Password recovery at catalyst 4507R-E

Hi. I have catalyst 4507R-E and 2 engines are located at this catalyst. the engines are active standby. when i begin to recover i write the recover config at main engine then i must be reset the catalyst after reboot active engine go to satndby and standby go to active. so i can not recover it.
how can i solve this?
must i first remove standby engine and then recover active engine
then put the standby and active engine configuration go to standby.
am i rigth? i am afraid the i lost the configuration because i have not backup configuration.
i used this PDF.
please write your comment.
thank you very much.

Hi teymur,
You never lost your configuration, what you need to do is...
1. Make a complete config synch between active and standby supervisor engine (I hope autosync is already enabled)
2. Write the config to NVRAM on standby supervisor engine.
3. Now when you put back the standby supervisor engine, reload the active supervisor engine whcih take the standby be active and active be standby.
Also I would like to infor the password recovery procedure for you...
Try the below procedure with only one supervisor in the chassis.
1) Connect the console cable to the Supervisor IV console port
2) Reset the 4507 by power cycling the unit.
3) Interrupt the boot sequence by hitting CTRL+C
4) Using the confreg command, I set it to skip the boot-up configuration.
5) I issue the reset command to reboot the 4507 again.
http://www.cisco.com/en/US/products/hw/switches/ps663/products_password_recovery09186a00800945f7.shtml
Please rate the helpful posts.
Regards,
Naidu.

Similar Messages

Password Recovery for Catalyst 6500

Hi all,
According to this website:
http://www.cisco.com/en/US/products/hw/switches/ps708/products_password_reco
very09186a00801349aa.shtml
Password will not be activated in the first 30 second, so when we want to do
the password recovery, we just press enter and quickly change the password.
I tried this in the Cat 6509 but found a different result. When I press
enter, it didn't go to console (prompt) instead, it keep asking me the
password.
Is there anything change in the password recovery for Cat 6500 (I've done it
before but when I try it again, it showed a different result). FYI, i use
this version of CatOS = cat6000-sup2k9.7-6-12.bin
Regards,
Affandi Indraji

Hi Friend,
There is no change in the password recovery procedure it is just that you might not be doing it fast enough in 30 seconds.
Just power off and power on the switch again and then immediately try hitting enter as soon as it prompts for the first password and then follow the same procedure what you used to do for other CATOS switches.
HTH, if yes please rate the post.
Ankur

Password problem on Catalyst 3750

Hi all,
I am an Unix administrator and we lost all account and password informations to connect on a Catalyst 3750 switch.
Is there a way to connect to the switch (With a serial cable?) an to create a new account without losing the configuration ?
Thank's for your reply.
Regards.

This method won't reset the configuration.
During the boot process, you rename the current configuration so it doesn't get loaded.
rename flash:config.text flash:config.old
When the switch boots, it loads a blank image. Then you rename the config file and load it into the running config and you can change the logon credentials to something you know.
It's important that you follow the steps exactly so you don't lose the configuration. Password recovery is a pretty common procedure.
The only other method of recovery is if you have a copy of the current running configuration. Send me a private message if you have this config and we can discuss the possibility.

Catalyst 4507R-E

Hi
I am using catalyst 4507 R-E
I did the password recovery and then when I reloaded the below info appears in the rommom mode
please help
as how can solve this problem
I have reloaded several times but its the same
* Welcome to Rom Monitor for WS-X4515 System. *
* Copyright (c) 1999-2004 by Cisco Systems, Inc. *
* All rights reserved. *
Rom Monitor Program Version 12.2(20r)EW1
Supervisor: WS-X4515 Chassis: Unknown( 5 )
Hardware Revisions - Board: 2.14 CPLD: 32 Dagobah: 226
MAC Address : 00-15-c6-bd-d3-54
IP Address : 10.10.10.10
Netmask : 255.255.255.0
Gateway : Not set.
TftpServer : 10.10.10.11
Main Memory : 512 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
******** The system will autoboot now ********
config-register = 0x2102
Autobooting using BOOT variable specified file.....
Could not find a valid file in BOOT environment variable.
BOOT variable can be set from IOS. To find currently set
Rom Monitor variables, please type 'set' command.
For help on choosing a boot method, type 'confreg' command.
rommon 1 >
rommon 1 >

