Password check failed
Hello,
I've a problem with the message "enter current password" when starting notebook, but I don't know it!
The notebook is an HP Mini 110 - 1100sl
p/n: CNU9371X7X
Any solution?
Thanks for helping me!
This question was solved.
View Solution.
Hi,
Enter: e9lofx34x4 ( Note that in both cases, the 3rd character is a lower case L )
or
e9lofx3rxr
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience
Similar Messages
-
Password Check Failed, Fatal Error, System Halted, CNU949701P
Hello!
I have a HP netbook model Mini CQ 10, and I have not switched it on in a while.
I recently went to turn it on to recover some important documents and this error message shows up;
Password check failed
Fatal Error... System Halted
CNU949701P
Canu anyone PLEASE HELP ME! I would be so grateful!
Thank you!
x
This question was solved.
View Solution.Try >> e9lovox132
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
Password check failed fatal error system halted CNU9384PJY
BOOTING ENTER CURRENT PASSWORD THREE TIMES GOES TO PASSWORD CHECK FAILED FATAL ERROR SYSTEM HALTEDCNU9384PJY AFTER NETBOOK SET UP FOR A WHILE THANKS FOR ANY HELP
Enter: e9lofuv2wi ( 3rd character is a llower case L ) Regards, DP-K
-
Password check failed : CNU9273LZJ - need password pls
Need password for CNU9273LZJ
This question was solved.
View Solution.Axelin
Which password? - BIOS or Windows?
If BIOS admin password check failed, then try this:
e9lo7xfk0w
all are small letters
third letter is small case L
fourth letter is small case O
ninth character is number Zero
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP** -
Password check failed code 2MC9360C12
My HP Mini 110 suddenly says "Password check failed, Fatal Error......System Halted. 2MC9360C12"Can somebody help me?
Hi, Use the below code to reset the BIOS password 74eofg1e37 You can: 1. Use the unlock code you generated to enter the BIOS
2. Disable all passwords that are enabled in the BIOS's security menu.
3. If asked for current password - type the unlock code
4. For new password, just press ENTER key
5. Repeat the same for verify password column. -
Password check failed CNU90243DN
PLS HELP HP MINI PASSWORD CHECK FAILED ....CNU90243DN
Do you have Recovery Disc to boot from and reinstall Windows?
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
Hi
On my macbook pro
I'm try to set up a new Epson printer SX 445 to my router/network but each time I run the set up wizard it fails to complete saying Security Key/Password Check fail.
*entered security key/password does not match the one set for for router.
I know that the password is correct and have rechecked this by changing it a few times
and I still get the same result.
My network internet service provider is not interested and says to call Epson.
Anybody have any clues how I can resolve this?
RegardsI personally suggest the new Drobo FS. Since it has an iTunes server built in and you can use any size sata hard drive in it it is better and a NAS that has to use the same size drives.
-
Hp mini 1101 password check failed. CNU941460D
hp mini 1101 password check failed. CNU941460Dplease help me . I dono what to do..
Welcome Sidtheguy. Try.
e9lov3vg1t
Third letter lowercase L.
I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damage that may arise to your system by using these services. Please be aware that you do this at your own risk.
HP Expert Tester "Now testing HP Pavilion 15t i3-4030U Win8.1, 6GB RAM and 750GB HDD"
Loaner Program”HP Split 13 x2 13r010dx i3-4012Y Win8.1, 4GB RAM and 500GB Hybrid HDD”
Microsoft Registered Refurbisher
Registered Microsoft Partner
Apple Certified Macintosh Technician Certification in progress. -
Compaq mini 700 model 735ED windiws 7 password check failed system halted CNU91453V3
Ciao sono nuovo nella comunita ,e non so ancora bene come funziona.
ma come o gia detto o un compaq mini 700 model 735ED con windiws 7 e ho acceso stamattina e sulla schermata nera mi diceva di inserire la password al bios ,(non so se ci ha messo le mani mio figlio ma e strano) quindi dopo vari di inserimenti password mi dice " password check failed system halted CNU91453V3" vi prego aiutatemiHi,
Please see the reply on your earlier thread on the following link.
http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/hp-mini-compaq-700/m-p/4491550#...
