Password Reset for AIP-SSM 10

Hi,
i have an ASA5520 with v 7.2(2) running.
but the IPS module spftware is 5.1
when i tried to login to the > session 1
it prompts me for a login and password.
i tried cisco and a few other combinations.. but no luck ,,
how do i reset it ?? also that reset procedure on the docs says its resets password or the user cisco ..
how can i be sure if the user cisco even exists on it or not ?
any help please ???

no man it doesnt ..
the link u specified says it too..
hw-module module slot_number password-reset?This command recovers a password on a Cisco ASA 5500 Series Content Security and Control Security Services Module (CSC-SSM) or the AIP-SSM without having to re-image the device.
Note: This command starts support from IPS 6.0 (ASA 7.2 version) and is used to restore the Cisco CLI account password to the default cisco
hers my ASA and IPS details..
ASA# sh version
Cisco Adaptive Security Appliance Software Version 7.2(2)
Device Manager Version 5.2(2)
Compiled on Wed 22-Nov-06 14:16 by builders
System image file is "disk0:/asa722-k8.bin"
Config file at boot was "startup-config"
ASA up 22 days 3 hours
Hardware: ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
ASA# sh module 1
Mod Card Type Model Serial No.
1 ASA5500 SSM-10 ASA-SSM-10 B155670DW4
Mod MAC Add Range Hw Ver. Fw Ver. Sw Ver.
1 00xx to 001 1.0 1.0(10)0 5.0(2)S152.0
Mod SSM Apps. Name Status SSM Apps Version
1 IPS Up 5.0(2)S152.0
Mod Status Data Plane Status Compatibility
1 Up Up

Similar Messages

  • How to buy license? for AIP-SSM-10 ?

    Hi all
    how to buy license? for AIP-SSM-10 ?
    1. CON-SU1-AS1A1PK9 this is Cisco SMARTnet Support for AIP-SSM-10
    2. do I need smartnet for ASA ?
    3. what is part number of license ?
    ASA5510test# session 1
    Opening command session with slot 1.
    Connected to slot 1. Escape character sequence is 'CTRL-^X'.
    login: cisco
    Password:
    ***NOTICE***
    This product contains cryptographic features and is subject to United States
    and local country laws governing import, export, transfer and use. Delivery
    of Cisco cryptographic products does not imply third-party authority to import,
    export, distribute or use encryption. Importers, exporters, distributors and
    users are responsible for compliance with U.S. and local country laws. By using
    this product you agree to comply with applicable laws and regulations. If you
    are unable to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    ***LICENSE NOTICE***
    There is no license key installed on the SSM-IPS10.
    The system will continue to operate with the currently installed
    signature set.  A valid license must be obtained in order to apply
    signature updates.  Please go to http://www.cisco.com/go/license
    to obtain a new license or install a license.
    sensor#
    sensor# sh ver
    Application Partition:
    Cisco Intrusion Prevention System, Version 6.0(6)E3
    Host:
        Realm Keys          key1.0
    Signature Definition:
        Signature Update    S399.0                   2009-05-06
        Virus Update        V1.4                     2007-03-02
    OS Version:             2.4.30-IDS-smp-bigphys
    Platform:               ASA-SSM-10
    Serial Number:          ........
    No license present
    Sensor up-time is 21 min.
    Using 655507456 out of 1032499200 bytes of available memory (63% usage)
    application-data is using 39.7M out of 166.8M bytes of available disk space (25%
    usage)
    boot is using 37.6M out of 68.6M bytes of available disk space (58% usage)
    MainApp          N-NUBRA_2009_JUL_15_01_10_6_0_5_57   (Ipsbuild)   2009-07-15T01
    :15:08-0500   Running
    AnalysisEngine   N-NUBRA_2009_JUL_15_01_10_6_0_5_57   (Ipsbuild)   2009-07-15T01
    :15:08-0500   Running
    CLI              N-NUBRA_2009_JUL_15_01_10_6_0_5_57   (Ipsbuild)   2009-07-15T01
    :15:08-0500
    Upgrade History:
      IPS-K9-6.0-6-E3   17:48:06 UTC Wed Jul 15 2009
    Recovery Partition Version 1.1 - 6.0(6)E3
    sensor#

