN=my_cachedb";
703: Subdaemon connect to data store failed with error TT9999
In the tterrors.log:
16:39:24.71 Warn: : 2568: 3596 ------------------: subdaemon process exited
16:39:24.71 Warn: : 2568: 3596 exited while connected to data store '/u01/ttdata/datastores/my_cachedb' shm 33554529 count=1
16:39:24.71 Warn: : 2568: daRecovery: subdaemon 3596, managing data store, failed: invalidate (failcode=202)
16:39:24.71 Warn: : 2568: Invalidating the data store (failcode 202, recovery for 3596)
16:39:24.72 Err : : 2568: TT14000: TimesTen daemon internal error: Could not send 'manage' request to subdaemon rc -2 err1 703 err2 9999
16:39:24.72 Warn: : 2568: 3619 Subdaemon reports creation failure
16:39:24.72 Err : : 2568: TT14000: TimesTen daemon internal error: Deleting 3619/0x1558650/'/u01/ttdata/datastores/my_cachedb' - from association table - not found
16:39:24.72 Err : : 2568: TT14004: TimesTen daemon creation failed: Could not del from dbByPid internal table
16:39:24.81 Warn: : 2568: child process 3596 terminated with signal 11
16:39:25.09 Err : : 2568: TT14000: TimesTen daemon internal error: daRecovery for 3619: No such data store '/u01/ttdata/datastores/my_cachedb'
I've checked and the datastore does exist and is owned by the timesten UNIX user.
ttversion:
TimesTen Release 11.2.2.2.0 (64 bit Linux/x86_64) (tt1122:53396) 2011-12-23T09:26:28Z
Instance admin: timesten
Instance home directory: /home/timesten/TimesTen/tt1122
Group owner: timesten
Daemon home directory: /home/timesten/TimesTen/tt1122/info
PL/SQL enabled.
Datastore definition from sys.odbc.ini:
[my_cachedb]
Driver=/home/timesten/TimesTen/tt1122/lib/libtten.so
DataStore=/u01/ttdata/datastores/my_cachedb
LogDir=/u01/ttdata/logs
PermSize=40
TempSize=32
DatabaseCharacterSet=AL32UTF8
OracleNetServiceName=testdb
Kernel parameters from sysctl -a:
kernel.shmmax = 68719476736
kernel.shmall = 4294967296
Memory / SWAP:
MemTotal: 2050784 kB
SWAP: /dev/mapper/VolGroup00-LogVol01 partition 4095992
I'm new to TimesTen and I'm planning on evaluationg it to see if it could solve an issue we're having. Any suggestions would be much appreciated.
Thanks,
Ian.

Hi Ian,
Can you please answer the following / provide the following information:
1. What are your kernel parameters relating to semaphores set to? Is anything else on the mahcine using significant numbers of semaphores?
2. Please provide the output of the following shell commands:
ls -ld /u01
ls -ld /u01/ttdata
ls -ld /u01/ttdata/datastores
ls -ld /u01/ttdata/logs
3. Please provide an excerpt of the detailed message log (ttmesg.log) between around 16:38 and 16:40 (i.e. from a little while before the problem until after the problem).
Thanks,
Chris

Preverification failed with error code 1. BUILD FAILED

Hallo Oracle,
Am learning my first J2me application and when i build it am getting this error. can some one help me understand what it means
Created dir: C:\Users\Dell\Documents\NetBeansProjects\watsdownapp\build\preverifysrc
Copying 1957 files to C:\Users\Dell\Documents\NetBeansProjects\watsdownapp\build\preverifysrc
Created dir: C:\Users\Dell\Documents\NetBeansProjects\watsdownapp\build\preverified
Preverifying 1957 file(s) into C:\Users\Dell\Documents\NetBeansProjects\watsdownapp\build\preverified directory.
Error preverifying class com.sun.activation.registries.MailcapFile
    VERIFIER ERROR com/sun/activation/registries/MailcapFile
.<init>(Ljava/lang/String;)V:
Cannot find class java/util/Map
C:\Users\Dell\Documents\NetBeansProjects\watsdownapp\nbproject\build-impl.xml:431: Preverification failed with error code 1.
BUILD FAILED (total time: 25 seconds)
this is the contents of build-impx.xml
<?xml version="1.0" encoding="UTF-8"?>

<project name="watsdownapp-impl" default="jar" basedir="..">
    
    <target name="pre-load-properties">
        <property file="nbproject/private/private.properties"/>
        <property name="user.properties.file" location="${netbeans.user}/build.properties"/>
        <available property="user.properties.file.exists" file="${user.properties.file}"/>
    </target>
    <target name="exists.config.active" unless="config.active">
        <echo level="warning" message="Active configuration (config.active property) is not set - using default."/>
        <property value="" name="config.active"/>
    </target>
    <target name="exists.netbeans.user" unless="netbeans.user">
        <echo level="warning" message="NetBeans IDE user directory (netbeans.user property) is not set. By specifying this property many properties required by the project will be automatically evaluated (e.g.: ant-ext library home, ...). You could also open this project in the NetBeans IDE - in this case this property would be set automatically."/>
    </target>
    <target name="exists.user.properties.file" unless="user.properties.file.exists">
        <echo level="warning" message="User properties file (user.properties.file) property is not set. By specifying this property many properties required by the project will be automatically evaluated (e.g.: libraries, platforms, ...)."/>
    </target>
    <target name="load-properties" depends="pre-load-properties,exists.config.active,exists.netbeans.user,exists.user.properties.file">
        <loadproperties srcfile="nbproject/project.properties">
            <filterchain>
                <containsregex pattern="^configs\.${config.active}\.(.*)" replace="\1"/>
                <concatfilter prepend="nbproject/project.properties"/>
                <containsregex pattern="^platform.active=|^deployment.method=|^deployment.instance="/>
            </filterchain>
        </loadproperties>
        <property name="deployment.instance" value="default"/>
        <loadproperties srcfile="${user.properties.file}">
            <filterchain>
                <replaceregex pattern="^platforms\.${platform.active}\." replace="platform."/>
                <replaceregex pattern="^deployment\.${deployment.method}\.scriptfile=" replace="deployment.scriptfile="/>
                <replaceregex pattern="^deployments\.${deployment.method}\.${deployment.instance}\.([^=]+)=" replace="\1="/>
            </filterchain>
        </loadproperties>
        <loadproperties srcfile="nbproject/project.properties">
            <filterchain>
                <containsregex pattern="^configs\.${config.active}\.(.*)" replace="\1"/>
                <concatfilter prepend="nbproject/project.properties"/>
            </filterchain>
        </loadproperties>
    </target>
    