Hi
I am using catalyst 4507 R-E
I did the password recovery and then when I reloaded the below info appears in the rommom mode
please help
as how can solve this problem
I have reloaded several times but its the same
* Welcome to Rom Monitor for WS-X4515 System. *
* Copyright (c) 1999-2004 by Cisco Systems, Inc. *
* All rights reserved. *
Rom Monitor Program Version 12.2(20r)EW1
Supervisor: WS-X4515 Chassis: Unknown( 5 )
Hardware Revisions - Board: 2.14 CPLD: 32 Dagobah: 226
MAC Address : 00-15-c6-bd-d3-54
IP Address : 10.10.10.10
Netmask : 255.255.255.0
Gateway : Not set.
TftpServer : 10.10.10.11
Main Memory : 512 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
******** The system will autoboot now ********
config-register = 0x2102
Autobooting using BOOT variable specified file.....
Could not find a valid file in BOOT environment variable.
BOOT variable can be set from IOS. To find currently set
Rom Monitor variables, please type 'set' command.
For help on choosing a boot method, type 'confreg' command.
rommon 1 >
rommon 1 >

Password recovery for 2960 without loosing configuration

Hi,
I don't remember password for Cisco 2960 switch, now i want to recover the password. I have checked few documents but would like to know few things before following these steps.
1. Is password recovery procedure for Cisco 2960 switch is different from normal ctr+break then change the register method? As i am more confident of doing this procedure than using mode button and then renaming the configuration file.
2. If i follow below procedure then hope it won't erase the configuration including vlans information.?
https://supportforums.cisco.com/discussion/11756896/cisco-switch-29603560-password-recovery-and-factory-default-mode-button
3. Pressing mode button is an alternate to using ctrl+break sequence? and long pressing of mode button does't effect anything.
4. Restarting the switch after pressing mode button (without making any changes) will go back to previous configuration (working condition).
Thanks.

1. Is password recovery procedure for Cisco 2960 switch is different from normal ctr+break then change the register method? As i am more confident of doing this procedure than using mode button and then renaming the configuration file.
Password recovery for switches, like the Catalyst 2K and 3K, are far more simpler. Read this: Cisco Catalyst Fixed Configuration Layer 2 and Layer 3 Switches
2. If i follow below procedure then hope it won't erase the configuration including vlans information.?
https://supportforums.cisco.com/discussion/11756896/cisco-switch-29603560-password-recovery-and-factory-default-mode-button
I've posted a link above. I'd recommend you read that one. The link you've posted is about someone who wants to make a simple procedure look complicated.
3. Pressing mode button is an alternate to using ctrl+break sequence? and long pressing of mode button does't effect anything.
Correct. Get your mindset out of the password recovery of routers. When you are dealing with some models of switches, it's the "Mode" button. There are no "Mode" buttons in routers, hence, the Ctrl+Break key is required.
4. Restarting the switch after pressing mode button (without making any changes) will go back to previous configuration (working condition).
If you did NOT rename the configuration file, yes, the switch will reboot and load the existing configuration file.
If you renamed the configuration file, the switch will reboot. Finding no configuration file, the switch will load the factory defaulted configuration.

What is a password recovery email address

Hi,
I am looking at the info page on setting up clien email http://helpx.adobe.com/business-catalyst/partner/setup-pop-imap-email-accounts.html in the Creat email accounts for users section, it says, "Enter the new user email address, name and password recovery email address." What is the password recovery email address? Also would the new user email address be the users name@my_domain_name.com? Thanks.
Barbara Parkman

Hi Barbara,
Keep in mind the Muse webBasic plans do not include email.
The password recovery email address is an email address that they could have their password emailed to in case they forget it. Obviously sending it to the same email address wouldn't work as they wouldn't be able to get it.
Yes, the email address would be @clientdomain.com ....
As a side note I recommend hosting the email with where ever they bought the domain from and only use Business CAtalyst for the site itself.
Here is why ...
http://www.lawryk.com/BlogRetrieve.aspx?PostID=578206

Blackberry ID - forgot password, forgot password recovery info, exceeded login attempts, why can't BB send me email to reset password.

