Password recovery for linksys slm224g2 switch

what is password recovery for linksys slm224g2 switch

Hi Kalpesh.
Unfortunately this series of switches doesn't have a password recovery. Only the reset infront of the device.
If you have forgotten the device password you have to reset the switch to factory default to access the interface again.

Similar Messages

Password recovery for 2960 without loosing configuration

Hi,
I don't remember password for Cisco 2960 switch, now i want to recover the password. I have checked few documents but would like to know few things before following these steps.
1. Is password recovery procedure for Cisco 2960 switch is different from normal ctr+break then change the register method? As i am more confident of doing this procedure than using mode button and then renaming the configuration file.
2. If i follow below procedure then hope it won't erase the configuration including vlans information.?
https://supportforums.cisco.com/discussion/11756896/cisco-switch-29603560-password-recovery-and-factory-default-mode-button
3. Pressing mode button is an alternate to using ctrl+break sequence? and long pressing of mode button does't effect anything.
4. Restarting the switch after pressing mode button (without making any changes) will go back to previous configuration (working condition).
Thanks.

1. Is password recovery procedure for Cisco 2960 switch is different from normal ctr+break then change the register method? As i am more confident of doing this procedure than using mode button and then renaming the configuration file.
Password recovery for switches, like the Catalyst 2K and 3K, are far more simpler. Read this: Cisco Catalyst Fixed Configuration Layer 2 and Layer 3 Switches
2. If i follow below procedure then hope it won't erase the configuration including vlans information.?
https://supportforums.cisco.com/discussion/11756896/cisco-switch-29603560-password-recovery-and-factory-default-mode-button
I've posted a link above. I'd recommend you read that one. The link you've posted is about someone who wants to make a simple procedure look complicated.
3. Pressing mode button is an alternate to using ctrl+break sequence? and long pressing of mode button does't effect anything.
Correct. Get your mindset out of the password recovery of routers. When you are dealing with some models of switches, it's the "Mode" button. There are no "Mode" buttons in routers, hence, the Ctrl+Break key is required.
4. Restarting the switch after pressing mode button (without making any changes) will go back to previous configuration (working condition).
If you did NOT rename the configuration file, yes, the switch will reboot and load the existing configuration file.
If you renamed the configuration file, the switch will reboot. Finding no configuration file, the switch will load the factory defaulted configuration.

Password Recovery for Catalyst 6500

Hi all,
According to this website:
http://www.cisco.com/en/US/products/hw/switches/ps708/products_password_reco
very09186a00801349aa.shtml
Password will not be activated in the first 30 second, so when we want to do
the password recovery, we just press enter and quickly change the password.
I tried this in the Cat 6509 but found a different result. When I press
enter, it didn't go to console (prompt) instead, it keep asking me the
password.
Is there anything change in the password recovery for Cat 6500 (I've done it
before but when I try it again, it showed a different result). FYI, i use
this version of CatOS = cat6000-sup2k9.7-6-12.bin
Regards,
Affandi Indraji

Hi Friend,
There is no change in the password recovery procedure it is just that you might not be doing it fast enough in 30 seconds.
Just power off and power on the switch again and then immediately try hitting enter as soon as it prompts for the first password and then follow the same procedure what you used to do for other CATOS switches.
HTH, if yes please rate the post.
Ankur

Password recovery for mds

I have never worked on a MDS switch and I am tasked with password recovery on a mds9216. Please clarify the following step outlined in the recovery document. What command will I use from the switch(boot)# to find the correct file to load?? I am thinking
dev
dir flash
switch(boot)#load bootflash:san-ios.img

It would be dir bootflash: and the load command would work only san-ios.img is there. More than likely it looks more like this format: m9200-ek9-mz.2.1.2e.bin
But, yes, you have it in a nutshell. This is a sample of what it looks like if you don't have a SAN-OS on the bootflash:
Switch(boot)# config t
Switch(boot)(config)# interface mgmt 0
Switch(boot)(config-mgmt0)# ip address 172.18.172.57 255.255.255.0
Switch(boot)(config-mgmt0)# no shut
Switch(boot)(config-mgmt0)# exit
Switch(boot)(config)# ip default-gateway 172.18.172.1
Switch(boot)(config)# exit
Switch(boot)# copy tftp:m9500-sf1ek9-mzg.1.2.0.96.bin bootflash:m9500-sf1ek9-mzg.1.2.0.96.bin
Switch(boot)# load bootflash:m9500-sf1ek9-mzg.1.2.0.96.bin

Password Recovery for Wireless Lan controller

Hi, I am new to Wireless Lan Controller.
I just wanted to reset the password for the Controller. Can anybody help me with this. link/procedure anything will be appreciated.
Thanks & Regards,
Jvalin

I think they mean that they can not type "reset system" since they can't log in in the first place.
The key point to be made is that you need to restart the controller. So power it off if you can't login. Then console in to the controller and type "Recover-Config" as the username. This will default the configuration and allow you to start over with a new username/password.
There is no other password "recovery".