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
Password checK fail CNU90243DN
passwod check failed fatal error...system halted. CNU90243DN
@khave1
Try >> e9lo17vft9 3rd letter is lowercase L
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
Password change fails in SQL Developer with verify function...
A couple of months ago I enforced a password verify function on our 11.2.0.3 databases and also one legacy 10.2.0.4 database.
At the time I tested on my account (which had elevated privileges...doh!). Now some users are hitting expiry, they can't change it via SQL Developer.
If I create a user with 'create session' privilege and set their profile to one that uses the verify function (see both below), I then log in to SQL Developer (we have tried with versions 3.1 (Windows) and 3.2 (Linux) with same failure results.
BTW,.. the password verify function enforces the following:
password must be minimum of 8 characters
password must not be the same as the user name, or user name (1-100)
password must contain at least a single digit
password must contain at least a single character
1. Works = I log into the local server and run command line SQLPlus, type 'password' and update. I can successfully change my password.
2. Fails = I log into the local server and run command line SQLPlus, type 'alter user <me> identified by <newpwd>;' I get:
TEST: SUTEMP > alter user sutemp identified by carport9999;
alter user sutemp identified by carport9999
ERROR at line 1:
ORA-28221: REPLACE not specified
This error is because the account does not have the 'alter user' privilege. I'm okay with this, as I don't want our users having this privilege.
3. I start SQL Developer 3.2, type 'alter user <me> identified by <newpwd>;' I get the same ORA-28221 error as above. That is fine, and as expected.
4. Now in SQL Developer, I type 'password', set a valid password, but I get 'Failed to change password' in the Script Output tab.
I have a database 'after servererror on database' trigger set, and querying the database table it is logging into, I see a record with a date stamp matching my failure with a server_error=28221 (the same as above).
So I'm wondering if I'm doing something wrong here, or if this is a bug in SQL Developer. I don't want standard users having 'alter user' privileges, but I do want to enforce password verification.
I get the same result on three 11.2.0.3 databases (haven't tried any more but suspect same results for others) and one legacy 10.2.0.4 database, and using SQL Developer 3.1 and 3.2.
DBA_PROFILE used:
PROFILE
RESOURCE_NAME
RESOURCE LIMIT
CTRU
COMPOSITE_LIMIT
KERNEL DEFAULT
CTRU
SESSIONS_PER_USER
KERNEL 10
CTRU
CPU_PER_SESSION
KERNEL DEFAULT
CTRU
CPU_PER_CALL
KERNEL DEFAULT
CTRU
LOGICAL_READS_PER_SESSION KERNEL DEFAULT
CTRU
LOGICAL_READS_PER_CALL
KERNEL DEFAULT
CTRU
IDLE_TIME
KERNEL DEFAULT
CTRU
CONNECT_TIME
KERNEL DEFAULT
CTRU
PRIVATE_SGA
KERNEL DEFAULT
CTRU
FAILED_LOGIN_ATTEMPTS
PASSWORD 10
CTRU
PASSWORD_LIFE_TIME
PASSWORD 180
CTRU
PASSWORD_REUSE_TIME
PASSWORD DEFAULT
CTRU
PASSWORD_REUSE_MAX
PASSWORD 5
CTRU
PASSWORD_VERIFY_FUNCTION PASSWORD VERIFY_FUNCTION_11G
CTRU
PASSWORD_LOCK_TIME
PASSWORD .002
CTRU
PASSWORD_GRACE_TIME
PASSWORD 21
16 rows selected.
Verify Function used:
$ cat utlpwdmg.sql
Rem
Rem $Header: utlpwdmg.sql 02-aug-2006.08:18:05 asurpur Exp $
Rem
Rem utlpwdmg.sql
Rem
Rem Copyright (c) 2006, Oracle. All rights reserved.
Rem
Rem NAME
Rem utlpwdmg.sql - script for Default Password Resource Limits
Rem
Rem DESCRIPTION
Rem This is a script for enabling the password management features
Rem by setting the default password resource limits.
Rem
Rem NOTES
Rem This file contains a function for minimum checking of password
Rem complexity. This is more of a sample function that the customer
Rem can use to develop the function for actual complexity checks that the
Rem customer wants to make on the new password.
