Password recovery for CSC-SSM

i have CSC ssm module in my lab. i forgot its username/password and also the ip address of csc module. when i tried to do reimgine the csc module, setup asks for ip address of csc module. is there is any way to recover password without knowing the ip address of CSC module.

This document describes how to recover a password on a Cisco ASA 5500 Series Content Security and Control Security Services Module (CSC-SSM) or the Advanced Inspection and Prevention Security Services Module (AIP-SSM) without having to re-image the device.
http://cisco.com/en/US/partner/products/ps6120/products_password_recovery09186a00807f5a59.shtml

Similar Messages

Password recovery for 2960 without loosing configuration

Hi,
I don't remember password for Cisco 2960 switch, now i want to recover the password. I have checked few documents but would like to know few things before following these steps.
1. Is password recovery procedure for Cisco 2960 switch is different from normal ctr+break then change the register method? As i am more confident of doing this procedure than using mode button and then renaming the configuration file.
2. If i follow below procedure then hope it won't erase the configuration including vlans information.?
https://supportforums.cisco.com/discussion/11756896/cisco-switch-29603560-password-recovery-and-factory-default-mode-button
3. Pressing mode button is an alternate to using ctrl+break sequence? and long pressing of mode button does't effect anything.
4. Restarting the switch after pressing mode button (without making any changes) will go back to previous configuration (working condition).
Thanks.

1. Is password recovery procedure for Cisco 2960 switch is different from normal ctr+break then change the register method? As i am more confident of doing this procedure than using mode button and then renaming the configuration file.
Password recovery for switches, like the Catalyst 2K and 3K, are far more simpler. Read this: Cisco Catalyst Fixed Configuration Layer 2 and Layer 3 Switches
2. If i follow below procedure then hope it won't erase the configuration including vlans information.?
https://supportforums.cisco.com/discussion/11756896/cisco-switch-29603560-password-recovery-and-factory-default-mode-button
I've posted a link above. I'd recommend you read that one. The link you've posted is about someone who wants to make a simple procedure look complicated.
3. Pressing mode button is an alternate to using ctrl+break sequence? and long pressing of mode button does't effect anything.
Correct. Get your mindset out of the password recovery of routers. When you are dealing with some models of switches, it's the "Mode" button. There are no "Mode" buttons in routers, hence, the Ctrl+Break key is required.
4. Restarting the switch after pressing mode button (without making any changes) will go back to previous configuration (working condition).
If you did NOT rename the configuration file, yes, the switch will reboot and load the existing configuration file.
If you renamed the configuration file, the switch will reboot. Finding no configuration file, the switch will load the factory defaulted configuration.

Which part number for CSC-SSM with Plus license?

Dear All,
Which part number for CSC-SSM with Plus License? i saw the part number for standard license.
could you let me know?
Best regards,

Hi,
The part number is the following:
ASA-CSCX-YP-ZY
where X is your CSC model, Y is the number of seats of the license and Z is the number of years.
For instance, if you need a 2 year plus license for a CSC10 with 250 seats, the part number would be ASA-CSC10-250P-2Y
Regards,
Nicolas

Password Recovery for Catalyst 6500

Hi all,
According to this website:
http://www.cisco.com/en/US/products/hw/switches/ps708/products_password_reco
very09186a00801349aa.shtml
Password will not be activated in the first 30 second, so when we want to do
the password recovery, we just press enter and quickly change the password.
I tried this in the Cat 6509 but found a different result. When I press
enter, it didn't go to console (prompt) instead, it keep asking me the
password.
Is there anything change in the password recovery for Cat 6500 (I've done it
before but when I try it again, it showed a different result). FYI, i use
this version of CatOS = cat6000-sup2k9.7-6-12.bin
Regards,
Affandi Indraji

Hi Friend,
There is no change in the password recovery procedure it is just that you might not be doing it fast enough in 30 seconds.
Just power off and power on the switch again and then immediately try hitting enter as soon as it prompts for the first password and then follow the same procedure what you used to do for other CATOS switches.
HTH, if yes please rate the post.
Ankur

Password recovery for linksys slm224g2 switch

what is password recovery for linksys slm224g2 switch

Hi Kalpesh.
Unfortunately this series of switches doesn't have a password recovery. Only the reset infront of the device.
If you have forgotten the device password you have to reset the switch to factory default to access the interface again.