    Hi,
    CON-SU1-AS2A10K9 contract if for ASA+IPS bundle. If AIP-SSM-10 ws purchased as a spare the contract would be CON-SU1-ASIP10K9.
    I am not sure whether or not this Cisco Service for IPS contract can be  used to cover just the AIP-SSM-10 if it was purchased as part of a  Bundle instead of a Spare.
    I would recommend that you check with your Cisco reseller or Cisco  Sales Representative.
    Sourav

  • How to force password policy requirements on password resets for user accounts reset by the Administrator?

    OS: Windows Server 2008 R2 Enterprise
    Domain Level: 2008
    Forest Level: 2000
    We have Domain Administrators in our domain that reset passwords for user accounts, and the passwords the Administrators set them to are not being enforced follow our default domain password policy. For example, I log on the domain controller, as an administrator
    and can reset a password for a user account to be blank. 
    Is there a reason Domain Administrator password resets for user accounts are not enforced by our default domain password policy? Is there a way to enforce this on password resets by Domain Admins? 

    Do you have fine grant password policy? If not ; by default all the usrs are effected by domain level password policy even domain admins,
    Regards~Biswajit
    Disclaimer: This posting is provided & with no warranties or guarantees and confers no rights.
    MCP 2003,MCSA 2003, MCSA:M 2003, CCNA, MCTS, Enterprise Admin
    MY BLOG
    Domain Controllers inventory-Quest Powershell
    Generate Report for Bulk Servers-LastBootUpTime,SerialNumber,InstallDate
    Generate a Report for installed Hotfix for Bulk Servers

  • Signature Updates for AIP-SSM 10

    Hi all how can i obtain Signature Updates for AIP-SSM 10 where i am having 60 day trial license with me

    Here is the main file download page for the IPS sensors.
    Find the section for the version you are running and click on the Latest Signature Updates link to take to you to the download page for signature updates.
    You can then download which ever signature update you want.
    NOTE1: Each Signature Updates contains all signatures from previous Sig levels. So you only need to download the latest one.
    NOTE2: Each signature update has a specific E (Engine) level requirement. You can execute "show ver" on your sensor to determine if it is at an E1 or E2 level. If it is at E1 and you want the latest sigs that require E2 then you will first need to install the E2 upgrade.
    On that main download page look for the "Latest Upgrades" link for your version, and look for the IPS-engine-E2-req-X.X-X.pkg file where the X.X-X matches your sensor version.
    If there is not an X.X-X matching your sensor version, then you may need to upgrade the software version for your sensor as well.
    NOTE3: Many of these links will also require an account on cisco.com. And for some of these files that account may also need to be verified for being from a country where the USA's export restrictions allow downloads for encryption. (Most countries qualify but you do have to go through that qualification step). It has been over 10 years that I have had do this so I am not sure of the latest procedures for getting an account or validating it for encrpytion downloads.

  • How to generate license for AIP-SSM without PAK-number?

    Hello! I’m sorry for my English. I have a problem with generating license for AIP-SSM. My contract with SMARTnet service is activated, but I don’t have a PAK-number. How I can generate a license for updating my module?

    Alternatively you can always write an email to [email protected] with your serial number and they should be able to provide you the license for any cisco device.
    Sachin

  • Password reset for old sbcglobal account - no longer an ATT customer

    I have an account from my DSL service that I canceled some time ago. One of the sub-accounts was hacked and is suspended. I never set up alternate contacts for it, so it wants me to call a service rep to have the password reset. Since I am no longer a customer there is no path through the phone tree that I can tell to find someone to make this happen. Is it possible to have the password reset for this account?

