PATA SATA connections of hd(s) for least working conflicts

Just setting up my new unit and attempting to avoid conflicts when editing movies, transfering/recording music and my daily "stuff" by not having unneeded programs messing things up. My hope is (but not certain) that upon working in a different area, I can boot to CMOS, change the boot device and thereby eliminate a lot of the stuff that loads that is not needed for work at hand. I have the ability to connect 8 devices (4 PATA & 4 SATA). Here's my plan, what problems or suggestions might anyone give me?
Primary PATA Master = Hot Swap HD, will insert my daily work programs drive and can use for data/backup with other tasks (ext bay)
Pri PATA Sl = not used
Sec PATA MA = DVD Burner (ext bay)
Sec PATA Sl = not used
3rd SATA MA = Hot Swap HD used for data with movie editing, backup and transfer of data (ext bay)
4th SATA MA = Video editing programs drive (int bay)
5th SATA MA = Music transfering and recording programs drive
6th SATA MA = Not sure yet
The 4th ext bay will have the Creative Labs Live IR Box for front connections
Will this work, or should I take a different path of just using the hot swap drives.

There is no support of hotswap for PATA chl's.
I recommend you install OS on Pri Master PATA disk and leave this attached all the time .
Same with optical drive on Sec Master PATA chl .
The swap all you need on the sata ports .
This way you also avoid Harddisk boot order to change each time from removing/adding 1'st IDE master .

Similar Messages

My iPad keeps asking me for my password and I correctly put it in and it says I have no Wi-Fi connection but I have at least 2 bars on Wi-Fi. Any advice?

I got on my Music last night, and it kept asking me for it. I declined it, and it glitches out.
Then, I entered it, and it said it was wrong. But then I found out the password has been changed.
I used the new password, and then it said: Cannot Activate:Check your Wi-Fi connection.
I had at least two bars!! But it still didn't work.
Help?!?

Hi Strcow123,
Welcome to the Support Communities!
The article below may be able to help you troubleshoot your Wi-Fi issue.
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398?viewlocale=en_US
Reset network settings by tapping Settings > General > Reset > Reset Network Settings.
Note: This will reset all network settings including previously connected Wi-Fi networks and passwords
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/HT4199
I hope this information helps ....
Have a great day!
- Judy

PATA + SATA!!!!!!!!!!!

Ok.. I have the following system specs..
MSI Neo 2 -LS
Intel Pentium 4 2.8 ghz 800mhz
Corsair TWINX 512mb (256mb x 2) 3200mhz
Volcano 7+ Heatsink & Fan
Western Digital Raptor SATA
Western Digital Special Edition 120 gig
Western Digital Special Edition 120 gig
LiteOn 52x24x52 CD Burner
LiteOn 16x DVD-Rom
Prolink FX5200 128mb
Sound Blaster Audigy 2
US Robotics Modem
With 4 System Fans
Antec TruePower 550Watt
Ok I'm trying to get the following configuration Achieved..
Boot-up Hard Drive
Western Digital Raptor SATA
Storage Drives
Western Digital Special Edition 120 gig
Western Digital Special Edition 120 gig
CD ROMs
LiteOn 52x24x52 CD Burner
LiteOn 16x DVD-Rom
I've tried putting SATA in with Both Hard Drives on Master and CD-Rom's on Slave on IDE 1 and IDE 2.. I will not detect all the drives.. It will leave out what ever drive that is wants to.. I've set it to PATA + SATA and SATA 1 Channel..
I've also tried both hard drive on the same channel as in Master/Slave of IDE 1 and CD-Rom's on IDE 2.. Nothing that I do can work.. I know how to build system this board has some picky ways of doing things.. I still can't get into Ultra Turbo or Turbo mode either.. My DRAM voltage is up to 2.65 like everyone recommends. What am I don't wrong here..
Techman1013

since techman is using Neo2-LS, would the option to set "As Raid" be available? Cuz the LS version of the mobo doesnt come with the ICH5R rather it comes with the ICH5 chipset.
Techman,
Try settin the On-Chip ATA(s) Operate Mode to Native, this will allow you to have up to 6 devices connected, 2 SATA's and 4 PATA's, instead of 4 with Legacy Mode
ATA Configuration - S-ATA only (since you want the SATA drive the boot drive, i believe this option will allow you to set your SATA drive as Primary instead of Third w/ "P-ATA only)
P-ATA Keep Enabled - YES
P-ATA Channel Selection - Both
As for the RAID option, since you got the LS version of the mobo, I dont think it will let you change it to "Yes".