Password Reset for AIP-SSM 10

Hi,
i have an ASA5520 with v 7.2(2) running.
but the IPS module spftware is 5.1
when i tried to login to the > session 1
it prompts me for a login and password.
i tried cisco and a few other combinations.. but no luck ,,
how do i reset it ?? also that reset procedure on the docs says its resets password or the user cisco ..
how can i be sure if the user cisco even exists on it or not ?
any help please ???

no man it doesnt ..
the link u specified says it too..
hw-module module slot_number password-reset?This command recovers a password on a Cisco ASA 5500 Series Content Security and Control Security Services Module (CSC-SSM) or the AIP-SSM without having to re-image the device.
Note: This command starts support from IPS 6.0 (ASA 7.2 version) and is used to restore the Cisco CLI account password to the default cisco
hers my ASA and IPS details..
ASA# sh version
Cisco Adaptive Security Appliance Software Version 7.2(2)
Device Manager Version 5.2(2)
Compiled on Wed 22-Nov-06 14:16 by builders
System image file is "disk0:/asa722-k8.bin"
Config file at boot was "startup-config"
ASA up 22 days 3 hours
Hardware: ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
ASA# sh module 1
Mod Card Type Model Serial No.
1 ASA5500 SSM-10 ASA-SSM-10 B155670DW4
Mod MAC Add Range Hw Ver. Fw Ver. Sw Ver.
1 00xx to 001 1.0 1.0(10)0 5.0(2)S152.0
Mod SSM Apps. Name Status SSM Apps Version
1 IPS Up 5.0(2)S152.0
Mod Status Data Plane Status Compatibility
1 Up Up

ASA 5520 : IP address for CSC SSM

Hi All,
I have an ASA 5520 with CSC SSM. I have base and plus license and want to activate it. T he IP address and gateway have to be configured on the CSC SSM. I have configured IP addresses for the INSIDE,OUTSIDE,DMZ and MGMT. The outside is a public IP address. Now for the CSC SSM what range should i give?
There is an ISA server on the DMZ where all user IP's get PATed and on ASA this gets NATed on the ASA. Direct access to the internet exists for the servers (bypassing proxy).
My basic doubt is about the IP address and gateway that the CSC SSM should have and is it related ot the management interface ip address?
Thanks and Regards.
Sonu

Hi
put your CSC ip address as outside interface subnet.because CSC needs automatic updates from internet.and you can able to manage CSC from remote itself.
for EX
your outside ip is 10.0.0.1/24,make CSC IP As 10.0.0.2/24,Gateway 10.0.0.1
Hopes this helps
regs
S.Mohana sundaram

Trend Micro updates for CSC SSM

Any word on if or when patch would be available for 6.3.1172 ? My ASA has only 256kb memory, and I believe it would require a memory upgrade for any further software upgrades.

The mail and TMCM agent service is always stopped. Access to CSC-SSM via web browser is not possible, nothing happens, and ASDM is not communicating with CSC. I restarted management access port, without success. Restore to Factory settings is not possible. I get this error message:
Restoring default settings: /opt/trend/isvw/bin/setup.bin: line 2861: /opt/trend/isvw/lib/mail/rules/UserApprovedList.txt: Read-only file system
/opt/trend/isvw/bin/setup.bin: line 2862: /opt/trend/isvw/lib/mail/rules/UserBlockedList.txt: Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/web/intscan.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
cp: unable to remove `/opt/trend/isvw/config/mail/imss.ini': Read-only file system
I try to reimage with 6.2 version, maybe this helps.
If you have a clue tell me!
Thank you

Password Recovery for Wireless Lan controller

Hi, I am new to Wireless Lan Controller.
I just wanted to reset the password for the Controller. Can anybody help me with this. link/procedure anything will be appreciated.
Thanks & Regards,
Jvalin

I think they mean that they can not type "reset system" since they can't log in in the first place.
The key point to be made is that you need to restart the controller. So power it off if you can't login. Then console in to the controller and type "Recover-Config" as the username. This will default the configuration and allow you to start over with a new username/password.
There is no other password "recovery".