Rem
Rem MODIFIED (MM/DD/YY)
Rem suren 05/09/13 - customise for NIHI use
Rem asurpur 05/30/06 - fix - 5246666 beef up password complexity check
Rem nireland 08/31/00 - Improve check for username=password. #1390553
Rem nireland 06/28/00 - Fix null old password test. #1341892
Rem asurpur 04/17/97 - Fix for bug479763
Rem asurpur 12/12/96 - Changing the name of password_verify_function
Rem asurpur 05/30/96 - New script for default password management
Rem asurpur 05/30/96 - Created
Rem
-- This script sets the default password resource parameters
-- This script needs to be run to enable the password features.
-- However the default resource parameters can be changed based
-- on the need.
-- A default password complexity function is also provided.
-- This function makes the minimum complexity checks like
-- the minimum length of the password, password not same as the
-- username, etc. The user may enhance this function according to
-- the need.
-- This function must be created in SYS schema.
-- connect sys/<password> as sysdba before running the script
CREATE OR REPLACE FUNCTION verify_function_11G
(username varchar2,
password varchar2,
old_password varchar2)
RETURN boolean IS
n boolean;
m integer;
differ integer;
isdigit boolean;
ischar boolean;
ispunct boolean;
db_name varchar2(40);
digitarray varchar2(20);
punctarray varchar2(25);
chararray varchar2(52);
i_char varchar2(10);
simple_password varchar2(10);
reverse_user varchar2(32);
BEGIN
digitarray:= '0123456789';
chararray:= 'abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ';
-- Check for the minimum length of the password
IF length(password) < 8 THEN
raise_application_error(-20001, 'Password length less than 8');
END IF;
-- Check if the password is same as the username or username(1-100)
IF NLS_LOWER(password) = NLS_LOWER(username) THEN
raise_application_error(-20002, 'Password same as or similar to user');
END IF;
FOR i IN 1..100 LOOP
i_char := to_char(i);
if NLS_LOWER(username)|| i_char = NLS_LOWER(password) THEN
raise_application_error(-20005, 'Password same as or similar to user name ');
END IF;
END LOOP;
-- Check if the password contains at least one letter, one digit
-- 1. Check for the digit
isdigit:=FALSE;
m := length(password);
FOR i IN 1..10 LOOP
FOR j IN 1..m LOOP
IF substr(password,j,1) = substr(digitarray,i,1) THEN
isdigit:=TRUE;
GOTO findchar;
END IF;
END LOOP;
END LOOP;
IF isdigit = FALSE THEN
raise_application_error(-20008, 'Password must contain at least one digit, one character');
END IF;
-- 2. Check for the character
<<findchar>>
ischar:=FALSE;
FOR i IN 1..length(chararray) LOOP
FOR j IN 1..m LOOP
IF substr(password,j,1) = substr(chararray,i,1) THEN
ischar:=TRUE;
GOTO endsearch;
END IF;
END LOOP;
END LOOP;
IF ischar = FALSE THEN
raise_application_error(-20009, 'Password must contain at least one digit, and one character');
END IF;
<<endsearch>>
-- Check if the password differs from the previous password by at least
-- 3 letters
IF old_password IS NOT NULL THEN
differ := length(old_password) - length(password);
differ := abs(differ);
IF differ < 3 THEN
IF length(password) < length(old_password) THEN
m := length(password);
ELSE
m := length(old_password);
END IF;
FOR i IN 1..m LOOP
IF substr(password,i,1) != substr(old_password,i,1) THEN
differ := differ + 1;
END IF;
END LOOP;
IF differ < 3 THEN
raise_application_error(-20011, 'Password should differ from the old password by at least 3 characters');
END IF;
END IF;
END IF;
-- Everything is fine; return TRUE ;
RETURN(TRUE);
END;
alter profile ctru limit password_verify_function verify_function_11g;
alter profile default limit password_verify_function verify_function_11g;
alter profile web_and_it limit password_verify_function verify_function_11g;okay,... I just saw another website which shows I should put in the 'replace <oldpwd>' clause in.