SSH - Failure to connect, does not prompt for password,

I have been using SSH on this iMac with 10.5.4 for over a year, upgraded to Leopard when it came out, never a problem with SSH, but now for no apparent reason, SSH fails when trying to connect through VPN into work.
I can still connect to other systems on the internet that are not through the VPN.
I don't suspect this to be a VPN issue because no other employees are having this problem with the VPN, using Mac, Windows or Linux. I can connect vi putty on my windows from the same network... below is my config.
Here is what I'm getting:
I connect as- ssh me@hostname and it returns "Permission denied (publickey)." It makes to attempt to prompt me for a password. I do not use a key on this system so it should prompt me for a password. I changed nothing on the system to cause ssh to break, But it's possible that a apple security update caused something to break.
I have added the following to my ~/.ssh/config file
PasswordAuthentication yes
My /etc/ssh_config file is as follows:
cat /etc/ssh_config
# $OpenBSD: ssh_config,v 1.22 2006/05/29 12:56:33 dtucker Exp $
# This is the ssh client system-wide configuration file. See
# ssh_config(5) for more information. This file provides defaults for
# users, and the values can be changed in per-user configuration files
# or on the command line.
# Configuration data is parsed as follows:
# 1. command line options
# 2. user-specific file
# 3. system-wide file
# Any configuration value is only changed the first time it is set.
# Thus, host-specific definitions should be at the beginning of the
# configuration file, and defaults at the end.
# Site-wide defaults for some commonly used options. For a comprehensive
# list of available options, their meanings and defaults, please see the
# ssh_config(5) man page.
# Host *
# ForwardAgent no
# ForwardX11 no
# RhostsRSAAuthentication no
# RSAAuthentication yes
PasswordAuthentication yes
# HostbasedAuthentication no
# GSSAPIAuthentication no
# GSSAPIDelegateCredentials no
# GSSAPIKeyExchange no
# GSSAPITrustDNS no
# BatchMode no
# CheckHostIP yes
# AddressFamily any
# ConnectTimeout 0
# StrictHostKeyChecking ask
# IdentityFile ~/.ssh/identity
# IdentityFile ~/.ssh/id_rsa
# IdentityFile ~/.ssh/id_dsa
# Port 22
# Protocol 2,1
# Cipher 3des
# Ciphers aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour,aes192-cbc,aes256-cbc
# EscapeChar ~
# Tunnel no
# TunnelDevice any:any
PermitLocalCommand yes
My /etc/sshd_config is:
cat /etc/sshd_config
# $OpenBSD: sshd_config,v 1.72 2005/07/25 11:59:40 markus Exp $
# This is the sshd server system-wide configuration file. See
# sshd_config(5) for more information.
# This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin
# The strategy used for options in the default sshd_config shipped with
# OpenSSH is to specify options with their default value where
# possible, but leave them commented. Uncommented options change a
# default value.
#Port 22
#Protocol 2,1
Protocol 2
#AddressFamily any
#ListenAddress 0.0.0.0
#ListenAddress ::
# HostKey for protocol version 1
#HostKey /etc/sshhostkey
# HostKeys for protocol version 2
#HostKey /etc/sshhost_rsakey
#HostKey /etc/sshhost_dsakey
# Lifetime and size of ephemeral version 1 server key
#KeyRegenerationInterval 1h
#ServerKeyBits 768
# Logging
# obsoletes QuietMode and FascistLogging
SyslogFacility AUTHPRIV
#LogLevel INFO
# Authentication:
#LoginGraceTime 2m
#PermitRootLogin yes
PermitRootLogin no
#StrictModes yes
#MaxAuthTries 6
#RSAAuthentication yes
#PubkeyAuthentication yes
#AuthorizedKeysFile .ssh/authorized_keys
# For this to work you will also need host keys in /etc/sshknownhosts
#RhostsRSAAuthentication no
# similar for protocol version 2
#HostbasedAuthentication no
# Change to yes if you don't trust ~/.ssh/known_hosts for
# RhostsRSAAuthentication and HostbasedAuthentication
#IgnoreUserKnownHosts no
# Don't read the user's ~/.rhosts and ~/.shosts files
#IgnoreRhosts yes
# To disable tunneled clear text passwords, change to no here!
#PasswordAuthentication yes
#PermitEmptyPasswords no
# SACL options
#SACLSupport yes
# Change to no to disable s/key passwords
#ChallengeResponseAuthentication yes
# Kerberos options
#KerberosAuthentication no
#KerberosOrLocalPasswd yes
#KerberosTicketCleanup yes
#KerberosGetAFSToken no
# GSSAPI options
#GSSAPIStrictAcceptorCheck yes
#GSSAPIKeyExchange yes
# GSSAPI options
#GSSAPIAuthentication yes
#GSSAPICleanupCredentials yes
# Set this to 'yes' to enable PAM authentication, account processing,
# and session processing. If this is enabled, PAM authentication will
# be allowed through the ChallengeResponseAuthentication mechanism.
# Depending on your PAM configuration, this may bypass the setting of
# PasswordAuthentication, PermitEmptyPasswords, and
# "PermitRootLogin without-password". If you just want the PAM account and
# session checks to run without PAM authentication, then enable this but set
# ChallengeResponseAuthentication=no
#UsePAM yes
#AllowTcpForwarding yes
#GatewayPorts no
#X11Forwarding no
#X11DisplayOffset 10
#X11UseLocalhost yes
#PrintMotd yes
#PrintLastLog yes
#TCPKeepAlive yes
#UseLogin no
#UsePrivilegeSeparation yes
#PermitUserEnvironment no
#Compression delayed
#ClientAliveInterval 0
#ClientAliveCountMax 3
#UseDNS yes
#PidFile /var/run/sshd.pid
#MaxStartups 10
#PermitTunnel no
# no default banner path
#Banner /some/path
# override default of no subsystems
Subsystem sftp /usr/libexec/sftp-server
# Example of overriding settings on a per-user basis
#Match User anoncvs
# X11Forwarding no
# AllowTcpForwarding no
# ForceCommand cvs server

