Partition map check failed because no slices were found for WD My Book 1140 media

Have been using a WD My Book 3TB HD which was partitioned into three 1TB partitions for almost a year. Now when I try to access it via my MacBook Pro I am getting the following error message "Problems were found with the partition map which might prevent booting; Error: Partition map check failed because no slices were found". Does anybody have any suggestions on how to repair this problem and salvage information stored on it?

I am also experiencing this problem.
4TB Hitachi Deskstar. Internal. Disk not readable error on boot.
"Partition map check failed becuase no slices were found" error when I attempt to verify or repair with Disk Utility.

Similar Messages

Seagate external drive: Partition map check failed because no slices were found

I have a 3TB Seagate Expansion external backup drive connected to my Retina Macbook Pro via USB. The disk will not eject from a regular Finder window - it will only eject from Disk Utility. Backups seem to otherwise be running fine. I tried to verify/repair the disk in Disk Utility, and I got the following error: "Partition map check failed because no slices were found." I am able to verify/repair the partition without any problem, and no errors are found.
I'm concerned about relying on a backup drive that may be heading south. Here is the output from diskutil info:
diskutil info disk3
   Device Identifier:        disk3
   Device Node:              /dev/disk3
   Part of Whole:            disk3
   Device / Media Name:      Seagate Expansion Desk Media
   Volume Name:              Not applicable (no file system)
   Mounted:                  Not applicable (no file system)
   File System:              None
   Content (IOContent):      GUID_partition_scheme
   OS Can Be Installed:      No
   Media Type:               Generic
   Protocol:                 USB
   SMART Status:             Not Supported
   Total Size:               3.0 TB (3000592977920 Bytes) (exactly 5860533160 512-Byte-Units)
   Volume Free Space:        Not applicable (no file system)
   Device Block Size:        4096 Bytes
   Read-Only Media:          No
   Read-Only Volume:         Not applicable (no file system)
   Ejectable:                Yes
   Whole:                    Yes
   Internal:                 No
   OS 9 Drivers:             No
   Low Level Format:         Not supported

@ Allan Eckert: Unfortunately, reformatting is out of the question, I have 5 years of work on this!
@ Loner T: Yes, the firmware did successfully upgrade after router reboot and a bit of troubleshoot.
Thanks for the quick replies. Keep 'em coming!

External drive error, does not mount: "Partition map check failed because no slices were found"

Hardware: MacBook late 2009 (2.26Ghz Core 2 Duo 2 GB RAM 250GB HDD) running 10.9.4, Hackintosh MacPro (3.29Ghz i3 16GB RAM 1TB HDD) running 10.9.4, external 3 TB Seagate Backup+ drive
As you can can see from the screenshot below,
The external drive was initially plugged in a Netgear WNDR4500 router by USB to be used as NAS. I was in the middle of updating the firmware when there was a power outage. Upon reboot, the drive no longer mounts, whatever it is plugged in (router, Mac, PC, etc.).
I ran DiskUtility on the partition map and volume, same errors. Here's an what I see:
As you can see above, the "Mount" icon is greyed out and I get the error message "Partition map check failed because no slices were found". If I select "the Archive" partition, the "Mount" icon is not greyed out but clicking it doesn't do anything. My HDD is basically unreadable.
I issued a few Terminal commands to see what was the problem, here are the results:
What can I do?
Currently running analysis on TestDisk and it is 50% after 48hrs. Need some help!

@ Allan Eckert: Unfortunately, reformatting is out of the question, I have 5 years of work on this!
@ Loner T: Yes, the firmware did successfully upgrade after router reboot and a bit of troubleshoot.
Thanks for the quick replies. Keep 'em coming!

Disk Utility - Partition map needs repair because a data partition needs loader space.