    Sunflower75 wrote:
    I have the same problem... What number did u call? Please help.   and everyone else who posted on this thread, and including those who did NOT post to this therad, even if not an active customer, PLEASE, click on the link to the attcustomercare social media team here..  they try to catch what the can, but will always miss someone unless the send a private message, and the agreement says, automated help only after 60 days you are no longer an at^t customer, so these guys are going above and beyond to hep, even though technicaly they don't have to... but they need you to adk them first in the private message, or they won't know to help so.. here ya go:Rethink Possible
    Private Message (ATTCustomerCare for account specific help)
    Did a post have a solution that worked for you? Help other people find solutions faster by marking posts that helped you as an "Accepted Solution". Learn about accepted solutions here.

  • Need password reset for hp mini 1101

    need password reset for hp mini 1101cnu932bkxrplease help

    Hi: Please read this post which should resolve your dilemma. http://h30434.www3.hp.com/t5/Notebook-Operating-Sy​​​​​​​​​​​​​​​​​​​​​stems-and-Software/System-Halt​... Then... You can: 1. Use the unlock code you generated to enter the BIOS
    2. Disable all passwords that are enabled in the BIOS's security menu.
    3. If asked for current password - type the unlock code
    4. For new password, just press ENTER key
    5. Repeat the same for verify password column.

  • Password recovery for CSC-SSM

    i have CSC ssm module in my lab. i forgot its username/password and also the ip address of csc module. when i tried to do reimgine the csc module, setup asks for ip address of csc module. is there is any way to recover password without knowing the ip address of CSC module.

    This document describes how to recover a password on a Cisco ASA 5500 Series Content Security and Control Security Services Module (CSC-SSM) or the Advanced Inspection and Prevention Security Services Module (AIP-SSM) without having to re-image the device.
    http://cisco.com/en/US/partner/products/ps6120/products_password_recovery09186a00807f5a59.shtml

  • Need password reset for HP LaserJet M1536dnf MFP the same as others on this forum.

    I have the same M1536dnf password problem here, I can't access the settings.
    I can't activate the duplex mode without it.
    Thanks

    Hi @HPFix7,
    I see that you need the reset for the printer. I can help you.
    I can send you that information in a private message.
    In the forum beside your handle name just click on the envelope to view it.
    Have a wonderful day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Obtaining hardware and signature support for AIP SSM-10

    We have a 5510 which we have purchased an AIP SSM-10 card for the ASA which is already under a support contract. We now wish to add hardware maintenance for the new AIP SSM-10 card as well as signature updates. Our Cisco supplier will not confirm that we will receive signature updates with the hardware support though (we have been trying to get an answer from them since June or July now).
    Could someone let us know what the correct part number is so we can ask for the specific option that will provide both hardware cover and signature updates.

    i think this is what you need,
    CON-SU1-AS1A1PK9
    IPS SVC, AR NBD ASA5510-AIP10SP-K9
    cisco smartnet support

  • Why is wrong birthday information used when trying password reset for apple id

    When trying to do a password reset, icloud does not recognize the correct birthday information. The Email used to set up the apple II is no longer active so email reset is not an option.

    See Here.  Apple ID: Contacting Apple for help with Apple ID account security
    Ask to speak with the Account Security Team...
      Or Email Here  >  Apple  Support  iTunes Store  Contact
    AlMc6 wrote:
    ... had to open a new apple id, but my iphone keeps prompting me to sign on to my old one..
    Anything Downloaded with a Particular Apple ID is tied to that Apple ID and Cannot be Merged or Transferred to a Different Apple ID
    Apple ID FAQs  >  http://support.apple.com/kb/HT5622

  • Bios password reset for HP 6735s (not 6735b) laptop

    Recently, I managed to find a replacement board for my laptop however I found out that there was an issue with getting into the systems BIOS as there was a password set and the company I bought that board off had no clue what it was set to.
    Now I have tried all of the simple ways like removing the CMOS battery and trying the backdoor password (which I might add never worked) but still cant get into the bios to update it or change the boot sequence. I even requested some information about this issue directly to HP Support and they cant help due to the fact that the software they have to do this only work on 2009 and later models (my machine was built 2008).
    I have all the information including the UUID however cant seem to find either a DOS application that will succesfully view or reset the password or anyone that would be able to point me in the direction of such a appliocation.
    Before anyone says anything about a reset button or anything that simple, I have tried all that and have no such jumper or switch on the mainboard.