THE ISSUES ARE:
1. FORGOT PASSWORD
2. FORGOT PASSWORD RECOVERY INFO
3. EXCEEDED ATTEMPTS TO LOGIN
I HAVE READ OTHER PEOPLES FORUM PROBLEMS THAT ARE THE SAME. WHEN I FOLLOWED LINKS THAT SUPPORT GAVE THERE IS NO SOLUTION TO ACTUALLY FIX THE PROBLEM.
What I need is simply this: Blackberry to send me a RESET PASSWORD link to the email I have registered with Blackberry WITHOUT HAVING TO PROVIDE PASSWORD RECOVERY INFO. This will enable me to bypass unknown recovery password info and access my Blackberry ID account.
Why haven't I been able to find a solution to fix the problem?
BECAUSE IT DOESN'T APPEAR TO EXIST........ ANYWHERE..... EVEN ON YOUTUBE BLACKBERRY ARE RUNNING AN OUT OF DATE SOLUTION CENTRE.
When looked online to Blackberry youtube video it shows a solution that doesn't exist! WHY? BECAUSE IT WAS UPLOADED IN 2011. DUH. http://www.youtube.com/watch?v=lvdRb4qNG1M
If I can't remember my password or recovery password info there is NO other option available that will send me a reset password via email so I can keep my current BB ID.
KB34776 - does not apply because you HAVE TO BE ABLE TO REMEMBER YOUR RECOVERY PASSWORD!
CHECKED THIS OUT...
Workaround
If the BlackBerry ID password has been forgotten but the answer to the password recovery question is known, select Forgot Password on the smartphone and answer the recovery question to generate a password reset email. Follow KB28685 to complete this process.
If the BlackBerry smartphone user knows the email address used for the BlackBerry ID login but is unable to remember the associated password then it is possible to reset the password using the steps below:
Note: If the BlackBerry ID account is not confirmed, it is necessary to provide the answer to the password recovery question as part of the web based password reset flow.
To see if a BlackBerry ID account is confirmed, log in to the BlackBerry ID account, select Account Details and locate the Email Status field.  For instructions on confirming the BlackBerry ID account follow KB34137.
Browse to the following URL using a desktop browser, the BlackBerry Browser on the BlackBerry smartphone, or the Browser on the BlackBerry PlayBook: http://blackberryid.blackberry.com/bbid/recoverpassword
Enter the BlackBerry ID Username (email address) and the CAPTCHA characters, then clickSubmit.
Enter the Answer to the Password Recovery Question, then click OK.
Note: Answering the recovery question is only required if the BlackBerry ID account is not confirmed.
A confirmation message will be displayed A password reset email has been sent to [email protected], at which point, a reset email will be delivered to the associated email address inbox.
Log in to the email account associated to the BlackBerry ID using the desktop browser, BlackBerry Browser on the smartphone, or the Browser on the BlackBerry PlayBook.
Locate the password reset email and select the Change your BlackBerry ID password link.
Note: The BlackBerry ID reset email will come from [email protected]. If the email is not found in the inbox, check the mailbox's Spam or Junk folder.
When the password reset page loads, enter the Answer to the Password Recovery Question, enter the New Password, Confirm Password, then click Submit.
A confirmation message will display once the changes have been saved successfully.
Moving forward use the newly created password whenever logging into BlackBerry ID.
If the BlackBerry smartphone user does not know the email or password that was used for the BlackBerry ID, the BlackBerry ID will be locked out after 10 unsuccessful login attempts. See KB24157 for BlackBerry ID lockout behavior.
THEN CHECKED KB24157......
Overview
BlackBerry ID is the master key to BlackBerry smartphone products, sites, services and applications, including BlackBerry Protect and the BlackBerry App World storefront.
To prevent unauthorized access to the account, the BlackBerry ID will become locked out after a number of failed attempts. See the information below for an outline on the expected behavior:
Local Authentication Lockout
On BlackBerry PlayBook and BlackBerry smartphones if the user enters their BBID password incorrectly 10 times on the BBID sign in screen, verify password screen, or BBID Edit screens, they are LOCKED OUT of all the following functions on that BlackBerry device for 15 minutes:
Authenticating with their BlackBerry ID on the sign in screen
Authenticating with their BlackBerry ID on the verify password screen
Authenticating with their BlackBerry ID on the BBID edit screens
Note: The user can still log in on the web or any other devices associated with their BlackBerry ID. They are only locked out on the device where the 10 incorrect attempts occurred. On the locked out device, after 15 minutes, they get 1 try to provide the correct password on the sign in and/or verify password screens. If they fail to enter the correct password, they are locked out for an additional 15 minutes on that device.
Account Server Lockout
Users have total of 10 attempts to enter their password correctly against the BlackBerry ID Account Server.
The scenarios that increment the Account Server lockout counter are as follows:
Providing an incorrect password anywhere on the BlackBerry ID web portal (blackberry.com/blackberryid)
Providing an incorrect password within the BlackBerry ID Edit feature on any BlackBerry device or BlackBerry PlayBook
Note: if a user provides an incorrect password 5 times on the BlackBerry ID web portal (blackberry.com/blackberryid), and then 5 more times on the BlackBerry ID Edit feature on their BlackBerry PlayBook, the cumulative number of failed attempts is 10. Once the user has made 10 incorrect attempts to provide their password against the Account Server, they are locked out of the Account Server PERMANENTLY until they reset their password.
See KB26361 for information to reset a BlackBerry ID password
Note: The Account Server Lockout does NOT prevent the user from local authenticating on devices (the user can still authenticate on the sign in and verify password screens on their BlackBerry devices).
Forgot Password Lockout
If the user answers their Security Question incorrectly 10 times, they are locked out for 15 minutes of Forgot Password functionality on all interfaces such as:
BlackBerry website (blackberry.com/blackberryid)
BlackBerry PlayBook
BlackBerry smartphone
Note: After 15 minutes, they get 1 try, and if they fail to answer the question correctly, they are locked out for an additional 15 minutes.
THAT DIDN'T WORK SO NOW ITS BACK TO..... KB26361
Overview
To change the BlackBerry ID password, complete the steps below for the specific device:
From the BlackBerry 10 smartphone:
Swipe down from the top bezel on the home screen and select Settings.
Scroll down and select BlackBerry ID.
Select Change Password.
Enter the current password in the Current BlackBerry ID Password field.
Enter the new password in the New BlackBerry ID Password and Confirm New Passwordfields.
Select Submit to complete the password change.
To confirm the change You have changed your password will be displayed.
Also, if the BlackBerry ID password has been forgotten, select Forgot Password on the smartphone and answer the recovery question to generate a password reset email. Follow KB28685 to complete this process.
Note: When using the recovery question password reset method, the generated email will be delivered to the BlackBerry 10 smartphone if the BlackBerry ID email address has been setup via Settings >Accounts
From a computer:
Visit http://www.bbid.com/ from a PC or BlackBerry smartphone browser.
Click Log in.
Enter the BlackBerry ID Username (email address) and password, then click Sign In.
Click Account Details.
Next to Password, click Edit.
Enter in the current password, followed by the new password. Enter the new password again in the confirm password field, then click Save.