    <target name="exists.platform.active" unless="platform.active">
        <echo level="warning" message="Active platform (platform.active property) in not set. If you set this and user.properties.file property, many properties required by the project will be automatically evaluated (e.g.: platform home, platform classpath, ...)."/>
    </target>
    <target name="exists.platform.configuration" unless="platform.configuration">
        <echo level="warning" message="Platform configuration (platform.configuration) is not set. Using default (CLDC-1.0) configuration."/>
        <property name="platform.configuration" value="CLDC-1.0"/>
    </target>
    <target name="exists.platform.profile" unless="platform.profile">
        <echo level="warning" message="Platform profile (platform.profile) is not set. Using default (MIDP-1.0) profile."/>
        <property name="platform.profile" value="MIDP-1.0"/>
    </target>
    <target name="basic-init" depends="exists.platform.active,exists.platform.configuration,exists.platform.profile">
        <fail unless="libs.j2me_ant_ext.classpath">Classpath to J2ME Ant extension library (libs.j2me_ant_ext.classpath property) is not set. For example: location of mobility/modules/org-netbeans-mobility-antext.jar file in the IDE installation directory.</fail>
        <fail unless="platform.home">Platform home (platform.home property) is not set. Value of this property should be ${platform.active.description} emulator home directory location.</fail>
        <fail unless="platform.bootclasspath">Platform boot classpath (platform.bootclasspath property) is not set. Value of this property should be ${platform.active.description} emulator boot classpath containing all J2ME classes provided by emulator.</fail>
        <fail unless="src.dir">Must set src.dir</fail>
        <fail unless="build.dir">Must set build.dir</fail>
        <fail unless="dist.dir">Must set dist.dir</fail>
        <fail unless="dist.jar">Must set dist.jar</fail>
        <property name="javac.source" value="1.3"/>
        <property name="javac.target" value="1.1"/>
        <property name="javac.encoding" value="${file.encoding}"/>
        <property name="deployment.number" value="0.0.1"/>
        <property name="deployment.counter" value="000002"/>
        <condition property="no.deps">
            <istrue value="${no.dependencies}"/>
        </condition>
        <condition property="no.preprocess">
            <isfalse value="${use.preprocessor}"/>
        </condition>
        <condition property="no.javadoc.preview">
            <isfalse value="${javadoc.preview}"/>
        </condition>
        <condition property="filter.excludes.evaluated" value="${filter.excludes},${filter.more.excludes},**/*Test.java,**/test,**/test/**">
            <istrue value="${filter.exclude.tests}"/>
        </condition>
        <property name="filter.excludes.evaluated" value="${filter.excludes},${filter.more.excludes}"/>
        <condition property="deployment.do.override.jarurl" value="">
            <istrue value="${deployment.override.jarurl}"/>
        </condition>
        <condition property="config.active.name" value="DefaultConfiguration">
            <length string="${config.active}" trim="true" length="0"/>
        </condition>
        <property name="config.active.name" value="${config.active}"/>
        <taskdef resource="org/netbeans/mobility/antext/defs.properties">
            <classpath>
                <pathelement path="${libs.j2me_ant_ext.classpath}"/>
            </classpath>
        </taskdef>
        <condition property="skip.deployment">
            <equals arg1="${deployment.method}" arg2="NONE" casesensitive="false" trim="true"/>
        </condition>
        <condition property="app-version.autoincrement.trigger">
            <istrue value="${app-version.autoincrement}"/>
        </condition>
        <condition property="debug.timeout" value="30000">
            <or>
                <equals arg1="${debugger.timeout}" arg2="" trim="true"/>
                <not>
                    <isset property="debugger.timeout"/>
                </not>
            </or>
        </condition>
        <property name="debug.timeout" value="${debugger.timeout}"/>
        <nb-overrideproperty name="buildsystem.baton" value="${src.dir}"/>
    </target>
    
    <target name="cldc-pre-init">
        <condition property="cldc-platform.trigger">
            <equals arg1="CLDC" arg2="${platform.trigger}" casesensitive="false"/>
        </condition>
    </target>
    <target name="cldc-init" depends="cldc-pre-init" if="cldc-platform.trigger">
        <property name="preverify.sources.dir" location="${build.dir}/preverifysrc"/>
        <property name="manifest.build.file" location="${build.dir}/manifest.mf"/>
        <property name="platform.device" value=""/>
        <property name="dist.jad.url" value="file://"/>
        <property name="run.cmd.options" value=""/>
        <condition property="evaluated.run.security.domain" value="">
            <isfalse value="${run.use.security.domain}"/>
        </condition>
        <property name="evaluated.run.security.domain" value="${run.security.domain}"/>
        <condition property="override.jarurl.trigger">
            <and>
                <istrue value="${cldc-platform.trigger}"/>
                <istrue value="${deployment.override.jarurl}"/>
            </and>
        </condition>
        <property name="deployment.jad" location="${dist.dir}/${dist.jad}"/>
        <property name="deployment.jar" location="${dist.dir}/${dist.jar}"/>
        <property name="deployment.dir" location="${dist.dir}"/>
        <patternset id="deployment.patternset">
            <include name="${dist.jad}"/>
            <include name="${dist.jar}"/>
        </patternset>
    </target>
    
    <target name="cdc-init">
        <condition property="cdc-platform.trigger">
            <equals arg1="CDC" arg2="${platform.trigger}" casesensitive="false"/>
        </condition>
        <available file="${manifest.file}" property="manifest.available"/>
        <condition property="main.class.applet">
            <equals arg1="${main.class.class}" arg2="applet" casesensitive="false"/>
        </condition>
        <condition property="main.class.xlet">
            <equals arg1="${main.class.class}" arg2="xlet" casesensitive="false"/>
        </condition>
        <condition property="manifest.available+main.class+fat.jar">
            <and>
                <isset property="manifest.available"/>
                <isset property="main.class"/>
                <istrue value="${platform.fat.jar}"/>
                <not>
                    <equals arg1="${main.class}" arg2="" trim="true"/>
                </not>
            </and>
        </condition>
        <condition property="manifest.available+main.class">
            <and>
                <isset property="manifest.available"/>
                <isset property="main.class"/>
                <isfalse value="${platform.fat.jar}"/>
                <not>
                    <equals arg1="${main.class}" arg2="" trim="true"/>
                </not>
            </and>
        </condition>
        <condition property="application.version.invalid" value="true">
            <equals arg1="${deployment.number}" arg2="" trim="true"/>
        </condition>
        <fail if="application.version.invalid" message="Property deployment.number must not be empty and must contain version in format %d.%d.%d!"/>
        <condition property="sign.jar.trigger" value="true">
            <and>
                <isset property="cdc-platform.trigger"/>
                <istrue value="${sign.enabled}"/>
            </and>
        </condition>
    </target>
    