Also I forgot to mention, I have nulled out the known_hosts file to eliminate any conflicts there, I have verified .ssh is 700 and files config and known_hosts are 600
output using ssh -v
debug1: Reading configuration data /Users/<me>/.ssh/config
debug1: Reading configuration data /etc/ssh_config
debug1: Connecting to pshx4105a [216.255.177.213] port 22.
debug1: Connection established.
debug1: identity file /Users/<me>/.ssh/identity type -1
debug1: identity file /Users/<me>/.ssh/id_rsa type -1
debug1: identity file /Users/<me>/.ssh/id_dsa type -1
debug1: Remote protocol version 2.0, remote software version OpenSSH_4.5p1 FreeBSD-20061110
debug1: match: OpenSSH_4.5p1 FreeBSD-20061110 pat OpenSSH*
debug1: Enabling compatibility mode for protocol 2.0
debug1: Local version string SSH-2.0-OpenSSH_4.7
debug1: SSH2MSGKEXINIT sent
debug1: SSH2MSGKEXINIT received
debug1: kex: server->client aes128-cbc hmac-md5 none
debug1: kex: client->server aes128-cbc hmac-md5 none
debug1: SSH2MSG_KEX_DH_GEXREQUEST(1024<1024<8192) sent
debug1: expecting SSH2MSG_KEX_DH_GEXGROUP
debug1: SSH2MSG_KEX_DH_GEXINIT sent
debug1: expecting SSH2MSG_KEX_DH_GEXREPLY
debug1: Host 'pshx4105a' is known and matches the DSA host key.
debug1: Found key in /Users/<me>/.ssh/known_hosts:3
debug1: sshdssverify: signature correct
debug1: SSH2MSGNEWKEYS sent
debug1: expecting SSH2MSGNEWKEYS
debug1: SSH2MSGNEWKEYS received
debug1: SSH2MSG_SERVICEREQUEST sent
debug1: SSH2MSG_SERVICEACCEPT received
debug1: Authentications that can continue: publickey
debug1: Next authentication method: publickey
debug1: Trying private key: /Users/<me>/.ssh/identity
debug1: Trying private key: /Users/<me>/.ssh/id_rsa
debug1: Trying private key: /Users/<me>/.ssh/id_dsa
debug1: No more authentication methods to try.