I just finished setting up both my OSX and Windows installs from scratch after fitting an SSD, which in-turn was right before my logic board died and Apple replaced it, now it looks like I have some sort of hard drive issue brewing.
This was my plan for the SSD, and how it currently displays in Disk Utility although that wasn't the case earlier:
And in Terminal:
My intention was to have two boot partitions for each OS, 'Macintosh HD' and 'Win 7 Pro' and a third shared data partition 'Projects' on the SSD, which I made in Drive Genius after installing Boot Camp. I don't want Macintosh HD accessible from Windows because I'll be using Paragon HFS+ or MacDrive to give write access and don't want OSs stomping on other OSs turf, hence needing three partitions. Everything looked fine until I just checked Disk Management under windows and realised it couldn't see the Projects volume. Even though it's fine in OS X, it was just marked black/unallocated space.
So I booted back into OSX, all my files look fine so I ran Disk Utility and the Partition tab looked really odd - unfortunately I didn't get a screenshot. All volumes reported their size correctly but visually, Macintosh HD took up most of the drive. I could see 'Windows 7 Pro' under this, but the Partition Layout section had a scrollbar, which if I scrolled down showed 'Projects' squished into a tiny gap at the bottom. I ran a Verify, which reported no problems, and at some time since the Partition Layout has reverted to how it should look (as in the screenshot above), with 'Projects' book-ended by "Macintosh HD' and 'Windows 7 Pro'.
Now when I run a Verify on Macintosh HD or Projects volumes, it says there's no problem, but if I run one on the drive, I get this message:
Volume Macintosh HD on disk0s2 has 0 bytes of trailing loader space and it needs 134217728 bytes
Problems were found with the partition map which might prevent booting
Error: Partition map needs repair because a data partition needs loader space.
I've only managed to find one other mention of this error here, but the fix is not relevant to me because I don't have Sophos installed. I've tried Single User/Safe Mode but it just boots into normal mode, so I can't do a fsck -fy.
** /dev/rdisk0s2 (NO WRITE)
Can't open /dev/rdisk0s2: Permission denied
That value in bytes is exactly 128mb, so I suspect the problem lies with one of the invisible partitions that show up in iPartition and Disk Management under Windows, but not in Disk Utility. I have backups and I suspect the root of the problem is partitioning in iPartition after installing Boot Camp, but I've never had issues with this approach in the past so I'm wary of just giving up and reinstalling Windows again will be massive hassle because I no longer have a SuperDrive and last time it refused to install from USB.
Anyone have any idea what's going on? It seems like the sort of issue Disk Utility should just handle, at least in Recovery mode, but it's not playing ball. It also doesn't seem like a massive problem since my files all look fine and performance is OK, so I'm reluctant to do anything major.
I'll update with a shot of the drive in Disk Management from Windows in a few minutes, in case that sheds light on anything. Thanks!

Similar issue here. I manually partitioned my hard disk for triple boot (using Gparted on Linux), then everything was just fine until I ran bootcamp, to do something as simple as create a boot USB.
I get the same error as a result and have to work my way into booting, by resorting first to a Linux live USB, then restarting from the live USB, to finally reach my rEFInd boot manager, or whichever boot manager should be initialized at startup.
I suppose that the cause in my case is that some operation "scratched" the protective MBR. See this:
http://www.mactech.com/articles/mactech/Vol.23/23.03/APMtoGPT/index.html
I am hoping to fix it using an external Yosemite installation media: see this guide -
http://www.macworld.com/article/2367748/how-to-make-a-bootable-os-x-10-10-yosemi te-install-drive.html
And as a last resort to reinstall.
I'll admit I am negatively surprised. I need this computer for professional reasons, and for the sake of "preserving the integrity of OSX", measures defined by Apple instead tend to make partitions far easier to damage. And this problem seems to affect a number of users.
As for what I have to go through to fix it: a 5GB download, during which I have to register my credit card to the Apple Store. "Pay first, get your free software next."
IF Disk Utility can fix it, from the external media, then fair enough. The hassle is unpleasant but it files as "a choice".
Otherwise you can file it safely under software design calamity.