    <target name="semc-pre-init" if="cdc-platform.trigger">
        <condition property="semc-platform.trigger">
            <equals arg1="semc" arg2="${platform.type}" casesensitive="false"/>
        </condition>
    </target>
    <target name="semc-init" depends="semc-pre-init" if="semc-platform.trigger">
        <condition property="semc.icon.invalid" value="true">
            <or>
                <contains string="${semc.application.icon}" substring="$${"/>
                <equals arg1="${semc.application.icon}" arg2="" trim="true"/>
            </or>
        </condition>
        <condition property="no.certificateorkey" value="true">
            <or>
                <isset property="no.application.uid"/>
                <equals arg1="${semc.certificate.path}" arg2="" trim="true"/>
                <contains string="${semc.certificate.path}" substring="$${semc.certificate.path"/>
                <equals arg1="${semc.private.key.path}" arg2="" trim="true"/>
                <contains string="${semc.private.key.path}" substring="$${semc.private.key.path"/>
            </or>
        </condition>
        <property name="j9.dist" location="${build.dir}/j9/${semc.application.uid}.j9"/>
        <taskdef resource="org/netbeans/modules/j2me/cdc/project/defs.properties">
            <classpath>
                <pathelement path="${libs.cdc-ant-utils.classpath}"/>
            </classpath>
        </taskdef>
        <taskdef resource="org/netbeans/modules/j2me/cdc/project/semc/defs.properties">
            <classpath>
                <pathelement path="${libs.semc-ant-utils.classpath}"/>
            </classpath>
        </taskdef>
        <property name="deployment.dir" location="${dist.dir}"/>
        <patternset id="deployment.patternset">
            <include name="*.sis"/>
            <include name="*.SIS"/>
        </patternset>
    </target>
    
    <target name="savaje-pre-init" if="cdc-platform.trigger">
        <condition property="savaje-platform.trigger">
            <equals arg1="savaje" arg2="${platform.type}" casesensitive="false"/>
        </condition>
    </target>
    <target name="savaje-init" depends="savaje-pre-init" if="savaje-platform.trigger">
        <property name="savaje.application.uid" value="TBD"/>
        <condition property="savaje.bundle.base.invalid" value="true">
            <or>
                <equals arg1="${savaje.bundle.base}" arg2="" trim="true"/>
                <contains string="${savaje.bundle.base}" substring="$${savaje.bundle.base"/>
            </or>
        </condition>
        <condition property="savaje.unsupported.main" value="true">
            <or>
                <equals arg1="${main.class.applet}" arg2="true"/>
            </or>
        </condition>
        <condition property="savaje.icon.invalid" value="true">
            <or>
                <isset property="no.application.uid"/>
                <contains string="${savaje.application.icon}" substring="$${"/>
                <equals arg1="${savaje.application.icon}" arg2="" trim="true"/>
            </or>
        </condition>
        <property name="jnlp.dist" value="${build.dir}/jnlp/bundle.jnlp"/>
        <property name="deployment.dir" location="${dist.dir}"/>
        <patternset id="deployment.patternset">
            <include name="bundle.jnlp"/>
            <include name="bundle.policy"/>
            <include name="lib/*"/>
        </patternset>
    </target>
    
    <target name="sjmc-pre-init" if="cdc-platform.trigger">
        <condition property="sjmc-platform.trigger">
            <equals arg1="sjmc" arg2="${platform.type}" casesensitive="false"/>
        </condition>
    </target>
    <target name="sjmc-init" depends="sjmc-pre-init" if="sjmc-platform.trigger"/>
    
    <target name="ojec-pre-init" if="cdc-platform.trigger">
        <condition property="ojec-platform.trigger">
            <equals arg1="ojec" arg2="${platform.type}" casesensitive="false"/>
        </condition>
    </target>
    <target name="ojec-init" depends="ojec-pre-init" if="ojec-platform.trigger"/>
    
    <target name="cdc-hi-pre-init" if="cdc-platform.trigger">
        <condition property="cdc-hi-platform.trigger">
            <equals arg1="cdc-hi" arg2="${platform.type}" casesensitive="false"/>
        </condition>
    </target>
    <target name="cdc-hi-init" depends="cdc-hi-pre-init" if="cdc-hi-platform.trigger"/>
    
    <target name="nokiaS80-pre-init" if="cdc-platform.trigger">
        <condition property="nokiaS80-platform.trigger">
            <equals arg1="nokiaS80" arg2="${platform.type}" casesensitive="false"/>
        </condition>
    </target>
    <target name="nokiaS80-init" depends="nokiaS80-pre-init" if="nokiaS80-platform.trigger">
        <property name="j9.dist" location="${build.dir}/j9/NOKIA.j9"/>
        <property name="manifest.build.file" location="${build.dir}/manifest.mf"/>
        <condition property="nokia.icon.invalid">
            <or>
                <contains string="${nokiaS80.application.icon}" substring="$${"/>
                <equals arg1="${nokiaS80.application.icon}" arg2="" trim="true"/>
            </or>
        </condition>
        <property name="deployment.dir" location="${dist.dir}"/>
        <patternset id="deployment.patternset">
            <include name="${dist.jar}"/>
        </patternset>
    </target>
    
    <target name="pre-init"/>
    <target name="post-init"/>
    <target name="init" depends="pre-init,load-properties,basic-init,cldc-init,cdc-init,semc-init,savaje-init,sjmc-init,ojec-init,cdc-hi-init,nokiaS80-init,post-init"/>
    
    <target name="conditional-clean-init">
        <uptodate property="no.clean.before.build" targetfile="${build.dir}/.timestamp">
            <srcfiles dir="nbproject">
                <include name="project.properties"/>
                <include name="build-impl.xml"/>
            </srcfiles>
        </uptodate>
    </target>
    <target name="conditional-clean" depends="init,conditional-clean-init" unless="no.clean.before.build" description="Clean project in case its meta information has changed.">
        <antcall target="do-clean" inheritall="true" inheritrefs="true"/>
    </target>
    
    <target name="deps-jar" depends="conditional-clean" unless="no.deps"/>
    
    <target name="pre-preprocess"/>
    <target name="do-preprocess" unless="no.preprocess">
        <fail unless="preprocessed.dir">Must set preprocessed.dir</fail>
        <property name="abilities" value=""/>
        <property name="debug.level" value="debug"/>
        <mkdir dir="${preprocessed.dir}"/>
        <echo message="ignore me" file="${build.dir}/.timestamp"/>
        <nb-prep destdir="${preprocessed.dir}" preprocessfor="${config.active.name},${abilities},DebugLevel=${debug.level}" encoding="${javac.encoding}">
            <fileset dir="${buildsystem.baton}" defaultexcludes="${filter.use.standard}" excludes="${filter.excludes.evaluated}"/>
        </nb-prep>
        <copy todir="${preprocessed.dir}">
            <fileset dir="${buildsystem.baton}" defaultexcludes="${filter.use.standard}" excludes="${filter.excludes.evaluated},${build.classes.excludes}"/>
        </copy>
        <nb-overrideproperty name="buildsystem.baton" value="${preprocessed.dir}"/>
    </target>
    <target name="post-preprocess"/>
    <target name="preprocess" depends="deps-jar,pre-preprocess,do-preprocess,post-preprocess" description="Preprocess project sources."/>
    