Click Done to exit from the BlackBerry ID account information screens.
From the BlackBerry smartphone running BlackBerry 6:
Navigate to Options > Third Party Applications > BlackBerry ID.
Click on Change next to BlackBerry ID Password.
Enter in the current password, followed by the new password. Enter the new password again in the confirm password field, then click OK.
A confirmation message will display Your password has been successfully changed.
Click OK.
From the BlackBerry smartphone running BlackBerry 7:
Navigate to Options > Device > BlackBerry ID.
Click on Change next to BlackBerry ID Password.
Enter in the current password, followed by the new password. Enter the new password again in the confirm password field, then click OK .
A confirmation message will display Your password has been successfully changed.
Click OK.
From the BlackBerry Playbook tablet:
Navigate to the Options icon.
Select BlackBerry ID.
Click on the Edit button next to Change Password.
Enter in the current password, followed by the new password. Enter the new password again in the confirm password field, then click Submit.
A confirmation message will display You have changed your password.
Click OK.
If the password for a BlackBerry ID account has been forgotten and the login is unsuccessful, use the following process to reset the password.
Note: If the BlackBerry ID account is not confirmed, it is necessary to provide the answer to the password recovery question as part of the web based password reset flow.  To see if a BlackBerry ID account is confirmed, login to the BlackBerry ID account, select Account Details and locate the Email Status field.  For instructions on confirming the BlackBerry ID account follow  KB34137.
To generate a password reset email, complete the following:
Browse to the following URL using a desktop browser, the Browser on the BlackBerry smartphone or the Browser on the BlackBerry PlayBook: http://blackberryid.blackberry.com/bbid/recoverpassword
Enter the BlackBerry ID Username (email address) and the CAPTCHA characters, then clickSubmit.
Enter the Answer to the Password Recovery Question, then click OK. (Answering the recovery question is only required if the BlackBerry ID account is not confirmed)
A confirmation message will be displayed A password reset email has been sent to [email protected] , at which point, a reset email will be delivered to the associated email address inbox.
Login to the email account associated to the BlackBerry ID using the desktop browser, BlackBerry Browser on the BlackBerry smartphone or the browser on the BlackBerry PlayBook.
Locate the password reset email and select the Change your BlackBerry ID password link.
Note: The BlackBerry ID reset email will come from [email protected] If the email is not found in the inbox, check the Spam or Junk folder.
When the password reset page loads, enter the Answer to the Password Recovery Question, enter the New Password, Confirm Password, then click Submit.
Note: Answering the recovery question is only required if the BlackBerry ID account is not confirmed.
A confirmation message will display once the changes have been saved successfully.
Moving forward use the newly created password whenever logging into BlackBerry ID.
Note: If the BlackBerry ID email address is a BlackBerry mail address (e.g. <username>@tmo.blackberry.net), the BlackBerry ID password reset email will not be received on the BlackBerry smartphone. Since the BlackBerry mail address is not accessible from a computer, the steps outlined in KB28111 will need to be performed.
IT ALL LEADS BACK TO THE SAME UNHELPFUL NON-SOLUTION OF USE THE PASSWORD RECOVERY QUESTION....
Can the tech department of Blackberry please sort out this ridiculous unhelpful system by sending customers a direct email if password is forgotten so they can reset without having to go through the above without finding a solution.
THANK YOU.