This works in SQL Developer: alter user sutemp identified by carport999 replace garage999;
So why does the 'password' command fail? (Developers: it would also be helpful to have the ORA- error displayed as opposed to 'Failed to change password') -
User equivalence check failed in solaris 10
Hi,
i am trying to install oracle clusterware on solaris10.
when i executed clusture varification utility , user equivalence test is failed.
each node have same username,userid,group id
and i configured SSH also using
exec /user/bin/ssh-agent
/usr/bin/ssh-add after generation of rsa and dsa keys and putting this to authorization file.
it is not asking password for ssh and scp after executing this command but again user equivalence check failed
but after logging of and do login again to oracle user its not working. then again i have to set ssh that is
exec /user/bin/ssh-agent
/usr/bin/ssh-add
wat else i have to check for this?
can sombody help me to solve thisUmesh Gupta wrote:
Thay are same, i have already taken care of that..
Node1:-
$ id oracle
uid=101(oracle) gid=300(oinstall)
Node2:-
$ id oracle
uid=101(oracle) gid=300(oinstall)
Please suggest..
Regards
Umesh$exec /usr/bin/ssh-agent $SHELL
$/usr/bin/ssh-add
on any one of the nodes
and check the output of cluvfy
also refer the link:-
http://download.oracle.com/docs/cd/B28359_01/install.111/b28263/crsunix.htm#BEHIHBBF
User equivalence check failed (RAC setup)
Edited by: rajeysh on Aug 18, 2011 7:09 PM -
CLUVFY failing with 'User Equivalence check failed for...'
New 2 node RAC configuration. Oracle 10gR2, Linux RHEL 5 x64. I'm at the post hardware config, pre install clusterware stage.
Running the cluster verification utility command:
cluvfy comp sys -n node-01,node-02 -p crs -verboseReturns the following error:
Verifying system requirement
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Verification of system requirement was unsuccessful on all the nodes.I've verified the following:
1) RSA keys correctly configured on both nodes and I can ssh between without a password
2) ping ip and private work correctly to and from both nodes.
3) user, group ids are identical on both systems.
I also ran cluvfy stage -post hwos -n node-01,node-02 -verbose and received the following output. This output is from node-01. node-02's is identical, except with equivalence to itself failing.
Checking node reachability...
Check: Node reachability from node "node-01"
Destination Node Reachable?
node-02 yes
node-01 yes
Result: Node reachability check passed from node "node-01".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
node-02 passed
node-01 failed
Result: User equivalence check failed for user "oracle".
WARNING:
User equivalence is not set for nodes:
node-01
Verification will proceed with nodes:
node-02
Checking node connectivity...I get the same behavior on both nodes. Not quite sure what else to check. Any thoughts or suggestions? Thanks.No, no banners. And I followed note 300548.1 to the letter. Several times :-)
However, I believe my issue has to do with a CVUHOME/cv/admin/cvu_config.
According to the documentation:
CV_XCHK_FOR_SSH_ENABLED—If set to TRUE, it enables the X-Windows check for verifying user equivalence with ssh. By default, this entry is commented out and X-Windows check is disabledIt was not, unfortunately, disabled by default - once I set it to false, everything succeeded. I still need to figure out why XCHK itself is failing, but I think I can troll through the log to figure that out. -
11g Cluster: User equivalence check failed on Node1 but passed on Node2,
From Node1:
[oracle@redhat4_1 bin]$ ./cluvfy stage -pre crsinst -n redhat4_1,redhat4_2 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "redhat4_1"
Destination Node Reachable?
redhat4_2 yes
redhat4_1 yes
Result: Node reachability check passed from node "redhat4_1".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
redhat4_2 passed
redhat4_1 failed
Result: User equivalence check failed for user "oracle".
WARNING:
User equivalence is not set for nodes:
redhat4_1
Verification will proceed with nodes:
redhat4_2
From Node2:
[oracle@redhat4_2 bin]$ ./cluvfy stage -pre crsinst -n redhat4_1,redhat4_2 -verbose
Performing pre-checks for cluster services setup
Checking node reachability...
Check: Node reachability from node "redhat4_2"
Destination Node Reachable?
redhat4_2 yes
redhat4_1 yes
Result: Node reachability check passed from node "redhat4_2".
Checking user equivalence...