    <target name="pre-compile"/>
    <target name="do-compile">
        <fail unless="build.classes.dir">Must set build.classes.dir</fail>
        <mkdir dir="${build.classes.dir}"/>
        <javac includeantruntime="false" source="${javac.source}" target="${javac.target}" deprecation="${javac.deprecation}" optimize="${javac.optimize}" debug="${javac.debug}" destdir="${build.classes.dir}" srcdir="${buildsystem.baton}" bootclasspath="${platform.bootclasspath}" encoding="${javac.encoding}">
            <classpath>
                <path path="${libs.classpath}"/>
            </classpath>
        </javac>
        <copy todir="${build.classes.dir}">
            <fileset dir="${buildsystem.baton}" defaultexcludes="${filter.use.standard}" excludes="${filter.excludes.evaluated},${build.classes.excludes}"/>
        </copy>
        <nb-overrideproperty name="buildsystem.baton" value="${build.classes.dir}"/>
    </target>
    <target name="extract-libs" description="Extracts all bundled libraries.">
        <mkdir dir="${build.classes.dir}"/>
        <nb-extract dir="${build.classes.dir}" excludeManifest="true" classpath="${libs.classpath}" excludeclasspath="${extra.classpath}"/>
    </target>
    <target name="post-compile"/>
    <target name="compile" depends="preprocess,pre-compile,extract-libs,do-compile,post-compile" description="Compile project classes."/>
    
    <target name="pre-compile-single"/>
    <target name="do-compile-single">
        <fail unless="javac.includes">Must select some files in the IDE or set javac.includes</fail>
        <mkdir dir="${build.classes.dir}"/>
        <javac includeantruntime="false" source="${javac.source}" target="${javac.target}" deprecation="${javac.deprecation}" optimize="${javac.optimize}" debug="${javac.debug}" srcdir="${buildsystem.baton}" destdir="${build.classes.dir}" bootclasspath="${platform.bootclasspath}" includes="${javac.includes}" encoding="${javac.encoding}">
            <classpath>
                <path path="${libs.classpath}"/>
            </classpath>
        </javac>
    </target>
    <target name="post-compile-single"/>
    <target name="compile-single" depends="preprocess,pre-compile-single,do-compile-single,post-compile-single" description="Compile selected project classes."/>
    
    <target name="proguard-init" description="Up-to-date check before obfuscation.">
        <property name="obfuscation.level" value="0"/>
        <condition property="no.obfusc">
            <or>
                <equals arg1="${obfuscation.level}" arg2="0"/>
                <uptodate targetfile="${obfuscator.destjar}">
                    <srcfiles dir="${buildsystem.baton}"/>
                </uptodate>
            </or>
        </condition>
        <uptodate property="obfuscation.up-to-date" targetfile="${obfuscator.destjar}">
            <srcfiles dir="${buildsystem.baton}"/>
        </uptodate>
    </target>
    <target name="skip-obfuscation" depends="proguard-init" if="obfuscation.up-to-date">
        <fail unless="obfuscated.classes.dir">Must set obfuscated.classes.dir</fail>
        <nb-overrideproperty name="buildsystem.baton" value="${obfuscated.classes.dir}"/>
    </target>
    <target name="proguard" depends="skip-obfuscation" description="Obfuscate project classes." unless="no.obfusc">
        <fail unless="obfuscated.classes.dir">Must set obfuscated.classes.dir</fail>
        <fail unless="obfuscator.srcjar">Must set obfuscator.srcjar</fail>
        <fail unless="obfuscator.destjar">Must set obfuscator.destjar</fail>
        <property name="obfuscator.classpath" value=""/>
        <dirname file="${obfuscator.srcjar}" property="obfuscator.srcjar.dir"/>
        <dirname file="${obfuscator.destjar}" property="obfuscator.destjar.dir"/>
        <mkdir dir="${obfuscator.srcjar.dir}"/>
        <mkdir dir="${obfuscator.destjar.dir}"/>
        <jar jarfile="${obfuscator.srcjar}" basedir="${buildsystem.baton}"/>
        <property name="obfuscation.custom" value=""/>
        <nb-obfuscate srcjar="${obfuscator.srcjar}" destjar="${obfuscator.destjar}" obfuscatorclasspath="${obfuscator.classpath}" classpath="${platform.bootclasspath}:${extra.classpath}" obfuscationLevel="${obfuscation.level}" extraScript="${obfuscation.custom}"/>
        <mkdir dir="${obfuscated.classes.dir}"/>
        <unjar src="${obfuscator.destjar}" dest="${obfuscated.classes.dir}"/>
        <nb-overrideproperty name="buildsystem.baton" value="${obfuscated.classes.dir}"/>
    </target>
    
    <target name="pre-obfuscate"/>
    <target name="post-obfuscate"/>
    <target name="obfuscate" depends="compile,pre-obfuscate,proguard,post-obfuscate" description="Obfuscate project classes."/>
    
    <import file="lwuit.xml" optional="true"/>
    <target name="-lwuit-check">
        <condition property="lwuit.allowed">
            <and>
                <available file="nbproject/lwuit.xml"/>
                <isset property="is.mesdk_lwuit"/>
            </and>
        </condition>
    </target>
    <target name="-pre-lwuit-build" depends="-lwuit-check" if="lwuit.allowed"/>
    <target name="-lwuit-build" depends="-lwuit-check" if="lwuit.allowed">
        <antcall target="lwuit_build"/>
    </target>
    <target name="-post-lwuit-build" depends="-lwuit-check" if="lwuit.allowed"/>
    <target name="lwuit-build" depends="-lwuit-check,-pre-lwuit-build, -lwuit-build, -post-lwuit-build" if="lwuit.allowed"/>
    
    <target name="pre-preverify"/>
    <target name="do-preverify" if="cldc-platform.trigger">
        <fail unless="preverify.classes.dir">Must set preverify.classes.dir</fail>
        <mkdir dir="${preverify.sources.dir}"/>
        <copy todir="${preverify.sources.dir}">
            <fileset dir="${buildsystem.baton}" includes="**/*.class"/>
        </copy>
        <mkdir dir="${preverify.classes.dir}"/>
        <nb-preverify srcdir="${preverify.sources.dir}" destdir="${preverify.classes.dir}" classpath="${platform.bootclasspath}:${extra.classpath}" configuration="${platform.configuration}" platformhome="${platform.home}" platformtype="${platform.type}" commandline="${platform.preverifycommandline}"/>
        <copy todir="${preverify.classes.dir}">
            <fileset dir="${buildsystem.baton}" defaultexcludes="${filter.use.standard}" excludes="${filter.excludes.evaluated},${build.classes.excludes}"/>
        </copy>
        <nb-overrideproperty name="buildsystem.baton" value="${preverify.classes.dir}"/>
    </target>
    <target name="post-preverify"/>
    <target name="preverify" depends="obfuscate,lwuit-build,pre-preverify,do-preverify,post-preverify" description="Preverify project classes."/>
    