Memory gates checking failed because the free memory is less than 5% of total memory

·         Business
Goal: Achieve a stable environment
·         Repro
Steps: n/a
·         Expected
Results: I expect the MSCRM Async services to use a relatively static amount of RAM
·         Actual
Results: Over the weekend, the memory hit critical mass and CRM failed
·         Environment:
Windows Server 2008, SQL Server 2008, CRM 2013 On Premise - both on the same box, Email Router is installed on the same box. We have not yet applied either of the two new UR for 2013.
I'm currently experiencing a memory leak in our production environment. I will fill out the details shortly.
Here's the error:
Log Name:      Application
Source:        System.ServiceModel 4.0.0.0
Date:          4/20/2014 11:39:14 PM
Event ID:      3
Task Category: WebHost
Level:         Error
Keywords:      Classic
User:          NETWORK SERVICE
Computer: server.domain.com
Description:
WebHost failed to process a request.
Sender Information: System.ServiceModel.ServiceHostingEnvironment+HostingManager/58366981
Exception: System.ServiceModel.ServiceActivationException: The service '/VisualWorkplace/XRMServices/2011/Organization.svc' cannot be activated due to an exception during compilation.
The exception message is:Memory gates checking failed because the free memory (1240145920 bytes) is less than
5% of total memory. As a result, the service will not be available for incoming requests. To resolve this, either reduce the load on the machine or adjust the value of minFreeMemoryPercentageToActivateService on the serviceHostingEnvironment config
element.. ---> System.InsufficientMemoryException: Memory gates checking failed because the free memory (1240145920 bytes) is less than 5% of total memory. As a result, the service will not be available for incoming requests. To resolve
this, either reduce the load on the machine or adjust the value of minFreeMemoryPercentageToActivateService on the serviceHostingEnvironment config element.
   at System.ServiceModel.Activation.ServiceMemoryGates.Check(Int32 minFreeMemoryPercentage, Boolean throwOnLowMemory, UInt64& availableMemoryBytes)
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.CheckMemoryCloseIdleServices(EventTraceActivity eventTraceActivity)
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath, EventTraceActivity eventTraceActivity)
We just recently increased the available memory from 8GB to 24GB to help ensure that there is enough memory. This error never happened on CRM v4. According to the resource monitor, SQL is only reserving 20.7GB of RAM and there is 694MB of RAM in Standby.
The main Async service is using 660MB and the maintenance Async service is using 265MB.
To resolve the issue temporarily, I restarted both Async services this morning. Shortly after everything came back, they were holding fairly steady around 350MB and 200MB. It's been six hours since then.
The last time I spoke with Microsoft about a similar problem, they suggested increasing the amount of RAM.

It became more and more of a problem. It was impacting the users in a more subtle way at first. You couldn't configure the CRM for Outlook client. After a while, they couldn't use CRM in Outlook at all and users reporting not being able to complete phone
call activities. I opened a ticket with MS and they suggested the same as Wilson Lou did. The organization error had nothing to do with the creep on the async services usage of RAM. It was indeed caused by SQL stealing all of the memory. Limiting the max usage
to 24GB RAM has resolved that error.
My Async processes are still using a LOT of RAM, but now that I have more than enough RAM, it doesn't seem to be a problem anymore. They are currently using about 700MB RAM each.
Also, I have upgraded to SP1, UR2.
Eric Hula - CRM Administrator

My time machine 3 TB HD was encryption enabled and it took forever. I tried reformattiing, it is online, but, get this Partition map repair failed while adjusting structures to fit current whole disk size. Any comments appreciated.

My time machine 3 TB HD was encryption enabled and it took forever. I tried reformattiing, it is online, but, get this Partition map repair failed while adjusting structures to fit current whole disk size. Any comments appreciated.