Password Recovery for Windows XP Pro

I have recently found a Dell computer in my house that is in good working condition. After setting the computer up, I asked the original owner what the administrator password to the login was. Sadly, the owner doesn't remember the password. I have tried logging in through safe mode and pressing ctrl+alt+del twice and trying to log in then. These tries didn't work, and I have been scavenging around for any password recovery tool I could use. On my recent trip to Best Buy, I informed one of the employees about the problem I had. To solve it, he said to restart the computer and while it was loading, continually press the F8 key, which should log me in as Administrator and could reset the password from there. I have tried this, but failed, most likely not sure if I did it right.

I hope this doesn't come off as mean/offensive, but if you don't have a higher level of computer knowledge, doing an account password reset isn't the easiest thing in the world.
Your local Geek Squad, or any repair shop, should be able to remove the password for you for a fee(call around to see what it is, when I was in store it was $29.99).
There are password removal tools out there, but it requires downloading a disk image, burning it, and getting the computer to boot off the disk into a command prompt environment. It's not "hard" but if you don't know what you're getting into, it's easy to mess things up.
If you like my post, or solution to your issue/question, go ahead and click on the little star by my name and/or accept the post as the Solution. It makes me happy.
I'm NOT an employee of Best Buy, or Geek Squad, though I did work as an Agent for a year 5 years ago. None of my posts are to be taken as the official stance that Best Buy will take on your situation. My advice is just that, advice.
Unfortunately, that's the bad luck of any electronic, there's going to be bad Apples... wait that's a horrible pun.

ROMMON Password Recovery for 803 Router

Hello Netpros.
Whilst attempting to perform a standard enable password recovery on an 803 router, I discovered that a ROMMON password had been set. This had the significant disadvantage in that I could not set the config register to bypass the configuration on startup using the set command.
I've browsed Google and this site and there seems to be some reference to a cookie and/or priv command that may assist with resetting a ROMMON password but this particular router does not seem to understand either of these commands whilst in disable mode.
Excerpt follows:
TinyROM version 1.0(2)
Mon Nov 02 17:14:21 1998
Copyright (c) 1998 by cisco Systems, Inc.
All rights reserved.
POST ......... OK. 8MB DRAM, 8MB Flash.
Booting up ..
auto-boot: failed, "user abort"
boot> set
set baud =9600
set data-bits =8
set parity =none
set stop-bits =1
set console-flags =0
set mac-address =0050.7377.4CCA
set unit-ip =0.0.0.0
set serv-ip =0.0.0.0
set netmask =0.0.0.0
set gate-ip =0.0.0.0
set pkt-timeout =8
set tftp-timeout =16
set boot-action =flash
set file-name ="c800-g3-mw.120-1.XB1"
set watchdog =off
set prompt ="boot"
set ios-conf =0x2102
boot> set ios-conf = 0x142
ios-conf: failed, "permission denied"
boot> en
password:
enable: failed, "permission denied"
boot> en
password:
enable: failed, "permission denied"
boot> cookie
cookie: failed, "command not found"
boot> priv
priv: failed, "command not found"
Hope one of you guys can help.
Adrian

Hi,
Yes, if you get this boot prompt with the ">" and not "#" that means some joker set a ROMMON password without reading the documentation what is the impact of that (and not documenting it as well). You have to contact Cisco TAC to clear that password, it's not written in any documentation how to clear it.
Regards,
Dandy

How to change SSID for Linksys wireless switch for PC?

imac-G5 Mac OS X (10.4.4)

Now, let's try to brake this issue down:
I need the Linksys to get a PC (Dell) running wireless. I installed a motorola PCI card for ethernet & the software that came with it in the PC. The switch does not read the network.
This involves a networking issue on a PC running Windows
The last time I spoke with Linksys they suggested http://192.168.1.1/same address, also 192.168.1.225. I get network connection errors.
This is an issue of your network setup
I have my Powerbook hard wired to the Motorola wireless router. My I-Mac is wireless.
So PowerBook & iMac work fine. Right?
You also have a Motorola Wireless Router, is this also your broadband modem?
I hooked up the Linksys switch to the modem with ethernet cat 5 cable. I still get connection errors. Neither computer can access these links. I get Motorola's broadband page with 192.168.1.1. I've done as much as I know but can't change the ssid if I can't access the Linksys switch. HELP Please!
This is a bit confusing:
What do you mean by connection errors? Unable to connect, able to connect but the connection drops?
Try this:
Shutdown your PC and both of your Macs
Turn of the Linksys switch and unplug it from the Motorola Router
Unplug the PowerBook which is wired to the Motorola and directly (with the same ethernet cable) connect it to the Linksys switch
Turn on the Linksys switch
Turn on your PowerBook
Open Safari or any other browser and go to: http://192.168.1.225 or http://192.168.1.225 (or whatever address Linksys told you)
Configure your Linksys switch (Change SSID) and save new settings
now, if everything goes fine, then:
Connect the PowerBook to the Motorola Router (just as it was before)
Connect the Linksys switch to the Motorola Router via an Ethernet Cable
Try to connect (from your PowerBook via Safari) to the Linksys switch@ http://192.168.1.225 or http://192.168.1.225 (or whatever address Linksys told you)
Keep the iMac and the PC shutdown untill you manage to set up the Linksys switch propperly
Post back feedback
a few Macs running 9.x, a bunch of Macs running 10.4.x and some serious SGI workstations running Irix 6.5.x
Message was edited by: fu