    <target name="set-password-init">
        <property name="sign.enabled" value="false"/>
        <condition property="skip-sign-keystore-password-input">
            <or>
                <isfalse value="${sign.enabled}"/>
                <and>
                    <isset property="sign.keystore"/>
                    <isset property="sign.keystore.password"/>
                    <not>
                        <equals arg1="${sign.keystore}" arg2="" trim="true"/>
                    </not>
                    <not>
                        <equals arg1="${sign.keystore.password}" arg2="" trim="true"/>
                    </not>
                </and>
            </or>
        </condition>
        <condition property="skip-sign-alias-password-input">
            <or>
                <isfalse value="${sign.enabled}"/>
                <and>
                    <isset property="sign.keystore"/>
                    <isset property="sign.alias"/>
                    <isset property="sign.alias.password"/>
                    <not>
                        <equals arg1="${sign.keystore}" arg2="" trim="true"/>
                    </not>
                    <not>
                        <equals arg1="${sign.alias}" arg2="" trim="true"/>
                    </not>
                    <not>
                        <equals arg1="${sign.alias.password}" arg2="" trim="true"/>
                    </not>
                </and>
            </or>
        </condition>
    </target>
    <target name="set-keystore-password" if="netbeans.home" unless="skip-sign-keystore-password-input">
        <nb-enter-password keystore="${sign.keystore}" passwordproperty="sign.keystore.password"/>
    </target>
    <target name="set-alias-password" if="netbeans.home" unless="skip-sign-alias-password-input">
        <nb-enter-password keystore="${sign.keystore}" keyalias="${sign.alias}" passwordproperty="sign.alias.password"/>
    </target>
    <target name="set-password" depends="set-password-init,set-keystore-password,set-alias-password"/>
    
    <target name="add-configuration" unless="contains.manifest.configuration">
        <nb-output file="${dist.dir}/${dist.jad}" encoding="UTF-8" append="true">MicroEdition-Configuration: ${platform.configuration}
</nb-output>
        <nb-output file="${manifest.build.file}" encoding="UTF-8" append="true">MicroEdition-Configuration: ${platform.configuration}
</nb-output>
    </target>
    <target name="add-profile" unless="contains.manifest.profile">
        <nb-output file="${dist.dir}/${dist.jad}" encoding="UTF-8" append="true">MicroEdition-Profile: ${platform.profile}
</nb-output>
        <nb-output file="${manifest.build.file}" encoding="UTF-8" append="true">MicroEdition-Profile: ${platform.profile}
</nb-output>
    </target>
    <target name="create-jad" if="cldc-platform.trigger">
        <fail unless="dist.jad">Must set dist.jad</fail>
        <mkdir dir="${build.dir}"/>
        <dirname file="${dist.dir}/${dist.jad}" property="dist.jad.dir"/>
        <mkdir dir="${dist.jad.dir}"/>
        <condition property="evaluated.manifest.apipermissions" value="${manifest.apipermissions}">
            <not>
                <equals arg1="${platform.profile}" arg2="MIDP-1.0"/>
            </not>
        </condition>
        <condition property="evaluated.manifest.pushregistry" value="${manifest.pushregistry}">
            <not>
                <equals arg1="${platform.profile}" arg2="MIDP-1.0"/>
            </not>
        </condition>
        <condition property="contains.manifest.configuration">
            <contains substring="MicroEdition-Configuration: " string="${manifest.others}"/>
        </condition>
        <condition property="contains.manifest.profile">
            <contains substring="MicroEdition-Profile: " string="${manifest.others}"/>
        </condition>
        <property value="" name="evaluated.manifest.apipermissions"/>
        <property value="" name="evaluated.manifest.pushregistry"/>
        <property name="manifest.jad" value=""/>
        <property name="manifest.manifest" value=""/>
        <nb-output file="${dist.dir}/${dist.jad}" encoding="UTF-8">${manifest.midlets}${evaluated.manifest.apipermissions}${evaluated.manifest.pushregistry}${manifest.others}${manifest.jad}</nb-output>
        <nb-output file="${manifest.build.file}" encoding="UTF-8">${manifest.midlets}${evaluated.manifest.apipermissions}${evaluated.manifest.pushregistry}${manifest.others}${manifest.manifest}</nb-output>
        <antcall target="add-configuration" inheritall="true" inheritrefs="true"/>
        <antcall target="add-profile" inheritall="true" inheritrefs="true"/>
        <property name="manifest.available" value="true"/>
    </target>
    
    <target name="do-extra-libs" if="extra.classpath">
        <property name="dist.lib.dir" value="${dist.dir}/lib"/>
        <mkdir dir="${dist.lib.dir}"/>
        <copy todir="${dist.lib.dir}">
            <path path="${extra.classpath}"/>
            <flattenmapper/>
        </copy>
    </target>
    
    <target name="nokiaS80-prepare-j9" if="nokiaS80-platform.trigger">
        <fail message="Main class is not set!">
            <condition>
                <equals arg1="${main.class}" arg2="" trim="true"/>
            </condition>
        </fail>
        <mkdir dir="${build.dir}/j9"/>
        <taskdef name="j9builder" classname="org.netbeans.modules.j2me.cdc.project.J9Builder" classpath="${libs.cdc-ant-utils.classpath}"/>
        <j9builder jvmargs="${run.jvmargs}" mainclass="${main.class}" args="${application.args}" home="${platform.home}" dist="${j9.dist}" id="NOKIA" platform="${platform.type}" xlet="${main.class.xlet}" applet="${main.class.applet}" jarname="${dist.jar}"/>
        <copy file="${manifest.file}" tofile="${manifest.build.file}" failonerror="false"/>
        <property name="manifest.available" value="true"/>
        <loadfile property="nokia.manifest.j9" srcFile="${j9.dist}"/>
    </target>
    <target name="nokiaS80-prepare-manifest" depends="nokiaS80-prepare-j9" if="nokiaS80-platform.trigger" unless="nokia.icon.invalid">
        <pathconvert property="logo.icon.name" pathsep=" ">
            <path path="${nokiaS80.application.icon}"/>
            <chainedmapper>
                <flattenmapper/>
                <globmapper from="*" to="*"/>
            </chainedmapper>


The error says class file is missing, you can try to clean and build.