How to permanently remove "This Connection is Untrusted" notification for all future websites everywhere forever?

Dear Mod/Helper/Whoever
Please read this entire post before answering since it addresses virtually all the most popular "solutions" for this problem and they DON'T WORK.
I've already found this and it was of no use: https://support.mozilla.org/en-US/questions/1015256?esab=a&as=aaq
The moderator's blatant copy-paste response was an insult and not helpful at all.
My system date is ok and the cause of invalid certificate is the LEAST of my concerns. I just want to browse the website and not get ANY warnings about ANY invalid certificates or ANY risks involved, period. All popular workarounds with settings/advanced/validity properties have been tried but none of them fix this for me. I want FF to accept all invalid certificates instantly without notification or warning, no matter what.
I want to remove the warning screen "This Connection is Untrusted" permanently for all future references, so that I don't even see any errors related to it when I browse a website.
I'm not here to argue the merits or lack thereof for this action, I just want to get rid of it.
I'm running a lot of custom software on my comp and I have 3 LAN cards connecting me to 3 different networks with varying degrees of security and this notification is a huge pain in the... back, because it eats my time every day.
I've been using Firefox for years exactly because it didn't have stuff like this in the past - I could visit all the funny/suspicious/malicious websites without problems, where IE would have died 10 times over. Sadly that FF feature began changing to the worse in the past years, an ever-increasing slope downwards for this once great web browser.
I KNOW all the risks involved and I don't care. In fact I encourage websites to try and install "stuff" on my computer because as I mentioned, this is a special computer. I'm visiting 40-50 websites with that prompt DAILY because that's what I do for a living. Every time I have to add an exception is a wasted effort and time. I'm running other browsers as well but FF is my focus due to its popularity.
Please for the love of all that is sacred, provide some sort of workaround for this without the need to install an addon or click "I understand the risks" a gazillion times. An "about:config" variable would be nice but apparently it's not there, I looked.

That is not possible as that would expose you and other Firefox users to unacceptable security vulnerabilities.
The normal procedure is to contact the website maintainer and ask them to fix the certificate chain or install missing root certificates in Firefox and set the trust bits accordingly.
If you do not care about certificates then why don't you install proxy software and use that proxy and let it handle the certificates and import the root certificate of that proxy in Firefox?

KT4 Ultra Ide3/Sata connection problem

I have had this motherboard for about a year and have now decided to utilise one of the sata connection. the problem i am having is that i cant get either the bios to recognise a drivr connected to eide 3.
i have tried to rebiuld the system with a hard drive connected to the sata connector but cant get windows to recognise the sata drive.

control plus f and make an array
set scsi second to cdrom in boot order
f6 as xp install starts feed in raid drivers

JDBC Connections in Oracle9iAS Containers for J2EE

does anyone have an idea as to what jdev libraries aside from j2ee and jdbc that i can include to get the OTN article "JDBC Connections in Oracle9iAS Containers for J2EE" to at least compile?
Thank you
Jim
The url for the excellent article is;
http://www.oracle.com/technology/sample_code/tech/java/codesnippet/j2ee/jdbc/JDBC_in_J2EE.html