Hi and Welcome to the Community!
Please see this "sticky" post, along with the threads to which it links, for helpful information to guide you as you proceed:
http://supportforums.blackberry.com/t5/Social-Lounge/How-This-Site-and-Formal-Support-Work/td-p/2540...
Hopefully, this information will be of use to you.
That said, it sounds like you have exhausted all of the automatic recovery methods...but just in case, please see this "sticky" post for helpful information concerning your BBID situation:
http://supportforums.blackberry.com/t5/BlackBerry-World/How-to-regain-access-to-your-BBID/td-p/25467...
Hopefully, this information will be of use to you.
But do please keep in mind that security is a 2-way street...the human element play an equal part in that security, and you have failed at that in this situation, yet desire for the automated methods to still recover for you. Such just isn't possible, because your failure has exceeded the capabilities of the automated methods.
Hence, you likely need human intervention from an actual BB representative, which is not available in this forum (as discussed in the first link I gave you above). But, the methods to attempt to seek human intervention are posted within the 2nd link I gave you.
Cheers, and Good Luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

My safari keeps crashing because of a bat password recovery plug in. What do I do to fix it?

My safari keeps crashing on me, and when it does it always says it was because of some Bat! Password Recovery Plugin. How can I fix this and stop t from happening?

You’ve been infected with the “Flashback” malware. See this Apple support document:
About Flashback malware
Back up all data, if you haven't already done so.
Select  ▹ Software Update to install the latest Java update (if Java is already installed) or the Flashback malware removal tool (if Java is not installed under Lion), as well as any other available updates. Installing either of those items should clear the infection in most cases. No other action is required on your part. You must update to the latest version of Mac OS X 10.6 or 10.7 before you can install the Java update.
Change every Internet password you have, starting with banking passwords. Check all financial accounts for unauthorized transactions. Do this after you’ve secured your system, not before.

How do i bypass the windows password without password recovery disk

My sister has passed away & Ive been copying her pictures off of her laptop for the family & I havent finished. It logged off last night & now its asking for password & no one knows the password.. Im almost positive there is a way to go around this password but I cant seem to figure it out on my own! Please Help ASAP THANX

Here are some common methods.
 
Method 1: Reset Windows 7, Vista, XP Password Via Another Administrator Account
 
If you have another user account with admin privileges, including built-in accounts in Windows 7/Vista/XP, you can easily bypass other accounts' password using Lusrmgr.msc and Command Line.
 
1. Log on Windows 7/Vista/XP with your administrator account. Click on Start, type lusrmgr.msc in the Search box(Win7/Vista) or Run box(Win7/Vista/XP) and click OK.
2. When the Local users and Groups dialog appears, open the Users folder. Right-click your user account and select "set password", type a new password and click OK.
 
Method 2: Reset WIndows 7/Vista/XP password with Windows password reset disk
Here is the steps to reset Windows password with password reset disk, bypassing Windows Vista/XP password is the same as this:
 
Step 1: Login Windows with a incorrect password, it will show you a link "Reset Password.." under the password box.
Step 2: Insert your password reset disk, click the link, When a password reset wizard appears, click Next.
Step 3: Choose the drive name from the pull-down list, click Next.
Step 4: Type a new password in the new password box, and type it again to confirm it. Click Next→Finish. Then you can login Windows again with the new password.
 
Method 3: Reset Windows password with Windows password recovery program
 
In this method, you need to load a recovery program on another computer, then burn it to a CD/USB. Boot your locked computer from CD/USB and reset WIndows password offline. This is a universal password reset method.
[advertising content removed]
 
Hope helpful.

Hp password recovery in windows 8

I just wanted to tell you of a recent experience I had when contacting HP support
I called them yesterday with what I considered to be a simple question I found out that this question in their eyes was not that simple
the question was how do I set Up a password recovery flash drive in Windows 8.
the the person from HP said that he would need to check and would I please give him a minute to do so, when he came back he said that hp computers did not have this option.
I said to him how could this be as windows 8 says you can do this I also said that in windows vista and windows 7 you could do this and Why Would windows 8 Be any different he said he didn't know But this was not an option available hp in windows 8 he also stated
if I were to forget my password would be to install my operating system again. I said to him that it seemed unreasonable that I would have to reinstall my os just to recover my password and the must be a simpler option than that. he said no that would be my only option if I were to ever forget my password. I then said to him I did not believe the information he was giving me was accurate and was he 100% sure of the information he was giving me, he said yes and that he would send me an e-mail giving me step by step instructions. I said okay bye, I did not believe what he was telling me so I went online and found out in about 2 minutes all we needed to do was set this up via the settings screen and user account where it give you the option to make a password recovery usb flash drive I understand that they cannot possibly know everything but I feel if they don't know they should be willing to tell you that they don't know and passed you on to someone who does rather Than making you spend hours reinstalling an operating system that you don't need to. it also seems to me outsourcing technical support to third world countries like in this case india where they may not have a full grasp of some of the finer subtletys of the english language and company like hp dell toshiba and many others need to return technical support to the countrys in which the computers are sold and 1 other thing why is it that we no longer get a set of recovery cds with new computer and have to make a set ourselves when so often in the process of making them some write error happens and you only find out that is there is a problem with them when you come to use them I know companies need to make a profit on the sale of the computers but surely there is enough profit margin for them still to supplie you with the recovery media you need

Hi,
I afraid the pritner is not supported on Windows 8:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03457812&tmp_task=prodinfoCategory&cc=us&dlc=en...
You will not be able to use any other alternative driver with the printer as there are no drivers to allow the PC to communicate with the printer through a USB connection..
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Cisco ISE 1.2 vm cli admin password recovery

I'm having trouble getting this to work. I was under the impression by mounting the ISO (connect at power on) i could perform the password recovery like it states for the hardware appliance. However, if i mount the 1.2.0.899 iso image (connect at power) I don't seen to get any options in my vm console? At most, I have a <enter> at the very beginning that will take me to Grub or ADE boot menu... but I don't see anything about options to change the password?