First Backup fails with Error 11

Attempting my first backup to my new Western Digital 160GB MyBook, Time Machine exits with an error before finishing the backup. The console output is below:
Dec 25 14:05:05 Katana /System/Library/CoreServices/backupd[751]: Backup requested by user
Dec 25 14:05:05 Katana /System/Library/CoreServices/backupd[751]: Starting standard backup
Dec 25 14:05:05 Katana /System/Library/CoreServices/backupd[751]: Backing up to: /Volumes/Time Machine/Backups.backupdb
Dec 25 14:05:05 Katana /System/Library/CoreServices/backupd[751]: Ownership is disabled on the backup destination volume. Enabling.
Dec 25 14:05:05 Katana KernelEventAgent[35]: tid 00000000 received unknown event (256)
Dec 25 14:05:45 Katana /System/Library/CoreServices/backupd[751]: Backup content size: 37.5 GB excluded items size: 2.5 GB for volume Katana
Dec 25 14:05:45 Katana /System/Library/CoreServices/backupd[751]: No pre-backup thinning needed: 42.11 GB requested (including padding), 148.96 GB available
Dec 25 14:05:45 Katana /System/Library/CoreServices/backupd[751]: MDBackupBegin() returned result (909) > 0, waiting
Dec 25 14:06:15 Katana /System/Library/CoreServices/backupd[751]: Backup requested by automatic scheduler
Dec 25 14:09:22 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:09:22 Katana kernel[0]:
Dec 25 14:09:22 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/ko.lproj/iMovieHelp/gfx/frwr4004pn. gif to (null)
Dec 25 14:09:23 Katana kernel[0]:
Dec 25 14:09:45 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:09:45 Katana kernel[0]:
Dec 25 14:09:45: --- last message repeated 1 time ---
Dec 25 14:09:45 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/ko.lproj/iMovieHelp/gfx/frwr800.gif to (null)
Dec 25 14:10:10 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:10:10 Katana kernel[0]:
Dec 25 14:10:10 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/ptPT.lproj/iMovieHelp/sty/access3box.css to (null)
Dec 25 14:10:10 Katana kernel[0]:
Dec 25 14:10:34 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:10:34 Katana kernel[0]:
Dec 25 14:10:34: --- last message repeated 1 time ---
Dec 25 14:10:34 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/sv.lproj/iMovieHelp/gfx/accessborderinnertopright.gif to (null)
Dec 25 14:10:57 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:10:57 Katana kernel[0]:
Dec 25 14:10:57 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/sv.lproj/iMovieHelp/gfx/accessborderleft.gif to (null)
Dec 25 14:10:57 Katana kernel[0]:
Dec 25 14:11:20 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:11:20 Katana kernel[0]:
Dec 25 14:11:20: --- last message repeated 1 time ---
Dec 25 14:11:20 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/sv.lproj/iMovieHelp/sty/access_3box .css to (null)
Dec 25 14:11:43 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:11:43 Katana kernel[0]:
Dec 25 14:12:06: --- last message repeated 1 time ---
Dec 25 14:11:43 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/zhTW.lproj/iMovieHelp/gfx/borderright.gif to (null)
Dec 25 14:12:06 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:12:06 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/zhTW.lproj/iMovieHelp/gfx/bordertop.gif to (null)
Dec 25 14:12:06 Katana kernel[0]:
Dec 25 14:12:29: --- last message repeated 1 time ---
Dec 25 14:12:29 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:12:29 Katana kernel[0]:
Dec 25 14:12:29 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/zhTW.lproj/iMovieHelp/gfx/step2.gif to (null)
Dec 25 14:12:52 Katana kernel[0]:
Dec 25 14:12:52 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/zhTW.lproj/iMovieHelp/gfx/step3.gif to (null)
Dec 25 14:12:52 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:12:52 Katana kernel[0]:
Dec 25 14:13:16: --- last message repeated 1 time ---
Dec 25 14:13:16 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:13:16 Katana kernel[0]:
Dec 25 14:13:38: --- last message repeated 1 time ---
Dec 25 14:13:16 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/zh_TW.lproj/iMovieHelp/shrd/opnbnds ig.scpt to (null)
Dec 25 14:13:39 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:13:38 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Applications/iMovie.app/Contents/Resources/zh_TW.lproj/iMovieHelp/shrd/OpnFile .scpt to (null)
Dec 25 14:13:39 Katana kernel[0]:
Dec 25 14:14:09: --- last message repeated 1 time ---
Dec 25 14:20:22 Katana ntpd[26]: time reset -0.176119 s
Dec 25 14:27:34 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:27:34 Katana kernel[0]:
Dec 25 14:27:34 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Stepping Out Short.caf to (null)
Dec 25 14:27:34 Katana kernel[0]:
Dec 25 14:27:57 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:27:57 Katana kernel[0]:
Dec 25 14:27:57: --- last message repeated 1 time ---
Dec 25 14:27:57 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Strategy.caf to (null)
Dec 25 14:28:19 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:28:19 Katana kernel[0]:
Dec 25 14:28:19 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Swing City Long.caf to (null)
Dec 25 14:28:19 Katana kernel[0]:
Dec 25 14:28:42 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:28:42 Katana kernel[0]:
Dec 25 14:29:05: --- last message repeated 1 time ---
Dec 25 14:28:42 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Swing City Medium.caf to (null)
Dec 25 14:29:05 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:29:05 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Swing City Short.caf to (null)
Dec 25 14:29:05 Katana kernel[0]:
Dec 25 14:29:27: --- last message repeated 1 time ---
Dec 25 14:29:27 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:29:27 Katana kernel[0]:
Dec 25 14:29:27: --- last message repeated 1 time ---
Dec 25 14:29:27 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Tennessee Twister Long.caf to (null)
Dec 25 14:29:50 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:29:50 Katana kernel[0]:
Dec 25 14:29:50 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Tennessee Twister Medium.caf to (null)
Dec 25 14:29:50 Katana kernel[0]:
Dec 25 14:30:13 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:30:13 Katana kernel[0]:
Dec 25 14:30:13: --- last message repeated 1 time ---
Dec 25 14:30:13 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Tennessee Twister Short.caf to (null)
Dec 25 14:30:58 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:30:58 Katana /System/Library/CoreServices/backupd[751]: Canceling backup.
Dec 25 14:30:58 Katana kernel[0]:
Dec 25 14:30:58 Katana /System/Library/CoreServices/backupd[751]: Error: (-36) copying /Library/Audio/Apple Loops/Apple/iLife Sound Effects/Jingles/Three Pointer Long.caf to (null)
Dec 25 14:30:58 Katana kernel[0]:
Dec 25 14:30:58 Katana kernel[0]: disk0s2: 0xe0030005 (UNDEFINED).
Dec 25 14:30:58 Katana kernel[0]:
Dec 25 14:30:58: --- last message repeated 1 time ---
Dec 25 14:30:58 Katana /System/Library/CoreServices/backupd[751]: Copied 27519 files (5.5 GB) from volume Katana.
Dec 25 14:30:58 Katana /System/Library/CoreServices/backupd[751]: Copy stage failed with error:11
Dec 25 14:30:58 Katana /System/Library/CoreServices/backupd[751]: Backup failed with error: 11
Anyone have any idea what this error means, or how to fix it?

Check the formatting and partitioning for your Time Machine disk. Launch Disk Utility from the dock or from the Applications > Utilities folder. Click on the upper icon for your Time Machine disk in the left window and the partition type will show on the bottom of the Disk Utility window. It should be GUID for Intel Macs and Apple Partition Map for PPC Macs.
Click on the indented icon below the upper Time Machine disk icon. That will show the formatting. It should be Mac OS Extended (Journaled). If the formatting and/or partitioning is not correct, reformat following the directions in this article.