gday to you mate!
The solution is probably very simple it is just that i can't see it. i am getting the following messages from jdev9.0.5.2 build 1618 debug with the j2ee and Oracle JDBC libraries on this code:
60 javax.naming.InitialContext ic = new javax.naming.InitialContext();
61 oracle.jdbc.pool.OracleConnectionPoolDataSource ds = (oracle.jdbc.pool.OracleConnectionPoolDataSource)ic.lookup("jdbc/pool/OracleConnectionPoolDS");
62 oracle.jdbc.pool.OraclePooledConnection pc = ds.getPooledConnection();
63 oracle.jdbc.driver.OracleConnection conn1 = pc.getConnection();
Project: C:\JDev\jdev\mywork\DVDOrdering\ViewController\ViewController.jpr
C:\JDev\jdev\mywork\DVDOrdering\ViewController\src\view\InsertOrder.java
Error(62,86): incompatible types; found: javax.sql.PooledConnection, required: oracle.jdbc.pool.OraclePooledConnection
Error(63,82): incompatible types; found: java.sql.Connection, required: oracle.jdbc.driver.OracleConnection
Thanks again!

K9A2 platnium sata connections

ok well i have a k9a2 platnium.
i keep thinking that my cables are all wrong for the sata connections.
ok well i have a :
2x 80gb sata drives 3.0gb/s HDD
1x 640gb sata drive 3.0 gb/s HDD
1x Samsung 22x DVD burner SATA
where do i connect the 2x 80gb for a raid 0.
do i just connect it all into the sata 1-4?
or do i put the 640 into sata1. samsung in the sata2 and the 80gb in the sata5-6?

yes i have. actually i own the k9a2 platnium. i was just wondering where i should put my sata cables

K9N2 Diamond SATA Connections

I have a total of 6 SATA connections on this mobo. The two facing and the four to the right. My case is the CM Comos S. One SATA slot is used up by the front panel. I have 2 DVD drives and 2 HDD's. I have the front panel, both dvd's and my main HDD plugged into the four slot area. Looking at the front of the board, SATA6, is the only remaining open slot. SATA5 is blocked by the vid card. I connected cables, but the new drive is not detected. Why? also in BIOS it only mentions SATA's 1,2,3 and 4. Can someone please help?

Ok. Google the raid questions. There are several different types each has it's specific characteristics from raid 0 to jbod. It is way to much information to give via a forum chat. Benefits are data redundancy for some, data access times for others, combinations of those two characteristics with others. Do some research. Your manual will also give you some instruction. If it's a new install take your time, do your research on raid and make the decision for yourself. Further, with the new install you won't have to retro the AHCI to enable the 5 and 6 sata ports.
Quote from: tomween1 on 07-March-10, 08:18:41
aren't SATA 5 & 6 specifically for a raid set up?I presume then, that all 6 SATA connections are not the same.
Sorry I missed these questions. No 5 and 6 aren't specifically for a raid setup...I believe sata 1-4 use the nvidia raid controller and support up to 4 devices and the 5 and 6 ports are for silicon image controller and support only 2 devices. Anyway, check your manual or download one. It will tell you.

I am having trouble getting my ipad to recognize the sat connection have turned off and back on it shows there but does not load safari

I am having trouble getting my ipad to communicate with sat connection I have tried turning off and on re installing the sat connection but still cannot get safari to load

Hello Brenda,
Thank you for the details of the issue you are experiencing with your iPad. It sounds like you're not able to access the Internet on your iPad. I found a couple of resources that will help.
If you are having trouble connecting to the Internet using Wi-Fi, I recommend the following article:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
If you are not able to access the Internet when connected to a cellular network, I recommend the following article:
iPad (Wi-Fi + Cellular Models): Troubleshooting a cellular data connection
http://support.apple.com/kb/TS4249
Thank you for using Apple Support Communities.
Best,
Sheila M.

SATA connection on Qosmio X870 Bt3G23

Hello
I bought last month Qosmio X870 Bt3G23, now I'm planning to add SSD as my primary drive for OS and daily use programs.
I was wondering what kind of SATA connection does my laptop come with, is it SATA II or SATA III
If anyone know what kind of SATA connection does Qosmio X870 Bt3G23 come with, please let me know and I would be very appreciated

I called Toshiba Tech Support with that question and did not get the clear answer I expected. The interface on Qosmio X870-BT3G23 seems to be a SATA-II.
Usually a manufacturer would advertise the best features available if they are being offered in a product. I was disappointed but I might nevertheless order the Qosmio X870-BT3G23. I also wonder if there are yet on the market any laptops with a SATA-III interface.
As for adding an SSD, there should be no problems. SATA-III SSDs are backward compatible with SATA-II interface. I have successfully used an OSZ Vertex 4 and a Crucial m4 on old laptops.