Make sure you are following the steps in the following link:
http://www.cisco.com/c/en/us/td/docs/security/ise/1-2/installation_guide/ise_ig/ise_postins.html#38674
Also, make sure that the VM Guest is set to boot from DVD/CD first before trying the HDD.
Thank you for rating helpful posts!

I reset my disabled ipad 2 and it is asking me for the apple id which first set it up but i forgot the password for that apple id and the password/recovery information for the recovery email address. What can i do?

i reset my disabled ipad 2 and it is asking me for the apple id which first set it up but i forgot the password for that apple id and the password/recovery information for the recovery email address. What can i do?

Click here and use Apple's iForgot service, or contact their Account Security team, or if you're the device's original owner, take it and its purchase receipt to a physical Apple Store.
(124525)

I forgot my password recovery questions and i need it so i can purchase stuff on my ipad

i forgot my password recovery questions and i need it so i can purchase stuff on my ipad

Alternatives for Help Resetting Security Questions and/or Rescue Mail
     1. If you have a valid rescue email address, then use this procedure:
         Rescue email address and how to reset Apple ID security questions.
     2. Fill out and submit this form. Select the topic, Account Security. You must
         have a Rescue Email to use this option.
     3. This is the only option if you do not already have a valid Rescue Email.
         These are telephone numbers for contacting Apple Support in your country.
         Apple ID- Contacting Apple for help with Apple ID account security. Select
         the appropriate country and call. Ask to speak to the Account Security Team.
Note: If you have already forgotten your security questions, then you cannot
         set up a rescue email address in order to reset them. You must set up
         the rescue email address beforehand.
Your Apple ID: Manage My Apple ID.
                         Apple ID- All about Apple ID security questions.

ONS 15454 Password Recovery Cable

Does anyone know the part number for the password recovery cable needed to connect a laptop to the TCC card to used to reset the password to Cisco defaults? I have attached the cisco PDF which explains the connection of this cable.
Thanks

The part number is 15454-EPC=
In the past, you couldn't order this item but had to call Cisco TAC and request one.
Hope this helps.

Root Password Recovery Question

Hello all,
I have a question regarding root password recovery in Solaris 10.
The Server is a Sun Fire T1000; it has no CD-Rom drive, as well as no USB ports. One of our data architects who is the main user of this server has locked himself out of root (he also never created any other user accounts).
Now I know normally for root password recovery you use the solaris cd to boot into single user mode to take care of this but that's not an option currently. I was wondering if there is a way to put the hard drive as a slave in another Sun Fire T1000 server and then mount it and modify the shadow file removing the encrypted password. I've done this in other Linux OS's and it has worked but I didn't know about Solaris.
Any help would be greatly appreciated as it is for a project my company is working on and they have a presentation coming up in around 4-5 weeks.
Thank you!
-Mike

Well I tried making the locked out hard drive a slave on another server of the same type. But I couldn't seem to mount it, I even tried the "touch /reconfigure; init 6" to reconfigure devices but it just didn't seem to find it. I tried mounting everything in /dev/dsk but nothing was successful.
Anyone have any other suggestions on commands that might work?
I put a purchase order in for a USB to SATA converter, and got a hold of a different Sun server which has USB ports but no SATA, only IDE. As soon as I get it i'm going to try to mount it like a USB external hard drive. I believe when mounting USB it doesn't care if it's a jump drive or a external hard drive it should still mount it correctly. Hopefully this will allow me to modify the shadow file.
Thanks in advance if anyone has any other suggestions.

Password recovery at catalyst 4507R-E

Similar Messages

Maybe you are looking for