Password Recovery for Windows XP Pro

I have recently found a Dell computer in my house that is in good working condition. After setting the computer up, I asked the original owner what the administrator password to the login was. Sadly, the owner doesn't remember the password. I have tried logging in through safe mode and pressing ctrl+alt+del twice and trying to log in then. These tries didn't work, and I have been scavenging around for any password recovery tool I could use. On my recent trip to Best Buy, I informed one of the employees about the problem I had. To solve it, he said to restart the computer and while it was loading, continually press the F8 key, which should log me in as Administrator and could reset the password from there. I have tried this, but failed, most likely not sure if I did it right.

I hope this doesn't come off as mean/offensive, but if you don't have a higher level of computer knowledge, doing an account password reset isn't the easiest thing in the world.
Your local Geek Squad, or any repair shop, should be able to remove the password for you for a fee(call around to see what it is, when I was in store it was $29.99).
There are password removal tools out there, but it requires downloading a disk image, burning it, and getting the computer to boot off the disk into a command prompt environment. It's not "hard" but if you don't know what you're getting into, it's easy to mess things up.
If you like my post, or solution to your issue/question, go ahead and click on the little star by my name and/or accept the post as the Solution. It makes me happy.
I'm NOT an employee of Best Buy, or Geek Squad, though I did work as an Agent for a year 5 years ago. None of my posts are to be taken as the official stance that Best Buy will take on your situation. My advice is just that, advice.
Unfortunately, that's the bad luck of any electronic, there's going to be bad Apples... wait that's a horrible pun.

ROMMON Password Recovery for 803 Router

Hello Netpros.
Whilst attempting to perform a standard enable password recovery on an 803 router, I discovered that a ROMMON password had been set. This had the significant disadvantage in that I could not set the config register to bypass the configuration on startup using the set command.
I've browsed Google and this site and there seems to be some reference to a cookie and/or priv command that may assist with resetting a ROMMON password but this particular router does not seem to understand either of these commands whilst in disable mode.
Excerpt follows:
TinyROM version 1.0(2)
Mon Nov 02 17:14:21 1998
Copyright (c) 1998 by cisco Systems, Inc.
All rights reserved.
POST ......... OK. 8MB DRAM, 8MB Flash.
Booting up ..
auto-boot: failed, "user abort"
boot> set
set baud =9600
set data-bits =8
set parity =none
set stop-bits =1
set console-flags =0
set mac-address =0050.7377.4CCA
set unit-ip =0.0.0.0
set serv-ip =0.0.0.0
set netmask =0.0.0.0
set gate-ip =0.0.0.0
set pkt-timeout =8
set tftp-timeout =16
set boot-action =flash
set file-name ="c800-g3-mw.120-1.XB1"
set watchdog =off
set prompt ="boot"
set ios-conf =0x2102
boot> set ios-conf = 0x142
ios-conf: failed, "permission denied"
boot> en
password:
enable: failed, "permission denied"
boot> en
password:
enable: failed, "permission denied"
boot> cookie
cookie: failed, "command not found"
boot> priv
priv: failed, "command not found"
Hope one of you guys can help.
Adrian

Hi,
Yes, if you get this boot prompt with the ">" and not "#" that means some joker set a ROMMON password without reading the documentation what is the impact of that (and not documenting it as well). You have to contact Cisco TAC to clear that password, it's not written in any documentation how to clear it.
Regards,
Dandy