PATA - SATA adapter

I want to connect my Maxtor PATA HD to the SATA controller of the KT6 Delta SR. I have found a PATA-SATA adapter by ASUS, the "DONGLE".
Did someone try it ? Does it work well on the MSI motherboards?
Thanks in advance

No, I don't want to use the SATA connector to increase the performance, but to connect more storage devices: I have a CD writer, a DVD reader, and 3 HD to connect.

P67A-GD65 new system bios setting recommendations and sata connections

Hey all,
My old dual core HTPC (after many hours of use) finally gave up the ghost and moved on to the great PC grave yard . I have ordered all the new upgrade parts from Newegg and am looking for recommendations on what bios settings and setup procedures I should use on the initial bootup and Windows load. I'm not looking to overclock I just want a fast stable system for video decoding and playback. It's my understanding from the manual that SATA 1-2 are controlled by the Intel P67 chip and 7-8 are controlled by the Marvell chip but I am unsure of SATA 3-6. Can SATA 3-6 do raid 0? I want to use the Crucial SSD as my primary boot drive and the 2 WD drives on raid 0 as my secondary drive. SATA connection advice (which SATA ports) and Raid Bios setting would be helpful. Should I install the raid 0 drives after I have Windows 7 loaded on the SSD? Any other setup advice is appreciated.
Here is my setup.
Windows 7 64bit
Bach HTPC case
Ultra LSP 750Pro PSU
Intel i5-2500 3.3G CPU
MSI P67A-GD65 Motherboard
Sapphire HD5570 1G RT Video Card
Crucial CTFDDAC128MAG-1G1 SSD 6.0Gb/s SATAIII (Primary boot drive)
2 WD3200KS Hard Drives SATA 3.0Gb/s (Raid 0)
Lite-on 12X Blu-Ray Burner SATA
G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600

Two questions answered. SATA 3-6 are controlled by the Intel P67 chip and do support Raid 0 but I still wonder if I should wait to install the drives until Windows has finished it's install.
SATAIII controller integrated in Intel® P67 & Marvell SE9128 chipsets
- Up to 6Gb/s transfer speed.
- Supports two SATAIII ports (SATA1~2) by P67 PCH
- Supports two SATAIII ports (SATA7~8) by Marvell SE9128
- SATA1~6 ports support RAID 0/1/5/10 mode by Intel P67 PCH
- SATA7~8 ports support RAID 0/1 mode by Marvell SE9128

Do I need to keep my external hard drive connected at all times for time capsule?

Do I need to keep my external hard drive connected at all times for time capsule?

Hi,
I have a similar question. I have backed up my external hard drive through my computer, onto my TC. When I go into TM, it doesn't show the external hard drive unless it is connected to the computer. Can I access the info from the external hard drive that is on the TC if I don't have the hard drive plugged in? If so, how can I do that?
Thanks,
Bernadette

Firefox connects to google-analytics for some sites, and then gets stuck, and I can never get onto the site. How do I prevent Firefox from connecting to google-analytics? I use XP with service pak 3 in English

Firefox connects to google-analytics for some sites,when i click on links in websites or emails and then gets stuck, and I can never get onto the site. Or opens a new bower behind the one i'm usind that's blank i don't even know it's there untill i close the one i'm using. How do I prevent Firefox from connecting to google-analytics? Or opening a blank bowser behind the one i'm using. I use XP with service pak 3 in English
== This happened ==
A few times a week
== a couple months ago

I got the same issue.
I go on a website and all the sudden another window pops up with "results.google-analytics.com" or "search.google-analytics.com". It has often ads for other sites for example. black single dating site
how can I can I stop that from happening again?
I didn't download or do anything, just visit websites, that I visit on a regular basis.
OS: Windows XP
Firefox Version: 3.6.6

PATA SATA connections of hd(s) for least working conflicts

Similar Messages

Maybe you are looking for