[USF-XSim-62] 'elaborate' step failed with error(s) at vivado 2015.2 Behavioural Simulation

[USF-XSim-62] 'elaborate' step failed with error(s). Please check the Tcl console output or 'C:/xx/axi_pci/axi_pci.sim/sim_1/synth/func/elaborate.log' file for more information.

As stated above, please provide more information if you need any inputs from our end. As it is Vivado Simulator, you can also refer to the Messages tab and see what is the error. Most of the time if elaboration fails then it is possible that some modules were missing or the component/entity binding has failed or the compilation order is not proper. You can also refer to the compile.log to see if there are any warnings. All the logs can be found in the sim_1/behav folder.

EvtFormatMessage function fails with error code 15033 (ERROR_EVT_MESSAGE_LOCALE_NOT_FOUND) on non-English Windows OS

I have an App which subscribes to Windows events and if it is matching the filter criteria, it reports it.
I have observed a strange problem on non-English windows 2008 OS.
If the Windows event is of source = EventLog (e.g. Event ID 1102: Security log was cleared), then EvtFormatMessage fails with error code 15033. But if the event is of any other source (e.g. Microsoft Security Auditing), then it works absolutely fine.
While calling EvtOpenPublisherMetadata, I have created locale ID as MAKELCID(MAKELANGID(0x09,0x01) i.e. Primary language = LANG_ENGLISH and Sub Language = SUBLANG_DEFAULT.
I want events details in English only and hence primary language is put as English. If I change this macro to have primary language as LANG_CHINESE and sub language as SUBLANG_CHINESE_SIMPLIFIED, then it works fine but gives back event details in native
OS language (Chinese in this case). That's not a desirable output for me.
Following is the way I'm calling EvtFormatMessage
EvtFormatMessage(hMetaData, hEvent[0], -1, 0, NULL,
1 /* EvtFormatMessageEvent */,
m_pTextBufferSize/sizeof(WCHAR),
m_pTextBuffer, &dwBuffUsed);
A work-around for this is to install a MUI pack for English language. If the MUI pack is installed then it works fine. But I cannot enforce users to have this pack installed on all their systems.
My question is why this API is working for some set of Events whereas failing for some specific Events? Am I doing something wrong?
Any help would be appreciated.
TIA,
Regards,
Yogesh

Was on vacation and hence the delay in replying.
As mentioned earlier, while calling EvtOpenPublisherMetadata, I have created locale ID as MAKELCID(MAKELANGID(0x09,0x01)
i.e. Primary language = LANG_ENGLISH and Sub Language = SUBLANG_DEFAULT. If I change this macro
to have primary language as LANG_CHINESE and sub language as SUBLANG_CHINESE_SIMPLIFIED, then it works fine but gives back event details in native OS language (Chinese in this case).
This is not an option for me as I want event details in English language only.
Regards,
Yogesh
Regards, Yogesh

SSIS custom execute sql task : Failed with error

I am developing a custom SSIS task for running sql task. But it fails with error - I'm trying to set the resultsetbinding to be used by next task in workflow.
Error: 0xC0014054 at CustomSSISTask: Failed to lock variable "User::id" for read access with error 0xC0010001 "The variable cannot be found. This occurs when an attempt is made to retrieve a variable from the Variables collection on a container
during execution of the package, and the variable is not there. The variable name may have changed or the variable is not being created.".
Error: 0xC002F210 at CustomSSISTask, Execute SQL Task: Executing the query "SELECT id FROM sysobjects WHERE name = 'sysrowsets..." failed with the following error: "Failed to lock variable "User::id" for read access with error 0xC0010001
"The variable cannot be found. This occurs when an attempt is made to retrieve a variable from the Variables collection on a container during execution of the package, and the variable is not there. The variable name may have changed or the variable is
not being created.".
". Possible failure reasons: Problems with the query, "ResultSet" property not set correctly, parameters not set correctly, or connection not established correctly.
Warning: 0x80019002 at CustomSSISTask: SSIS Warning Code DTS_W_MAXIMUMERRORCOUNTREACHED. The Execution method succeeded, but the number of errors raised (3) reached the maximum allowed (1); resulting in failure. This occurs when the number of errors reaches
the number specified in MaximumErrorCount. Change the MaximumErrorCount or fix the errors.
Task failed: CustomSSISTask
Here is the code sample I'm trying ,
public override DTSExecResult Execute(Connections connections, VariableDispenser variableDispenser,
IDTSComponentEvents componentEvents, IDTSLogging log, object transaction)
MessageBox.Show("testing:");
try
// Add the SQL Task
Package package = new Package();
package.Executables.Add("STOCK:SQLTask");
Microsoft.SqlServer.Dts.Runtime.Variable variable = package.Variables.Add("id", false, "User", 0);
// Get the task host wrapper
TaskHost taskHost = package.Executables[0] as TaskHost;
// Get the task object
ExecuteSQLTask task = taskHost.InnerObject as ExecuteSQLTask;
// Set core properties
task.Connection = connections[0].Name;
task.SqlStatementSource = "SELECT id FROM sysobjects WHERE name = 'sysrowsets'";
//task.SqlStatementSource =
// "SELECT PersonID from [AmalgaSpeedTableData].[SpeedTable].[DimPerson] where PersonIntID = '1'";
task.SqlStatementSourceType = SqlStatementSourceType.DirectInput;
// Add result set binding, map the id column to variable
IDTSResultBinding resultBinding = task.ResultSetBindings.Add();
//IDTSResultBinding resultBinding = task.ResultSetBindings.GetBinding(0);
resultBinding.ResultName = "variable";
resultBinding.DtsVariableName = variable.QualifiedName; //"User::id";
task.Execute(connections, variableDispenser, componentEvents, log, transaction);
catch (Exception ex)
throw new ArgumentException(ex.Message);
return DTSExecResult.Success;
It doesnt throw any exception but custom task fails.
Later I will be also using parametersetbindings to pass some input parameters to this task , since I'm stuck for out param - blocked moving ahead.
Any help would be greatly appreciated.
Thanks
Sang

Hi, could you check whether the following threads help:
http://stackoverflow.com/questions/5787621/ssis-package-failed-to-locak-variable-for-read-access-with-error-0xc0010001
http://social.msdn.microsoft.com/Forums/sqlserver/en-US/40ee7eff-5ec1-426f-a1a8-ab85b40b51aa/error-variable-can-not-be-found-while-executing-package-from-the-net-code?forum=sqlintegrationservices
Regards, Leo

Help !!! Re: Fianacial Analytics failed with Error Code = 36331

I am getting an error exactly reported under another Post 'Re: Fianacial Analytics failed with Error Code = 36331'
workflow log shows DB error to OLTP database..
ERROR : LM_36488 [Wed Aug 19 15:05:52 2009] : (5928|2384) Session task instance [SDE_ORA_GLJournals_Full] : [TM_6193 An error occurred while expanding the connection parameter [Database connection name ORA_R12 for database connection variable $DBConnection_OLTP is not well defined.
Can someone point to where the probem is
I have Physical datasource definition of OLTP Warehouse -> Test Connection works fine -->

