Partner redetermination in transactions

Hi,
I'm trying to configure partner determination procedures for service transactions in order to allow redetermination of partners, but I hanen't been able to find a solution.
Let suppose I have transaction types Z001 and Z002
The parties involved are
Z001_001 for Z001
Z002_001, Z002_003, Z002_003 for Z002
Transaction of type Z002 is created as follow up from Z001
BP with partner function Z002_001 is generally copied from the preceeding document (so, from Z001_001); BPs with partner functions Z002_002 and Z002_003 are determined through the relationships of the BP with partner function Z002_001.
By the way, BP with partner function Z002_001 can change in transaction Z002 after it has been saved (because of the fact that some condition are changed in the meanwhile): this has been implemented through the use of a BAdI.
Is it possible, via customizing, to allow the redetermination of the BPs with partner functions Z002_002 and Z002_003 through the relationships of the new BP with partner function Z002_001?
Thanks in advance for your support,
Regards,
Andrea
Edited by: Andrea Ricci on Sep 24, 2010 9:56 AM

Hi,
Hope you have already
1) Set "Determination Time in Partner Determination" to value 0 (Recurring) in Partner determination procedure for partner functions Z002_002 and Z002_003 .
2) In configuration of access sequence for Z002_002 and Z002_003 , you choose the source as BP relationships (CRM_Partner_C) and in Details Of source Section, choose the partner function as "Z002_001"
If you are specifically looking at redetermination at a later point of time there are certain steps you need to follow for partner Redetermination. These are listed in the below thread
Partner Redetermination
Hope this helps.
Regards,
Raghu

Similar Messages

Partner redetermination in business transactions

Hello,
Is there a FM/method available to do a partner redetermination in a business transaction?
Thanks,
Fred

We use FM CRM_PARTNER_DETERMINATION_OW and CRM_ORDER_MAINTAIN to make the redetermination.

Sending mail to all partner function in transaction

Hi Folks,
Standard action and condition sends mail to only main partner function in transaction. But transaction could have more than one partners for same partner function. Can mail be sent to all partners in transaction by using standard action configuration?
Regards,
Nikhil

Hi Nikhil,
You can control this using CRM_ACTION_BADI.
Below the use of this BADI.
In partner-dependent actions, business partners that occur in several functions, only the main partner remains.
This can be useful, for example to avoid sending the same e-mail to the same business partner if there are several action definitions for different partner functions or function types.
However, if several different actions have been defined as partner- dependent, this effect may not be required.
In this case, the CRM_ACTION_BADI standard implementation can be deactivated. In this case, all partners from the transaction are considered during action determination.
If this is also not required, a new implementation can be created.
Hope this helps.
Cheers, Satish

Partner Redetermination through DETERMINATION_ADD_IN_2

Hi All,
I am facing a problem in re-determination of Partners. Here is the required functionality.
I have implemented my logic in DETERMINATION_ADD_IN_2(BADI COM_PARTNRER_BADI) to determine partners. BADI is working fine and determining partners as well.
Now, if I change any values like type, subtype in CRMD_ORDER the already determined partners need to be redetermined, since the partners will be extracted from a custom table.
Can any one suggest me is there anyway to achieve this functionality.

Partner redetermination cannot be done with this BADI. Need to perform Even handlers.

How to block a partner customer from transaction posting

Dear Experts,
Please suggest/advice how to block a partner customer from transaction posting,As we have two customer categories defined 1.Parent customer 2.Child customer.One parent customer has several child customers and they are assigned in partner function part of the child master record.We have defined the parent customers for reporting purpose only,not for any transactions to be done.
So please suggest how can we block those parent codes from being transacted directly.We wan them only for reporting purpose.
Can we do the restriction on account group level or we have to make a validation for this.
Please advice.
Regards
Partha

Dear Partha,
You need to Block customer against posting -> Transaction FD05 (you can choose foe selected company or for all)
You can block also directly the invoice/payment in the document
Or define some tolerance limits and system block automatically
Let me know if it is not clear
Thanks
Tarek

Partner redetermination in CRM for the replicated Sales contract from ECC

Hello Friends,
We are facing a typical issue, Our sales process is, we are creating Sales contract in ECC and replicating it in CRM. Problem area is we want to determine the Employee with the Territory ID in the CRM. Issue is the User will not be aware, who is the Employee responsible for the particular Sold to Party at the time of creation in ECC.
Config details:
1. Partner function related to Contracts are
    Sold to Party
    Ship to Party
    Bill to
    Payer
    Employee Responsible
    Employee _ Territory
2. Sales Contract is created in ECC and replicates in to CRM
3. Created Z partrner function for Employee_Territory and access seq assigned is 0030:Preeceding docyment>Territory>User
4. All the Partner function in ECC are determined through the Source as Sold to, except Employee_Terrritory, which is manual
5. Partner function value is manually maintained for Employee_territory in ECC sales contract
6. When replicated to CRM, I want this Employee_Territory to be redetermined based on the Territory attributes like Business partner Zip code
Kindly let me know, how to achieve it through configuration or if there is any BADI which requires minimum development.
Thanks,
Anup Bansal

Hey!
You can use badi COM_PARTNER_DETERM to determine partnter function based on Determination Sources.
You might also use user-defined callback function to realize your business requirement based on event handle technology.