This issue has been in discussion (actively) since last August here:
https://discussions.apple.com/thread/4218970?start=0&tstart=0
After months and months of new reports, it's pretty clear that this is an Apple Mountain Lion problem and one that Apple needs to address. As one frsutrated user noted :
>>There is no consistent solution for a user. Apple has to supply it. All you can do is submit a bug report to
>> http://www.apple.com/feedback
Please, if you are encountering this problem you will save yourself a lot of wasted time and energey simple by joining me and others in asking Apple to fix this problem: Make a bug report.
Thanks!

Disk utility gives "Error: Partition map repair failed while adjusting structures to fit current whole disk size"

I am getting the following error when running Disk Utility (under ML) on an exteral USB hard drive:
Error: Partition map repair failed while adjusting structures to fit current whole disk size.
I get thsi when I ask Disk Utility to "Repair Disk" at the top level of the disk hierarchy (i.e. not on one of the partitions within the disk but on the disk itself). I was not getting this error with Lion on the same disk before I upgraded from Lion to ML.
It seems like a bug in ML. I found websites where they suggest that you just run Lion's Disk Utility and it will show the disk to be fine.
Any thoughts?

So, I finally seemed to have resolved things with the Seagate 4TB Firewire external drive. If you Google about, you will find a thread on Seagate's own support forum that describes how to disable the sleep function on the drive. You CANNOT ALLOW THE DRIVE TO SLEEP WHILE CONNECTED TO YOUR MAC.
After a lot of reading, here's what I think is happening: the drive goes to sleep, after some period of inactivity, and when you shutdown your Mac, OS X tries to write something to the drive as part of the dismount / disconnect / shutdown process. That fails in some manner, leaving the drive 'corrupted' at the filesystem or partition level.
Then, on the next boot-up, Mountain Lion tells you that it cannot repair the drive and it mounts as read only. Your only fix at that point is to re-partition / re-format and start over (which is big fun with 3TB of data to copy back on to the drive).
If you prevent the drive from sleeping, whenever it's connected to the MacBook, then the above process doesn't occur and voila, the drive just works. So far, I haven't had any problems with about a week of starting / shutting down my MacBook connected to the offending drive (translation: I was going to return the drive, but the problem is clearly with Mac OS X Mountain Lion).

DISK UTILITY Error: Partition map repair failed...

Hi all,
I purchased a new SEAGATE BACKUP PLUS 3T USB3.0 drive - and formatted GUID 1 partition - then ran repair disk and it showed with = "Error: Partition map repair failed while adjusting structures to fit current whole disk size"
And I also tried 4 partitions but no help
And I also tried formatting same on older 10.6 mac with no errors - then came back to 10.8 and error shows there...
Can some folks please try this on there own setups to see how widespread this is...
Criteria...
1 - ML 10.8.2
2 - Large external drive 2T or greater
Q: Has anyone experienced this and has a possible solution?
Thanks

HI all,
This issue has been in discussion (actively) since last August here:
https://discussions.apple.com/thread/4218970?start=0&tstart=0
After months and months of new reports, it's pretty clear that this is an Apple Mountain Lion problem and one that Apple needs to address. As one frustrated user noted :
>>There is no consistent solution for a user. Apple has to supply it. All you can do is submit a bug report to
>> http://www.apple.com/feedback
Please, if you are encountering this problem you will save yourself a lot of wasted time and energy simply by joining me and others in asking Apple to fix this problem: Make a bug report.
Thanks!

CHANGE ASSISTANT : Failed. No Environments were found in the Environment

Hi all,
Iam trying to apply MP5 on HRMS 9.1 peopletools 8.52 in change assistant getting error as
*(Step 5) Discovering Hub Environments.*
Failed. No Environments were found in the Environment Management Hub.
Note: All agents should be running and sending pulses for all Application,
Batch, File and Web Servers for the environment before Change Assistant is started.
*(Step 6) Pinging Metalink*
Failed.
*(Step 7) Pinging Update Gateway*
Failed.
*[Mon Dec 10 20:04:29 IST 2012] End Validation*
Unsuccessful completion (3 Steps Failed). Click on View Log to see additional messages.
I have set crawl path correctly, ping is working fine , hub url is also showing agent , change asiistant RUNNING
pls help
thanx
Arvind