Check: User equivalence for user "oracle"
Node Name Comment
redhat4_2 passed
redhat4_1 passed
Result: User equivalence check passed for user "oracle".
Why cluvfy failed on node1 but passed on node2? Thanks.Last time I saw that, the password-less SSH was working only in one direction. Root cause was not quite following the instructions to copy the authorized_keys to all nodes.
-
User equivalence check failed for user "oracle" while running cluvfy
Hi All,
I am getting User equivalence error as follows while executing cluvfy. I want to install CRS on this server.
oracle@node200$ ./runcluvfy.sh stage -pre crsinst -n node200,node201,node202
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "node200".
Checking user equivalence...
User equivalence check failed for user "oracle".
Check failed on nodes:
node202,node201,node200
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Pre-check for cluster services setup was unsuccessful on all the nodes.
I have sucessfully configured ssh and able to do ssh from all the nodes without prompting for the password. Also oracle uid and gid on all the servers are same.
I also checked in .kshrc file and there is no tty entry in that file. and I have also setup /etc/hosts.equiv file on all the node.
I still get the user equivalance error. Can anybody help me in this ?
Regards,
Raj.Hi,
thanks.
i need some more help because first time i am working on RAC,
i am also having User equivalence check failed for user "oracle"
i got two machines, one is IBM machine and one is DELL machine installed with solais 10 (AIX installation). both machines are not connected by private network now. and no shared external HDD available now. it will take one week time to set up the HW. the user equivalence check depends the above two factors?
now public network is available and node reachability test "passed"
could you please tell me what may be the reason for the user equivalence check in my case. details are given below
i have oracle user in both machine. user creation done through SMC. home directory is /export/home/oracle
the following are the details.
1) $ ssh pc000905 id -a oracle
Enter passphrase for key '/home/oracle/.ssh/id_rsa':
uid=100(oracle) gid=300(oinstall) groups=301(dba)
$ ssh pc026376 id -a oracle
Enter passphrase for key '/home/oracle/.ssh/id_rsa':
uid=100(oracle) gid=300(oinstall) groups=301(dba)
2) user nobody exists.
3) all files n .ssh directory have same permissions.
4) ssh and scp is working with out password(rsa and dsa keys generated).
5) oracle user is using bourne shell
6)soft link of /usr/bin/ssh and /usr/bin/scp are created to /export/home/oracle/bin
7)ForwardX11 is "yes" in sshd_config
8) created a config file in .ssh directory and ForwardX11 is "no" in that file
8) umask =022 in both nodes.
error displaying is
$/export/gome/cluvfy/runcluvfy.sh stage -pre crsinst -n pc026376,pc000905
Performing pre-checks for cluster services setup
Checking node reachability...
Node reachability check passed from node "PC026376".
Checking user equivalence...
User equivalence check failed for user "oracle".
Check failed on nodes:
pc026376,pc000905
ERROR:
User equivalence unavailable on all the nodes.
Verification cannot proceed.
Pre-check for cluster services setup was unsuccessful on all the nodes.
$
Maybe you are looking for
-
Problem with SystemTray on FC5 KDE
Hello! I'm trying to use new Java6 feature - SystemTray. There is problem with it on my Fedora Core 5 in KDE - system tray icon simply goes crazy (it appears and disappears, mainly disappears :( , sometimes it is moving on system tray in random direc
-
Documents, Movies, Pictures folder icons haven't been updated to the new Yosemite. All the other icons have (OneDrive, Google Drive haven't but I figured that has more to do with them). Does anyone have an idea of how to make those look like the new
-
Can't install itunes - "There is a problem with this Windows Installer package. A DLL required for this install to complete could not be run." Using Windows 7
-
Hi, We are facing a problem during phase PMVNTAB_UPG, at this point shadow instance is no longer used and the system has been switched to the new version (6.0). The problem exists with a Z view that does not exists in the database and we did enter us
-
Please help, my Macbook Pro running very very slow...virus?
Hi all, my macbook pro is running very very slow, report and spec list as follow, thanks! MBP 500GB : 2.4ghz Intel core i5 / 4gb DDR3 / OS10.9.5 report from Disk Utility: Permissions differ on "System/Library/CoreServices/Feedback Assistant.app"; sho