Partner Determination using Transaction Type in Org Model

Hi Experts,
I am a functional consultant working on CRM 5.0 and currently customizing the partner determination procedure for transaction Lead. As per the business requirement, for all the leads created by default the system should determine a Lead Qualifier in the transaction Lead. In order to achieve this I am using rule 14000146 Orgman_14 which provides org unit for a transaction type. In the org model I am having a org unit defined as "Lead Management Dept" as well as I have created and assigned position Lead Qualifier and assigned emp to this position too. Now I have defined the sales attributes for this Org Unit "Lead Management Dept" and for the sales attribute "Transaction Type" filled in value as Y001 which is my transaction type for Lead.
The issue is that this defined attribute is not inherited by the position although this position is assigned to the above mentioned Org Unit and therefore the partner is not getting determined in the transaction. Can someone provide guidance about this issue? How to inherit this attribute to position so that the position is determined in the PDP? or any other alternative for this situation??
Thnaks and regards
Ambar Adhav

Hi,
Try transaction OOATTRCUST, scenario SALE> Attributes/Scenarios:
For PROC_TYPE attribute try to change the Inherit.Type and see how the system behaves.
Regards,
Susana Messias

[FSCM] partner assignment in transaction TS01

Hi, everyone
There is a tab 'Partner Assignment' to add another business partner related to a securities transaction in transaction TS01. But I cannot choose any business partner. I created brokers, issuers, depository bank, and counterparties in BP. And I assigned additional business partner role categories to TRG001 (financial transaction) work area and 200 (securities) application category. Here is the menu path in SPRO.
FSCM -> Treasury and Risk Management -> Basic Functions -> SAP Business Partner for Financial Services -> Settings for Financial Services -> Communication -> Settings for Partner-Object Relationship -> Assign Additional Business Partner Role Categories to Object
TR0150: Issuer
TR0152: Depository Bank
TR0801: Broker
But I cannot add any business partner to the partner list of 'Partner Assignment'.
Thanks.

Hi Minsun,
Can you help me on the issue you faced earlier for assignment of partner in TS01. I am also facing the same problem.
Please guide me for solving the issue since you already went through this.
Regards
Prasad AV

Determining Partner in Lead transaction thru Organisation model

Hello,
I need to determine responsible employee in lead transaction thru Organisation model that I have created . Now I dont want to use the attributes of the organisation as we have some constraints in that I need to determine a partner out of the assignment I have done in Organisation model. eg If BP "0001" is assigned to Org unit A as employee(Holder of a position) is it possible for me to determine the same employee in lead transaction as Employee responsible if I give the input of org unit A in the transaction? If yes pls let me know the steps for doing the same.
Thanking in anticipation.
Ambrish

In SPRO Customer Relationship Management > Master Data > Organizational Management > Organizational Data Determination >Wizard for Organizational Data Determination > Create Determination Rule of the Responsibility Type.
There, you assign a name, scenario (Sales or service) and select an attribute for example: SA_RESPORG Responsible organization, then assign Organization unit. After you assign profile to transaction type Lead.
Regards

Organization data determination based on custom partner entered in transactions

Hi Folks,
I want org data determination to happen based on a custom partner(say sales rep) entered in my transaction.Which rule is the closest so that I can apply the same.
Regards
Jaya

Hi Jaya
As your Business Partner is custom, then you'll need to create a custom Determination Rule anyway.
So in SPRO under Organizational Data Determination - Maintain Determination Rules.
Take a look at rule 10000280 - REG_SERV_04, it's probably still not a great fit, either way create the rule, copy the function module to a Z version and then adjust the code to incorporate the Sales Rep look-up.
Then you can assign the Rule to your own Organizational Data Determination Profile
Hope this helps get you started in the right direction.
Regards
Arden

Changing Sales Order PARTNER from 'MASS' transaction

Hi,
I have a requirement to change partner details (e.g. SHIP TO party from SH1 to SH2) for sales order. I need to use tcode 'MASS' (Mass maintainance) for BUS2032. But it does not have the option to change partner details.
Can anybody let me any approach to achieve this. If we can do it through a config or may be creating a custom business object etc...
I could found out the thread below talking about the same issue, but there is no solution to that. I want to build the solution around SAP standard and not interested for BDC/LSMW/CATT etc.
Mass changes Sales order partners
Thanks,
Madhu
Edited by: Madhu K on Nov 1, 2011 11:58 PM