Password recovery for mds

I have never worked on a MDS switch and I am tasked with password recovery on a mds9216. Please clarify the following step outlined in the recovery document. What command will I use from the switch(boot)# to find the correct file to load?? I am thinking
dev
dir flash
switch(boot)#load bootflash:san-ios.img

It would be dir bootflash: and the load command would work only san-ios.img is there. More than likely it looks more like this format: m9200-ek9-mz.2.1.2e.bin
But, yes, you have it in a nutshell. This is a sample of what it looks like if you don't have a SAN-OS on the bootflash:
Switch(boot)# config t
Switch(boot)(config)# interface mgmt 0
Switch(boot)(config-mgmt0)# ip address 172.18.172.57 255.255.255.0
Switch(boot)(config-mgmt0)# no shut
Switch(boot)(config-mgmt0)# exit
Switch(boot)(config)# ip default-gateway 172.18.172.1
Switch(boot)(config)# exit
Switch(boot)# copy tftp:m9500-sf1ek9-mzg.1.2.0.96.bin bootflash:m9500-sf1ek9-mzg.1.2.0.96.bin
Switch(boot)# load bootflash:m9500-sf1ek9-mzg.1.2.0.96.bin

License violation has been detected on the InterScan for CSC SSM

We are receiving this everyday at 1 AM, but there is no traffic on the network at this time. What can I do on the ASA or CSC to find out where and what this traffic is?
There are currently 559 active nodes while you only have 500 seats of license. 59 more seats of license is required.

This issue has confused us for a while too… Here’s the deal:
Even after the license violation the traffic for all the users will be scanned by the module. Despite the error message that you are seeing, the CSC will not drop connections due strictly to license violations. It is only a warning at this point.
With a high number of nodes, it is likely that you will overwhelm the CSC processing capacity. If the users are overly aggressive in their connections, they can easily max out the capacity.
Here's a high level link:
http://www.cisco.com/en/US/customer/products/ps6120/products_white_paper0900aecd805c3cd6.shtml
Can you increase the license? It only goes up to 1,000.
How can you tell what the count is? Use the following command from the ASA CLI:
show csc node-count yesterday
Here's the link:
http://www.cisco.com/en/US/docs/security/asa/asa72/command/reference/s2_72.html#wp1186101
Hope this helps!

Admin or Boot password recovery for an HP 2000

Hi,
I'm working on a wipe and reload of an HP 2000 laptop. The owner has forgotten the admin or boot up password, and after 3 tries it gives the code "66233711".
Whats the way forward on this?
Thanks,
Kevin
This question was solved.
View Solution.

Hi Kevin
Try this : 79191337
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Password Recovery for a GoLive site

Is there anyway to recover a password from a site that is built in GoLive? And if so how is it done. I've done internet searches and haven't found any way to do it.
I have an old GoLive site that I'm working on and need to recover the Password so I can move the site over to Dreamweaver.
thanks for your help.

The best option to deal with a forgotten password is to reset that password. Nobody should be using old passwords. That is a security risk. Passwords should be refreshed regularly. You can refresh a FTP password by contacting the hosting company. If the master account for the password is also not known, the hosting company can typically refresh that once you prove your identity by confirming the method of payment (credit card number).
There are two ways that I have recovered passwords from my own computer. These methods require that you have at least one program on your computer that can still connect to the FTP site.
One way is to 'sniff' your network traffic to see what plain text username and password is sent to the server. This will not work on SFTP connections (and is why you should use SFTP connections to be more secure).
The other way is to use a password revealer tool. Whenever you see a password field filled with asterisks, there is a password behind it that can be revealed.
Both of these methods can be accomplished with freeware. Should you look for these easy-to-find tools, be sure to get them from reputable sources. You should not want password revealer malware running on your computer that can secretly send your passwords home to the software's creator.

Password recovery for CSC-SSM

Similar Messages

Maybe you are looking for