    Refer:
    http://forums.mydigitallife.info/threads/49497-HP-Probook-Elitebook-BIOS-Password-Reset-Utility?s=ad...
    Wish you luck,
    Karthik
    --Say "Thanks" by clicking the Kudos (purple thumbs up icon in the lower right corner of a post)
    --Please mark the post that solves your problem as "Accepted Solution"

  • Creating password reset for helpdesk in FIM 2010 R2

    I want my helpdesk to use FIM portal for resetting password.
    Helpdesk logs on to FIM portal.
    click custom page called password management
    Types the account name and get an option to 1- reset the password  2- Reset and send password to manager.
    can this be achieved ?
    Can some one guide me how to do this
    Creating custom page "password management" and other controls like user account name , reset password and reset and send password to manager .
    When helpdesk click on reset password , can a WF be called to reset the password in AD ?
    Any guidance will be helpful.
    AdiKumar

    Just this week i implemented such a feature at one of our customers. their helpdesk wants to be able to change all the password reset features which you can do in AD by their own.
    I've used Craigs fantastic Powershell Activity to archive this goal, Thanx Craig for sharing this piece of work to us all.
    So this solution goes like this:
    Create an additional tab with rcdc's on the users UI.
    Create a NewPW, doPWReset, ChangePWNextLogon and UnlockAccount Attribute and Binding for Users.
    NewPW always holds an default reset PW, but can be changed by helpdesk.
    MPR/Worksflow sets default values to any current and new user object for this attribute.
    Powershell workflow is triggert on changing any of this attributes.
    This Powershell reads the request and target object, determine the current state of the PWReset attributes and do all the appropriate actions with the Powershell AD command.
    After this i used the OOB Function Evaluator to reset all PWReset attributes to their default values.
    One thing as a little warning, be sure the workflow is not triggert if the FIMService account changed the PW attributes otherwise you get an endless loop, like me in my first tests ;-)
    Hope this helps
    Peter

  • Automatic Password Reset for end users

    Hello Experts,
    I am looking for a password reset facility, where end-users can reset their own password without depending on basis.
    we can trigger an password recovery question or trigger to authorised email id to simplify our basis efforts.
    Please let me know if you need more clarification about my requirement. I would greatly appreciate your help.
    Regards,
    Sarvesh

    Hi Rao,
    There is a good document on this.
    Have a look : http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/502c39b9-02e8-2d10-18a7-d32fade7b18b?QuickLink=index&…
    Also, if it's ABAP, why not give access SU3 to them. Only when the user gets locked or forgets password comes to your team.
    Divyanshu

  • Password reset for CM1415cfm colour laser

    Hi folks,
    I've recently bought a cm1415 printer over a month ago and stupidly setup a password when i set it up a couple of weeks ago, unfortunatley i've tried all passwords that i can think of but to no avail.
    Athough i can still print to it i can't access the setup on the network now and would like to change the fax settings.
    This printer is only for home/small business use for a four PC network so if someone can tell me how to do a master reset or preferable a workaround so that i don't lose how many pages/toner etc i've used. Worst case scenario if i need a master reset then i will do it if someone can can me how i've looked the documentation but i don see anything if i contact Hp directly and give them my invoice details could they reset it remotley ?.
    Any info please.

    Hi @kiborg777 ,
    I see that you need the reset for the printer.
    I can send you that information in a private message.
    In the forum beside your handle name just click on the envelope to view it.
    Have a nice day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

Maybe you are looking for