this is what the log file shows...
unable to find help with the post you hav directed Hakan.....
Help me...
[Tue Dec 11 12:02:53 IST 2012] Begin Validation
output written to: C:\Program Files\PeopleSoft\Change Assistant\validate\validate_2012_12_11_12_2.log
(Step 1) Creating a Summary of Your Environment
PS_HOME: F:\PS_HOME\
Output Directory: D:\change_assistant\output\
Staging Directory: D:\change_assistant\staging\
Path: C:\Program Files\PeopleSoft\Change Assistant\jre\bin;.;C:\Windows\Sun\Java\bin;C:\Windows\system32;C:\Windows;F:\PS_HOME\bin\client\winx86;C:\Program Files\PeopleSoft\Change Impact Analyzer\dll;D:\ORACLE\product\11.2.0\dbhome_1\bin;F:\ORACLE\product\11.2.0\dbhome_1\bin;F:\app\299025\product\11.2.0\dbhome_1\bin;D:\apps\299025\product\11.2.0\dbhome_1\bin;D:\app\299025\product\11.2.0\dbhome_1\bin;D:\Oracle_Home\product\11.2.0\dbhome_1\bin;C:\Program Files\CA\SC\CAWIN\;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\WindowsPowerShell\v1.0\;C:\Program Files\Intel\DMIX;C:\PROGRA~1\CA\SC\CAM\bin;C:\Program Files\CA\DSM\bin;C:\Program Files\TortoiseSVN\bin;F:\BEA_HOME\TUXEDO\tuxedo10gR3_VS2008\bin;F:\BEA_HOME\TUXEDO\tuxedo10gR3_VS2008\jre\bin\server;F:\BEA_HOME\TUXEDO\tuxedo10gR3_VS2008\jre\bin
CLASSPATH: C:\Program Files\PeopleSoft\Change Assistant\changeassistant.jar;C:\Program Files\PeopleSoft\Change Assistant\mx4j-jmx.jar;C:\Program Files\PeopleSoft\Change Assistant\xercesImpl.jar;C:\Program Files\PeopleSoft\Change Assistant\xml-apis.jar;C:\Program Files\PeopleSoft\Change Assistant\xalan_2_7_0.jar;C:\Program Files\PeopleSoft\Change Assistant\serializer.jar;C:\Program Files\PeopleSoft\Change Assistant\commons-logging-1.0.1.jar;C:\Program Files\PeopleSoft\Change Assistant\commons-httpclient-3.1.jar;C:\Program Files\PeopleSoft\Change Assistant\commons-net-ftp-2.0.jar;C:\Program Files\PeopleSoft\Change Assistant\commons-codec-1.2.jar;C:\Program Files\PeopleSoft\Change Assistant\xmldb-api-20021118.jar;C:\Program Files\PeopleSoft\Change Assistant\xmldb-common.jar;C:\Program Files\PeopleSoft\Change Assistant\xmldb-xupdate-20040205.jar;C:\Program Files\PeopleSoft\Change Assistant\xindice-1.1b5-dev.jar;C:\Program Files\PeopleSoft\Change Assistant\psemf.jar;C:\Program Files\PeopleSoft\Change Assistant\psjoa.jar;C:\Program Files\PeopleSoft\Change Assistant\AbsoluteLayout.jar;C:\Program Files\PeopleSoft\Change Assistant\log4j-1.2.8.jar;C:\Program Files\PeopleSoft\Change Assistant\jxl.jar;C:\Program Files\PeopleSoft\Change Assistant\commons-io-1.4.jar;C:\Program Files\PeopleSoft\Change Assistant\jewt4.jar;C:\Program Files\PeopleSoft\Change Assistant\share.jar;C:\Program Files\PeopleSoft\Change Assistant\j2ee.jar
Current Working Directory: C:\Program Files\PeopleSoft\Change Assistant
Done.
(Step 2) Validating your SQL Query Tools
Found Oracle SQL Query Tool at d:\miscc\Oracle_Home\product\11.2.0\dbhome_1\bin\sqlplus.exe
Done. 1 SQL Query Tool found.
(Step 3) Pinging Environment Management Hub
Pinging 172.17.108.118
thanx
Arvind.