Password recovery for CSC-SSM

i have CSC ssm module in my lab. i forgot its username/password and also the ip address of csc module. when i tried to do reimgine the csc module, setup asks for ip address of csc module. is there is any way to recover password without knowing the ip address of CSC module.

This document describes how to recover a password on a Cisco ASA 5500 Series Content Security and Control Security Services Module (CSC-SSM) or the Advanced Inspection and Prevention Security Services Module (AIP-SSM) without having to re-image the device.
http://cisco.com/en/US/partner/products/ps6120/products_password_recovery09186a00807f5a59.shtml

Admin or Boot password recovery for an HP 2000

Hi,
I'm working on a wipe and reload of an HP 2000 laptop. The owner has forgotten the admin or boot up password, and after 3 tries it gives the code "66233711".
Whats the way forward on this?
Thanks,
Kevin
This question was solved.
View Solution.

Hi Kevin
Try this : 79191337
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Password Recovery for a GoLive site

Is there anyway to recover a password from a site that is built in GoLive? And if so how is it done. I've done internet searches and haven't found any way to do it.
I have an old GoLive site that I'm working on and need to recover the Password so I can move the site over to Dreamweaver.
thanks for your help.

The best option to deal with a forgotten password is to reset that password. Nobody should be using old passwords. That is a security risk. Passwords should be refreshed regularly. You can refresh a FTP password by contacting the hosting company. If the master account for the password is also not known, the hosting company can typically refresh that once you prove your identity by confirming the method of payment (credit card number).
There are two ways that I have recovered passwords from my own computer. These methods require that you have at least one program on your computer that can still connect to the FTP site.
One way is to 'sniff' your network traffic to see what plain text username and password is sent to the server. This will not work on SFTP connections (and is why you should use SFTP connections to be more secure).
The other way is to use a password revealer tool. Whenever you see a password field filled with asterisks, there is a password behind it that can be revealed.
Both of these methods can be accomplished with freeware. Should you look for these easy-to-find tools, be sure to get them from reputable sources. You should not want password revealer malware running on your computer that can secretly send your passwords home to the software's creator.

Need Manual For Linksys EFAH24 Switch

Hello,
I have tried to download the manual from Linksys, but for some reason the PDF link is dead. Does anyone know where else I can download a manual for this unit?
Thanks JR

Check this link, and click on Get Manual and then download the Manual on your Computer. I think it will help in settings up Hub.

HT1212 Password recovery for iTunes Back up.

I have recently backed up my iPhone through iTunes, however I cannot remember the password on the back up. Is there any way to recover the password?

By using the password of course, otherwise using password would is useless if we can get around it.

Cm administrator password recovery for 7.1 software

lost passwords on cm administrator 7.1 software

Use this command on CLI
utils reset_ui_administrator_password (Cisco Unified Communications Manager Only)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/cli_ref/7_1_3/cli_ref_713.html#wp42408
HTH
java
If this helps, please rate
www.cisco.com/go/pdihelpdesk

Password Recovery on UC540

Hi All
Our service provider has left and we need to make urgent changes to the UC - does anyone know the admin password recovery for the US540 ?

Hi Nuno,
You will need CLI access to the UC540 for this. I'm assuming that it has a password, and that you don't know what it is. If you have the password, skip password recovery step.
First, to recover/set a new password, during boot you need to send a break within 60 seconds which will take you to Rommon.
At Rommon 1> type confreg 0x2142
At Rommon 2> type reset. Type no after each set up question.
When it boots, you'll want to erase cue (voicemail) first. Session into CUE with: service-module integrated-service-engine 0/0 session and hit enter twice. Type offline, then y when asked to confirm. Type restore factory default, and again y when asked to confirm, and press enter to reload. It can take 5-10 mins, and you will know its complete when it says system online.
Then to factory default the UC/CME, type exit to get out of CUE. At the prompt (which should still end in a #, if not, type enable to go from > to #) type show flash: Show more, and probably down at the bottom of the list you'll see something like UC540-xxxxxxx-k9-FACTORY-xxx-.cfg This is the factory config file (don't save to it!) Make note of this filename, I will refer to it as (but make sure you include the name and .cfg). Type copy flash: startup. Reboot, you should be running with a factory defaulted UC540.
Best,
Charles
Please rate helpful posts.
Source: https://supportforums.cisco.com/thread/2157974
Lost password go to http://www.recoverlostpassword.com

Password recovery for linksys slm224g2 switch

Similar Messages

Maybe you are looking for