I am unit Testing the activity SDE_ORA_GLJournals under Execution Plan, i can see an error.
ANOMALY INFO::: Error while executing : INFORMATICA TASK:SDE_ORAR12_Adaptor:SDE_ORA_GLJournals_Full:(Source : FULL Target : FULL)
          MESSAGE:::
          Irrecoverable Error
          Error while contacting Informatica server for getting workflow status for SDE_ORA_GLJournals_Full
          Error Code = 36331:Unknown reason for error code 36331
          Pmcmd output :
any ideas
girish

[DC2] An net use or LsaPolicy operation failed with error 67 - Moving AD from 2003R2 to Server 2012

Hello, i hope someone can help me with this tricky situation.
The plan is to move AD from 2003R2 name "DC" to a server 2012 "DC2"
I have made all the adjustments and transferred all the role to the new 2012 server, and both are now GC servers.
The problem is "transferring" the netlogon share.
in DCDIAg on the new server i get:
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
Home Server = DC2
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\DC2
Starting test: Connectivity
......................... DC2 passed test Connectivity
Doing primary tests
Testing server: Default-First-Site-Name\DC2
Starting test: Advertising
......................... DC2 passed test Advertising
Starting test: FrsEvent
There are warning or error events within the last 24 hours after the
SYSVOL has been shared. Failing SYSVOL replication problems may cause
Group Policy problems.
......................... DC2 passed test FrsEvent
Starting test: DFSREvent
......................... DC2 passed test DFSREvent
Starting test: SysVolCheck
......................... DC2 passed test SysVolCheck
Starting test: KccEvent
......................... DC2 passed test KccEvent
Starting test: KnowsOfRoleHolders
......................... DC2 passed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... DC2 passed test MachineAccount
Starting test: NCSecDesc
......................... DC2 passed test NCSecDesc
Starting test: NetLogons
Unable to connect to the NETLOGON share! (\\DC2\netlogon)
[DC2] An net use or LsaPolicy operation failed with error 67,
The network name cannot be found..
......................... DC2 failed test NetLogons
Starting test: ObjectsReplicated
......................... DC2 passed test ObjectsReplicated
Starting test: Replications
......................... DC2 passed test Replications
Starting test: RidManager
......................... DC2 passed test RidManager
Starting test: Services
NtFrs Service is stopped on [DC2]
......................... DC2 failed test Services
Starting test: SystemLog
......................... DC2 passed test SystemLog
Starting test: VerifyReferences
......................... DC2 passed test VerifyReferences
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test
CrossRefValidation
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test
CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running partition tests on : dom1
Starting test: CheckSDRefDom
......................... domain passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... domain passed test CrossRefValidation
Running enterprise tests on : domain.xxxxx.no
Starting test: LocatorCheck
......................... domain.xxxxx.no passed test LocatorCheck
Starting test: Intersite
......................... domain.xxxx.no passed test Intersite
I have as a last option the burflags issue, i tried this with the option D2, but i think i have done it wrong, because the netlogon share is gone on the old DC. i took a backup of the files and folders before
i did this. http://support.microsoft.com/kb/290762/en-us But i am a little confused on which server i am going to set the D4 value on now? COuld someone help? Best regards Aksel

Hello Dirk
And thank you for your answer, in regards of the KB, do i have to follow the steps regarding:
Global vs. replica set specific reinitialization
You can locate the replica set specific
BurFlags
registry key by determining the GUID for the replica set that you want to configure. To determine which GUID
corresponds to which replica set and configure a restore, follow these steps:
Click Start, and then click Run.
In the Open box, type cmd and then press ENTER.
In the Command box, type net stop ntfrs.
Click Start, and then click Run.
In the Open box, type regedit and then press ENTER.
To determine the GUID that represents the replica set that you want to configure, follow these steps:
Locate the following key in the registry:
KEY_LOCAL_MACHINE\System\CurrentControlSet\Services\NtFrs\Parameters\Replica Sets
Below the Replica Sets subkey, there are one or more subkeys that are identified by a GUID. In the left pane, click the GUID, and then in the right
pane note the Data that is listed for the Replica Set Root value. This file system path will indicate which replica set is represented by this GUID.
Repeat step 4 for each GUID that is listed below the Replica Sets
And so on?
I have only thos 2 DC's in the network...

_Media creation failed with error message: 'The system cannot find the path specified.'

SCCM 2012 R2 CU2 all latest patches.
I attempted to create a task sequence media and I get the error in the screenshot below. I have deleted and recreated the operating system,boot image, driver pack and task sequence. The usb media is 16GB and the task sequence size is 3004MB.
I only see the error in CreateTSMedia.log as below. How do you fix this?
<![LOG[Beginning media generation]LOG]!><time="12:37:44.522+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="mediagenerator.cpp:418">
<![LOG[Partition activated]LOG]!><time="12:37:47.720+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="diskvolume.cpp:849">
<![LOG[Finished formatting volume F:\]LOG]!><time="12:37:55.723+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="imagewriter.cpp:772">
<![LOG[Assigning staging directory to F:\]LOG]!><time="12:37:55.724+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="imagewriter.cpp:1122">
<![LOG[===========================================]LOG]!><time="12:37:56.257+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="mediagenerator.cpp:476">
<![LOG[ Beginning pass to compute volume layout]LOG]!><time="12:37:56.257+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="mediagenerator.cpp:479">
<![LOG[===========================================]LOG]!><time="12:37:56.257+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="mediagenerator.cpp:487">
<![LOG[Setting up new volume]LOG]!><time="12:37:56.257+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="mediagenerator.cpp:1297">
<![LOG[WriteVolumeId()]LOG]!><time="12:37:56.257+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="mediagenerator.cpp:1038">
<![LOG[Failed to create media (0x80070003)]LOG]!><time="12:38:04.925+240" date="06-17-2014" component="CreateTsMedia" context="" type="3" thread="4668" file="createtsmedia.cpp:345">
<![LOG[CreateTsMedia failed with error 0x80070003, details='']LOG]!><time="12:38:04.925+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="createtsmedia.cpp:355">
<![LOG[MediaGenerator::~MediaGenerator()]LOG]!><time="12:38:04.925+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4668" file="mediagenerator.cpp:396">
<![LOG[Media creation process that was started from Admin Console completed.
]LOG]!><time="12:38:05.182+240" date="06-17-2014" component="CreateTsMedia" context="" type="1" thread="4772" file="createmedia.cpp:1065">
<![LOG[CreateMedia.exe finished with error code 80070003]LOG]!><time="12:38:05.182+240" date="06-17-2014" component="CreateTsMedia" context="" type="2" thread="4772" file="createmedia.cpp:1123">

Hi,
Error code 0x80070003 = "The system cannot find the path specified."
Have you checked the log file smsAdminUI.log? Maybe it can give us some clues.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Partition failed with error input output

Similar Messages

Maybe you are looking for