Lync Topology fails with error (Mutliple Entries were found for type "ms_RTC-SIP-EdgeProxy")

Hello everyone,
After I have finished with Lync FE, Monitoring and Archiving, and WAC server I was going well with Edge server until I got to the point of publishing the topology with Edge Server.
First time publishing went well but I wanted to place the configured IP addresses in the Edge server IP topology with a different IPs and when I published i got the below error.
I tried looking in the trusted Services in Configuration OU using ADSI Edit but never was able to figure out how do I find the duplicated entries? I used also used Softerra LDAP adminsitrator and was able to find 5 values but not sure which one to delete
among them.
Could anyone advise where to look? I'm posting the error as well below
Error: Multiple Active Directory entries were found for type "ms-RTC-SIP-EdgeProxy" with ID "egelyncedge.domain.local".
▼ Details
└ Type: InvalidDataException
└ ▼ Stack Trace
└
at Microsoft.Rtc.Management.Deployment.AD.ADSessionExtension.FindUnique[TResult](ADSession session, QueryScope scope, ADObjectId containerId, QueryFilter filter, String name, Boolean throwOnMissing)
at Microsoft.Rtc.Management.Deployment.Core.CompatEdgeProxy.Remove(ADSession session, String edgeProxyFqdn)
at Microsoft.Rtc.Management.Deployment.Roles.AccessEdge.GlobalDeactivate(IService service)
at Microsoft.Rtc.Management.Internal.Utilities.LogWriter.InvokeAndLog[T](Action`1 action, T arg)
2/19/2014 12:25:28 PM
Error
└
Error: An error occurred: "System.IO.InvalidDataException" "Multiple Active Directory entries were found for type "ms-RTC-SIP-EdgeProxy" with ID "egelyncedge.domain.local"."
Mohammed JH

Hi,
Glad to hear you have solved the issue and shared the train of thought.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

No operand values were found for operand EQPRICEIN1

Hi,
I am getting following error while doing billing,
plz help....
No operand values were found for operand EQPRICEIN1
Message No. AJ013
Diagnosis
No operand value was found for operand EQPRICEIN1 for the period 30.04.2015 -- 31.05.2015.
Procedure
Assign a value to the operand in the conditions, rate category facts or installation facts.
(Note: Additional information regarding this error can be found in the details for this message.)

Hi Kailash,
You are getting this error because the billing schema is calling variant EQPRICEIN1 for a calculation purpose and it is not being found.
You need to check at the Installation where this operand is maintained (at the rate, rate category or Installation fact) and maintain a value for the period that is not being found. (30.04.2015 - 31.05.2015).
Billing after making this update should solve your problem.
Regards,
Monis Shakeel

Error message - "Overlapping validity areas were found for country BR"

Hi Experts,
For a certain output type Y953 (e.g. for the shipment 2002355665 related to the DN 3087912658), an error message "Overlapping validity areas were found for country BR" is coming in as error.
The error message is appearing during the idoc processing of the shipment.
This is an incident of Dangerous Goods.
I would like to know if it is technically / functionally possible to find out as to why exactly this mesage is coming and how can we rectify the problem.
From technical point of view we checked that this message was not being called in the SAP system but was dynamically called.
kindly let me know of any breakthrough as this issue is critical as dangerous goods are being transported without needed documents printed.
Thanks in advance.
RIttik

Check whether note 836139 helps you.
thanks
G. Lakshmipathi

No operand values were found for operand MET_KVAT2C

Hi,
I am getting following error while doing billing,
pls help....
No operand values were found for operand MET_KVAT2C
Message no. AJ013
Diagnosis
No operand value was found for operand MET_KVAT2C for the period 03.06.2009 -- 24.06.2009.
Procedure
Assign a value to the operand in the conditions, rate category facts or installation facts.
(Note: Additional information regarding this error can be found in the details for this message.)
Regards,
Chetan