Alan
I am ok to create a custom tcode for MASS. Do I need to copy the BUS2032 or the whole TCODE?
My major concern is, how to get the VBPA structure to the selection screen so that it ll show me the I/P fields to enter Old Ship to and New ship to..
Can You please give me some idea on this.
Thanks
Madhu

Adding Business partner in CRMD_ORDER transaction

hi ,
i would like to know whether any FM is available to add the partner in the transation CRMD_ORDER of the partner tab.
i need to add multiple Business partner thru my program.
i will be selecting the partner function as Contact person and will be adding the partner number.
ex: in the partner tab.
function                          partner
contact person                204
contact person                205
contact person                206
contact person                207
pls let me know.
thanks,
shantha sheela.

hi ,
i would like to know whether any FM is available to add the partner in the transation CRMD_ORDER of the partner tab.
i need to add multiple Business partner thru my program.
i will be selecting the partner function as Contact person and will be adding the partner number.
ex: in the partner tab.
function                          partner
contact person                204
contact person                205
contact person                206
contact person                207
pls let me know.
thanks,
shantha sheela.

Whats the use of PARTNER FUNCTIONS node in NACE transaction

hello
i would like to know when a output type is selected as medium EDI or ALE what needs to be entered in the PARTNER FUNCTIONS node and what is the main purpose of this node. Pls help
~Suresh

Hi Suresh,
Partner Functions Uses
You use partner functions in transactions, in all areas of partner processing and in some areas of business partner master data.
·        For example, you have a real estate business and define the function tenant to refer to your customers.
·        Tenant is then displayed in the header and Partner tab page in transactions, and on the Buying Center tab page, when relevant.
·        It appears in the Customizing settings for access sequences, partner determination procedures and partner teams
·        It appears in business partner master data when you assign partners to partner functions as part of maintaining sales area-specific data, and when you enter excluded partner functions.
Nace Transaction
The Tcode NACE is used to link the Standard SAP forms (SCRIPTFORM or SMARTFORM) or the customized form or the new form to its respective print programs. Also the output types, Form entry are linked with their forms and print programs. In short term, i can tell u that configuration or customization of forms to print programs, assigning output types, form entry to the forms are done using this Tcode.
NACE is used to create output type while creating the output type you will mention forms, and driver program.
that will be maintained in the table TNAPR.if you create the output type using NACE then it will be automatically visible in table NAST and TNAPR.
so check in NAST, TNAPR table
Reward if useful.
Thankyou,
Regards.

Go-live in EC-CS:update trading partner and transaction type on Balances

Hi collegues,
We are on a go-live this december for EC-CS (consolidation) but never have used trading partner nor consolidation transaction type so there are not GL account balances differenciated by these two items on our FMGLFLEXT database for the operative ledger.
Which is the best option for the data to be collected into our consolidation ledger in EC-CS (ECMCT database) when data transfer for all our consolidation units will be realtime update from FI?
I really don't know if I must correct the balance on FMGLFLEXT throught FI postings or if just adjustments on EC-CS it's the best option. I'm thinking on the posibility of extracting the Financial Statement at any time from F.01 tx...
Is there any transaction on FI to authomatically update at least the trading partner on GL accounts positions/balances?
Thanks in advance!
Regards,
Rushid

Hi David,
In fact there has never existed any entry for trading partners on GL, AR, AP master data. So consequenly, no balance in FAGLFLEXT/ nor documents on BSEG have ever had these fields populated.
My question is: which is the common option for a go live in such situation? Our users will distribute the current GL balances into "sub-balances" (GLAcctTxtypetradpartner) in an excell file but I do not really know what to do with this data:
- direct postings on BSEG cancelling the previous totals,
- rollup into a Special ledger of the new gl,
- rollup into the Preparations for Consolidation Ledger,
- corrections on ECMCT after the periodic extract...
What would choose?
Thanks!

Not all fields for Business partner are exported

Hello,
I am exporting Business partner data from CRM to another system, through XIF. I get on target system XML file with Business partner data. But I have only standart fields. I can't get fields, which was created my company for own use.
For example, for Business partner I have Business Agreement, but after export to XML, I have no Business agreement data in another system. But I have standart data, for example, Business partner Name, ID, ets.
Anybody know what I can do to export all the fields for Business partner? Some transaction or somthing else? Where can I customize output XML with Business partner data?
Best regarda,
Alexander.

Hi,
You have the right observation. There is no mandatory fields for BP. It means you can update any single field against CardCode. CardCode is the only mandatory field which is the only primary key must be unique.
Thanks,
Gordon

Partner redetermination in transactions

Similar Messages

Maybe you are looking for