Hi Rajesh,
I Checked the registers , there are 10 register of which 4 for demand.
Here DEMAND14 is used for taking the readings from the registers and then converting it to the normal operand
Below is the part of schema :
DEMAND09     01     MET_KVA          FACTOR100%          MET_KVAT2A
DEMAND14     01     MET_KVAT2A               MET_KVAT2A
DEMAND09     03     MET_KVA          FACTOR100%          MET_KVAT2C
DEMAND14     01     MET_KVAT2C               MET_KVAT2C
DEMAND09     03     MET_KVA          FACTOR100%          MET_KVAT2D
DEMAND14     01     MET_KVAT2D               MET_KVAT2D
DEMAND09     03     MET_KVA          FACTOR100%          MET_KVAT2B
DEMAND07     01     MET_KVAT2B     MET_KVAT2C          MAX_KVA2
DEMAND07     01     MAX_KVA2     MET_KVAT2D          MAX_KVA2
The meter reading results ar maintained. also i maintained MET_KVAT2C value at rate category level. in this case the system found the value but then it is not geting value for MAX_KVA2.
I suppose this value should be passed from meter reading.
Also can you pls tell me what is Assign a value to the operand in the conditions in the error.
Regards,
Chetan

EJB modules were found for this application

I'm deploy may application on weblogic server 10R3
myejb.jar file is deployed success
When I deployed mayapp.war, the following error occured.
*weblogic.deployment.EnvironmentException: [J2EE:160167]The module jvcwebapp.war in application jvcwebapp uses ejb-links but no EJB modules were found for this application.*
web.xml
<ejb-local-ref>
<ejb-ref-name>ejb/local/SessionEJB</ejb-ref-name>
<ejb-ref-type>Session</ejb-ref-type>
<local>model.SessionEJBLocal</local>
<ejb-link>SessionEJB</ejb-link>
</ejb-local-ref>
thanks
Thiensu2810

The module abc-ViewController-context-root in application abc_Project1_abc uses ejb-links but no EJB modules were found for this application
Is the application deployed as an EAR application with web and ejb modules? If not, deploy as an EAR application.

Wind Vista SP2. iTunes 10.6.3.25. I'm trying to Consildate my Music Library on this PC, and get the error: "Copying files failed, because you don't have permission to change your iTunes Media folder or a folder within it." My admin user has Full Control

Any suggestions would be greatly appreciated!

I did what you suggested on all three folders: The main Music folder on the Mac hard disk, on the iTunes folder on the external 160GB Hard drive which contains the current media content and on the new 2TB hard disk on which I created a new media folder. I selected permission for myself which were already read+write and chose the apply to enclosed items on all three folders. I then changed the permission for others to read+write and applied to enclose items also an all three folders.
But it didn't solve anything.
Here's what happens: I choose the new directory in iTunes preferences (the media folder on the 2TB disk) I then go to File > Library > Organize Library and then choose Consolidate files. A window pops up and says copying "filename" with a progression bar underneath but the filename never changes. Instead the beachball appears when the mouse pointer hoovers over iTunes. Upon pressing the iTunes icon in the Dock it says that iTunes is not responding. At this point there's 2 different ways:
A - If I then force quit iTunes the iTunes window disappears but the application does not close. When I want to eject the 2TB disk it says it's being used by another application. Only when I cut the power to the 2TB disk does iTunes fully close. A window then pops up and says that the drive was not put away properly etc.
B - if I cut the power to the drive without force quitting iTunes, a window appears with the said: "Copying failed because you don't have permissions to change iTunes media folders etc." iTunes remains open and fully functional.

Partition map check failed because no slices were found for WD My Book 1140 media

Similar Messages

Maybe you are looking for